Professional Documents
Culture Documents
Foxboro Evo™ Process Automation System: Product Specifications
Foxboro Evo™ Process Automation System: Product Specifications
Foxboro Evo™ Process Automation System: Product Specifications
Process Automation
System
Product Specifications
PSS 31H-2S233
The FBM233 Redundant Field Device System Integrator (FDSI) module provides an Ethernet interface
between single or dual-ported field I/O devices and the Foxboro Evo™ system.
OVERVIEW
Each FBM233 module has a single 10/100Mbps network connected to the Master. Device output
copper Ethernet connection and a single RJ-45 points, depending on the I/O driver, are written by
connector on the front of the module for connectivity both the Master and Tracker module. Role switching
to dual-ported Ethernet devices. The FBM233 is is automatic if problems are detected (for example,
connected to Ethernet switches or hubs in order to loss of heartbeat from any device) by the I/O driver,
communicate with one external device or up to 64 or the user can switch the roles at any time via
external devices. SMDH. The general network configuration is shown
in Figure 1.
A pair of modules combine to provide redundancy at
the Fieldbus Module (FBM) level. In this configuration,
one FBM233 is the Master, and the other is the
Tracker module. Input points on the control station
are updated from the device inputs received on the
PSS 31H-2S233
Page 2
FEATURES CONFIGURATOR
Key features of the FBM233 are: The FDSI configurator sets up the FBM233 port and
XML based device configuration files. The port
Redundant 10 Mbps or 100 Mbps Ethernet
configurator allows for easy setup of the
network transmission rate to/from field devices
communication parameters for each port (such as,
Communicates with up to 64 field devices Dynamic Host Configuration Protocol (DHCP),
I/O software driver is downloadable from a library IP addresses). The device configurator is not needed
of available protocols for all devices, but when needed it configures device
specific and point specific considerations (such as,
Up to 2000 DCI block connections
scan rate, address of the data to be transferred, and
Integrates field device data into a Foxboro Evo
the amount of data to be transferred in one
control database using Ethernet connectivity
transaction).
Field mounted
Class G3 (harsh) environments.
OPERATIONS
I/O DRIVERS Each FBM233 pair can access up to 64 devices to
read or write data.
This FBM is a generic Ethernet hardware module in
which different software drivers can be loaded. These From the Foxboro Evo control station to which the
drivers configure the FBM to recognize a particular FBM233 is connected (refer to Figure 1), up to 2000
protocol used by the device. Several of these Distributed Control Interface (DCI) data connections
software drivers are a standard product offerings. can be made to read or write data. Supported data
Other custom drivers can be developed to meet types are determined by the particular driver loaded
specific needs. These drivers are dynamically on the FBM233, which converts the data to the DCI
downloaded to the FBM233 with software code data types listed below:
specifically designed to interface with the third party An analog input or output value (integer or IEEE
device’s protocol. single-precision floating point)
The configuration procedures and the software A single digital input or output value
requirements for each driver are unique to the
Multiple (packed) digital input or output values
device(s) being integrated into the system.
(packed in groups of up to 32 digital points per
ETHERNET LINK SETUP connection).
Data communication between the FBM233 and field Thus a Foxboro Evo control station can access up to
devices are through the RJ-45 connector located on 2000 analog I/O values, or up to 64000 digital I/O
the front of the FBM233 module. The RJ-45 values, or a combination of digital and analog values
connector of the FBM233 can be connected through using the FBM233. The frequency of access to the
hubs, or through Ethernet switches to the field FBM233 data by a control station can be as fast as
devices (refer to “ETHERNET SWITCHES FOR USE 500 ms. The performance is dependant on each
WITH FBM233” on page 7). The FBM233 is device type and the layout of data in the device.
connected to Ethernet switches or hubs in order to
communicate with one external device or up to 64
external devices.
PSS 31H-2S233
Page 3
The FBM233 collects the required data from the management functions and operator displays. Data
devices, performs the necessary conversions, and may also be written out to the individual devices from
then stores the converted data in its database for the Foxboro Evo system.
incorporation into the Foxboro Evo plant
Control
Z Z
Processor C C
ZCP270 P P
2 Mbps 2 Mbps
FBM233 FBM233 Module FBM233 FBM233
Module
Fieldbus Fieldbus
See below for typical connections See below for typical connections
100M
COLLISION
1 2 3 4 5 6 7 8 To PC
FULL DUPLEX
To Hub
ACTIVITY
100M 100M 8 PORT ETHERNET SWITCH
COLLISION
LINK
COLLISION
1 2 3 4 5 6 7 8 To PC 1 2 3 4 5 6 7 8
FULL DUPLEX
To PC POWER 1 2 3 4 5 6 7 8
To Hub
FULL DUPLEX
To Hub
X X X X X X X
ACTIVITY ACTIVITY
8 PORT ETHERNET SWITCH 8 PORT ETHERNET SWITCH
LINK LINK
POWER 1 2 3 4 5 6 7 8 POWER 1 2 3 4 5 6 7 8
X X X X X X X X X X X X X X
Ethernet Device
Ethernet Switches
Hubs
DEVICE DEVICE
DEVICE DEVICE
Up To 64 Devices Up To 64 Devices
F U N C T I O N A L S P E C I F I C AT I O N S
F U N C T I O N A L S PE CI F I C AT I O N S ( C O N T I N U E D )
E N V I R O N M E N TA L S P E C I F I C AT I O N S
Operating Storage
TEMPERATURE TEMPERATURE
-20 to +70°C (-4 to +158°F) -40 to +70°C (-40 to +158°F)
RELATIVE HUMIDITY RELATIVE HUMIDITY
5 to 95% (noncondensing) 5 to 95% (noncondensing)
Contamination
Suitable for use in Class G3 (Harsh) environments as
defined in ISA Standard S71.04, based on exposure
testing according to EIA Standard 364-65, Class III.
P H Y S I C A L S P E C I F I C AT I O N S
Mounting
The FBM233 mounts on a Modular Baseplate. The
Part Number
Modular Baseplate can be mounted horizontally or
P0926GX
vertically on a DIN rail, or mounted horizontally in a
19-inch rack using a mounting kit. Refer to Weight
PSS 31H-2SBASPLT for details. 284 g (10 oz) approximate, per module
Dimensions Cables
HEIGHT FROM MODULE TO HUB/SWITCH/DEVICE
102 mm (4 in) 1 m (3.3 ft) up to 100 m (330 ft)
114 mm (4.5 in) including mounting lugs CONNECTORS
WIDTH RJ-45
45 mm (1.75) NULL HUB ADAPTER
DEPTH P0971PK
104 mm (4.11 in)
PSS 31H-2S233
Page 7
DIN Rail Mounted 5-Port 10/100 Base TX Rack and Chassis Mounted Fast Ethernet
Switch Switches
The 5-port 10/100 base TX Ethernet switch For information on the Fast Ethernet switches refer to
(P0972WE) is Din rail mounted and available for use The Foxboro Evo Control Network Ethernet
with the FBM233. You can connect up to four Equipment (PSS 31H-7NW_EQUIP).
Ethernet devices using this 5-port switch.
Additionally, multiple switches can be interconnected
to connect up to 64 devices to a single FBM233.
For detailed physical and electrical specifications,
refer to Model SFNB 5TX 2891001 at
www.phoenixcontact.com/us/products.
10 Mbps (P0972WE)
R E L AT E D P R O DU C T S P E C I F I C AT I O N S H E E T S