Professional Documents
Culture Documents
Decade Da 1002, Decade Da 3504, Decade Da 4002, Decade Da 6502 JBL Om
Decade Da 1002, Decade Da 3504, Decade Da 4002, Decade Da 6502 JBL Om
D E C A D E ™
A M P L I F I E R S D A 4 0 0 2 , D A 6 5 0 2 , D A 3 5 0 4 , D A 1 0 0 2
G E N U IN E JB L
DA OM 7/14/98 11:38 AM Page 2
2
DA OM 7/14/98 11:38 AM Page 3
1 7 9 6 8 6
8
2
2 1 7 9 7 1 2
5 4
3 3 5
4
20
20 AMP
+ LEFT – – RIGHT +
30
SPEAKER OUTPUT POWER
SPEAKER OUTPUT
DA4002/DA6502
DA3504
2 1 7 9 8
Controls and Connectors
1. Pre-amp Line Level Input Connector –
Connects to line-level output from the 5. Power Connector – Connection for SPEAKER INPUT LINE INPUT INPUT LEVEL BASS EQ LOW PASS
FILTER
L
+
–
R+
R–
R
L
L R
speaker level output from the source 7. Input-Level Control – Adjusts input sen-
unit (2-channel on DA4002, DA6502, sitivity for pre-amp level and speaker 5
3 4
DA1002; 2 separate 2-channel connec- level inputs.
tors on DA3504). 8. Crossover Selector – Determines
20 AMP
3. Speaker-Output Connector – 2-channel whether the crossover is a High-Pass SPEAKER OUTPUT POWER FUSE
– BRIDGED +
on DA4002, DA6502 and DA1002; 4- filter @120Hz (HP), a Low-Pass filter + LEFT – – RIGHT + REM GND(–) BATT(+) 20 AMP 20 AMP
20
20
4. Fuse – DA4002: 15A ATC, pass filter frequency selector (DA1002).
DA6502: 20A ATC, DA1002 2x 20A ATC, 9. Bass E.Q. – Enables bass boost +6dB
DA3504: 30A ATC. @ 50Hz. DA1002
3
DA OM 7/14/98 11:38 AM Page 4
4
DA OM 7/14/98 11:38 AM Page 5
5
DA OM 7/14/98 11:38 AM Page 6
Figure 1
L – R – R
15
15 AMP OFF +6dB LPF FLAT HPF
+ LEFT – – RIGHT + 1 10
L
SPEAKER OUTPUT POWER
Figure 2
Applications
For your convenience, we’ve included
several application diagrams to help you 20 AMP
L + R+
INPUT LEVEL BASS EQ LOW PASS
FILTER
20
20
OFF +6dB OFF 70Hz 100Hz
1 10
+ +
ure the Decade Series power amplifiers –
L R
–
L
20
20 AMP 1 10
R
–
L
+
R
– – – –
2-way speakers with the two front MONO STEREO
30
OFF +6dB LPF HPF LPF HPF OFF +6dB
STEREO 1 10 1 10
MONO
FLAT FLAT
L L
6
DA OM 7/14/98 11:38 AM Page 7
Troubleshooting
Use the following guide to identify
symptoms and solve problems. Make
sure the vehicle’s electrical system is
working properly and power is reaching
the amplifier’s power connector.
Declaration of Conformity
Symptom Likely Cause Solution
No audio Low/no remote on voltage Check connections; turn-test turn-on voltage
Speakers are not connected Check wiring; use VOM/DVM to measure speaker coil
or are blown resistance
We, JBL Europe A/S
Kongevejen 194B
Distorted audio Input sensitivity is not set properly See Setting Input Sensitivity on page 5 DK-3460 Birkerød
DENMARK
Audio lacks “punch” Speakers are wired with Check polarity of connections; refer to Applications declare in own responsibility, that the products described
wrong polarity in this owner’s manual are in compliance with technical
standard:
Audio cycles off and on; A protection circuit is turning Verify the following: off electrical system is between EN 55 020/6.1988
amber protection LED amplifier off and on 5 ~ 18 Vdc; temperature is not over 194°F (90°C);
(JBL badge on top panel) no short circuits; speaker loads are not less than 2 ohms
is not lit (4 ohms in mono)
Audio cycles off and on; GAIN is set too high Set Input Sensitivity correctly (see page 5)
amber protection LED
(JBL badge on top panel) is not lit
Steen Michaelsen
JBL Europe A/S
Fuse blows Incorrect wiring or Check connections; refer to Applications Birkerød. DENMARK. 3/98
short circuit
7
DA OM 7/14/98 11:38 AM Page 8
Specifications
DA4002, DA6502, DA1002, DA3504