Professional Documents
Culture Documents
Bird Strike Simulation For An Aero Engine Using LS-DYNA
Bird Strike Simulation For An Aero Engine Using LS-DYNA
Courses
Venkata Krishnan S
updated on 07 Mar 2021 commen
Project Details
Aim:
1) To create the simulation of bird strike on the Aero Engine from the given FE model.
2) Following are the information and conditions required to model the phenomenon
3) The blades should rotate at a constant velocity but the casing should remain stationary
4) The cylindrical bird model should travel along its own axis and hit the blades.
5) Use elastic material for the bird(2000MPa) and the casing(200GPa) and the material
model for the blades are given.
6) The velocity of the engine blades and the birds can be chosen so that blade failure can
be seen within a short span of time.
7) To follow a consistent numbering approach 100000+ for nodes, 500000+ for elements,
and 1000+ for the parts. All other keywords should be numbered within 10000-19999 while
following a range for each one.
8) The bird, casing and the blades should be indifferent input files as well as control cards
and boundary conditions and there should be one main file referencing all the input files.
9) The reference includes path should be such that the folder can be copied anywhere and
it can correctly reference all the file and run the simulation.
Theory:
The collision of birds on an aircraft while cruising in the air is called the Bird Strike event and
it is one of the most dangerous accidents that often occur. Therefore, certification of a bird
strike is one of the important processes in aircraft design. In particular, the areas where bird
strikes occur a lot are on the front leading edge of the wing, the cowling part of the engine,
https://skill-lync.com/student-projects/bird-strike-project-2-30 1/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
rotating engine fan blades, the cockpit transparency and the landing gear part. This
project is a classic nonlinear transient dynamics problem similar to a car crash and mobile
drop. While accurate modelling of the problem requires advanced techniques such as SPH
this problem can be solved using a generic explicit solver.
Procedure:
The given FE model of Aero Engine assembly is opened in LS-PrePost and each part is
assigned with section property and saved with ‘.k’ extension. The given FE model consists
of parts such as bird, blade, hub and casing.
1) Bird:
The given FE model of the dummy bird is retained and all other parts are deleted. The part
is assigned with section shell properties with ELFORM = 16 and thickness = 2.5 mm. The
keyword file is saved with a suitable name using the ‘.k’ extension.
https://skill-lync.com/student-projects/bird-strike-project-2-30 2/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
2) Blade:
The given FE model of blade is retained and all other parts are deleted. The part is assigned
with section shell properties with ELFORM = 16 and thickness = 1.2 mm. The keyword file is
saved with a suitable name using the ‘.k’ extension.
https://skill-lync.com/student-projects/bird-strike-project-2-30 3/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
3) Hub:
The given FE model of the hub is retained and all other parts are deleted. The part is
assigned with section solid properties with ELFORM = 4. The keyword file is saved with a
suitable name using the ‘.k’ extension.
https://skill-lync.com/student-projects/bird-strike-project-2-30 4/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
4) Casing:
The given FE model of the casing is retained and all other parts are deleted. The part is
assigned with section shell properties with ELFORM = 2 and thickness = 2 mm. The keyword
file is saved with a suitable name using the ‘.k’ extension.
https://skill-lync.com/student-projects/bird-strike-project-2-30 5/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
The MAT_ELASTIC material card with mid 11001 is assigned to part with PID 1001 i.e., bird.
The MAT_ELASTIC material card with mid 11003 is assigned to parts with
PID 1003 and 1004 i.e., hub and casing.
https://skill-lync.com/student-projects/bird-strike-project-2-30 6/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
https://skill-lync.com/student-projects/bird-strike-project-2-30 7/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
All the Materials and Sections were assigned to their respective parts i.e. Hub, Casing, Blade
and Bird.
https://skill-lync.com/student-projects/bird-strike-project-2-30 8/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
2. Boundary Conditions:
Boundary SPC:
As stated in the problem the casing has to be stationary, hence the degrees of freedom of
nodes in the casing is constrained in all direction.
https://skill-lync.com/student-projects/bird-strike-project-2-30 9/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
Initial Velocity:
1) The velocity of the engine blades and the birds are chosen so that blade failure can be
seen within a short span of time. Hence, the angular velocity of the blade is assumed as 0.5
rad/ms in the *Initial_Velocity_Generation card.
2) The velocity of the bird striking the blade is assumed as 20 mm/ms. The cylindrical bird
model is made to travel along its own axis and hit the blades.
https://skill-lync.com/student-projects/bird-strike-project-2-30 10/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
3. Contact Cards:
1) In the case of bird impacting the fan blades directly, it is important to assign the proper
contact between,
https://skill-lync.com/student-projects/bird-strike-project-2-30 11/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
2) Contact between bird and fan blades was defined by using
the *Contact_Automatic_Nodes_to_Surface where the bird is the nodes and blades are
surfaces. The impact of the bird with a blade induces reaction loads that counter the
rotational forces of the blade thus deforming the blade enough or fracture, portions of the
same blade may even come into contact with the remaining blade and casing.
2) The hub and blade are held together using the *Contact_Tied_Surface_to_Surface.
3) The contact between fan blades with other blades is defined using the
*Contact_Automatic_Single_Surface.
https://skill-lync.com/student-projects/bird-strike-project-2-30 12/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
4) The contact between damaged fan blades with the casing is defined using the
*Contact_Surface_to_Surface.
4. Control Cards:
https://skill-lync.com/student-projects/bird-strike-project-2-30 13/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
2) The *Control_Termination is used to set the termination time which is set as 4 ms in thi
case.
3) The *Control_Hourglass is used to control the hourglass effect if present in the model
during simulation.
https://skill-lync.com/student-projects/bird-strike-project-2-30 14/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
5. Database Cards:
1) The time step value of 0.1 ms is given for the BINARY_D3PLOT and in
the DATABASE_ASCII option for GLSTAT, MATSUM, RCFORC and SLEOUT.
2) *DATABASE_EXTENT_BINARY card with STRFLG =1, is used to compute the elastic strain
in the model.
https://skill-lync.com/student-projects/bird-strike-project-2-30 15/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
The bird, blade, hub, casing, material, boundary condition, contact and control database
are in different input files. Hence to reference these input files to one main file, Open LS-
PrePost, in the *INCLUDE card type the input keyword file names and insert it and save
them as the main keyword file with the ‘.k’ extension. The reference includes a path that is
such that the folder can be copied anywhere and it can correctly reference all the files and
run the simulation.
7. Model Checking:
The model checking is done in the main file to find out for any errors or warnings in the
model. It was found there are no errors or warnings.
https://skill-lync.com/student-projects/bird-strike-project-2-30 16/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
8. Runumbering:
Renumbering is done by selecting individually the keywords like nodes, elements, parts etc
and entering the Start ID value and click Set and Renumber. A consistent numbering
approach is followed i.e., 100000+ for nodes, 500000+ for elements, and 1000+ for the parts
All other keywords are numbered within 10000-19999 while following a range for each one.
These requirements are necessary for a professional setting when dealing with large
models and multiple people working with the same model simultaneously.
https://skill-lync.com/student-projects/bird-strike-project-2-30 17/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
https://skill-lync.com/student-projects/bird-strike-project-2-30 18/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
From the simulation, it is observed that the bird striking the blades of the Aero Engine gets
damaged. The stress and strain induced in the impacting zone are more such that the
blades are broken and gets permanently deformed.
An element 507697 of the blade at the impact zone is taken to plot the graph of v-m stress
From the graph, it is observed that the v-m stress induced in the element is maximum and
reaches a value of 0.0702 GPa at around 3.1 ms which is more than the yield stress value
of 0.013362 GPa of the blade material. Hence, the blade is damaged.
https://skill-lync.com/student-projects/bird-strike-project-2-30 19/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
From the graph, it is observed that the Effective plastic strain induced in the
element 508593 is maximum and reaches a value of 0.0875 at time 1.7 ms during the
impact and remains the same till the end of the simulation. Hence, the blade is deformed.
4. Energy Plots:
From the energy plot graph, it is observed that the kinetic energy is reduced during the tim
of the bird striking the blade of Aero Engine. The internal energy is increased due to the
decrease in kinetic energy. The hourglass energy remains 0 during the entire time of the
simulation since we are using the ELFORM 16 (Fully Integrated Element Formulation) for
the blade and bird also we are using the *Control_Hourglass to reduce the hourglass
effect. The total energy remains constant throughout the simulation.
5. Mass Scaling:
1) Without Mass-Scaling:
The estimated time required to complete the simulation was shown as 1 hrs 33 mins but
actually, it took only 40 mins to complete the task. A mass scaling approach can be
adopted to reduce the runtime.
https://skill-lync.com/student-projects/bird-strike-project-2-30 20/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
2) With Mass-Scaling:
For, DT2MS = -6.14E-5, the estimated clock time to complete the simulation for TSSFAC=
0.9 is 1 hrs 33 mins. The percentage increase in mass is 0%.
For, DT2MS = -8.00E-5, the estimated clock time to complete the simulation for TSSFAC=
0.9 is 2 hrs 48 mins. The percentage increase in mass is 0.00027193%.
https://skill-lync.com/student-projects/bird-strike-project-2-30 21/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
For, DT2MS = -1.00E-4, the estimated clock time to complete the simulation for TSSFAC=
0.9 is 1 hrs 7 mins. The percentage increase in mass is 0.0090455%.
For, DT2MS = -2.50E-4, the estimated clock time to complete the simulation for TSSFAC=
0.9 is 27 mins. The percentage increase in mass is 8.3602%.
https://skill-lync.com/student-projects/bird-strike-project-2-30 22/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
As per industry standards, for a dynamic simulation, 10 % is the limit set for mass scaling.
After simulating the current case I didn't see any significant changes between the one with
mass scaling and the one without mass scaling. I also understand that we are doing mass
scaling to only decreasing the simulation time for the current model.
6. Debugging:
https://skill-lync.com/student-projects/bird-strike-project-2-30 23/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
Hence to resolve this issue, the keyword file was debugged by running the file for several
iterations of assumed parameters with the help of a literature survey. The issue was
resolved by changing the value of the density of material for the bird and also changing
the elform to 16.
Conclusion:
1) The keyword file to simulate bird strike on an Aero Engine is created by following the
necessary conditions and requirements.
2) In the simulation, the blades at the impact zone are damaged and deformed.
3) Mass scaling approach was adopted to reduce the runtime with the optimum value
of DT2MS = -2.50E-4.
4) The initial keyword files were debugged to get a realistic simulation of the bird strike
phenomenon.
5) Learned to create and organise as well as debug the input keyword files similar to a
professional setting when dealing with large models and multiple people working with the
same model simultaneously.
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the
comments are moderated as per our comment policy, and your email will not be
https://skill-lync.com/student-projects/bird-strike-project-2-30 24/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
published for privacy reasons. Please leave a personal & meaningful
conversation.
Other comments...
No comments yet!
Be the first to add a comment
Objective: Objective:
Aim: 1) To create the simulation of bird Aim: To demonstrate spherical, revo
strike on the Aero Engine from the given cylindrical, and translational joints
FE model. 2) Following are the between two rigid bodies and two
information and conditions required to deformable bodies. Theory: A
model the phenomenon 3) The blades… distinguishing feature of multibody…
LS-DYNA
Showing 1 of 46 projects
https://skill-lync.com/student-projects/bird-strike-project-2-30 25/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
Our Company
News & Events
Blog
Careers
Grievance Redressal
Skill-Lync Reviews
Terms
Privacy Policy
info@skill-lync.com
ITgrievance@skill-lync.com
Top PG Programs
Post Graduate Program in Hybrid Electric Vehicle Design and Analysis
Skill-Lync Plus
Executive Program in Electric Vehicle Embedded Software
https://skill-lync.com/student-projects/bird-strike-project-2-30 26/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
Executive Program in Cybersecurity
Trending Blogs
Octave Code for Creating GIF Animation Files: A Step-by-Step Tutorial
Support
https://skill-lync.com/student-projects/bird-strike-project-2-30 27/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
https://skill-lync.com/student-projects/bird-strike-project-2-30 28/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
https://skill-lync.com/student-projects/bird-strike-project-2-30 29/30
1/27/24, 10:51 PM Bird Strike Simulation for an Aero Engine using LS-DYNA
https://skill-lync.com/student-projects/bird-strike-project-2-30 30/30