Professional Documents
Culture Documents
B53 3270 Hot Dip Aluminized Coating
B53 3270 Hot Dip Aluminized Coating
B53 3270 Hot Dip Aluminized Coating
Metallic materials
B53 3270
This PSA norm has been translated by RHN / NCF into English using the automatic translation software
Systran (approved by PSA).
The quality of this translation has not been technically validated by the PSA Technical Discipline proprietor
of this norm.
This document is available on-line in "Normes" Intranet (normes.inetpsa.com) as well as on the B2B portal
(suppliers and industrial partners).
If a technical validation of this translation is required, PLEASE request it from RHN / NCF at the address
below:
normespsa@mpsa.com
HISTORY
PARTICIPANTS
The following people took part in the drafting and the checking of this standard:
CONTENTS
2.DOCUMENTARY REFERENCIEL
2.1.1.REFERENCE DOCUMENTS
2.1.2.STANDARDS
Not applicable
2.1.3.REGULATIONS
Not applicable
2.1.4.OTHER DOCUMENTS
Not applicable
2.2.APPLICABLE DOCUMENTS
2.2.1.STANDARDS
B53 3050 STEEL AND ALUMINIUM FLAT PRODUCTS GENERAL SPECIFICATIONS FOR
SUPPLY
B53 3070 FLAT PRODUCTS HOT OR COLD ROLLED SPECIFIC TECHNICAL
REQUIREMENTS
B53 3072 STEEL FLAT PRODUCTS HOT OR COLD ROLLED DIMENSIONAL
SPECIFICATIONS
2.2.2.REGULATIONS
Not applicable
2.2.3.OTHER DOCUMENTS
Not applicable
2.3.EXPRESSIONS ON DOCUMENTS
The matter is indicated in the following forms:
- General Case
When the sheet class is indifferent, to indicate:
• sheet,
• designation of the coating following table of the § Masse.
• index of this standard indicated between brackets,
• thickness.
Example:
Sheet ACE 100 (norm B53 3270) E = 1.5 mm.
- Particular case
When a particular sheet class is necessary for reasons of resistance to fatigue or safety, to indicate:
• sheet,
• designation of the coating following table of the § Masse
• designation of basic sheet (class) according to § Définition of basic sheet.
• index of this standard indicated between brackets,
• thickness.
Example:
Sheet ACE 120-05 (norm B53 3270) E = 1.5 mm.
3.TERMINOLOGY
A dictionary (glossary) of the main terms and their definitions used within the activities of the Department "Amont
Technico-Industriel" can be consulted in-house via the glossary Nectar (http://nectar.inetpsa.com). This glossary is
constantly up-dated.
3.1.DEFINITIONS
Not applicable
3.2.ACRONYMS
Not applicable
4.CHEMICAL COMPOSITION
Not applicable
CLASSIFY C Mn P S If NR DEVELOPMENT
max. max. max. max. max. max.
6.1.2.MECHANICAL CHARACTERISTICS
6.4.2.MASS
It is given in g/m2 double face and is determined by the testing method D25 5075.
The table below gives the masses minimal and maximum guarantees according to the designation of the coating.
Foot-note:
- The aluminum mass can be unequally distributed on the 2 faces of sheet, but to in no case the mass on a face
cannot be lower than 45% of the total mass.
- The measurement thickness can be made as an indication on cut. The use of apparatuses such as the
permascope is on the other hand to proscribe because of presence of a layer of intermetallic compound (Al-Fe)
variable thickness.
6.4.3.ADHERENCE
It is determined by a bending test on 50 mm broad test-tube, by means of a hold of which the thickness is equal to 3
times the thickness of basic sheet.
The test consists in carrying out 2 opposite successive foldings with 180° while following the same li ne of folding.
The test should not cause any chipping or separation of layers of aluminum visible with the naked eye on the
external face of the fold.
6.4.4.ASPECT
Aluminiées sheets the hot uninterrupted always undergo after coating, a very light master key of rolling (skin not).
The purpose of this operation is:
• to give to the product a more regular surface and to improve the aspect of it,
• to temporarily minimize (8 days in classes 01,02,03 and 04 and 6 months for class 05) the risks of vermiculation
during the operation of working.
No serious defect such as run-outs or lacks of matter, even localized is allowed.
6.5.CONDITIONING
The aluminiées sheets can be delivered dry.
However to avoid any beginning of oxidation of aluminum during transport and storage the supplier can deliver the
product:
• that is to say oiled,
• that is to say chromated,
• that is to say chromated oiled.
The type of treatment is specified with the order and must be the subject of an approval.
The thickness of the coating is measured in the little deformed zones not or.
In addition, a control of the state of the coating in the zones particularly requested during working is carried out to
check if its possible degradation is compatible with the quality of desired protection.