Professional Documents
Culture Documents
Es20 292 CJ2 XB24
Es20 292 CJ2 XB24
Series Variations
Bore size [mm] Manufacturable stroke
Series Action Model Cushion
6 10 16 [mm]
Air cylinder
CJ2 series ø6 : 15 to 200
Double acting,
Single rod
CJ2-XB24 V V V Rubber bumper ø10: 15 to 400
ø16: 15 to 400
CJ2-XB24
CAT.ES20-292A
High Durability Series
CJ2-XB24
ø6, ø10, ø16
RoHS
How to Order
y Rod end bracket u Auto switch i Number of auto switches o Auto switch mounting type
Nil None Nil Without auto switch Nil 2 A Rail mounting
V Single knuckle joint ∗ F
or applicable auto switches, S 1 B Band mounting
W Double knuckle joint refer to the table below. n n ∗ F or the rail mounting, screws and nuts
T Rod end cap (Flat type) (E nter the auto switch mounting type (A or for 2 auto switches come with the rail.
U Rod end cap (Round type) B) even when a built-in magnet cylinder ∗ Refer to the Web Catalog for
∗ A
rod end bracket is shipped together without an auto switch is required. auto switch mounting brackets.
with the product, but not assembled. ∗ ø6: Band mounting only
∗ Single/Double knuckle joint: ø10
and ø16 only ∗ Refer to the “Ordering Example of Cylinder Assembly” on page 2.
Applicable Auto Switches / Refer to the Web Catalog for further information on auto switches.
Load voltage Auto switch model Lead wire length [m]
Indicator light
v
——
M9BV M9B M9BV M9B V V V v — v
2-wire 12 V —
Connector — H7C J79C — V — V V V —
3-wire (NPN) M9NWV M9NW M9NWV M9NW V V V v — v
Diagnostic indication 5 V,12 V IC circuit Relay,
Yes 3-wire (PNP) 24 V — M9PWV M9PW M9PWV M9PW V V V v — v
PLC
(2-color indicator)
2-wire 12 V M9BWV M9BW M9BWV M9BW V V V v — v —
Grommet 3-wire (NPN) M9NAV∗1 M9NA∗1 M9NAV∗1 M9NA∗1 v v V v — v
Water resistant 5 V,12 V IC circuit
3-wire (PNP) M9PAV∗1 M9PA∗1 M9PAV∗1 M9PA∗1 v v V v — v
(2-color indicator)
2-wire 12 V M9BAV∗1 M9BA∗1 M9BAV∗1 M9BA∗1 v v V v — v —
With diagnostic output (2-color indicator) 4-wire (NPN) 5 V,12 V — H7NF — F79F V — V v — v IC circuit
3-wire
5V — A96V A96 A96V A96 V — V — — — IC circuit —
Reed auto switch
(NPN equivalent) —
Yes
Grommet — 200 V — — A72 A72H V — V — — —
—
—— 100 V A93V∗2 A93 A93V∗2 A93 V V V V — —
No 100 V or less A90V A90 A90V A90 V — V — — — IC circuit Relay,
2-wire 12 V
Yes 24 V — — C73C A73C — V — V V V — — PLC
Connector
No 24 V or less — C80C A80C — V — V V V — IC circuit
Diagnostic indication (2-color indicator) Grommet Yes — — — — A79W — V — V — — — —
∗1 W
ater-resistant type auto switches can be mounted on the models, but SMC cannot guarantee water resistance.
Please contact SMC regarding water-resistant types with the above model numbers.
∗2 The 1 m lead wire is only applicable to the D-A93.
∗ Lead wire length symbols: 0.5 m·················· Nil (Example) M9NW 5 m·················· Z (Example) M9NWZ
1 m·················· M (Example) M9NWM None··············· N (Example) H7CN
3 m·················· L (Example) M9NWL
∗ Since there are applicable auto switches other than those listed above, refer to the Web Catalog for details.
∗ Solid state auto switches marked with a “v” are produced upon receipt of order
∗ The D-A9l/M9l/A7l/A80l/F7l/J7l auto switches are shipped together, but not assembled. (For the band mounting, only the auto switch mounting brackets are assembled before shipment.)
1
High Durability Series
Longer Life Cylinder
Double Acting, Single Rod CJ2-XB24
Specifications
Auto switch
Band mounting The mounting pitch and shape of this product Moisture Control
with auto switch are the same as those of the Tube
Mounting D: Double clevis Air Cylinder CJ2 series with auto switch. IDK Series
Pivot bracket N: Yes For details, refer to the Web Catalog.
When operating an actuator with a small bore
Rod end bracket W: Double knuckle joint size and a short stroke at a high frequency, dew
· A uto Switch Proper Mounting Position
Auto switch D-M9BW: 2 pcs. condensation (water droplets) may occur inside
Auto switch mounting B: Band mounting (Detection at stroke end) and Mounting Height
the piping depending on the conditions.
· Min. Stroke for Auto Switch Mounting Simply connecting the moisture control tube to
∗ Pivot brackets, double knuckle joints, and auto switches · Operating Range the actuator will prevent dew condensation from
are shipped together with the product, but not assembled. · Auto Switch Mounting Brackets/Part Nos. occurring. For details, refer to the Web Catalog.
* Except ø6
The operating speed, allowable loads at the rod end, theoretical output, weight, and accessory
are equivalent to those of the Air Cylinder CJ2 series. For details, refer to the Web Catalog.
2
High Durability Series
CJ2-XB24
Dimensions
Basic (B)
ø6
Rod end nut Mounting nut
øNDh8
MM NN GA Piping port 2 x M5 x 0.8 GB
øC
øD
B–0.3
0
A F T NA NB
0
B–0.3 H S + Stroke
Z + Stroke
8–0.3
0
NC
0
SA + Stroke 8–0.3
ZA + Stroke
ø10, ø16
øNDh8
0
B –0.3 A F NA NB
H S + Stroke
Z + Stroke
3
High Durability Series
Longer Life Cylinder
Double Acting, Single Rod CJ2-XB24
Dimensions
Single foot bracket (L)
ø6
Mounting nut Piping port 2 x M5 x 0.8
Cover surface Rod end nut NN F GA GB
MM øC
øD
B–0.3
0
LY
LB
LH
0
LX LT B–0.3
X Y
LZ
A T NA NB
H S + Stroke
2 x øLC
Z + Stroke
Mounting hole
8–0.3
0
0
NC 8–0.3
SA + Stroke
ZA + Stroke
ø10, ø16
Mounting nut
F GA Piping port 2 x M5 x 0.8 GB
Cover surface Rod end nut NN
MM
øC
øD
B–0.3
0
LY
LB
LH
0
B–0.3
LT
LX
LZ A
X Y NA NB
H S + Stroke
2 x øLC Z + Stroke
Mounting hole
Piping port M5 x 0.8
4
High Durability Series
CJ2-XB24
Dimensions
Double foot bracket (M)
ø6
H
Mounting nut Mounting nut
Rod end nut Piping port 2 x M5 x 0.8 NN
Cover surface MM NN F GA GB F
øD
LY
LB
LH
LX
LT
LT
LZ A T NA NB Y X
X Y S + Stroke
4 x øLC LS + Stroke
Mounting hole Z + Stroke
ø10, ø16
H Mounting nut
Mounting nut F GA Piping port 2 x M5 x 0.8 GB F NN
Cover surface
Rod end nut NN
MM
øD
LY
LB
LT
LH
LT
LX
LZ A
4 x øLC
Mounting hole X Y NA NB Y X
S + Stroke
LS + Stroke
Z + Stroke
5
High Durability Series
Longer Life Cylinder
Double Acting, Single Rod CJ2-XB24
Dimensions
Rod flange (F)
ø6
Mounting nut Piping port 2 x M5 x 0.8
Cover surface Rod end nut NN GA GB
MM øC
øD
B–0.3
FY
FB
0
FX 2 x øFC FT T
0
FZ Mounting hole A F NA NB B–0.3
H S + Stroke
Z + Stroke
8–0.3
0
0
NC 8–0.3
SA + Stroke
ZA + Stroke
ø10, ø16
Mounting nut
Cover surface NN GA Piping port 2 x M5 x 0.8 GB
Rod end nut
MM øC
øD
B–0.3
FY
FB
FX FT 0
B–0.3
FZ A F NA NB
2 x øFC
Mounting hole H S + Stroke
Z + Stroke
6
High Durability Series
CJ2-XB24
Dimensions
Head flange (G)
ø6
FY
FB
0
F
0
B–0.3 A T NA NB FT
H S + Stroke F FX 2 x øFC
FZ Mounting hole
Z + Stroke
ø10, ø16
Rod end nut GA Piping port 2 x M5 x 0.8 GB Mounting nut Cover surface
NN NN
øC
MM
øD
B–0.3
FY
FB
0
B–0.3
0
A F NA NB FT FX 2 x øFC
Mounting hole
H S + Stroke F FZ
Z + Stroke
7
High Durability Series
Longer Life Cylinder
Double Acting, Single Rod CJ2-XB24
Dimensions
Double clevis (D)
ø10, ø16
+0.030
øCDH9 0
–0.030
Rod end nut GA Piping port 2 x M5 x 0.8 NB Clevis pin (øcdd9 –0.060)
MM GB
øC øC
øD
CZ–0.3
B–0.3
0
0
+0.2
0 A NA CX +0.1
B–0.3
H S + Stroke U 0
CZ–0.3
Z + Stroke R
ZZ + Stroke
8
High Durability Series
CJ2-XB24
Dimensions
Double-side bossed (E)
ø6
øNDh8
Mounting nut
Piping port 2 x M5 x 0.8 YY
NN
øNDh8
Rod end nut
GB NN
MM
øC
øD
B–0.3
0
NA
0
B–0.3 A F T NB
H S + Stroke F Section YY detail
Z + Stroke
ø10, ø16
øNDh8
Mounting nut
Section Y detail
øNDh8
NN Y GA Piping port 2 x M5 x 0.8 GB YY
Rod end nut
MM NN
øC
B–0.3
0
0
B–0.3 A F NA NB
øD
Section YY detail
H S + Stroke F
Z + Stroke
9
High Durability Series
CJ2-XB24
Specific Product Precautions
Be sure to read this before handling the products. Refer to the back cover for safety instructions. For actuator
and auto switch precautions, refer to the “Handling Precautions for SMC Products,” the “Operation Manual,”
and air cylinder CJ2 series specific product precautions on the SMC website: https://www.smcworld.com
Handling
Warning Caution
1. Use within the specified cylinder speed and kinetic 1. T
ighten retaining screws to an appropriate tightening
energy ranges. torque within the range given below.
Otherwise, cylinder and seal damage may occur. ø6: 2.1 to 2.5 N·m, ø10: 5.9 to 6.4 N·m
2. Do not apply excessive lateral load to the piston ø16: 10.8 to 11.8 N·m
rod. 2. To remove and install retaining rings for knuckle
Easy checking method pins or clevis pins, use an appropriate pair of pliers
Min. operating pressure after the cylinder is mounted to the (tool for installing a type C retaining ring). In
equipment (MPa) = Min. operating pressure of cylinder (MPa) particular, use a pair of ultramini pliers for removing
+ {Load mass (kg) x Friction coefficient of guide/Sectional area and installing retaining rings on the ø10 cylinder.
of cylinder (mm2)} 3. For the auto switch rail mounting type, do not remove
If smooth operation is confirmed within the above value, the the rail that is mounted.
load on the cylinder is the resistance of the thrust only and it Because retaining screws extend into the cylinder,
can be judged as having no lateral load. this could lead to an air leak.
3. Do not apply any torque to the cover joint. 4. Please contact SMC when the stroke exceeds 100
Both the rod cover and head cover have wrench flats. When mm for the axial foot mounting type.
mounting the product, be sure to tighten with an appropriate
amount of force.
Durability of The Cylinder
When mounting the cylinder or installing a fitting to the port,
perform tightening while holding the cover on the same side as The durability of a longer life cylinder has been evaluated
the component being installed with a wrench. by comparison with the existing cylinders under SMC’s
Do not hold the cover on the opposite side. Failure to follow test conditions.
this instruction may cause the cover and tube joint to be The durability of a cylinder depends on the customer’s
broken by torque. operating conditions and operating environment.
Therefore, durability of four times or longer will not be
guaranteed under all conditions.
10
These safety instructions are intended to prevent hazardous situations and/or
Safety Instructions equipment damage. These instructions indicate the level of potential hazard with
the labels of “Caution,” “Warning” or “Danger.” They are all important notes for
safety and must be followed in addition to International Standards (ISO/IEC)∗1),
and other safety regulations.
∗1) ISO 4414: Pneumatic fluid power – General rules relating to systems.
Caution indicates a hazard with a low level of risk which,
Caution: if not avoided, could result in minor or moderate injury.
ISO 4413: Hydraulic fluid power – General rules relating to systems.
IEC 60204-1: Safety of machinery – Electrical equipment of machines.
(Part 1: General requirements)
Warning indicates a hazard with a medium level of risk which,
Warning: if not avoided, could result in death or serious injury.
ISO 10218-1: Manipulating industrial robots – Safety.
etc.
Danger indicates a hazard with a high level of risk which,
Danger : if not avoided, will result in death or serious injury.
Warning Caution
1. The compatibility of the product is the responsibility of the 1. The product is provided for use in manufacturing industries.
person who designs the equipment or decides its The product herein described is basically provided for peaceful use in
specifications. manufacturing industries.
Since the product specified here is used under various operating conditions, If considering using the product in other industries, consult SMC beforehand
its compatibility with specific equipment must be decided by the person who and exchange specifications or a contract if necessary.
designs the equipment or decides its specifications based on necessary If anything is unclear, contact your nearest sales branch.
analysis and test results. The expected performance and safety assurance
of the equipment will be the responsibility of the person who has determined Limited warranty and Disclaimer/
its compatibility with the product. This person should also continuously
review all specifications of the product referring to its latest catalog Compliance Requirements
information, with a view to giving due consideration to any possibility of The product used is subject to the following “Limited warranty and Disclaimer” and
equipment failure when configuring the equipment. “Compliance Requirements”.
Read and accept them before using the product.
2. Only personnel with appropriate training should operate
machinery and equipment. Limited warranty and Disclaimer
The product specified here may become unsafe if handled incorrectly. The
assembly, operation and maintenance of machines or equipment including
1. The warranty period of the product is 1 year in service or 1.5 years after
our products must be performed by an operator who is appropriately trained
the product is delivered, whichever is first.∗2)
and experienced. Also, the product may have specified durability, running distance or
replacement parts. Please consult your nearest sales branch.
3. Do not service or attempt to remove product and machinery/ 2. For any failure or damage reported within the warranty period which is clearly our
equipment until safety is confirmed. responsibility, a replacement product or necessary parts will be provided.
1. The inspection and maintenance of machinery/equipment should only be This limited warranty applies only to our product independently, and not to any
performed after measures to prevent falling or runaway of the driven other damage incurred due to the failure of the product.
objects have been confirmed.
3. Prior to using SMC products, please read and understand the warranty terms
2. When the product is to be removed, confirm that the safety measures as and disclaimers noted in the specified catalog for the particular products.
mentioned above are implemented and the power from any appropriate
∗2) Vacuum pads are excluded from this 1 year warranty.
source is cut, and read and understand the specific product precautions
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
of all relevant products carefully. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad
3. Before machinery/equipment is restarted, take measures to prevent or failure due to the deterioration of rubber material are not covered by the limited warranty.
unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of
Compliance Requirements
safety measures if the product is to be used in any of the 1. The use of SMC products with production equipment for the manufacture of
following conditions. weapons of mass destruction (WMD) or any other weapon is strictly prohibited.
1. Conditions and environments outside of the given specifications, or use 2. The exports of SMC products or technology from one country to another are
outdoors or in a place exposed to direct sunlight. governed by the relevant security laws and regulations of the countries involved
2. Installation on equipment in conjunction with atomic energy, railways, air in the transaction. Prior to the shipment of a SMC product to another country,
navigation, space, shipping, vehicles, military, medical treatment, assure that all local rules governing that export are known and followed.
combustion and recreation, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press
applications, safety equipment or other applications unsuitable for the Caution
standard specifications described in the product catalog.
SMC products are not intended for use as instruments for legal
3. An application which could have negative effects on people, property, or metrology.
animals requiring special safety analysis. Measurement instruments that SMC manufactures or sells have not been
4. Use in an interlock circuit, which requires the provision of double interlock qualified by type approval tests relevant to the metrology (measurement) laws
for possible failure by using a mechanical protective function, and of each country. Therefore, SMC products cannot be used for business or
periodical checks to confirm proper operation. certification ordained by the metrology (measurement) laws of each country.
Safety Instructions Be sure to read the “Handling Precautions for SMC Products” (M-E03-3) and “Operation Manual” before use.