Professional Documents
Culture Documents
E.1.8.1-COC-2-7.8 Inch (75 Jts DP)
E.1.8.1-COC-2-7.8 Inch (75 Jts DP)
ZK-7.6-28 REV0
Item# Title
1 Drill Pipe Performance Characteristics Sheet
2 Certificate of Compliance
13 Serialization Log
14 Export Classification
Drill Pipe Performance Sheet
2/9/2017
Bbls/ft - Elevator capacity is less than new tube tensile. Consider increasing tool joint OD.
0.0041
Warnings:
* With no axial load or bending in string ** Best estimate with coating - Connection tensile at Maximum MUT is less than prem pipe body tensile, a lower MUT should be considered.
Note: Oil field barrel equivalent to 42 US gal Note: Nominal burst calculated at 87.5% RBW per API - Tool Joint ID is too large, making pin connection weaker in tension.
The Technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be consider as a
recommendation. The user is fully responsible for the accuracy and suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the
results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall
thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only
and does not represent or imply acceptable operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings,
acceptable use of the product, maintain safe operating practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin
and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated 3.179 46200 39500
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions 3.213 65000 58300
(remaining body wall) is for information only and does not represent or imply acceptable operating limits. It is the responsibility of the customer and the end user
3.246 83500 76800
to determine the appropriate performance ratings, acceptable use of the product, maintain safe operating practices, and to apply a prudent safety factor suitable
for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the drilling manual, it is
3.279 102100 95400
recommended that drilling torque should not exceed 80% of MUT. 3.3125 121200 114500
This hereby certifies that NOV Grant Prideco has met or exceeded the manufacturing and
qualityrequirements of the above referenced specification(s) in Manufacturing the following
below describedmaterial for:
TRINIDAD DRILLING LP
NOV GP Order Confirmation Number: 1000128660
75 Joints 2371.85 FT
2018-12-12
NOV GP Order Confirmation Number: 1000128660 Customer Purchase Order Number: KUW00010
Description: (75) 2.875"OD 0.362" WT 10.4LB./FT. IU R2 CYX105-120 DRILL PIPE WITH HT2-7/8PAC PIN 3-1/8"OD×1-
1/2"ID & 9" PIN OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-7/8PAC PIN
AND HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID & 14"BOX OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000
HARDBANDING FOR HT2-7/8PAC BOX.TK34 INTERNAL COATING
Certificate of Make and Break
This hereby certifies that the Make and Break Operation has been performed on the
following:
HT2-7/8PAC PIN 3-1/8"OD×1-1/2"ID & 9" TONG SPACE WITH TCS 8000 3/32"RAISED
1-1/2"WIDTH HARDBANDING & WITH H-SERIES BENCHMARK
HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID & 14" TONG SPACE WITH TCS 8000
3/32"RAISED 3"WIDTH HARDBANDING & WITH H-SERIES BENCHMARK
in strict compliance with the Applicable Nov Grant Prideco Standard Operating Procedure
No.GPJ-MB-1 Rev.4 for the Make and Break Operation, Latest Revision and Customer's
Requirements. The issuance of this certificate indicates that the Make and Break Operation
was completed.
2018-12-12
NOV GP Order Confirmation Number: 1000128660 Customer Purchase Order Number: KUW00010
Description: (75) 2.875"OD 0.362" WT 10.4LB./FT. IU R2 CYX105-120 DRILL PIPE WITH HT2-7/8PAC PIN 3-1/8"OD×1-
1/2"ID & 9" PIN OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-7/8PAC PIN
AND HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID & 14"BOX OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000
HARDBANDING FOR HT2-7/8PAC BOX.TK34 INTERNAL COATING
Certificate of Hardbanding Inspection
in strict compliance with the Applicable Grant Prideco/GPJ Operating Procedure for the
Hardband Operation,Latest Revision and Customer's Requirements.The issuance of this
certificate indicates that the Hardband Operation was completed.
2018-12-12
NOV GP Order Confirmation Number: 1000128660 Customer Purchase Order Number: KUW00010
Description: (75) 2.875"OD 0.362" WT 10.4LB./FT. IU R2 CYX105-120 DRILL PIPE WITH HT2-7/8PAC PIN 3-1/8"OD×1-
1/2"ID & 9" PIN OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-7/8PAC PIN
AND HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID & 14"BOX OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000
HARDBANDING FOR HT2-7/8PAC BOX.TK34 INTERNAL COATING
TGP
Certificate of Inspection 检验报告
Customer: GPJ
顾客
P.O. #: TGP.CN2018066
订单号
Product: X Drill Pipe Body Tubing
产品
PIPE SIZE PIPE WEIGHT NOMINAL WALL GRADE RANGE UPSET TYPE
规格 重量 壁厚 钢级 长度范围 加厚形式
2.875" 10.40 0.362 CYX105-120 R2 IU
2018-11-8
TGP
Certificate of Inspection 检验报告
Customer: GPJ
顾客
P.O. #: TGP.CN2018047
订单号
Product: X Drill Pipe Body Tubing
产品
PIPE SIZE PIPE WEIGHT NOMINAL WALL GRADE RANGE UPSET TYPE
规格 重量 壁厚 钢级 长度范围 加厚形式
2.875" 10.40 0.362 CYX105-120 R2 IU
2018-9-3
NOV Grant Prideco
Drilling Products & Services
Product Management Dept.
400 North Sam Houston Pkwy, East Suite 900
Houston, TX 77060
United States of America
+1 (281) 878-8000 main
+1 (281) 878-5736 fax
www.NOV.com
www.grantprideco.com
Bulletin
Approval
PC-7.5-2009Feb11-EXT
Designation:
Rev.
5 Approval Date: Oct 17, 2007
Number:
Authored
NOV Grant Prideco Distribution Date: Oct 17, 2007
By:
2. Equipment: The equipment listed below shall be required to perform these inspections.
3. Preparation: All thread and make-up shoulder surfaces shall be cleaned sufficiently to
allow for visual inspection.
4. Visual inspection:
4.1. Primary Shoulder (Seal): Refer to the “HT Connection Section” in the “NOV Grant
Prideco Rotary Shoulder Handbook” or the “HT Connection Field Inspection
Dimension” drawing for terminology and shoulder locations. The seal surface
Page 1 PC-7.5-2009Feb11-EXT
should be free of galls, nicks, washes, fins, or other conditions that would
adversely affect its stability or pressure holding capacity.
4.1.1. Damage that does not exceed 1/32” in depth and crosses less than 30% of the
radial width of the seal is acceptable. If the damage exceeds these limits,
refacing shall be used to repair the seal surface.
4.1.2. The refacing repair should only remove enough material to repair the damage. A
maximum of 1/32” of material may be remove during each refacing operation and a
maximum of 1/16” may be removed from the connection before re-threading is required.
After refacing repair, a minimum length of 1/16” (.062”) shall remain on the box
refacing benchmark, and 3/16” maximum (.188”) shall remain on the pin refacing
benchmark. See sketch.
New Pin Pin Max Reface New Box Box Max Reface
4.2. Secondary Shoulder (Mechanical Stop): The Secondary Shoulder is not a sealing
surface. Damage to this surface is not critical unless the damage interferes with the
make-up, driftability, or torque capacity of the connection. Dents, scratches, and cuts
do not affect this surface unless these exceed 1” in width and cause the connection to
be rejected due to shortening of the shoulder-to-shoulder length. Filing may be used
to repair material protrusions, which extend from the face. Connection length readings
shall not be taken in damaged areas.
4.3. Threads: Thread flank surfaces should be free of damage that exceeds 1/16” in
depth or 1/8” in diameter. Thread roots should be free of damage that extends below
the radius. Thread crest should be free of damage that would interfere with make-up.
Material that protrudes beyond the thread profile should be removed using a round
cornered triangle hand file or soft buffing wheel.
4.4. Profile: The thread profile shall be verified along the full length of complete threads in
two locations at least 90° apart. The profile gage should mesh evenly in the threads
and show normal contact. If the profile gage does not mesh in the threads, lead
measurements shall be taken.
4.5. Coating: Threads and shoulders that are repaired by filing or refacing must be
phosphate coated or by using copper sulfate.
Page 2 of 4 PC-7.5-2009Feb11-EXT
5. Dimensional Inspection:
5.1. Lead: The thread lead should be verified, if the profile gage indicates that thread
stretch has occurred. The thread lead shall be measured over a 2” interval and shall
not exceed 0.006”. Connections failing this inspection should be inspected for cracks
and, if none are found, re-threaded.
5.2. Box Outside Diameter: The outside diameter of the box shall be measured at a
distance of 2” +/-1/4” from the primary make-up shoulder. Measurements shall be
taken around the circumference to determine the minimum diameter. This dimension
shall be compared to the minimum diameter for the connection being inspected to
determine acceptance or rejection.
5.3. Box Counterbore Diameter: The inside diameter of the box counterbore shall be
verified. This dimension is not used to determine acceptance or rejection, but to test
for box swell and the need to verify connection length.
5.4. Box Counterbore Wall Thickness: The wall thickness between the “Box Outside
Diameter” and “Box Counterbore Diameter” shall be measured to insure that it
exceeds the minimum dimension for the connection being inspected.
5.5. Box Connection Length: The distance between the primary and secondary make-
up shoulders shall be verified in two locations 180° apart. This distance shall be
compared to requirement for the connection being inspected to determine
acceptance or rejection.
5.5.1. If the connection length exceeds the specified dimension, repair may be
made by refacing the primary make-up shoulder.
5.5.2. If the connection length is less than the specified dimension, refacing the
secondary make-up shoulder may be adequate to repair this condition.
5.5.3. Refacing limits are the same as for repair of damaged shoulders.
5.6. Pin Nose Diameter: The outside diameter of the pin nose shall be verified. This
dimension is not used to determine acceptance or rejection, but to test for pin nose
swell and the need to verify connection length.
5.7. Pin Connection Length: The distance between the primary and secondary makeup
shoulders shall be verified in two locations 180° apart. This distance shall be
compared to requirement for the connection being inspected to determine acceptance
or rejection.
5.7.1. If the connection length exceeds the specified dimension, repair may be
made by refacing the secondary make-up shoulder (pin nose).
5.7.2. If the connection length is less than the specified dimension, refacing the
Page 3 of 4 PC-7.5-2009Feb11-EXT
primary make-up shoulder may be adequate to repair this condition.
5.7.3. Refacing limits are the same as for repair of damaged shoulders.
5.8. Tong Length: a minimum tong space requirement of 6" for pins and a minimum box
tong space equal to the connection length +1" or 8" minimum, whichever is greater.
6. Re-threading: This method shall be used to repair connections that fail to meet the
requirements stipulated in this inspection procedure after field repair is completed.
Performance of this operation may not require complete removal of the thread profile if
sufficient material can be removed to comply with the new product requirements. (The
connection does not have to be “reblanked”, however all torque shoulders, seal surfaces, and
thread elements must be machined to 100% “bright metal”. This is not necessary for
cylindrical diameters). After completion the connection must be phosphate coated. (Copper
Sulfate is not an acceptable substitute for phosphate for “re-threaded” connections.)
Page 4 of 4 PC-7.5-2009Feb11-EXT
管体检验证明书
Certificate of Testing for Drill Pipe body
Mill Chemistry (%)L:熔炼成分 P:成品成分
Mill钢厂 Type类型 Heat No.炉号 C Si Mn P S Ni Cr Mo Cu Al B V
TPCO L 083664 0.28 0.28 0.48 0.009 0.002 0.02 1.05 0.44 0.04 0.031 0.0015 0.04
TPCO P 083664 0.28 0.27 0.48 0.007 0.001 0.03 1.05 0.48 0.05 0.028 0.0006 0.05
TPCO P 083664 0.28 0.27 0.48 0.006 0.001 0.03 1.07 0.48 0.05 0.029 0.0008 0.05
Grain Size:9.0
Inclusions:OK
Tube 管体19P 10*7.5 21 083664 362 168 166 166 167 100
Tube 管体19P 10*7.5 21 083664 363 152 146 148 149 100
Pos No.件号 ID MD OD ID MD OD ID MD OD ID MD OD
Tube 管体19P 24.0 24.5 25.0 24.5 25.0 25.0 24.5 25.0 25.0 24.0 24.5 25.0
Tube 管体19P 22.5 23.0 23.5 23.5 23.0 24.5 23.5 23.5 23.0 24.5 22.5 23.0
2018-11-8
客户:
GPJ
Customer:
客户采购订单号码:
TGP.CN2018066
Customer Purchase Order Number:
产品描述: 2.875" 10.4# 0.362" WT H-SERIES RANGE 2 SMLS DRILL PIPE QUENCHED AND TEMPERED TO GRADE
Description: CYX105-120
管体检验证明书
Certificate of Testing for Drill Pipe body
Mill Chemistry (%)L:熔炼成分 P:成品成分
Mill钢厂 Type类型 Heat No.炉号 C Si Mn P S Ni Cr Mo Cu Al B V
TPCO L 282492 0.28 0.28 0.48 0.009 0.002 0.02 1.05 0.44 0.04 0.031 0.0015 0.04
TPCO P 282492 0.28 0.26 0.48 0.007 0.001 0.03 1.06 0.48 0.05 0.029 0.0007 0.05
TPCO P 282492 0.28 0.27 0.48 0.006 0.001 0.03 1.06 0.48 0.05 0.028 0.0007 0.05
Inclusions:OK
Tube 管体19P 10*7.5 21 282492 363 152 146 148 149 100
Pos No.件号 ID MD OD ID MD OD ID MD OD ID MD OD
Tube 管体19P 22.5 23.0 23.5 23.5 23.0 24.5 23.5 23.5 23.0 24.5 22.5 23.0
2018-9-3
客户:
GPJ
Customer:
客户采购订单号码:
TGP.CN2018047
Customer Purchase Order Number:
产品描述: 2.875" 10.4# 0.362" WT H-SERIES RANGE 2 SMLS DRILL PIPE QUENCHED AND TEMPERED TO GRADE
Description: CYX105-120
Certificate of Testing for Pin
Mill Chemistry (%)化学成分
制造商Mill Heat No. C SI MN P S CR NI MO CU TI NB CA N H(ppm)
JSD 18702461 0.3600 0.2400 0.9300 0.0100 0.0020 1.0800 0.0300 0.3000 0.0500 0.0050 0.0100 0.0001 0.0041 0.7000
0.35-0.38 0.15-0.35 0.85-1.00 0.015 MAX 0.008 MAX 0.90-1.20 0.25 MAX 0.28-0.33 0.25 MAX 0.005-0.015 0.01-0.02 0.005 MAX 0.009 MAX 2ppm MAX
API Location
Position Size Heat No. Heat Code Tensile KSI YieldKSI Elong % RA% OD BHN
BHN
18DC00155 0.500" 18702461 T183591 152.830 138.910 19.00 63.00 300 323
13.0%MI 293-331
≥140ksi 120-165ksi 35.0%MIN 285-331HBW
N HBW
HT2-7/8PAC PIN 3-1/8"OD×1-1/2"ID & 9" TONG SPACE WITH TCS 8000 3/32"RAISED 1-1/2"WIDTH HARDBANDING & WITH H-SERIES BENCHMARK
All properties meet the requirements of the Customer Purchuse Order, API Specification 5DP Latest Edition and GPJ Specification GPJ902 R3.I
certify that these tests were conducted in according with applicable specification and that the data contained herein is true and correct.
2018-12-12
NOV GP Order Confirmation Number: 1000128660 Customer Purchase Order Number: KUW00010
Description: (75) 2.875"OD 0.362" WT 10.4LB./FT. IU R2 CYX105-120 DRILL PIPE WITH HT2-7/8PAC PIN 3-1/8"OD×
1-1/2"ID & 9" PIN OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-
7/8PAC PIN AND HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID & 14"BOX OD LENGTH & H-SERIES
BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-7/8PAC BOX.TK34 INTERNAL COATING
Certificate of Testing for Box
Mill Chemistry (%)化学成分
Mill Heat No. C SI MN P S CR NI MO CU TI NB CA N H(ppm)
JSD 18702461 0.3600 0.2400 0.9300 0.0100 0.0020 1.0800 0.0300 0.3000 0.0500 0.0050 0.0100 0.0001 0.00410 0.7000
0.35-0.38 0.15-0.35 0.85-1.00 0.015 MAX 0.008 MAX 0.90-1.20 0.25 MAX 0.28-0.33 0.25 MAX 0.005-0.015 0.01-0.02 0.005 MAX 0.009 MAX 2ppm MAX
18DD03000 0.500" 18702461 T183677 157.760 143.695 17.00 60.00 331 331
13.0%MI 293-331
≥140ksi 120-165ksi 35.0%MIN 285-331HBW
N HBW
HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID & 14" TONG SPACE WITH TCS 8000 3/32"RAISED 3"WIDTH HARDBANDING & WITH H-SERIES BENCHMARK
All properties meet the requirements of the Customer Purchuse Order, API Specification 5DP Latest Edition and GPJ Specification GPJ902 R4.I certify
that these tests were conducted in according with applicable specification and that the data contained herein is true and correct.
2018-12-12
NOV GP Order Confirmation Number: 1000128660 Customer Purchase Order Number: KUW00010
Description: (75) 2.875"OD 0.362" WT 10.4LB./FT. IU R2 CYX105-120 DRILL PIPE WITH HT2-7/8PAC PIN 3-1/8"OD
×1-1/2"ID & 9" PIN OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-
7/8PAC PIN AND HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID & 14"BOX OD LENGTH & H-SERIES
BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-7/8PAC BOX.TK34 INTERNAL COATING
Certificate of Testing for Weld Area
Mechanical Test Data
Specimen Position Size Tensile KSI Yield KSI Elong% RA% Remark
Weld-box 18-224-01 0.5" 125.598 112.980 17.00 70.00
75
All properties meet the requirements of the customer purchase order and GPJ900 for Weld Area, I certify that these tests were conducted in
accordance with applicable specifications and that the data contained herein is true and correct.
2018-12-12
NOV Grant Prideco Representative Date
Customer: TRINIDAD DRILLING LP Date: 2018-12-12
NOV GP Order Confirmation Number: 1000128660 Customer Purchase Order Number: KUW00010
Description: (75) 2.875"OD 0.362" WT 10.4LB./FT. IU R2 CYX105-120 DRILL PIPE WITH HT2-7/8PAC PIN 3-1/8"OD×
1-1/2"ID & 9" PIN OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-
7/8PAC PIN AND HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID & 14"BOX OD LENGTH & H-SERIES
BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-7/8PAC BOX.TK34 INTERNAL COATING
Certificate of Weld Area UT & MPI
in strict compliance with the API 5DP and Applicable Grant Prideco/GPJ Operating
Procedure for UT and MPI Inspection, Latest Revision.The issuance of this certificate
indicates that the Pipe Bodies, Tool Joints and Weld Area UT and MPI Inspection was
completed.
2018-12-12
NOV GP Order Confirmation Number: 1000128660 Customer Purchase Order Number: KUW00010
Description: (75) 2.875"OD 0.362" WT 10.4LB./FT. IU R2 CYX105-120 DRILL PIPE WITH HT2-7/8PAC PIN 3-1/8"OD×1-
1/2"ID & 9" PIN OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-7/8PAC
PIN AND HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID & 14"BOX OD LENGTH & H-SERIES BENCHMARK WITH TCS
8000 HARDBANDING FOR HT2-7/8PAC BOX.TK34 INTERNAL COATING
Page 1 of 2
JDAB17761 N/A 083664 362181 18DC00301 18702461 N/A 18DD02944 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17762 N/A 083664 362022 18DC00329 18702461 N/A 18DD03052 18702461 N/A 31.63 348.39 √ √ √ √ √
JDAB17763 N/A 083664 362118 18DC00331 18702461 N/A 18DD02942 18702461 N/A 31.59 352.80 √ √ √ √ √
JDAB17764 N/A 083664 362173 18DC00265 18702461 N/A 18DD02928 18702461 N/A 31.59 352.80 √ √ √ √ √
JDAB17765 N/A 083664 362190 18DC00317 18702461 N/A 18DD02972 18702461 N/A 31.66 349.49 √ √ √ √ √
JDAB17766 N/A 083664 362195 18DC00283 18702461 N/A 18DD02964 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17767 N/A 083664 362176 18DC00399 18702461 N/A 18DD02986 18702461 N/A 31.63 348.39 √ √ √ √ √
JDAB17768 N/A 083664 362185 18DC00333 18702461 N/A 18DD02924 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17769 N/A 083664 362106 18DC00293 18702461 N/A 18DD02922 18702461 N/A 31.63 350.60 √ √ √ √ √
JDAB17770 N/A 083664 362107 18DC00259 18702461 N/A 18DD02966 18702461 N/A 31.63 350.60 √ √ √ √ √
JDAB17771 N/A 083664 362123 18DC00271 18702461 N/A 18DD02916 18702461 N/A 31.63 352.80 √ √ √ √ √
JDAB17772 N/A 083664 362083 18DC00361 18702461 N/A 18DD03028 18702461 N/A 31.63 352.80 √ √ √ √ √
JDAB17773 N/A 083664 362101 18DC00335 18702461 N/A 18DD02992 18702461 N/A 31.63 350.60 √ √ √ √ √
JDAB17774 N/A 083664 362088 18DC00297 18702461 N/A 18DD02936 18702461 N/A 31.63 350.60 √ √ √ √ √
JDAB17775 N/A 083664 362097 18DC00387 18702461 N/A 18DD03026 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17776 N/A 083664 362087 18DC00285 18702461 N/A 18DD02950 18702461 N/A 31.66 353.90 √ √ √ √ √
JDAB17777 N/A 083664 362093 18DC00295 18702461 N/A 18DD02912 18702461 N/A 31.63 353.90 √ √ √ √ √
JDAB17778 N/A 083664 362090 18DC00273 18702461 N/A 18DD03036 18702461 N/A 31.63 352.80 √ √ √ √ √
JDAB17779 N/A 083664 362085 18DC00407 18702461 N/A 18DD03012 18702461 N/A 31.69 353.90 √ √ √ √ √
JDAB17780 N/A 083664 362091 18DC00391 18702461 N/A 18DD02958 18702461 N/A 31.63 348.39 √ √ √ √ √
JDAB17781 N/A 083664 362084 18DC00323 18702461 N/A 18DD03058 18702461 N/A 31.66 350.60 √ √ √ √ √
JDAB17782 N/A 083664 362098 18DC00347 18702461 N/A 18DD03044 18702461 N/A 31.63 348.39 √ √ √ √ √
JDAB17783 N/A 083664 362089 18DC00377 18702461 N/A 18DD02976 18702461 N/A 31.66 351.70 √ √ √ √ √
JDAB17784 N/A 083664 362117 18DC00339 18702461 N/A 18DD02980 18702461 N/A 31.59 349.49 √ √ √ √ √
JDAB17785 N/A 083664 362095 18DC00351 18702461 N/A 18DD02952 18702461 N/A 31.59 349.49 √ √ √ √ √
JDAB17786 N/A 083664 362167 18DC00257 18702461 N/A 18DD02910 18702461 N/A 31.63 350.60 √ √ √ √ √
JDAB17787 N/A 083664 362192 18DC00369 18702461 N/A 18DD03054 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17788 N/A 083664 362170 18DC00319 18702461 N/A 18DD03024 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17789 N/A 083664 362178 18DC00375 18702461 N/A 18DD02934 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17790 N/A 083664 362193 18DC00409 18702461 N/A 18DD02946 18702461 N/A 31.69 351.70 √ √ √ √ √
JDAB17791 N/A 083664 362184 18DC00359 18702461 N/A 18DD03050 18702461 N/A 31.66 349.49 √ √ √ √ √
JDAB17792 N/A 083664 362179 18DC00311 18702461 N/A 18DD02994 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17793 N/A 083664 362180 18DC00353 18702461 N/A 18DD02968 18702461 N/A 31.59 352.80 √ √ √ √ √
JDAB17794 N/A 083664 362160 18DC00381 18702461 N/A 18DD02948 18702461 N/A 31.63 352.80 √ √ √ √ √
JDAB17795 N/A 083664 362121 18DC00325 18702461 N/A 18DD03046 18702461 N/A 31.59 352.80 √ √ √ √ √
JDAB17796 N/A 083664 362120 18DC00313 18702461 N/A 18DD02938 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17797 N/A 083664 362124 18DC00275 18702461 N/A 18DD02988 18702461 N/A 31.63 350.60 √ √ √ √ √
JDAB17798 N/A 083664 362191 18DC00343 18702461 N/A 18DD02978 18702461 N/A 31.66 351.70 √ √ √ √ √
JDAB17799 N/A 083664 362146 18DC00401 18702461 N/A 18DD03010 18702461 N/A 31.66 350.60 √ √ √ √ √
JDAB17800 N/A 083664 362096 18DC00269 18702461 N/A 18DD02940 18702461 N/A 31.63 348.39 √ √ √ √ √
JDAB17801 N/A 083664 362187 18DC00299 18702461 N/A 18DD03040 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17802 N/A 083664 362200 18DC00337 18702461 N/A 18DD03042 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17803 N/A 083664 362104 18DC00287 18702461 N/A 18DD03034 18702461 N/A 31.66 350.60 √ √ √ √ √
JDAB17804 N/A 083664 363016 18DC00277 18702461 N/A 18DD02998 18702461 N/A 31.66 350.60 √ √ √ √ √
JDAB17805 N/A 083664 363010 18DC00393 18702461 N/A 18DD03060 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17806 N/A 083664 362099 18DC00371 18702461 N/A 18DD02918 18702461 N/A 31.63 350.60 √ √ √ √ √
JDAB17807 N/A 083664 362105 18DC00309 18702461 N/A 18DD03048 18702461 N/A 31.59 348.39 √ √ √ √ √
JDAB17808 N/A 083664 363012 18DC00327 18702461 N/A 18DD03014 18702461 N/A 31.63 352.80 √ √ √ √ √
客户: 日期 :
2018-12-12
Customer: TRINIDAD DRILLING LP Date :
格兰特订单确认号码: 客户采购订单号码:
NOV GP Order Confirmation Number: 1000128660 Customer Purchase Order Number: KUW00010
产品描述: (75) 2.875"OD 0.362" WT 10.4LB./FT. IU R2 CYX105-120 DRILL PIPE WITH HT2-7/8PAC PIN
Description: 3-1/8"OD×1-1/2"ID 9" PIN OD LENGTH H-SERIES BENCHMARK WITH TCS 8000 HARDBANDING
FOR HT2-7/8PAC PIN AND HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID 14"BOX OD LENGTH H-SERIES
BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-7/8PAC BOX.TK34 INTERNAL COATING
Page 2 of 2
JDAB17761
JDAB17809 N/A 083664 362181
363014 18DC00301
18DC00321 18702461 N/A 18DD02944
18DD02962 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17762
JDAB17810 N/A 083664 362022
363011 18DC00329
18DC00403 18702461 N/A 18DD03052
18DD03018 18702461 N/A 31.63
31.66 348.39
350.60 √ √ √ √ √
JDAB17763
JDAB17811 N/A 083664
282492 362118
363057 18DC00331
18DC00357 18702461 N/A 18DD02942
18DD02956 18702461 N/A 31.59
31.43 352.80
348.39 √ √ √ √ √
JDAB17764
JDAB17812 N/A 083664 362173
363009 18DC00265
18DC00281 18702461 N/A 18DD02928
18DD03016 18702461 N/A 31.59
31.69 352.80
351.70 √ √ √ √ √
JDAB17765
JDAB17813 N/A 083664
282492 362190
363056 18DC00317
18DC00349 18702461 N/A 18DD02972
18DD02996 18702461 N/A 31.66
31.40 349.49
352.80 √ √ √ √ √
JDAB17766
JDAB17814 N/A 083664
282492 362195
363066 18DC00283
18DC00363 18702461 N/A 18DD02964
18DD02954 18702461 N/A 31.63
31.40 349.49 √ √ √ √ √
JDAB17767
JDAB17815 N/A 083664 362176
362140 18DC00399
18DC00365 18702461 N/A 18DD02986
18DD03020 18702461 N/A 31.63 348.39
352.80 √ √ √ √ √
JDAB17768
JDAB17816 N/A 083664 362185
362157 18DC00333
18DC00379 18702461 N/A 18DD02924
18DD03002 18702461 N/A 31.63 349.49
350.60 √ √ √ √ √
JDAB17769
JDAB17817 N/A 083664 362106
362149 18DC00293
18DC00263 18702461 N/A 18DD02922
18DD03032 18702461 N/A 31.63
31.59 350.60
349.49 √ √ √ √ √
JDAB17770
JDAB17818 N/A 083664 362107
362125 18DC00259
18DC00383 18702461 N/A 18DD02966
18DD02930 18702461 N/A 31.63
31.69 350.60 √ √ √ √ √
JDAB17771
JDAB17819 N/A 083664 362123
362147 18DC00271
18DC00397 18702461 N/A 18DD02916
18DD03022 18702461 N/A 31.63
31.59 352.80
348.39 √ √ √ √ √
JDAB17772
JDAB17820 N/A 083664 362083
362165 18DC00361
18DC00307 18702461 N/A 18DD03028
18DD03062 18702461 N/A 31.63
31.59 352.80
349.49 √ √ √ √ √
JDAB17773
JDAB17821 N/A 083664 362101
362127 18DC00335
18DC00341 18702461 N/A 18DD02992
18DD03056 18702461 N/A 31.63 350.60
352.80 √ √ √ √ √
JDAB17774
JDAB17822 N/A 083664 362088
362166 18DC00297
18DC00389 18702461 N/A 18DD02936
18DD02960 18702461 N/A 31.63
31.69 350.60 √ √ √ √ √
JDAB17775
JDAB17823 N/A 083664 362097
362175 18DC00387
18DC00279 18702461 N/A 18DD03026
18DD02970 18702461 N/A 31.63
31.59 349.49
351.70 √ √ √ √ √
JDAB17776
JDAB17824 N/A 083664 362087
362174 18DC00285
18DC00385 18702461 N/A 18DD02950
18DD02974 18702461 N/A 31.66
31.63 353.90
348.39 √ √ √ √ √
JDAB17777
JDAB17825 N/A 083664 362093
362182 18DC00295
18DC00373 18702461 N/A 18DD02912
18DD02984 18702461 N/A 31.63
31.69 353.90
351.70 √ √ √ √ √
JDAB17778
JDAB17826 N/A 083664 362090
362168 18DC00273
18DC00315 18702461 N/A 18DD03036
18DD03030 18702461 N/A 31.63 352.80
349.49 √ √ √ √ √
JDAB17779
JDAB17827 N/A 083664 362085
362171 18DC00407
18DC00405 18702461 N/A 18DD03012
18DD03004 18702461 N/A 31.69 353.90
350.60 √ √ √ √ √
JDAB17780
JDAB17828 N/A 083664 362091
362194 18DC00391
18DC00305 18702461 N/A 18DD02958
18DD02932 18702461 N/A 31.63 348.39
349.49 √ √ √ √ √
JDAB17781
JDAB17829 N/A 083664 362084
362196 18DC00323
18DC00261 18702461 N/A 18DD03058
18DD02926 18702461 N/A 31.66
31.59 350.60
349.49 √ √ √ √ √
JDAB17782
JDAB17830 N/A 083664 362098
362189 18DC00347
18DC00355 18702461 N/A 18DD03044
18DD03038 18702461 N/A 31.63
31.69 348.39
352.80 √ √ √ √ √
JDAB17783
JDAB17831 N/A 083664 362089
362199 18DC00377
18DC00367 18702461 N/A 18DD02976
18DD02982 18702461 N/A 31.66 351.70
349.49 √ √ √ √ √
JDAB17784
JDAB17832 N/A 083664 362117
362169 18DC00339
18DC00395 18702461 N/A 18DD02980
18DD02920 18702461 N/A 31.59
31.63 349.49
350.60 √ √ √ √ √
JDAB17785
JDAB17833 N/A 083664 362095
362198 18DC00351
18DC00303 18702461 N/A 18DD02952
18DD02990 18702461 N/A 31.59
31.63 349.49
348.39 √ √ √ √ √
JDAB17786
JDAB17834 N/A 083664 362167
362183 18DC00257
18DC00267 18702461 N/A 18DD02910
18DD03006 18702461 N/A 31.63
31.59 350.60
349.49 √ √ √ √ √
JDAB17787
JDAB17835 N/A 083664 362192
362172 18DC00369
18DC00289 18702461 N/A 18DD03054
18DD02860 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17788 N/A 083664 362170 18DC00319 18702461 N/A 18DD03024 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17789 N/A 083664 362178 18DC00375 18702461 N/A 18DD02934 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17790 N/A 083664 362193 18DC00409 18702461 N/A 18DD02946 18702461 N/A 31.69 351.70 √ √ √ √ √
JDAB17791 N/A 083664 362184 18DC00359 18702461 N/A 18DD03050 18702461 N/A 31.66 349.49 √ √ √ √ √
JDAB17792 N/A 083664 362179 18DC00311 18702461 N/A 18DD02994 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17793 N/A 083664 362180 18DC00353 18702461 N/A 18DD02968 18702461 N/A 31.59 352.80 √ √ √ √ √
JDAB17794 N/A 083664 362160 18DC00381 18702461 N/A 18DD02948 18702461 N/A 31.63 352.80 √ √ √ √ √
JDAB17795 N/A 083664 362121 18DC00325 18702461 N/A 18DD03046 18702461 N/A 31.59 352.80 √ √ √ √ √
JDAB17796 N/A 083664 362120 18DC00313 18702461 N/A 18DD02938 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17797 N/A 083664 362124 18DC00275 18702461 N/A 18DD02988 18702461 N/A 31.63 350.60 √ √ √ √ √
JDAB17798 N/A 083664 362191 18DC00343 18702461 N/A 18DD02978 18702461 N/A 31.66 351.70 √ √ √ √ √
JDAB17799 N/A 083664 362146 18DC00401 18702461 N/A 18DD03010 18702461 N/A 31.66 350.60 √ √ √ √ √
JDAB17800 N/A 083664 362096 18DC00269 18702461 N/A 18DD02940 18702461 N/A 31.63 348.39 √ √ √ √ √
JDAB17801 N/A 083664 362187 18DC00299 18702461 N/A 18DD03040 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17802 N/A 083664 362200 18DC00337 18702461 N/A 18DD03042 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17803 N/A 083664 362104 18DC00287 18702461 N/A 18DD03034 18702461 N/A 31.66 350.60 √ √ √ √ √
JDAB17804 N/A 083664 363016 18DC00277 18702461 N/A 18DD02998 18702461 N/A 31.66 350.60 √ √ √ √ √
JDAB17805 N/A 083664 363010 18DC00393 18702461 N/A 18DD03060 18702461 N/A 31.63 349.49 √ √ √ √ √
JDAB17806 N/A 083664 362099 18DC00371 18702461 N/A 18DD02918 18702461 N/A 31.63 350.60 √ √ √ √ √
JDAB17807 N/A 083664 362105 18DC00309 18702461 N/A 18DD03048 18702461 N/A 31.59 348.39 √ √ √ √ √
JDAB17808 N/A 083664 363012 18DC00327 18702461 N/A 18DD03014 18702461 N/A 31.63 352.80 √ √ √ √ √
客户: 日期 :
2018-12-12
Customer: TRINIDAD DRILLING LP Date :
格兰特订单确认号码: 客户采购订单号码:
NOV GP Order Confirmation Number: 1000128660 Customer Purchase Order Number: KUW00010
产品描述: (75) 2.875"OD 0.362" WT 10.4LB./FT. IU R2 CYX105-120 DRILL PIPE WITH HT2-7/8PAC PIN
Description: 3-1/8"OD×1-1/2"ID 9" PIN OD LENGTH H-SERIES BENCHMARK WITH TCS 8000 HARDBANDING
FOR HT2-7/8PAC PIN AND HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID 14"BOX OD LENGTH H-SERIES
BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-7/8PAC BOX.TK34 INTERNAL COATING
Export Classification
ECCN#: EAR99
HTS#: 7304.23.1000
COUNTRY OF ORIGIN: CHN
All ECCN and HTS classification information received from National Oilwell Varco (NOV) is
for informational purposes only and shall not be construed as NOV’s representation,
certification or warranty regarding the proper classification. Use of such classification
information is at the Buyer’s sole risk and without recourse to NOV. The Buyer is
responsible for determining the correct classifications of all items prior to export and Buyer
shall make its own export licensing determinations.”
2018-12-12
NOV GP Order Confirmation Number: 1000128660 Customer Purchase Order Number: KUW00010
Description: (75) 2.875"OD 0.362" WT 10.4LB./FT. IU R2 CYX105-120 DRILL PIPE WITH HT2-7/8PAC PIN 3-1/8"OD×1-
1/2"ID & 9" PIN OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000 HARDBANDING FOR HT2-7/8PAC PIN
AND HT2-7/8PAC BOX 3-1/8"OD×1-1/2"ID & 14"BOX OD LENGTH & H-SERIES BENCHMARK WITH TCS 8000
HARDBANDING FOR HT2-7/8PAC BOX.TK34 INTERNAL COATING