Professional Documents
Culture Documents
Sira 05ATEX2084X Issue 9 (IS-mini Range)
Sira 05ATEX2084X Issue 9 (IS-mini Range)
II 1 G I M1
Ex ia IIC T4 Ga (-40°C ≤ Ta ≤ +60°C) Ex ia I Ma (-40°C ≤ Ta ≤ +60°C)
Page 1 of 7
DQD 544.09 Rev 2018-04-20
SCHEDULE
13 DESCRIPTION OF EQUIPMENT
The IS-mA1 Sounder is designed to provide an audible warning when activated. It consists of the
following mounted in an IP 65, flame retardant, ABS enclosure:
• Sounder printed circuit board assembly • Inductive sounder transducer
External connections are made to terminals mounted on the sounder printed circuit board via cable entry
devices mounted in the wall of the enclosure. The parameters for the IS-mA1 Sounder are as follows:
Terminals Parameters
Ui Ii Pi Ci Li
Terminal + w.r.t. Terminal - 28 V 93 mA 660 mW 0 0
Terminals S2 and S3 w.r.t. Terminal - 28 V 0 - - -
The IS-mB1 Beacon is designed to provide a flashing warning when activated. It consists the following
mounted inside an IP 65, flame retardant, ABS enclosure that is fitted with a transparent polycarbonate ‘lens’:
• Beacon main printed circuit board assembly • Beacon LED printed circuit board assembly
External connections are made to terminals mounted on the beacon main printed circuit board via cable entry
devices mounted in the walls of the enclosure. The parameters for the IS-mB1 Beacon are as follows:
Terminals Parameters
Ui Ii Pi Ci Li
Terminal + w.r.t. Terminal - 28 V 660 mA 1.2 W 0 0
The IS-mC1 Combined Sounder/Beacon is designed to provide an audible and a flashing warning
when activated. It consists of the following mounted inside an IP 65, flame retardant, ABS enclosure
that is fitted with a transparent polycarbonate ‘lens’:
• Sounder printed circuit board assembly • Beacon main printed circuit board assembly
• Inductive sounder transducer • Beacon LED printed circuit board assembly
External connections are made to terminals mounted on the sounder printed circuit board assembly and
the beacon main printed circuit board assembly via cable entry devices mounted in the walls of the
enclosure. The IS-mC1 Combined Sounder/Beacon may be supplied with internal wiring connections
between Sounder Terminals + / - and Beacon Terminals + / -, alternatively these connections may be
fitted by the user/installer. The parameters for the IS-mC1 Combined Sounder/Beacon are as follows:
Terminals Parameters
Ui Ii Pi Ci Li
Without internal Sounder Terminals + w.r.t. Sounder Terminals - 28 V 93 mA 660 mW 0 0
connections: Sounder Terminals S2 & S3 w.r.t. Sounder Terminals - 28 V 0 - - -
Beacon Terminal + w.r.t. Beacon Terminal - 28V 660 mA 1.2 W 0 0
With internal Sounder Terminal + w.r.t. Sounder Terminal - 28 V 93 mA 660 mW 0 0
connections Sounder Terminals S2 & S3 w.r.t. Sounder Terminals - 28 V 0 - - -
This certificate and its schedules may only be CSA Group Netherlands B.V.
reproduced in its entirety and without change Utrechtseweg 310,
6812 AR, Arnhem Netherlands
This certificate and its schedules may only be CSA Group Netherlands B.V.
reproduced in its entirety and without change Utrechtseweg 310,
6812 AR, Arnhem Netherlands
This certificate and its schedules may only be CSA Group Netherlands B.V.
reproduced in its entirety and without change Utrechtseweg 310,
6812 AR, Arnhem Netherlands
• The equipment shall only be supplied via Sounder Terminals + w.r.t. Sounder Terminals – from a
barrier having a maximum open circuit voltage Uo that is ≤28 V and a maximum short circuit current
Io that is ≤93 mA, where Io is resistively limited. The barrier shall be ATEX certified by a notified
body.
• If not already fitted, optional internal wiring connections between Sounder Terminals + / - and
Beacon Terminals + / - may be fitted by the user. The wiring used for such connections shall have a
minimum radial thickness of insulation of 0.5 mm.
15.4 Conditions for IS-mA2 Sounder
• The equipment has an ingress protection rating of IP65. However, as cable entry is via a ‘knockout’
in the bottom of the enclosure base, the user shall ensure that this enclosure base is sealed to
whatever it is attached by a method that provides ingress protection appropriate to the environment
in which it installed i.e. IP20 or better. An ‘O’ ring fitted within the outer rim of the bottom of the
enclosure base may be used for this purpose.
• The total capacitance connected to Terminals + w.r.t. – (i.e. the capacitance of the cable plus any
other capacitance) shall not exceed 83 nF.
• The enclosure is non-conducting and may generate an ignition-capable level of electrosatic charges
under certain extreme conditions. The user should ensure that the equipment is not installed in a
location where it may be subjected to external conditions that might cause a build-up of electrostatic
charges on non-conducting surfaces, additionally, cleaning of the equipment should be done only with
a damp cloth.
• The equipment shall only be supplied via Terminals + w.r.t. Terminals – from a barrier having a
maximum open circuit voltage Uo that is ≤28 V and a maximum short-circuit current Io that is
≤93 mA, where Io is resistively limited. The barrier shall be ATEX certified by a notified body.
15.5 Conditions for IS-mA3 Sounder
• The equipment has an ingress protection rating of IP65. However, as cable entry is via a ‘knockout’
in the bottom of the enclosure base, the user shall ensure that this enclosure base is sealed to
whatever it is attached by a method that provides ingress protection appropriate to the environment
in which it installed i.e. IP20 or better. An ‘O’ ring fitted within the outer rim of the bottom of the
enclosure base may be used for this purpose.
• The total capacitance connected to Terminals + w.r.t. Terminals S2 and S3 (i.e. the capacitance of
the cable plus any other capacitance) shall not exceed 83 nF.
• The enclosure is non-conducting and may generate an ignition-capable level of electrosatic charges
under certain extreme conditions. The user should ensure that the equipment is not installed in a
location where it may be subjected to external conditions that might cause a build-up of electrostatic
charges on non-conducting surfaces, additionally, cleaning of the equipment should be done only with
a damp cloth.
• The equipment shall only be supplied via Terminals + w.r.t. Terminals S2 and S3 from a barrier having
a maximum open circuit voltage Uo that is ≤28 V and a maximum short-circuit current Io that is ≤93
mA, where Io is resistively limited. The barrier shall be ATEX certified by a notified body.
This certificate and its schedules may only be CSA Group Netherlands B.V.
reproduced in its entirety and without change Utrechtseweg 310,
6812 AR, Arnhem Netherlands
This certificate and its schedules may only be CSA Group Netherlands B.V.
reproduced in its entirety and without change Utrechtseweg 310,
6812 AR, Arnhem Netherlands
Issue 0 to 2 (The drawings listed with these Issues were rationalised and superseded by those detailed in Issue 3)
Issue 3
Drawing Sheets Rev. Date Title
CD 5011 1 of 1 A 09 May 05 Circuit Diagram - Sounder Board
CD 5012 1 of 1 A 09 May 05 Circuit Diagram - Beacon Board
D 5014 1 of 1 A 03 Jun 05 Certification Label - Sounder - ATEX
D 5015 1 of 1 C 21 Apr 06 Certification Label - Beacon - ATEX
D 5016 1 of 1 C 21 Apr 06 Certification Label - Combined Sounder / Beacon - ATEX
D 5017 1 of 1 A 01 Aug 05 General Assembly - Sounder
D 5018 1 of 1 A 03 Jun 05 General Assembly - Beacon
D 5019 1 of 1 A 01 Aug 05 General Assembly - Combined Sounder / Beacon
D 5021 1 of 1 A 24-Jun-05 PCB Assembly - Sounder
PL 5021 1 of 1 A 03 Jun 05 Parts List - Sounder PCB
D 5022 1 of 1 A 24 Jun 05 PCB Assembly - Beacon
PL 5022 1 of 1 A 03 Jun 05 Parts List – Beacon PCB
D 5032 1 of 1 A 29 Jun 06 Certification Label – Sounder – ATEX/IECEx/FM
D 5033 1 of 1 A 29 Jun 06 Certification Label – Beacon - ATEX/IECEx/FM
D 5034 1 of 1 A 29 Jun 06 Certification Label – Combined Sounder/Beacon - ATEX/IECEx/FM
Issue 4
Drawing Sheets Rev. Date Title
CD 5041 1 of 1 A 17-Oct-06 Circuit Diagram - IS-mA2 and IS-mA3 Sounders
D 5041 1 of 1 A 17-Oct-06 PCB Assembly - IS-mA2 and IS-mA3 Sounders
PL 5041 1 of 1 A 02 Aug 06 Parts List - IS-mA2 Sounder
D 5042 1 of 1 A 02 Aug 06 General Assembly - IS-mA2 and IS-mA3 Sounders
PL 5042 1 of 1 A 02 Aug 06 Parts List IS-mA3 Sounder
D 5043 1 of 1 A 02 Aug 06 Certification Labels - IS-mA2 Sounder
D 5044 1 of 1 A 02 Aug 06 Certification Labels - IS-mA3 Sounder
Issue 5
Drawing Sheets Rev. Date Title
CD 5011 1 of 1 A 09 May 05 Circuit Diagram - Sounder Board
D 5017 1 of 1 A 01 Aug 05 General Assembly - Sounder
D 5021 1 of 1 A 24 Jun 05 PCB Assembly - Sounder
PL 5021 1 of 1 A 03 Jun 05 Parts List - Sounder PCB
D 5051 1 of 1 A 12 Dec 06 Certification Label ATEX - IS-mA1M Sounder
Issue 6
Drawing Sheets Rev. Date (Sira stamp) Title
D 5032 1 of 1 B 11 Nov 09 IS-mA1 Sounder Label (ATEX, IECEx, FM)
D 5033 1 of 1 B 11 Nov 09 IS-mB1 Beacon Label (ATEX, IECEx, FM)
D 5034 1 of 1 B 11 Nov 09 IS-mC1 Combined Label (ATEX, IECEx, FM)
D 5043 1 of 1 B 11 Nov 09 IS-mA2 Sounder Label (ATEX, IECEx, FM)
This certificate and its schedules may only be CSA Group Netherlands B.V.
reproduced in its entirety and without change Utrechtseweg 310,
6812 AR, Arnhem,
Netherlands
This certificate and its schedules may only be CSA Group Netherlands B.V.
reproduced in its entirety and without change Utrechtseweg 310,
6812 AR, Arnhem,
Netherlands