COS 0642 Lab Works Jan 2024

GMI German-Malaysian Institute
DIPLOMA PROGRAMME
LAB WORKS 20%

Academic Period: January 2024
Program : NETWORK SECURITY

Course : WIRELESS NETWORK SECURITY
Code : COS 0642
Duration : 3 HOURS FOR EACH LAB WORK
Total Marks :
GENERAL INSTRUCTIONS:
1. Write down clearly (with capital letters) your name, trade, group and the date
of examination at the bottom of this page.
2. Do not open this question booklet until you are told to do so by the invigilator.
3. Read the specific instructions and questions carefully before answering.
1. Muhammad Zaim Zuhdi Bin Noor Hisham

Student’s Name :
1. NWS22070173
Student’s I/D No. :
Semester/Trade/Group : JULY 22/NWS/G3

Date : 3/2/2024
COS 0642 WIRELESS NETWORK SECURITY
Level
Full
No Assessment Criteria CLO PO of Score Marks Comment
Marks
Diff
1. Lab work #1 – Chapter 2 2 4 P3 15
Packet Tracer – Configure a basic
WLAN on the WLC
2 Lab work #2 – 2 4 P3 15
3. Lab work #3 – 2 4 P3 15
4. Lab work #4 2 4 P3 15
Lab work #5
5 P3 15
2 4
Lab work #6
6 2 P3 15
4
Total 90
Total Marks /90
Total PO 4 /90
Signature
Page 2 of 17
Copyright of German-Malaysian Institute. All rights reserved.
SCHEME – each lab work given
APPROACHES EXPECTATIONS
NO. CRITERIA MEETS EXPECTATIONS [2] EXCELLENT [3] MARKS
[1]
LAB WORKS
Able to setup network without

1 Setup Network Unable to setup network without Able to setup network with
assistance.
Cabling and setup network major assistance. little assistance.
Configurations:
2 Solving the lab Unable to configure most of the Able to configure most of the Able to configure all
configuration task given task given configuration given.
Verification:
Unable to verify most of the Students able to verify most Student able to verify all
3 Test connection
configurations. of the configurations. configurations.
Interpretation: Unable to interpret most of the Able to interpret all the findings
4 Able to interpret most of the
Interpreting findings. findings and result. and result clearly and
findings and result.
comprehensively.
Only restatement of the instruction
without commenting on the Shows a little understanding
5 Knowledge Shows a full understanding of
expected key point. Incorrect of what the practical was
what the practical was about.
judgment/arguments are used. about.
TOTAL
ANSWER, RESULTS OUTPUT AND ELABORATE THE FINDINGS
You are required to follow the step given:
Step 1: Screen capture the steps and result at every lab works given.
Step 3: Submit the lab sheet in PDF format and rename the file with your full name and student ID.
Lab work #1
1. Open Desktop of Admin PC and enter the Ip-Address of WC-1 with HTTPS protocol (192.68.200.254)
2. It will redirect you to the Wireless Lan Controller .
3. Enter the login credentials ( username: admin password: Cisco123)
4. Go to the Wlan tab and create new ( click go for next step)
Page 5 of 17
5. Create the Profile Name, SSID and ID ( Floor Employees 2, SSID-5, 5 (optional as to keep
consistent with vlan number and SSID)) click apply to continue and click Enabled to make
the WLAN functional
6. Click on the General Tab and edit the Profile Name, SSID. Enabled the status and select the
interface to WLAN-5 and click apply to continue
7. Click the advanced tab, scroll down to find the FlexConnect option. Enabled the
FLexConnect Local Switching and Local Auth. Click apply to continue
Page 6 of 17
8. Go to the Security tab, select WPA + WPA2 as Layer 2 security, enable WPA2 Policy and
Encryption, Enable the PSK Authentication.
9. Enter the password optional ( for here I enter Cisco123 as same password). Click apply to
save settings and continue
10. Go to Wireless Host Desktop and select PC Wireless
11. Click the Connect tab, the SSID-5 will appear after a short delay. Select it and click the
connect button
Page 7 of 17
12. Enter the pre-shared key from the same password of WLAN configured
13. Go to Link Information tab and Click More Information to see the details of connection
Page 8 of 17
14. Go to Ip configuration at Pc Wireless Desktop and whether the host have receive the Ip
address over DHCP.
15. Ping the WLAN default gateway and Server to verify full connectivity
Page 9 of 17
Lab work #2
1. Login to Desktop Admin Pc and select the browser

2. Connect to the IP address of the WLC over https://192.168.200.254
3. Enter the username and password
4. Go to Controller menu and click interfaces
5. Create new interface name (WLAN-5, Vlan Id 5).Click apply to continue.
6. Address the interface as follows:

Page 10 of 17
IP Address: 192.168.5.254
Netmask: 255.255.255.0
Gateway: 192.168.5.1
Primary DHCP server: 192.168.5.1
Set the port number as 1.
Never forget click apply and save configuration so WLC will be in effect
7. Click the Security menu.

8. Click the New button to continue
9. Enter Ip address of the Radius Server, and use Cisco123 for the shared secret value.Confirm
the info and click apply
10. To create WLAN entry, click the New button at WLANs and Go.
11. Create the Wlan as follows: Profile Name : Floor 2 Employees , SSID : SSID-5 , ID : 5
(Recommended)
Page 11 of 17
Click apply to accept the settings.
12. Go to General Tab. Make sure to click enabled for wlan to be functional. Select the
Interface/Interface Group(G) for WLAN-5.
13. Go to Advanced tab. Scroll to FlexConnect and enable FlexConnect Local Switching and
FLexConnet Local Auth
Click apply to save your settings.
14. Go to Security Tab and select WPA+ WPA 2 to configure the security.
Page 12 of 17
15. Enable WPA2 Policy and Encryption and 802.1X.
16. Click AAA servers and select the RADIUS IP and port in server 1.
Click apply to continue and save your settings.
17. In the left hand menu, expand the Internal DHCP Server and select DHCP Scope.
18. Go and create Wired Management in the new button as new DHCP scope
19. Enter the value for the Pool Start and End Address. Select the status as Enabled
Page 13 of 17
Enter the values for Network, Netmask and Default Routers too. Click apply to save the
settings
20. Click Management menu and expand the SMNP and select Trap Receivers and create New
21. Named the SMNP as WLAN_SMNP and the IP address ( 172.31.1.254).
Click apply to save the configuration
22. Go to Wireless Host and select PC Wireless app. Click the Profiles tab and create new. Name
the profile WLC NET.
23. Go to Advanced Setup and verify Wireless Network Name.
Page 14 of 17
24. Click next and make sure DHCP Settings have selected.
25. In Security box, select he WPA2-Enterprise.Click Next
26. Enter Login name as user1, the password is User1Password
27. Verify the Profile Settings and click Save.
28. Click connect to Network
29. The Wireless Host connec t to LAP-1

Page 15 of 17
30. Ping the Radius Server ,Default Gateway and SW1.
Successful ping indicate full connectivity of the topology.
Lab work #3
Page 16 of 17
Lab work #4
Lab work #5
Lab work #6
Page 17 of 17

COS 0642 Lab Works Jan 2024

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

COS 0642 Lab Works Jan 2024

Uploaded by

Copyright:

Available Formats

GMI German-Malaysian Institute

LAB WORKS 20%

Program : NETWORK SECURITY

1. Muhammad Zaim Zuhdi Bin Noor Hisham

Semester/Trade/Group : JULY 22/NWS/G3

Able to setup network without

You are required to follow the step given:

2. It will redirect you to the Wireless Lan Controller .

3. Enter the login credentials ( username: admin password: Cisco123)

10. Go to Wireless Host Desktop and select PC Wireless

1. Login to Desktop Admin Pc and select the browser

6. Address the interface as follows:

7. Click the Security menu.

Click apply to accept the settings.

Click apply to save your settings.

15. Enable WPA2 Policy and Encryption and 802.1X.

Click apply to continue and save your settings.

Click apply to save the configuration

23. Go to Advanced Setup and verify Wireless Network Name.

25. In Security box, select he WPA2-Enterprise.Click Next

26. Enter Login name as user1, the password is User1Password

27. Verify the Profile Settings and click Save.

28. Click connect to Network

29. The Wireless Host connec t to LAP-1

30. Ping the Radius Server ,Default Gateway and SW1.

Successful ping indicate full connectivity of the topology.

You might also like