Professional Documents
Culture Documents
Service Mode, Troubleshooting - Toshiba - E-Studio 4508A - Maintenance. PM Display2
Service Mode, Troubleshooting - Toshiba - E-Studio 4508A - Maintenance. PM Display2
Service Mode, Troubleshooting - Toshiba - E-Studio 4508A - Maintenance. PM Display2
Catalog
Sign In
Contacts
Forum Eng
0 USD 0.00
Discount 0.0
0.0%%
Parts List
0
PM display conditions
The conditions of the PM display consist of the codes of the 08 Setting Mode for “the setting value
treated as a threshold of the PM display”, “the counter indicating the current number of prints and
driving time” and “the setting value which determines the display conditions”. The PM timing is
displayed when the counter exceeds the setting value according to the display condition based on
“the setting value which determines the display conditions”.
• Setting value treated as a threshold of the PM display
Notes: When “0” is entered as the setting value, PM timing is not displayed.
FS-08-6190: Setting value of PM counter [process unit (K)]
FS-08-6191: Setting value of PM time counter [process unit (K)]
FS-08-5554: Setting value of PM counter [developer material (K)]
FS-08-5555: Setting value of PM time counter [developer material (K)]
FS-08-5562: Setting value of PM counter [parts other than the PM parts of the process unit]
FS-08-5563: Setting value of PM time counter [parts other than the PM parts of the process unit]
• Counter indicating the current number of prints and driving time
FS-08-6194: Current value of PM counter [process unit (K)]
FS-08-6195: Current value of PM time counter [process unit (K)]
FS-08-5568: Current value of PM counter [developer material (K)]
FS-08-5569: Current value of PM time counter [developer material (K)]
FS-08-5576: Current value of PM counter [parts other than the PM parts of the process unit]
FS-08-5577: Current value of PM time counter [parts other than the PM parts of the process unit]
• Setting value which determines the display conditions
FS-08-6198: Switching of output pages/driving counts at PM [process unit (K)]
FS-08-5581: Switching of output pages/driving counts at PM [developer material (K)]
FS-08-5585: Switching of output pages/driving counts at PM [parts other than the PM parts of the
process unit]
For example, you can set the conditions of the PM display of the [process unit (K)] as follows.
PM display by specifying the number 1. Key in “0” for FS-08-6198 (Switching of output
of prints pages/driving counts at PM [process unit (K)])
2. Key in the value of the number of prints for the PM
display other than “0” for FS-08-6190 (Setting value of
PM counter [process unit (K)]).
1. Key in “1” for FS-08-6198 (Switching of output
pages/driving counts at PM [process unit (K)]).
PM display by specifying the driving
2. Key in the value of the driving time for the PM
time
display other than “0” for FS-08-6191 (Setting value of
PM time counter [process unit (K)]).
1. Key in “2” for FS-08-6198 (Switching of output
pages/driving counts at PM [process unit (K)]).
2. Key in the value of the number of sheets for the PM
PM display by the earlier one: when
display other than “0” for FS-08-6190 (Setting value of
the number of prints or the driving
PM counter [process unit (K)]).
time reaches the set value
3. Key in the value of the driving time other than “0”
for FS-08-6191 (Setting value of PM time counter
[process unit (K)]).
If the value of FS-08-9891 (Warning message on the touch panel when PM time has come) is set to
“0: No warning notification”, the PM display is not performed regardless of the settings above.
(Default value is “1: Display warning notification”)
PM display contents
When the counter value exceeds the setting value, the equipment notifies you of when the
maintenance time has come by displaying the message “Time for periodic maintenance ****” on the
control panel LCD. “****” in the message is a 4-digit hexadecimal number code. This number is
allocated in the following manner, therefore the parts needing maintenance can be identified.
PM parts of the process unit (K): 0008
PM parts of the developer material (K): 0080
Parts other than the PM parts of the process unit: 0100
If multiple parts have reached the maintenance time, the sum of the corresponding code values
listed above is displayed in hexadecimal numbers. For example, if the peripheral parts of the process
units (K) and developer material (K) reach the maintenance time, the 4-digit hexadecimal number
code will be “0188” in hexadecimal numbers: 0008+0080+0100=0188.
Error Code Downloads Files Discounts Total in database
Parts Catalog Used abbreviations Payments Brands: 14
Service Mode, Compatibility Privacy, Terms, Models: 4531
Troubleshooting Refunds Toshiba: 210