Professional Documents
Culture Documents
Ult-3000-Se-Im-08 (Dicksdon 30.04.2018)
Ult-3000-Se-Im-08 (Dicksdon 30.04.2018)
INSTRUCTION MANUAL
ULT-3000 Instruction Manual
Table Of Contents
SEC
CTION 1: IN
NTRODUCTION
The ULT- 3000 UNIVERSAL LAB TRA AINER is an ideal teachinng aid for alll types of eleectronic circuuits. There are
varieety of function
nal input andd output circuits (see Featu
ures) which can be used too stimulate orr measure eleectrical signals
from
m the circuit under
u test or development.
d . These circuit functions aallow for the testing of cirrcuits withouut the need fo
or
manyy expensive in ndividual piecces of equipm
ment.
SEC
CTION 2: FE
EATURES
• CCompletely Self-Contain
S ed Unit
• DDC Power Su upplies
• 33-State Logicc Probe
• AAC Power Su upplies
• DDC Power Su upplies:
o Fixed : +5V/0 0.5A, -5V/0.5A
A, +12V/0.5A A, -12V/0.5A
A,
o Variable
V : +0V
V to +23V, 0.5
5A; -0V to -2
23V, 0.5A.
• 2 Channels Function
F Gennerator with Sine, Trianggle and Squaare Wave Ouutputs with selection freequency from m
110 Hz to 500KHz in 6 decades.
• 2 Channels TTL
T / Clock Generator
G with fine adjust, amplitudee and DC off
ffset control w
with clock ouutput 1 Hz to
o
5500KHz in 6 decades.
• 22-Single Shot Pulse Switcches, 80µS
• 116-bit LED Indicators with Buffer
• PPotentiometeer 10KΩ, 50K KΩ & 100KΩ Ω
• 2 X 7-Segmeent & BCD Display
D
• SSpeaker, 8Ω, 0.25W with h Buffer
• 2 Logic Switches (+5, 0V V)
• 116 HI/LO Daata Output Sw witches (+5, 0V)
• TTTL/CMOS mode
m selection switch
• 5 Numbers 4m mm & 8 Num mbers 2mm Sockets
S to Turn Pin Headder Adaptorss
• 11680 tie poin
nts Breadboard
• DDigital DC Volt
V Meter
SEC
CTION 3 : PR
REPARATIION FOR USE
3-1 : Unpacking
g and Conten
nts Check
The ULT-3 3000 comes complete an nd ready to use.
u Check thhe followingg componentts list when uunpacking. If
any ppieces are missing, immeediately notiffy the distrib
butor you purrchased the iinstrument frrom.
11) ULT-300
00 Universal Lab Trainer
22) AC Poweer Cable
33) Instructio
ons Manual
EDU
ULABS DID
DACTIC 2 ww
ww.scienscoppe.com.my
ULT
T-3000 Instru
uction Manu
ual
Inspect th
he ULT-3000 0 for any sign
ns of damagee. Make sure that the pow
wer cord is foor your voltaage 240 VAC
C.
Allow
wable input voltages
v are ass follows:
C @ 50Hz, ±10%
240 VAC
CAU
C UTIO
ON
Should thhe ULT-3000 0 UNIVERSA AL LAB TRA AINER fail tto operate aftfter applying AC power ccheck the fuse
locatted on the bacck panel. Repllace with the same type an
nd style fuse oof 3A, 240V oor equal speciifications.
WAR
RNING
G
It is recom
mmended thatt during the first
f operation
n of the ULT--3000 the Pree-Operation chhecks are perrformed as peer
sectioon 3. These checks
c will help to verify the proper opperation of thhe ULT-30000 UNIVERSA AL LAB TRA AINER. These
checkks can also bee made at any
y time in the future
f as a parrtial performaance test.
EDU
ULABS DID
DACTIC 3 ww
ww.scienscoppe.com.my
ULT
T-3000 Instru
uction Manu
ual
SECTION 4: CO
ONTROLS AND
A INDICA
ATORS
18 6
17
16
155 14 13 12 11 10 9 8
EDU
ULABS DID
DACTIC 4 ww
ww.scienscoppe.com.my
ULT
T-3000 Instru
uction Manu
ual
Ind
dex
Control orr Indicator F
Function
N
No.
1 Power Switch Provide the On/O Off switchingg of incomingg power.
Digital DC Voltmeteer Provide DC volttage measurem ment
(i) On n/Off Switch Provide the On/O Off switchingg of Digital DC Voltmeter
Fou ur voltage rannges :
0V to 199.9VDC C
0V to 19.99VDC C
2
(ii) DC
C Voltage Raange Switch 0V to 1.999VDC C
0V to 199.9mV VDC
Input Impedancce: 10Mohm for any rangge
Acccuracy : +/-100%
(iii) 4 digits
d 7-Segm
ment Display Provides four diggits of measuured DC voltaage
Provides two diggits of Binaryy-Code-Decim mal to 7-Segm
ment
3 7-Segm
ment Display & BCD
Deccoder
4 Speakeer 8 Ohm/0.25W
O Sppeaker with bbuffer
Provides 8 indeppendent LED's with buffereed inputs.
5 16 Bit LED
L Display
y ( lab
beled L0 ~ L 15 )
6 AC Powwer Supplies Proovides two 199VAC, two 115VAC and ooutputs
7 4mm Adaptor
A Provides 5 numbbers 4mm soccket to turn piin headers
8 Three (3)
( State Logiic Probe Provides for the three states TTTL and CMO OS logic signnal testing.
Provides two inddependent 80uuS pulses of ppositive and nnegative
9 Pulse Switches
S
edgge trigger
110 Logic Switches
S Provide two setss of logical ouutput X/inversse X, Y/inverrse Y
111 Data Sw
witches Provides 16 sets of data switcching of "+5V V" and "0V" ooutputs
112 TTL/CMOS selectio on switch Seleect TTL or CM MOS Mode ffor data switcches ONLY
113 Amplittude Control Adjjusts the ampllitude of the FFunction Gennerator Wavefform
Provide frequenccy adjustable output Squaare waveform,, Frequency
114 DC offfset Control
rangge from 1Hz to 500kHz inn 6 decades w with fine Adjusst
Adjjusts the variaable frequency of the functtion generatorr & Clock
115 Frequen
ncy Control baseed upon the FFrequency Raange Switch setting
Seleects the rangee of the frequeency in timess 10 incremennts for
Funnction Generaator & Clock Generator. Sw witch Positionn Range
x 100 1 Hz - l0 Hz
x 1000 10 Hz - 100 Hz
116 Frequen
ncy Range Sw
witch
x 1kk l00 Hzz - 1 kHz
x 100k 1 kHz - l0 kHz
x l0
00k 10 kHzz - l00 kHz
x 1MM 100 kHHz – 500kHz
117 Wavefo
orm Selection
n Seleect Waveform m for Square, Triangle andd Sine wave
Suppplies Six DCC power suppllies as follows
+5VV & -5V @ 0.5A max
+122V & -12V @ 0.55A max
118 DC Pow
wer Supply
+V (+0V ~ +23V Vdc) @ 0.5A A max
-V (-0V
( ~ -23Vddc) @ 0.5A max
SECTION 5: SPE
ECIFICATIONS, OPER
RATION, PRE-OPERATIION AND A
APPLICATIO
ONS
EDU
ULABS DID
DACTIC 5 ww
ww.scienscoppe.com.my
ULT-3000 Instruction Manual
The following section covers the above four topics grouped for each function. The pre-operation procedures,
when provided are to verify that functional circuits are operating and to help gain familiarity with the equipment features.
Refer to section 4 for all ULT-3000 controls, indicators and functions when performing the pre-operation checks.
Figure 1
The main power switch controls the power source for the whole trainer. The trainer will only get the power source
when the power switch has been turned on, and the light on the switch is on.
Figure 2
5-2.1: Variable Supplies
Specifications:
Output Voltage: +0V to +25V, -0V to -25V
Output Current: 1.0A max
Line Regulation: < 1% @ 0 - 25Vdc
Load Regulation: < 30mV @ 0 – 0.5A
Operation:
The two independent variable power supply outputs are connected between the "+V and GND" and also
the "-V and GND". Each output is controlled individually by the "+V" and "-V" controls.
Application:
The variable power supply outputs can be used to power different linear devices such as operational
amplifiers and TTL, CMOS, and compatible logic devices.
Specifications:
Output Voltage: +5 ± 0.25 Vdc
Output Current: 0.5A max
Specifications:
Output Voltage: -5 ± 0.25 Vdc
Output Current: 0.5A max
Application:
The +5 and -5 power supplies can be used as the source power of logic circuits such as TTL or CMOS.
Specifications:
Output Voltage: +12 ± 0.25 Vdc
Output Current: 0.5A max
Specifications:
Output Voltage: -12 ± 0.25 Vdc
Output Current: 0.5A max
Application:
The +12 and -12 power supplies can be used as the source power of logic circuits such as TTL or CMOS.
5-3: Speaker
Figure 3
Specifications:
Operation:
Connect the signal to the input market "+" and "-" speaker input. The input should not exceed 1/4 watt. (V less
than 2.83 Vrms, 4 Vpeak, or 8 Vp-p)
Pre-Operation Check:
1. Connect the "~" sine function generator output to the "+" speaker input.
2. Connect the GND of the function generator to the "-" speaker input.
3. Set the frequency range switch to the "X100" position and slowly increase the amplitude control until the
speaker sounds.
Application:
For exercising the audio experiment, use the speaker as the output load. When there has some
Response, sound can be heard from the speaker.
Figure 4
Specifications:
Frequency Ranges: 1 Hz to 10 Hz
10 Hz to 100 Hz
100 Hz to 1 kHz
1 kHz to 10 kHz
10 kHz to 100 kHz
100 kHz to 500 kHz
The output frequency is continuously variable between these ranges by adjusting the variable frequency control
knob.
The amplitude is variable for the sine wave, triangle and square wave by adjusting the amplitude control knob.
Figure 5
Operation:
The output of each function is made at the terminals as shown in Fig 4. All outputs are available simultaneously at
the same frequency. Select the frequency range and then fine tune the frequency using the Variable Frequency
Control Knob. Adjust the amplitude of the sine, triangle and Square wave using the Amplitude control.
Pre-Operation Check:
The output of the function generator can be observed by using an oscilloscope. Connect the outputs to the
oscilloscope being certain to connect GND to GND between the Oscilloscope and ULT-3000. The GND on the
ULT-3000 is common with the AC Power ground connection. Most oscilloscopes also have their input ground pin
common with the AC power ground of the oscilloscope. Please make sure that the grounds are connected properly.
Application:
The function generator can be used to generate input stimuli waveforms for all types of digital and analog circuits.
It should be noted however that for triggering TTL and compatible gates the negative portion of the square wave
should be removed. This can be accomplished by using a comparator or clipping circuit.
Figure 6
Specifications:
Outputs: 0 or +5V (TTL) / +12V (CMOS) Break before make switches
Pre-Operation Check:
1. Connect the "0" Data switch to the DMM input.
2. Connect the GND to the DMM input.
3. Turn the selector switch to TTL output (+5V)
4. Set the "0" Data Switch to the "0" position and verify that the DMM reads approximately 0 volts.
5. Set the "0" Data Switch to the "1” position and verify that the DMM reads approximately +5 volts.
6. Repeat steps 1 - 4 for "1 “through "15" Data Switches.
7. Turn the selector switch to CMOS output (+12V)
8. Set the "0" Data Switch to the "0" position and verify that the DMM reads approximately 0 volts.
9. Set the "0" Data Switch to the "1” position and verify that the DMM reads approximately +12
volts.
10. Repeat steps 1 - 4 for "1 “through "15" Data Switches.
Applications:
The Data Switches "0" - "15" provide a logic high (+5V) / CMOS (+12V) or low (0 V) output which are
short circuit current limit protected. These switches are placed in an open circuit state condition when the
switch is activated. These switches can be used independently to provide a 1 or 0 logic state, or they can
be used together to represent an 8 bit byte, BCD or other coded input. And it’s also can be use to provide
CMOS outputs.
Figure 7
Specification
Output Vo High 2.7 to 5.0V
Vo Low 0 to 0.5V
Figure 8
Operation:
1. When the ‘ ’ positive pulse switch is depressed, the circuit will generate a single positive pulse of
approximately 80uS duration. When the switch is not pressed the output is at, normally low output
level.
2. When the “ ” negative pulse switch is depressed, the circuit will generate a single negative of
approximately 80uS duration. When the switch is not pressed the output is at a normally high output
level.
Application:
The pulse switches provide a clean pulse with position and negative transitions which can be to trigger edge
sensitive input devices such as the Flip Flop gates.
Figure 9
Specification
Output: 0 or +5Vdc.
Pre-Operation Check:
1. Connect the "Y" switch output to the DMM input and the GND to the "-" DMM input.
2. Set the switch to the "on" position and verify the DMM reads approximately +5V.
3. Now connect the "Y’" switch output to the DMM input and the GND to the "-" DMM input.
Verify the DMM reads approximately 0 V.
4. Connect the "Y" switch output to the DMM input and the GND to the "-" DMM input.
5. Set the switch to the "off" position and verify the DMM reads approximately 0V.
6. Now connect the "Y’" switch output to the DMM input and the GND to the "-" DMM input.
Verify the DMM reads approximately +5 V.
7. It worked similar for the X switch.
Figure 10
Specifications:
Inputs: 0V to 5 Vdc
Operation:
1. When the input of probe is logic high state, the TOP LED (which beside HI) will on to indicate high.
2. When the input is logic low state, the BOTTOM LED (which beside LO) will on to indicate low.
3. If the input is floating state or none connecting any input, the MIDDLE LED (which beside "-") will on.
Pre-Operation Check:
1. Connect the probe "IN" to the Data Switch "0"; and set the "0" Data switch to the "1” position to verify
that the probe displays "1 ".
2. Set the "0" Data Switch to the "0" Position to verify that the probe displays "0"
3. Non connect the probe "IN" to verify that it displays
Application:
If just want to know some position to designed circuit is logic high or low state, using the 3 state logic
probe to test is more convenient. From the display can ensure the circuit state is high (1”), low ("0"), or
open ("-").
Figure 11
Specifications:
Inputs: +5 to +15 Vdc
Operation:
The LED display provides a visual indication of the high or low status of the input logic signals. Each input must
be held at a high (+5Vdc) level in order to illuminate the respective LED.
Pre-Operation Check:
1. Connect the outputs of the 16 Data Switches to the corresponding LED inputs. The GND connection is tied
internally and need not be connected.
2. Set the data switches to various positions and verify that the LEDs illuminate when the data switches are in
the “1” position.
Application:
The LED’s can be used to display an 16 bit binary integer or two BCD integers in binary format.
Figure 12
Specification:
1. Consist of two 19VAC, two 15VAC outputs.
Operation:
Connect one of the outputs to one of the 19V/15V point and another output to one of the point 0.
Figure 15
Specification:
Two sets of BCD (Binary Code Decimal) with 7-segment LED display.
Operation:
The 7-segment LED display 7S-1 and 7S-2 show “0” when connected to 4 Data Switches at low state, which
means the binary input is 0000, so decimal reading is 0. When Data Switch 7 (right side) at up position (output +
high), the LED display will show”1”, that means the binary input is 0001, so decimal reading is 1. Set the Data
Switch 6 at up position, the LED now shows "3", that means the binary input is 0011, so decimal reading is 3.
Proceed to the step with Data Switches 5 & 4, and observe the number displayed on the LED. It will changed by
different binary input.
Application:
Table of BCD Chart
0001 1 1001 9
0010 2 1010 10
0011 3 1011 11
0100 4 1100 12
0101 5 1101 13
0110 6 1110 14
0111 7 1111 15
5-12: 4mm Adaptor Interface
Figure 16
The 4mm adaptor consists of four sockets (4mm size) where the outputs for each sockets connected directly to 4
numbers of turn pins.
SECTION 6: MAINTANANCE
WARNING
Remove power prior for performing maintenance on equipment. Failure to do so can cause serious
injury to personnel.
Maintenance consists of fuse replacement, calibration adjustment procedures, and periodic cleaning. Performing the
calibration and adjustment procedures only by Authorized Service Engineer, otherwise the warranty will void.
CAUTION
The following procedures should only be performed by persons trained and qualified in electronics and
electronic equipment service. Do not attempt these procedures if not qualified.
6-2: Cleaning
The ULT-3000 can be cleaned with a dry, soft cloth to remove any oil, grease, or grime from the equipment.
Never use liquid solvents or detergents. If the equipment got wet for any reason, dry using low pressure air (less
than 25 PSI). Use care and caution around areas where water or air could enter the interior of the equipment while
drying.
EDU
ULABS DID
DACTIC 16 ww
ww.scienscoppe.com.my
ULT-3000 Instruction Manual
EDU
ULABS DID
DACTIC 20 ww
ww.scienscoppe.com.my
ULT
T-3000 Instru
uction Manu
ual
EDU
ULABS DID
DACTIC 21 ww
ww.scienscoppe.com.my
ULT
T-3000 Instru
uction Manu
ual
SECTION 8: WA
ARRANTY AND
A STAND
DARD COND
DITIONS OF
F SALE
LIM
MITATION OF
O LIABILIT
TY
GEN
NERAL CON
NDITIONS
All oorders are subjject to accepttance by Selleer at its Main Office. Stenoographic and clerical errors are subject tto correction..
No ooral or subsequuent modificaation or any other
o foregoin
ng general proovisions or off any term or condition of aany order
shall be binding unless
u agreed to
t in writing by
b the Seller and Purchaseer.
SC
CIEN
NSCOP
PE SD
DN BH
HD
(Com mpany No: 520887-D)(G
5 GST Reg No o: 000154509
9312)
20, JJalan BP 5/10, Bandar Bukit
B Puchon
ng,
471000 Puchong, Selangor, Malaysia.
M
Tel: 6012-40804 443
E-maail: sales@scienscope.coom.my
Webbsite: http://w
www.sciensccope.com.myy
EDU
ULABS DID
DACTIC 22 ww
ww.scienscoppe.com.my