Professional Documents
Culture Documents
40R Repair Coupling
40R Repair Coupling
40R Coupling
General Information
40R Coupling
Dimensions
Code Description A
Guarantee
Fittings
Products are subject to a 25 year guarantee that is between Pegler and the final purchaser of the product.
This guarantee does not affect any statutory rights the consumer may have in law.
The guarantee covers manufacturing or material defects and does not cover parts subject to normal wear
and tear.
This product range has been designed for the use of homeowners, domestic and commercial applications
and therefore the guarantee is subject to the product being properly selected for their intended service
conditions.
The guarantee is not applicable where the product is fitted contrary to the conditions in the fitting
instructions.
Provided it is installed correctly and receives adequate preventative maintenance it should give years of
trouble –free service.
Abusive behaviour and accidental damage to the product are not covered by this guarantee.
The extent of this liability is limited to the cost of the replacement of the defective item and not to fitting or
consequential damages.
Care
This product does not require any regular aesthetic care.
Maintenance
No maintenance is required for this product; if possible a visual inspection can be undertaken for any
accidental knocks. Do not attempt to over tighten as this will not produce a better joint.
For any further maintenance issues please contact your local qualified installer.
If your product is under warranty please contact the Service Support Team on: 0800 1560050.
Regulations
Regulations
It is important to ensure that the water supplies to your waste are connected in accordance with the water
regulations (WRAS) requirements and good plumbing practice.
This product complies to EN1254 and the kitemark standard and is documented in the WRAS Water fittings
directory.
Materials
Component Material
Body Brass Bar
Capnut Forged Brass
Cone Brass
40R Coupling Spare Description Code Barcode Date From Date To Price (£) ex
Key VAT
Spare Key Description Code Barcode Date From Date To Price (£) ex VAT
Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF
Telephone: Phone +44 (0) 844 243 4400 Fax: +44 (0) 844 243 9870 Website: www.pegleryorkshire.co.uk
Registered office : Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF Company no : 00401507
Prestex
installation instructions
Working Temperatures and Pressures general specification
Service Temp
Medium up to ºC Maximum working pressure Manufactured to EN 1254 (formerly
BS 864/2), and carrying the
Bar PSI
prestigious Kite mark, Prestex ‘Type
Water or light mineral oils 30 16 232 A’ compression fittings are suitable
8mm to 54mm
65 10 145 for mechanically joining copper or
110 6 87 stainless steel tube by means of
120 5 72 compressing a cone onto the tube
Compressed Air non-shock 30 7 100 without the application of heat.
8mm to 28mm size only
Saturated steam 120 3 43 The range is designed for use with
LPB 3 to 28mm sizes only 30 1 15 copper tube to BS EN 1057:1996
Natural Gas 60 5 73 (formerly BS 2871:Part 1), BS
Note: Chromium plated Type A compression fittings comply with the same criteria as un-plated fittings. 2871:Part 2, or stainless steel tube to
BS 4127:1994. Fittings are available in
a brass bodies, all with brass capnuts
how to make a 'type A' joint 3. In both cases,
as standard. Sizes range from 8mm
tighten the capnut
up to 54mm, covering a wide range
1. Ensure that the fitting is the correct onto the fitting
of product alternatives including
size for the pipe being used. Cut until the pipe
straights, elbows, tees, crosses and
the pipe to length, making sure that cannot be rotated
reducers to cope with all installation
the cut is square and the pipe is not by hand. A drop of
requirements.
deformed. Remove any burrs from light machine oil
the cut ends. on the threads will
facilitate tightening (particularly on
either larger sizes).
2a. Insert the pipe into the fitting
without removing the capnut and 4. Tighten the
cone, ensuring that capnut with a
the cone is in the good, well-fitting
correct position spanner, using the
and that the pipe table below as a
makes firm contact guideline taking
with the stop in the into consideration
body of the fitting. any variations in
installation conditions.
or
2b. Unscrew the exposure table
capnut and cone Nominal pipe size Number of turns
from the fitting.
8mm 3/4 to 1
Slide the capnut
10mm 3/4 to 1
and cone onto the
12mm 3/4 to 1
pipe, and insert the
15mm 3/4 to 1
pipe into the fitting
18mm 3/4 to 1
as far as the stop.
22mm 3/4 to 1
28mm 3/4 to 1
35mm 1 to 1 1/4
42mm 1 to 1 1/4
54mm 1 to 1 1/4
Notes
further details
www.pegler.co.uk
Kitemark™ Certificate
Kitemark™ Certificate
No. KM 07082
In respect of:
This issues the right and licence to use the Kitemark in accordance with the Kitemark Terms and Conditions
governing the use of the Kitemark, as may be updated from time to time by BSI Assurance UK Ltd (the "Conditions").
All defined terms in this Certificate shall have the same meaning as in the Conditions.
The use of the Kitemark is authorized in respect of the Product(s) detailed on this Certificate provided at or from the
above address.
For and on behalf of BSI: Chris Lewis - Certification Director, Product Certification
Page: 1 of 3
Page: 1 of 3
This certificate has been issued by and remains the property of BSI Assurance UK Ltd, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP, United
Kingdom and should be returned immediately upon request.
To check its validity telephone +44 (0) 345 080 9000. An electronic certificate can be authenticated online.
BSI Assurance UK Limited, registered in England under number 7805321 at 389 Chiswick High Road, London W4 4AL, UK.
A member of BSI Group of Companies.
Kitemark™ Certificate
No. KM 07082
Page: 2 of 3
This certificate has been issued by and remains the property of BSI Assurance UK Ltd, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP, United
Kingdom and should be returned immediately upon request.
To check its validity telephone +44 (0) 345 080 9000. An electronic certificate can be authenticated online.
BSI Assurance UK Limited, registered in England under number 7805321 at 389 Chiswick High Road, London W4 4AL, UK.
A member of BSI Group of Companies.
Kitemark™ Certificate
No. KM 07082
Page: 3 of 3
This certificate has been issued by and remains the property of BSI Assurance UK Ltd, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP, United
Kingdom and should be returned immediately upon request.
To check its validity telephone +44 (0) 345 080 9000. An electronic certificate can be authenticated online.
BSI Assurance UK Limited, registered in England under number 7805321 at 389 Chiswick High Road, London W4 4AL, UK.
A member of BSI Group of Companies.