Professional Documents
Culture Documents
Vintage Air Vega
Vintage Air Vega
Vintage Air Vega
Facel Vega
Condenser Kit with Drier
FV3B (1957-58)
FV4 (1957-58)
HK (1958-61)
EX (1958)
EX1 (1958-61)
EX2 (1961-65)
061001
18865 Goll St. San Antonio, TX 78266 ph: 210-654-7171 fax: 210-654-3113
2
901112 REV B 4/20/15, INST. FACEL VEGA CONDENSER KIT w/ DRIER PG 2 OF 11
Packing List: Facel Vega
Condenser Kit with Drier (061001)
No. Qty. Part No. Description
4 5 6 7 8 9
2
10 11 12 13 14
3
1
17 18
15 16 20 21
19
22 23 24
3
901112 REV B 4/20/15, INST. FACEL VEGA CONDENSER KIT w/ DRIER PG 3 OF 11
Condenser Orientation
Front View Rear View
#8 Fitting #8 Fitting
#6 Fitting #6 Fitting
4th
Hole
Front Rear
View View
.562 L Nylon
Spacer
Condenser 4
901112 REV B 4/20/15, INST. FACEL VEGA CONDENSER KIT w/ DRIER PG 4 OF 11
Top Mounting Bracket Installation
1. Install top mounting bracket onto condenser using (2) 10-24 x 3/8" pan head screws and (2) 10-24 nuts with
star washers as shown in Figure 2, below. NOTE: Bracket mounts through the 7th and 10th holes from the
left side of the front of condenser.
Condenser Rear
View
Condenser Front
View
Drier Installation
1. Install drier clamps onto drier as shown. Using (2) 10-24 x 1 ¼" pan head screws, (2) nylon spacers and
(2) 10-24 nuts with star washers, install drier onto drier brackets as shown in Figure 3, below.
Drier Bracket
647032
.625 L Nylon
Spacer
Drier Bracket
647032 Drier
Drier Clamps
Condenser
Rear Figure 3
5
901112 REV B 4/20/15, INST. FACEL VEGA CONDENSER KIT w/ DRIER PG 5 OF 11
Bottom
Mounting Bracket Installation
1. Using (4) 10-24 x 3/8" pan head screws with (4) 10-24 nuts with star washers, install the bottom condenser
mounting bracket as shown below.
#6 Fitting
#6 Fitting
6
901112 REV B 4/20/15, INST. FACEL VEGA CONDENSER KIT w/ DRIER PG 6 OF 11
Hardline Installation
1. Lubricate (2) #6 O-rings (See Figure 4, below) and install the #6 drier/condenser hardline as shown below.
Tighten fittings as shown in Figure 4, below.
#6 Drier/Condenser
Hardline
121029
#6 O-ring
#6 O-ring
#6 Fitting
Condenser Front
View
Drier
#8 Fitting
#6 Drier/Condenser
Hardline
121029
Condenser Front
#6 Fitting View
Lubricating O-rings
Male For a proper seal of fittings: Install supplied
Female Nut
O-ring Insert O-rings as shown, and lubricate with supplied
oil.
#6 O-ring
O-ring
Figure 4
O-ring Installs
Supplied Oil Over Male
for O-rings Insert
#8 O-ring #10 O-ring to Swaged Lip
NOTE: Standard torque specifications: Twist With
#6: 11 to 13 ft-lb. This Wrench
#8: 15 to 20 ft-lb. Hold With
#10: 21 to 27 ft-lb. This Wrench
7
901112 REV B 4/20/15, INST. FACEL VEGA CONDENSER KIT w/ DRIER PG 7 OF 11
Hardline Installation (Cont.)
1. Lubricate a #8 O-ring (See Figure 4, Page 7) and install the #8 condenser/compressor hardline as shown below.
Tighten fittings as shown in Figure 4, Page 7.
Condenser Front
View
Condenser Front
View
#6 Fitting
Drier
#8 Fitting
#8 Condenser/Compressor #8 O-ring
Hardline
121032
Condenser Front
View
Condenser Front
Condenser Front View
View
#4 Adel #4 Adel
#10 Sheet Metal #8 Condenser/Compressor #10 Sheet Metal
Clamp Clamp
Screw Hardline Screw
121032
8
901112 REV B 4/20/15, INST. FACEL VEGA CONDENSER KIT w/ DRIER PG 8 OF 11
Condenser Installation
1. Install condenser assembly between the front side of the radiator and the back of the hood latch assembly as
shown below.
2. Secure the top mounting bracket of the condenser to the hood latch assembly using a 5/16-18 x 1" hex
bolt, (2) 5/16" flat washers and a 5/16" nylon locknut as shown below.
3. Secure the bottom passenger side of the condenser mounting bracket to the radiator mount using a
5/16-18 x 1" hex bolt, (2) 5/16" flat washers and a 5/16" nylon locknut as shown below.
4. Secure the bottom driver side of the condenser mounting bracket to the radiator mount using a 5/16-18 x 1"
hex bolt, (2) 5/16" flat washers and a 5/16" nylon locknut as shown below.
Hood Latch
Assembly
Radiator
Front Passenger
Side View 5/16" Flat
5/16-18 x 1" Washer
5/16" Flat Hex Bolt
Washer
5/16" Nylon
Locknut
Radiator
Mount
Radiator
Radiator
Radiator
Rear Passenger Mount
Side View
Bottom Mounting
Bracket
647030
Radiator
5/16-18 x 1"
Hex Bolt
Radiator
Mount
5/16" Flat
Washer 5/16" Nylon
5/16" Flat Locknut
Bottom Mounting Washer
Bracket Driver
647030 Side View
9
901112 REV B 4/20/15, INST. FACEL VEGA CONDENSER KIT w/ DRIER PG 9 OF 11
Hardline
& Trinary Switch Installation
1. Lubricate a #6 O-ring (See Figure 4, Page 7) and install the #6 drier/core hardline as shown below. Tighten
fittings as shown in Figure 4, Page 7.
2. Install trinary switch onto drier as shown below. Wire according to electric fan wiring instructions.
#6 Drier/Core
#6 Drier/Core
Hardline
Hardline
121030
121030
#8 Condenser/Compressor
Hardline Condenser Front
Drier View
121032
Trinary
Switch #6 Condenser/Drier
Hardline
121029
Passenger
Side View
of
Drier Wheel Well
#6 A/C Hose
(Evap./Core)
126001 #6 Drier/Core Hardline
(Included in Hose Kit) 121030 #6 Cond./Drier
Hardline
121029
#10 Evap./Core
Hardline
#10 A/C Hose 121033
(Evap./Core) (Included in
126002 Hose Kit)
(Included in Hose Kit)
Checked By:
Packed By:
Date:
4 5 6 7 8 9
2
10 11 12 13 14
3
1
17 18
15 16 20 21
19
22 23 24