Professional Documents
Culture Documents
At @ @auf @auf : Stop - Ec - Ec ZUF ZUF Eo Eo
At @ @auf @auf : Stop - Ec - Ec ZUF ZUF Eo Eo
At @ @auf @auf : Stop - Ec - Ec ZUF ZUF Eo Eo
F.xxx Fatal error. The door drive no longer operates. STOP Stop
Cover buttons flash quickly.
_Ec_ CLOSE limit position
E.xxx Minor error. The door drive now only operates
in dead-man mode (possibly dependent upon
direction). Cover buttons flash slowly. ≡Ec≡ CLOSE limit position locked electrically
x.xxx. Active error. When this has been corrected, it �Eo� OPEN limit position
must be acknowledged by pressing and holding
the rotary-push button. ≡Eo≡ OPEN limit position locked electrically
x.xxx Active error. When this has been corrected, it Opening active
@AUF
does not have to be acknowledged
@AUF Opening active (flashes)
xxxx. Corrected error. It must be acknowledged
F.000 Door position outside movement range �E1� Partial opening position reached
F.185 Confirmation after restart of the control unit Smoke/heat ventilation (RWA) intermediate
≡rA≡
F.211 NA1 EMERGENCY STOP triggered stop position locked electrically
F.212 NA2 EMERGENCY STOP triggered ≡E1≡ Partial opening position locked electrically
F.214 Wicket door open
≡SE≡ Safety edge activated
F.216 Door lock bolt does not unlock
≡Lb≡ Light barrier activated
F.217 Wicket door lock bolt does not unlock
F.330 Slack rope/overload switch triggered
≡S1≡ Pull-in safety device activated
F.336 Negative result for electromagnetic test of ≡S2≡ Pull-in safety device activated
wicket door switch
≡S3≡ Pull-in safety device activated
F.700 OPEN and CLOSE limit switches simultaneously
engaged NOTF Emergency operation
F.701 Partial opening and close limit switches simulta- Hd.cL Closing in dead-man mode (membrane but-
neously engaged ton: CLOSE)
F.750 Absolute value encoder protocol error in Hd.oP Opening in dead-man mode (membrane but-
transmission ton: OPEN)
F.752 Error in transmission to the drive’s absolute Hd.Ec CLOSE limit position reached
value encoder
Hd.Eo OPEN limit position reached
F.850 Collective input fault
‘Hd’ Manual
F.922 Emergency stop transistor defective
HD.ru Inching mode
F.927 Hardware testing of the open, close or safety
transistors failed E.I.C.H. Safety edge (SKS) functional test (in dead-
man mode) possible, the direction of rotation
F.931 Internal control unit error during ROM test is set, automatic switch after travelling a short
F.932 Internal control unit error during RAM test distance in calibration of CLOSE limit position
E.374 Safety edge testing pre-limit switch set too high 920 Error history
Information messages
I.043 Fault in the pre-limit switch for the light barrier
I.081 Maintenance interval has elapsed
I.111 Wireless push-button channel 1 engaged for
too long
I.112 Wireless push-button channel 2 engaged for
too long
I.113 Wireless push-button channel 3 engaged for
too long
I.114 Wireless push-button channel 4 engaged for
too long
I.116 Travel command "Close" engaged for too long
I.118 Travel command sequence button engaged for
too long
I.119 Travel command sequence button engaged for
too long
I.220 RWA input triggered
I.351 Safety edge SE1 has triggered on 5 consecu-
tive closing movements
I.361 Safety edge SE2 has triggered on 5 consecu-
tive closing movements
I.852 Collective input fault
I.905 Keypad on cover is not attached properly
en Information sheet for BDC-E800R/S
Position of the terminals and complete connecting diagram: P991: 3
Drive
3~230 V
3~230 V
3~400 V 3~230 V
3 2 1 8 7 9 6 1011 4 5
RADIO
PLUG-IN MODULE
X4
ON
EMERGENCY STOP
Light barrier
1 AT
Power output
24 V DC max. 0.5 A
X3
X1
12
3 2 1 7 6 8 5 11 9 4 10
RADIO
PLUG-IN MODULE
X4
ON
EMERGENCY STOP
Light barrier
1 AT
Power output
24 V DC max. 0.5 A
X3
X1