Professional Documents
Culture Documents
Engineering Graphics and Design 2/2 Grade 10 TASK 4.2 June Examination 2021
Engineering Graphics and Design 2/2 Grade 10 TASK 4.2 June Examination 2021
GRADE 10
TASK 4.2
INVIGILATOR INSTRUCTIONS
• The approved invigilator downloads the unique barcoded cover page from my.Impaq, signs it and attaches it to the front of the answer sheet for
marking purposes.
• The examination answer sheet and unique barcoded cover page must be submitted on my.Impaq for marking purposes, with the exception of EGD,
Dramatic/Visual Arts and CAT Practical*, where the invigilator/courier must submit a hard copy at Impaq’s offices by hand. *Practical papers must be
submitted by CD/flash drive.
• A copy of the answer sheet must be kept for any hard copy submissions.
Page 1 of 6 © Impaq
June Examination 2021
G10 ~ Engineering Graphics and Design P2/2
INSTRUCTIONS
NAME AND SURNAME
1. This paper consists of a cover page and FOUR sheets.
STUDENT
2. There are FOUR questions. Answer all the questions on the drawing sheets provided.
NUMBER
3. Plan your time carefully.
MARKS
4. Write your name in print in the title block on each drawing sheet. MARKS
ACHIEVED
5. Draw neatly and accurately.
6. Use your own discretion where dimensions or detail have been omitted. Question 1 21
7. All drawings must be drawn on a scale of 1:1, unless otherwise stated.
8. All the drawing sheets must be stapled in the correct order and submitted, irrespective Question 2 25
of whether the question was answered or not.
Question 3 24
Question 4 30
TOTAL 100
Page 2 of 6 © Impaq
QUESTION 1: ANALYTICAL (MECHANICAL)
Given
A cast drawing showing three views of a CLAMP ARM, a title block and a table of
questions. The drawing have not been prepared to the indicated scale.
Instructions
Complete the table below by neatly answering the questions, which refer to the
M10 85 accompanying drawing and the title block. [21]
A
QUESTION ANSWER MARK Mark MOD
achieved
32
B
6
Ø32
28 2 2. On what date was the drawing completed?
D
F 4. Who drew the drawing?
M
40
N 5. On which date was the drawing drawn?
6
R12
Ø18 7. What orthographic system has been used?
13
Q
E
26
M10 8. Determine the sizes at A, B, C, D, E and F. A: B: C:
R12 D: E: F:
Q:
R:
MATERIAL:
# REQUIRED
CAST IRON
25
INSTRUCTIONS:
Answer the question by doing the activities
step-by-step:
C D
ASSESMENT RUBRIC
MARK Mark achieved MOD
1. ELLIPSE 6
2. ISOSCELES TRIANGLE 2
3. HEXAGON 2
4. PENTAGON 7
5. CIRCUMSCRIBED CIRCLE 3
6. INSCRIBED CIRCLE 3
7. LINE DIVISION 2
TOTAL 25
80
14
A
AF60
60
24
14
8
A
30
50
A ASSESMENT RUBRIC
MARK Mark achieved MOD
1 Auxiliray view &
placement 3
2 Isometric 14
3 Hexagon 7
TOTAL 24
STUDENTNUMBER/NAME : ENGINEERING GRAPHICS AND DESIGN IMPAQ 2021
Given:
Details of a PULLEY SUPPORT with section B-B.
Instructions:
Draw to a scale of 1:1 and in third angle orthographic
projection the following views.
HOLE Ø14
B
R12
4 X BOSSES Ø20
HEIGHT 4
4 X HOLES Ø 10
R18
HOLE Ø10
B A
R14
ASSESMENT RUBRIC
MARK Mark achieved MOD
1. Front view 12
2. Left view 111
2
3. Centerlines 31
2
4. Section B-B 3
TOTAL 30
STUDENTNUMBER/NAME : ENGINEERING GRAPHICS AND DESIGN IMPAQ 2021