Professional Documents
Culture Documents
07 Vetonit Base WR - Group 180821
07 Vetonit Base WR - Group 180821
07 Vetonit Base WR - Group 180821
Vetonit Base WR
Weather resistant premix cement
coating for internal use
Uses
u It can be applied internally onto walls & ceiling
surfaces.
u On concrete surfaces that are smooth and also
on precast concrete surfaces.
u On wall surfaces that are plastered with water-
resistant plasters, Vetonit Renders, and on
damp concrete interiors.
Product Description
Vetonit Base WR is a cement-based coating composed of hydraulic binders, selected aggregates, and special
additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which required only the addition
of clean water to produce easily workable mortar. Vetonit Base WR is a high-quality product for multipurpose use and
a base coat for Vetonit Finish WR. Vetonit Base WR can be applied in thickness from 1 mm to 5 mm, in one or two
layers depending on the on-site requirement. Vetonit Base WR is available in two standard colors white, Grey & Saveto
standard colors.
Technical Data
Advantages Vetonit Base WR Typical Values @ 25ºC
u Factory controlled pre-blend ensures White, Grey & colored
Appearance
Base WR
consistently high quality. Powder
Maximum Aggregate Size Up to 0.72 mm
u Requires only the addition of water on-site at
the time of usage. Wet Density 1.45 Kg/Liter
Application Thickness 1 to 5 mm
u Manual or spray machine application. Pot Life 1 Hour
u Superior workability. Setting Time 5 - 7 hours
Cleaning
Usage Instructions
Clean all tools with water immediately after finishing.
Surface Preparation Clean hardened materials mechanically.
The surface should be sound, clean free from loose
The surface should be sound, clean, free from loose Packaging & Coverage
material, grease, laitance, dirt curing compound, etc.
Product Pack Size Yield
Before the Vetonit Base WR application, wet the entire 25 Kg Bag or 1.0 - 1.2 Kg /m2 /
surfaces with clean potable water, and the surface Vetonit Base WR
Bulk 1mm thickness
should look damp at the time of the Vetonit Base WR
application. Stated consumption data are for general guidance.
Actual value depends on the nature of the substrate,
Mixing method of application & wastages.
Internal Block Walls & Rough Surfaces Shelf Life & Storage
For manual application, add to the mixing container The original sealed bag of Vetonit Base WR has a shelf
7.5-8.5 liters of water for each 25 Kg bag of Vetonit Base life of 12 months provided it is stored clear of ground in
WR. For the Spray machine application, use 9.5-10.0 a dry and shaded place.
liters of water for each 25 kg bag. Add the powder to
the water and mix with a mechanical mixer, or use a Limitations
low-speed electric drill fitted with a suitable paddle.
Do not mix with any additives or products unless
Mix for 3-4 minutes until achieving a uniform, lump-
recommended by Saveto.
free consistency. Allow the mixed material to stand for
about 10 minutes, and remix briefly without adding Make sure the substrate is suitable for the plaster coat
further water. application. In case of doubt, try on the sample area to
assess its suitability.
Smooth Concrete Surfaces
Do not apply the product at a temperature of less
Add 0.5 liters of Vetonit Bond 2 to the mixing water and than +5ºC. During the summer season, the working
adjust the water requirement accordingly for each 25 area must be covered to prevent ill-effects from direct
kg bag. Follow the same mixing procedure as described sun and excessive air-draught during the initial curing
above. stage.
Base WR
Use the mixed material within 4 hours. Do not add water For further information contact our technical
to the mix once the mixed mortar starts to harden.. department.
Application
Apply Vetonit Base WR to achieve a maximum thickness Health & Safety
of 5 mm in layers, 1-2 mm per layer. Vetonit Base WR is highly alkaline; therefore, avoid
direct contact with eyes or skin. It is recommended to
Technical Data Sheet -Vetonit
LEGAL DISCLAIMER
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any
liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how
its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the
right to change any of the Technical Data Sheets specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and
new 3rd party testing; kindly refer to our website for the latest updated TDSs.