Professional Documents
Culture Documents
HorseRace KE
HorseRace KE
SPOrts Timing
HORSE RACE
Gallop and Trotting
V1510-1
COMPANY INFORMATION
ALGE-TIMING has successfully been producing electronic timing systems for decades. Long-
time experience, constant development and research are the basis for this success.
The company was founded in 1946 and has been specialized in sports timing since the sev-
enties. ALGE-TIMING is a family-owned company in third generation. Six technicians of a total
staff of about 20 people work permanently in development and research.
The products are distributed by independent sales partners in more than 40 countries world-
wide.
ALGE-TIMING offers a complete range of timing products and display boards. Small private
clubs, communities, stadium builders or timing professionals receive competent consulting
and solutions for their requirements from one supplier.
-2-
www.alge-timing.com
HORSE RACE
ALGE-TIMING is the ideal partner for furnishing horse race courses (thoroughbred and harness racing) with timing and display
technology.
For the equipment with photofinish, photocells, impulse transmission by radio, display boards or videowalls, ALGE-TIMING can
draw upon many years of experience with installations in all parts of the world.
The horse race tracks have one or more tracks. The OPTIc2 is able to connect and control with the Distribution Box OCD2 up
to three photofinish cameras.
On the following pages we will give a review on the system(s) that ALGE-TIMING offers for horse race stadiums.
Photofinish pictures
by OPTIc2
left: thoroughbred
right: trotting
-3-
www.alge-timing.com
HORSE RACE
Example for a system with two tracks
Below you find a diagram as example for a horse race course. Every stadium is built differently and has its peculiarity. Please
contact your local ALGE representative about the optimal system for your horse race course.
ALGE-TIMING
Photofinish
Cameras OPTIc2n
Mirror for
Photofinish
Mirror for
Teledata TED-TX
Photofinish
Finish
Sand
Teledata TED-TX
Photocell Teledata
PR1a-d Finish TED-RX
Grass
Startgate
with Photocell
Closing PR1a-d
Contact
er
ow
t
e
ba
er
al
y
arg
-p
tic
w
ad
C
po
ch
op
re
lo
OPTIc2
Distribution Box
OCD2
Startgate
with Distribution Box
Closing OCD2
Contact
5
PC for Photofinish OPTIc2
2
Color Printer
-4-
www.alge-timing.com
HORSE RACE
Accessories
Photocell PR1a-d:
Photocell with transmitter and receiver for large dis-
tances (up to over 100m).
Photocell PR1a-d
Photocell Casing PB4:
For protection of the photocell against dirt, dust and
weather.
Teledata TED
Photofinish OPTIc2:
The Photofinish records the finish so that the ran- Photofinish OPTIc2
king of the horses can be verified.
-5-
www.alge-timing.com
PHOTOFINISH
OPTIc2n
The ALGE OPTIc2n is the next generation of the successful photofinish system OPTIc. The camera uses the latest CCD line
scanning sensor technology. This allows using the camera even at bad light conditions. High recording speed with up to 3,000
lines per second and high resolution of up to 1360 pixel.
The OPTIc2n is a computerized color photofinish system with integrated evaluation software. The color line scanning camera
scans every movement at the finish line in true color (24 bit, 16.8 million colors) and stores the data on the hard disk of the com-
puter. The stored picture can be displayed on the monitor or can be printed at any time.
-6-
www.alge-timing.com
PHOTOFINISH
OPTIc2n
For which sports is the OPTIc2n sensible?
-7-
www.alge-timing.com
PHOTOFINISH
OPTIc2n
Integrated Evaluation Result Lists
The OPTIc2Net software includes different ways of trans- • Start list
ferring the time from the picture into the result list: • Result list sorted by rank
• Result list sorted by lane
Manual Identification: • Result list sorted by start number
Mark the competitor in the result list. Move the time line with the
mouse to the point where you want to read the time and press Flexible Result Lists:
the right mouse button. The time automatically moves to the • It is possible to select, name and sort headers and to se-
selected competitor in the result list. lect the length of the text field for the header.
• The lists can be printed including the photofinish picture.
Lane Identification: • The software can calculate the following headers:
Mark all lanes before the race starts. For the results of an indi- average speed, delta time, horse distance.
vidual competitor, move the time line to the correct lane. Press ŸIf a competitor has no time in the result list, it is possible
the right mouse button and the time for that competitor is auto- to select the reason for this in a pull down menu.
matically recorded in the result list. ŸIt is possible to write free text in the list
• It is possible to add header and footer to the lists.
Start Number Identification:
Move the time line to the point to where you want to time an indi-
vidual competitor. Press the right mouse button. A small wind-
ow opens, where you have to input the ID number of the com-
petitor. That time moves automatically into the result list.
Electronic Headset
Startgun HS3-2
4 x BANG SPK e-START
Speaker StartUnit
BANG CW SU3
Radio-
Push Button
WTN-PB
WTN-WS
for Radio
False Start WTN-WS
ALGE-TIMING
Display Board
D-LINE
Windspeed
WS2
ALGE-TIMING
Timy3 W for
1 2 3 4 5 6 7 8 Windspeed
PC for Photofinish
Photocell RLS3c
-8-
www.alge-timing.com
PHOTOFINISH
OPTIc2n
Technical Data
Camera OPTIc2n
Sensor: 3 x 1360 pixel (RGB)
Pixel Resolution: max. 1360 pixel per lane
Number of Colours: 16.8 million colors or black/white
Scan Rate: 100 to 3000 lines per second
Recording Time: unlimited; depends on PC hardware
Lens: C-Mount lens adapter - option: Nikon lens adapter
Quartz Frequency: TCXO 20,000 MHz (temperature compensated quartz oscillator)
Measuring Range: 23 hours, 59 minutes, 59.999 seconds
Frequency Deviation:
Temperature: +/- 2.5 ppm at -10°C to +70°C (14°F to 158°F)
(+/- 0.009 seconds per hour)
Ageing: +/- 1 ppm per year
Frequency Adjustment: +/- 0.1 ppm at 25°C (77°F)
Connections: 2 x start input (banana socket)
1 x finish input (banana socket)
2 x finish input (DIN socket)
1 x display board (banana socket)
1 x motor zoom
1 x IEEE 1394a 6 pin
1 x GOF (LC duplex glass optical fibre connector)
1 x CAT5e cable with RJ45 plug
1 x power supply
Power Supply: + 9 - 36 VDC
Temperature Range: 0°C to 50°C (90°F to 122°F)
Accessories:
ALGE-TIMING offers a wide range of accessories for the photofinish camera. Below, we list only the most important ones.
Please contact your local ALGE dealer for more information.
Different Lenses for Camera: Wide range of zoom lenses (manually and electronically controlled) and fix lenses.
IEEE1394 Camera Cables: Wide range of IEEE1394 cables (up to 10 m) and repeater cables (up to 30 m).
Optical Cables: Wide range of optical cables and cable reels with optical cables.
IEEE1394 Interfaces: Wide range of 1394 interfaces for desktop PC or notebook.
Distribution Box OCD2: Connection box for OPTIc2 if the camera is not reachable or far from the PC operator.
Tripod Triman: To mount the camera (maximum height 2.4 m, in addition a gearhead is necessary).
Manual Gearhead 410: Three-dimensional gearhead to adjust the camera exactly to the finish line.
Electronic Gearhead 410E: Electronically controlled three-dimensional gearhead to adjust the camera exactly to the fin-
ish line; no additional wiring necessary; controlled by the OPTIc2 software of the PC.
Weather Protection Case: Protects the camera if used outside in bad weather.
Battery Backup for Camera: Battery device BB1 with integrated 12 VDC battery and charger.
-9-
www.alge-timing.com
PHOTOFINISH
Software OPTIc2NET
ALGE-TIMING offers with the OPTIc2 a photofinish camera that features the highest standard. The recording time of the
OPTIc2 is only limited by the size of the hard disk of the PC. This is possible because the IEEE1394 connection guarantees a
real time data transmission from the camera to the PC. An Ethernet or USB connection cannot guarantee a data transmission
in real time.
With the software OPTIc2NET it is possible to use all advantages of the OPTIc2 photofinish system. OPTIc2NET is
programmed in the modern program language called .NET which allows the operator to use a flexible screen layout, which
means he can build the layout according to his needs.
The OPTIc2NET software allows to connect and operate all ALGE-TIMING photofinish accessories like Distribution Box OCD2,
remote control zoom lens, remote gear head and IDCam (high resolution webcam).
-10-
www.alge-timing.com
PHOTOFINISH
Software OPTIc2NET
Synchronization of the System:
It is possible to synchronize the OPTIc2 camera with the PC or other timing devices.
Timing:
Once the system is started all timing impulses are stored in an impulse list. Each impulse is marked with date, time of day, timing channel,
type of impulse (e.g. start) image and ID-number.
Never Miss a Start Impulse again:
The fact that all timing impulses are stored allows the operator to correct times. This feature is very
important for the start. At the start it can happen that the starter does not take care and starts a race
without the approval of the timing operator. In this case, the start impulse is stored in the impulse list
and the operator can use the time from the timing list as official start time. This is possible during the
race.
-11-
www.alge-timing.com
PHOTOFINISH
Software OPTIc2NET
Integrated Results Software:
The OPTIc2NET includes a universal and flexible results software to print start lists, results lists including the photofinish picture of a heat, or
photofinish pictures. The data of the competitors can be imported e.g. from Excel or other meet manager systems. After evaluating the
photofinish picture it is possible to print the results list. Many sports are supported like athletics, cycling, rowing, horse racing, greyhound
races, short track races, cross county, etc.
Ÿ The headers of the list columns are selectable. The order of columns and column width are adjustable.
Ÿ It is possible to import sponsor logos in the header and/or footer.
Ÿ Two separate text fields allow the operator to insert a free text.
Ÿ Possibility to print the photofinish picture or important parts of the picture in the results list.
Ÿ Possibility to print the photofinish picture or important parts of the picture.
Ÿ Classes are possible in the results list (e.g. women and men with separate ranking).
Ÿ The data import from Excel is possible.
Ÿ The export of a list in pdf-format is possible.
Result List for Cycling Result List for Track and Field
-12-
www.alge-timing.com
PHOTOFINISH
Software OPTIc2NET
Examples of Pictures from the Photofinish OPTIc2NET
-13-
www.alge-timing.com
PHOTOFINISH
Distribution Box OCD2
If your photofinish camera is positioned far from the operator you can connect the external devices (e.g. start device,
finish photocell) to the Distribution Box OCD2 next to the operator.
ge
ba
er
al
y
Indoor Arena
-p
tic
w
ad
ar
w
AC
po
ch
op
re
lo
BB1
Camera for OPTIc2
Distribution Box
OCD2
200 m Track
Photofinish
OPTIc2n Notebook for OPTIc2
Camera for
60 m Track
Photocell RLS3c 100 - 240 VAC
Display Board D-LINE
ALGE-TIMING
1 2 3 4 5 6
Headset
1 HS3-2
1 2 3 4 5 6 7 8
Headset
1 HS3-2
Electronic
Elec
Startgun
S
e-Start
StartUnit
BANG SU3
-14-
www.alge-timing.com
PHOTOFINISH
Distribution Box OCD2
Technical Data
Quartz Frequency: TCXO 20.000 MHz (temperature compensated quartz
oscillator)
Measuring Range: 23 hours, 59 min., 59.999 sec.
Frequency Deviation: Temperature: +/- 2.5 ppm at -10°C to +70°C (14°F to 158°F)
(+/- 0.009 seconds per hour)
Ageing: +/- 1 ppm per year
Frequency Adjustment : +/- 0.1 ppm at 25°C
Internal Battery: lead battery 12 V / 2,2 Ah
Power Supply: +9 - 15 VDC
Temperature Range: 0°C to 50°C (32°F to 122°F)
Connections: 3 x start input (banana socket)
3 x finish input (banana socket)
3 x finish input (DIN socket)
2 x display boards (banana socket)
1 x RS232 – DIN socket
1 x Printer – DIN socket
3 x Photocells – DIN socket
1 x Headset – DIN socket
1 x Windspeed WS2
1 x Camera – IEEE1394a 6 pin bilingual
1 x Camera - GOF (LC duplex glass optical fiber)
1 x Power Supply +9 - 15 VDC
1 x Mains 100 – 240 VAC
ALGE-TIMING
Photofinish
Camera OPTIc2n
Mirror for
Photofinish
Teledata TED-TX
Mirror for
Photofinish
Finish
Teledata TED-TX
Sand
Photocell Teledata
Finish TED-RX
PR1a-d Grass
Startgate
Photocell
with
PR1a-d
Closing Distribution Box
er
ow
t
e
ba
er
al
y
arg
-p
tic
w
ad
C
po
ch
op
re
lo
Contact OCD2
OPTIc2
Distribution Box
OCD2
Startgate
with
Closing
Contact
Printer
PC for Photofinish OPTIc2n
5
2
Photofinish System
for Horse Races
-15-
www.alge-timing.com
PHOTOFINISH
OPTIc2 Accessories
You can obtain from us a wide range of accessories for the photofinish system OPTIc2. For further acces-
sories, that cannot be shown here, please contact us.
-16-
www.alge-timing.com
PHOTOFINISH
OPTIc2 Accessories
Camera Cables and Cable Reels IEEE1394 Interface for PC
If the camera is situated far from 1394PCIe: PCI express card with
the user, mains and/or optical ca- IEEE1394 connections for
ble is required. ALGE-TIMING offers desktop PC
cable and/or cables on reels in dif- 1394EXP: Express card with IEEE
ferent lengths. 1394 connections for note-
book
6 to 6 pin
AA- IEEE1394a
max. 400 mBit/s
6 to 4 pin
AB- IEEE1394a
max. 400 mBit/s
no power supply
6 to 9 pin
AC- IEEE1394b
max. 400 mBit/s
9 to 9 pin
CC- IEEE1394b
max. 800 mBit/s
-17-
www.alge-timing.com
IMPULSE DEVICES
Photocell PR1a
The photocell PR1a is a masterpiece of precision and power with the smallest possible dimensions.
The transmitter of the photocell sends a modulated infrared beam. The receiver checks the infrared beam and triggers an im-
pulse for each interruption.
To use the photocell universally it is possible to switch between three different functions: reflection photocell, photocell trans-
mitter and photocell receiver.
Photocell PR1a:
Ÿ Impulse accuracy of up to 1/10,000 seconds
Ÿ Different functions with one photocell:
Ÿ reflection photocell with reflector
Ÿ separate transmitter unit and receiver unit for long distance use
Ÿ Long distance range
Ÿ reflection photocell about 25 m
Ÿ through-beam photocell over 150 m (500 feet)
Ÿ Variable power supply for the photocell
Ÿ battery operation
Ÿ power supply from ALGE timing device
Ÿ external power supply from 4 to 18 VDC
Ÿ Battery indication with LED (green, yellow, red)
Ÿ Indication of photocell adjustment with LED (green, yellow, red)
Ÿ Synchronisation of two photocells (main and backup) to prevent interference
Ÿ Adjustment of delay time (20 ms to 2 seconds (factory adjustment = 20 ms))
Photocell PR1aW:
The photocell has a built-in radio module (2.4 GHz) and therefore a wireless impulse
transmission is possible. It is compatible with the WTN-series (Wireless Timing
Network). Up to 15 different radio channels and 5 impulse channels are adjustable. Of
course, you can connect the photocell as well by cable with the timing device.
Additional functions:
Ÿ Built in radio module for wireless impulse transmission
Ÿ Impulse transmission by cable is possible
-18-
www.alge-timing.com
IMPULSE DEVICES
Photocell PR1a
Types of Photocells:
Reflection Photocell PR1a-R:
If one photocell is used with a reflector we call it a reflection photocell. The function
of the reflector is like a mirror, which reflects the beam sent from the transmitter
back to the receiver.
Photocell range: about 25 m (80 ft)
Photocell set: 1 x PR1a, 1 x PR1a-REF, 2 x BBG, 1 x 001-10 (10 m/33 ft)
Reflection Photocell PR1a-RT:
Same as PR1a-R but supplied with tripod (instead of fastening bracket BBG) and
30 m (100 ft) photocell cable.
Photocell range: about 25 m (80 ft)
Photocell set: 1 x PR1a, 1 x PR1a-REF, 2 x TRI128, 1 x 001-30 (30 m/100 ft)
Through-Beam Photocell PR1a-d:
The PR1a can be used either as TX or RX unit. It sends an infrared beam from one Reflection Photocell
PR1a set as transmitter to another PR1a set as receiver.
Photocell range: over 150 m (500 ft)
Photocell set: 2 x PR1a, 2 x BBG, 1 x 001-10 (10 m/33 ft)
Through-Beam Photocell PR1a-dT:
Same as PR1a-d but supplied with tripod (instead of fastening console BBG) and
30 m (100 ft) photocell cable.
Photocell range: over 150 m (500 ft)
Photocell set: 2 x PR1a, 2 x TRI128, 1 x 001-30 (30 m/100 ft)
Radio Photocell PR1aW-R (as PR1a-R but with radio):
Photocell range: about 25 m
Photocell set: 1 x PR1aW, 1 x PR1a-REF, 2 x BBG
Through Beam Photocell
Radio Photocell PR1aW-RT (as PR1a-RT but with radio):
Photocell range: about 25 m
Photocell set: 1 x PR1aW, 1 x PR1a-REF, 2 x TRI128
Radio Photocell PR1aW-dT (as PR1a-dT but with radio):
Photocell range: over 150 m
Photocell set: 1 x PR1aW, 1 x PR1a, 2 x TRI128
Technical Data:
Range with reflector: 0.5 to 25 meter
Range with transmitter and receiver: 0 to over 100 meter
Impulse output: NPN transistor, open collector, active low
Reaction time: 300 µs, 1 ms fix adjusted
Impulse length: 20 to 2000 ms (adjustable delay time)
Measurements PR1A (without swivel head): about 118 x 87 x 44 mm
Weight PR1A: about 0.3 kg
Weight PR1a-Ref: about 0.2 kg
Switches: On/Off switch for battery
Three position switch for modes (Norm, TX, RX)
Power supply: from ALGE timer: 5 VDC stabilized
external power supply: 4 - 18 VDC
internal battery: 2 x AA-Battery
Power consumption: from battery with 2,5 VDC: 20 - 46 mA
from timing device 5 Vstab: 9 - 20 mA
Operating hours with internal batteries: measured at 22°C (72°F), with 1 impulse per minute, no radio:
alkaline AA batteries: 77 hours
NiMH AA rechargeable batt.: 70 hours
Additional Data for PR1aW:
Radio frequence: 2,4 GHz band, 16 adjustable teams
Radio power: 10 mW or 10 to 100 mW (adjustable)
Timing channels: 5 different adjustable channels (c0 (start), c1 (finish) c2,c3, c4)
Radio distance: about 350 m at free sight
Additional switches: Rotation switch for team (radio frequency)
Rotation switch for impulse selection (impulse channel)
Weight of PR1aW: about 0,3 kg
Operating hours with internal batteries: measured at 22°C (72°F), with 1 impulse per minute and radio:
alkaline AA batteries: 38 hours
NiMH AA rechargeable batt.: 35 hours
-19-
www.alge-timing.com
IMPULSE DEVICES
Photocell Accessories
Reflectors
Reflector PR1a-REF
Standard reflector for photocell PR1a and PR1aW
Reflector REF-3
Standard reflector for photocell RLS3c
Reflector REF-C
Reflector for photocell with big distances
Reflector REF-L
Simple, inexpensive reflector manly used for
training systems
RR1a-REF REF-3 REF-C REF-L
Case KL-RLS3c
for photocell RLS3c with
accessory
-20-
www.alge-timing.com
ACCESSORIES
Teledata TED400
Impulse Transmission: Safe as never before
The impulses (start or stop impulses) are transformed by a wireless transmitter TED-TX into a data package, provided with a
safety code and transmitted to the receiver TED-RX. After having checked the safety code, the receiver transmits the impulse
to a timing device with an accurate, reproducible delay of 0.1 seconds.
Start Finish
Startgate
-21-
www.alge-timing.com
ACCESSORIES
Teledata TED400
Data transmission: with absolute safety
In the data transmission (e.g. of the Data transmission / time measurement:
start time), the data plus the safety
The start time is transmitted by radio from the timing device to a data collector. Every
code are transmitted from the trans-
second a data set is transmitted. To play it safe every data set is transmitted 10 times.
mitter TED-TX to the receiver TED-
RX. The receiver forwards the data
From timing device at start to the finish:
to a data collector (e.g. PC).
TED-RX
Finish
Photocell
Timing TED-TX
Device
Data transmission / Remote control by timing device:
Every data set is transmitted once. Every 1/10 second a data set can be transmitted:
! from timing device to display board
! from timing device to printer
! from TIMY terminal to display board
Application area:
! timing device to PC
! PC to PC
! PC to display board Data
Receiver
-22-
www.alge-timing.com
ACCESSORIES
Teledata TED400
Technical Data
Output Power: 400 mW (for TED-TX400)
Working Range: up to 5 km
Frequency: 433.800 MHz (standard frequency)
alternatively on request: 434.650 MHz, 433.200 MHz, 433.650 MHz
Interfaces: TED-TX400: RS232 (input)
TED-RX400: RS232 (output) and RS485 (output)
Power Consumption: TED-TX400: 270 hours with one impulse per minute
TED-RX400: 54 hours with one impulse per minute
Antenna: short, tough, flexible
Connections: compatible with ALGE products and most others
Ÿ Banana socket for data and start impulse
Ÿ DIN socket with connection for start and stop impulse, data and external supply
Input Signal: closing contact, active low, min. 10 ms
Output Signal: transistor, open collector, active low, 100 ms
LED: for battery indication (TED-TX and TED-RX),
and moreover for field intensity indication in the TED-RX
Loudspeaker: in the TED-RX for field intensity indication and interface evaluation
Power Supply: internal: Ÿ 6 x AA – Alkaline batteries or
Ÿ 6 x AA – NiMH rechargeable batteries
external: Ÿ Charger PS12 or from timing device
Operating Temperature: -20° to +50°C / -4°F to 122FF
Dimensions: 198 x72 x 72 mm (without antenna)
Fastening: Velcro fastener for pole fixation, thread for tripod or flange support for photocell
Accessory: Ÿ Case with foam insert for safe transport
Ÿ Rechargeable battery set with six NiMH batteries for TED
Ÿ Charger LG6AA for six NiMH rechargeable batteries
Ÿ Channel extension RX-C10
Ÿ Holder to set up a TED and photocell at one tripod or fastening console
IMPORTANT:
The regulations for radios are very different all over the world. Please check if you can use the radio legally in the country that you want to
operate it in. In some countries you may not use it or you have to register it.
START
TED-TX400
Startgate
STSn1MS
Teledata
TED-TX
Finish
Photocell PR1a-RT
Teledata TED-TX
or PR1a-dT
Teledata
TED-TX
Start
Photocell
Timing System PR1a-RT
or PR1a-dT
Finish Jump Off
Photocell PR1a-RT
ALGE-TIMING
Timeout
Push Button Speaker
023-10 DL StNo
ALGE-TIMING
RANG
TED-RX400
PUNKTE
ALGE-TIMING
Start-Stop
Switch 129-06
129-06 ZEIT
-23-
www.alge-timing.com
HORSE RACE
Display Boards
ALGE-TIMING offers different display boards for riding. The model shown below is a solution that has been installed on many
horse race courses worldwide. It has proved itself by its convenience and clarity. Of course, ALGE-TIMING also offers full matrix
display boards as well as videowalls.
We are also glad to work together with our customers on special solutions for the particular race track. Please ask your local
ALGE representative!
-24-
www.alge-timing.com
HORSE RACE
Display Boards
-25-
www.alge-timing.com
DISPLAY BOARD
D-LINE
The ALGE D-LINE series is a very versatile numeric display board. It is possible to control it directly from
ALGE timing devices as well as from other devices by RS 232 interface.
Additionally, it is possible to show the time of day or use it as simple stand alone stopwatch or count-
down device. If a DCF or GPS radio receiver and a temperature sensor is purchased with the LED dis-
play board, the run-time is shown during a sports event and at all other times the board shows alterna-
tively time and/or temperature.
ALGE offers models for indoor and outdoor. The difference lies mainly in the type of LED used. For out-
door purposes the LEDs must be a lot brighter especially if the sun shines directly on the board.
The standard model has six digits. Of course, we also offer other configurations.
The advantage of LED display boards compared to other display boards is the affordable price and low
weight. Moreover, it is possible to use the board also in dark areas (e. g. under dark roof of a stadium).
The power for the board is supplied either by mains (100-240 VAC) or an external 12 V car battery.
-26-
www.alge-timing.com
DISPLAY BOARD
D-LINE
Technical Data:
Ÿ LED numeric 7-segment figures with 3 points between the figures
Ÿ Internal clock
Ÿ Connections:
Ÿ Banana socket for data (RS 232c)
Ÿ Banana socket for external push button
Ÿ Amphenol socket (4-pin) for data or power supply (12 VDC)
Ÿ Integrated power supply (100 - 240 VAC, 50-60 Hz) Digits with 450 mm figure height
Ÿ Fastening:
Ÿ 2 hangers at the top
Ÿ 3/8 “ thread for tripod
Number Distance
Figure Power Reading
of Height Width Depth between
Height Consumption Distance
Digits hangers
[mm] [W] [m]
Indoor Models:
D-LINE57-I-6-E0 6 57 130 500 60 200 13 25
D-LINE100-I-6-E0 6 100 180 800 60 500 13 50
Outdoor Models:
D-LINE80-O-6-E0 6 80 150 600 60 300 13 40
D-LINE150-O-6-E0 6 150 250 956 60 556 14 75
D-LINE250-O-6-E0 6 250 350 1493 60 1093 34 125
D-LINE450-O-6-E0 6 450 600 2490 80 2090 88 225
D-LINE600-O-6-E0 6 600 800 3400 70 3000 133 300
D-LINE800-O-6-E0 6 800 1000 4800 70 4400 180 400
D-LINE1000-O-6-E0 6 1000 1400 5700 70 5300 270 500
D-LINE1500-O-6-E0 6 1500 2000 8500 70 8100 510 750
Other configurations than stated above are possible on request!
ALGE-TIMING
Example of the order code:
D-LINE57-I-6-E0
Blanks (empty digit) between the digits D-LINE150-O-6-E0
Number of digits, in this case 6 digits ALGE-TIMING
-27-
www.alge-timing.com
DISPLAY BOARD
LED Matrix D-RTNM
The D-RTNM is a universal single colour LED matrix board. It is usable as timing display board, message board or for adverti-
sement purposes. The display can show online preloaded messages or those from the internal memory. Also small animated
films can be shown on the board. The lightweight rugged aluminium case allows an easy transport of the board.
The outdoor version is excellently readable even at direct sunshine. If used at night or at rainy days, it is possible to select
between 100 different brightness levels to reach the best performance of the display at any light condition.
Driving is non-multiplexed, that means that these displays last longer and glow brighter than standard multiplexed displays.
Further this function is very important e. g. if used during TV broadcast, because the display board does not flicker on the TV
screen.
Options:
· Custom designed models with different pixel resolution on request
· Narrow frames for assembling several D-RTNM
· Models with 7 LEDs per pixel
· Different colors (yellow, green, blue or white)
· Connection for temperature sensor
two D-RTNM with narrow frames
· Connection for DCF or GPS synchronization (exact external time signal)
-28-
www.alge-timing.com
DISPLAY BOARD
LED Matrix D-RTNM
Pixel types:
a a a a
P1 b P3 b P4 b P7
DCF, GPS or b
temperature sensor (all optional)
a + b = 10.0 mm
RS232 interface with a + b = 15.0 mm a = 21.6 mm
12 VDC output a + b = 20.0 mm b = 21.6 mm a = 20.7 mm a = 36.8 mm
b = 25.4 mm b = 46.4 mm
RS485 with 12 VDC output
RS232 input (e.g. timing device) Example of the order code:
Ethernet D-RTNM-P3-16x96-I
Power supply 100 - 240 VAC I = Indoor, O = Outdoor
Horizontal resolution in pixel
Fuse Vertical resolution in pixel
Pixel with 3 LEDs (Alternative: 4 or 7 LEDs)
P3 - Pixel with 3 LEDs, H/V pitch 21.6 / 21.6 mm
For models with narrow frames the plugs are P4 - Pixel with 4 LEDs, H/V pitch 20.7 / 25.4 mm
integrated in the backside of the board! P7 - Pixel with 7 LEDs, H/V pitch 36.8 / 46.4 mm
Product description
-29-
www.alge-timing.com
DISPLAY BOARD
Videowall - LED Matrix
ALGE-TIMING offers a wide range of videowalls for any application. From small dimensions to enormous sizes, from a
pixel pitch of 1.42 mm up to 26.7 mm you will find the right solution for your project. On request we can offer curtain
displays (transparent in front of a building) or curved videowalls (e.g. for buildings). Models especially made for perimeter
advertising are available with stands and protection for the top.
The videowalls offered by ALGE-TIMING can be used for sports applications, as stage display (e.g. music festivals, fairs,
fashion shows), for advertising, etc.
This video wall consists of individual modules, which can be
set up in any order. You can also select between models that
allow the maintenance from the back side or the front side.
Because of quick release couplings it is possible to set it up
in a matter of minutes.
If you use the videowall for sport in combination with timing
equipment from ALGE-TIMING, we guarantee an optimal
interface between the devices.
-30-
www.alge-timing.com
DISPLAY BOARD
Videowall - LED Matrix
768
Setup:
The modules are equipped with „unit positioning guide” posts, connection and
combination devices and a self lock system, which allows a fast and simple setup
of the videowall without any tools. Precise positioning and easy assembly.
Hanging Mode:
Optionally we offer hanging beams special made for the cabinet.
Max. hanging capacity: 20 cabinets high
Flight Cases:
Specially-designed flight cases (optional) guarantee a safe transport and storage
of the modules.
Easy Maintenance:
Modules are modular built and the maintenance is easy and simple.
-31-
www.alge-timing.com
DISPLAY BOARD
Videowall - LED Matrix
LED Matrix Boards are very complex. A lot of specifications influence the price. We would like to give you a short introduction
on different terms that are used for LED Matrix Boards:
Pixel: One pixel is the smallest point you can show with a
Matrix Scoreboard. Any pixel can consist of several
LEDs.
Pitch: Describes the distance from pixel to pixel. In general,
the pitch starts with 4 mm and goes up to 50 mm.
The smaller the pitch, the better the resolution and
the more expensive the board per m².
Pixel Size: The bigger the pixel dimension compared to the
pitch, the sharper the picture (fill grade).
LED/Pixel: Any pixel can consist of one or more LEDs. The
more LEDs per pixel the better the scoreboard. But
the quality also depends on the type of the LEDs. In
our full color LED screens we only use Nichia LEDs
that have the best performance.
Resolution: The resolution is the amount of pixels in vertical
and horizontal order. The higher the resolution, the
better is the quality of the picture or text!
Pixelsharing or virtual pixels: The pixelsharing mode is
using LEDs from adjoining pixels to construct virtual
Refresh rate: The higher the refresh rate the more soft-
pixels. The virtual resolution is four times higher
focused is the picture.
than the physical number of pixels. But the picture
quality of a physical videowall with 16 mm is a lot bet- We have a standard refresh rate of 240 and for the
ter than the one of a 16 mm shared mode! professional series we have a refresh rate of 500.
Luminosity: The luminosity is measured in cd/m² or in Nit Static or Multiplex Driving: The driving method of the LEDs
(Candela per square meter) and is important for the should be static.
brightness of the board. This technical characte- You can test this with a digital camera, just watch the
ristic is also stated in different ways. Some produ- videowall and see if there is a flicker in the picture of
cers quote the luminosity for all colors in maximum the camera.
brightness. Any serious producer specifies the The same happens if a TV camera films the video-
brightness in the white-balanced state. Different co- screen and it is broadcasted on TV.
lored scoreboards need different luminosity for out-
Outdoor: The LEDs are completely sealed with a special sili-
doors.
cone; horizontal louvers are integrated in the LED
1 color 2,000 cd/m² modules to maximize the contrast.
full color 5,000 cd/m² in white-balanced state!! 1 Color: The display features only one color (e. g. red). This
For full color scoreboards it is very important to indi- color can have different shades to create a better pic-
cate the luminosity in white-balanced status. Some ture (e. g. 256 shades, like a black and white picture).
manufacturers state the brightness in all colors with Most of these displays are also able to show animati-
100%. This can result in a brightness of 8,000 cd/m² on files.
but after the board is calibrated (white-balanced) it Video Wall: The display offers LEDs with three different colors
actually means 5,000 cd/m²! in each pixel (RGB – red, green, blue). These colors
Viewing Angle: This is a dimension that is not 100% the can be mixed so it has the complete true color spec-
same for different manufacturers. Some producers trum (68 million colors). Such a board has a video in-
define the maximum angle as before the scoreboard put and it is able to show a TV picture. There are also
gets dark. This is a poor definition! scoreboards available with 10 bit color processing
All serious manufacturers define the half-center which result in 1,073 million colors.
brightness, which means in simple words the angle
where you still have 50 % of the full luminosity!
-32-
www.alge-timing.com
DISPLAY BOARD
Videowall - LED Matrix
Mains
100-240V/50-60Hz
Serial or Ethernet
PREVIEW
VGA
DVI
-33-
www.alge-timing.com
DISPLAY BOARD
Time Temperature Display Board D-SAT
The D-SAT is a multi-functional electronic clock that provides a precise and elegant
time display, using bright LED characters with an unrivalled flexibility of operation for
the most demanding time applications. Indoor and outdoor models are available from
57 mm up to 1500 mm digit height.
Ÿ Models with 57,80 mm digit height for indoor use only.
Ÿ 80, 150, 250, 300, 450, 600, 800, 1000 or 1500 mm digit height for outdoor use.
Ÿ 4 or 6 digits (other configuration possible, e.g. with separate temperature).
Ÿ Standard digit color: red - Option: yellow, green, blue or white.
Ÿ Indoor or outdoor models (outdoor models are readable in direct sunlight).
Ÿ Displays time, date and (optionally) temperature or relative humidity.
Ÿ 2 alarm programs, each program with up to 50 alarm times, relay contact 1A (optional). Alter-
natively displays time, date and temperature with user selectable periods.
Ÿ 12 or 24 hour time display format
Ÿ Time adjustment: push button or external synchronization: DCF, GPS, Ethernet.
Ÿ High precision time by internal real time clock and therefore no need to adjust the time after a
power failure. Stand-alone operation with a typical accuracy of ±4 minutes/year at 25°C.
Ÿ Automatic brightness control for outdoor mounting (optional).
Ÿ Seasonal time correction (summer time - winter time).
Ÿ More clocks can be connected in a system. One clock is master and others are slaves.
Ÿ Average LED life time of 100,000 hours. LED displays are very reliable.
Ÿ Plastified black aluminium case (other colors are possible) for all weather conditions (no oxi-
dation).
Ÿ Surface wall mounting (single-sided models) and ceiling
suspensions (double-sided models), other mounting on Dimensions Dimensions
demand. Digit Thicknes
Ÿ Power supply for 100 to 240 VAC - 50/60 Hz Visibility with 4 Digits with 6 Digits
Model Height in mm
(m) (L x H) (L x H)
(mm) (SS/DS)
Example of order code: in mm in mm
D-SAT250-4-SS-O-M-T-GPS-A D-SAT57 57 28 400 x 130 500 x 130 60 / 110
250 250mm character height D-SAT80 80 40 450 x 150 600 x 150 60 / 110
4 4 digits
SS single sided (DS = double sided) D-SAT100 100 50 600 x 180 800 x 180 60 / 110
O outdoor model (I = indoor model) D-SAT150 150 75 730 x 250 956 x 250 60 / 110
M master mode
T temperature sensor D-SAT250 250 125 1100 x 350 1493 x 350 60 / 110
GPS GPS time synchronization D-SAT300 300 150 1300 x 400 1850 x 400 60 / 110
A alarm output
D-SAT450 450 225 1900 x 600 2490 x 600 80 / 110
Options:
GPS - GPS time synchronization D-SAT600 600 300 2490 x 800 3400 x 800 70 / 110
DCF - Radio time synchronization (usable in middle Europe) D-SAT800 800 400 3300 x 1000 4800 x 1000 70 / 110
ETH - Ethernet LAN time synchronization
A - Alarm output (up to 64 alarms programmable) D-SAT1000 1000 500 3900 x 1400 5700 x 1400 70 / 110
T - Temperature sensor D-SAT1500 1500 750 5800 x 2000 8500 x 2000 70 / 110
RH - Relative humidity sensor
SS …Single Sided DS … Double Sided
LS - Light sensor to control the LED-brightness
RACK
CONTROL BOX 3
PC ETHERNET 3
SWITCH
UTP - CAT 5
Ethernet
communication
-34-
www.alge-timing.com
Notes
-35-
www.alge-timing.com
ALGE-TIMING GmbH
Rotkreuzstrasse 39
A-6890 Lustenau
Austria
Tel: +43-5577-85966
Fax: +43-5577-85966-4
office@alge-timing.com
www.alge-timing.com