Professional Documents
Culture Documents
Manual LD Series v2.1 (PW)
Manual LD Series v2.1 (PW)
Operation Manual
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 2 of 78
GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD.
Sales01@suninelaser.com
www.suninelaser.net
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 3 of 78
CONTENTS
1 INTRODUCTION···················································································································7
2 SAFETY ·····························································································································11
2.2 Hazards·······················································································································12
2.2.1 Laser Hazards ········································································································12
2.2.2 Electrical Safety·······································································································12
2.2.3 Other Hazards ········································································································13
4 INSTALLATION ···················································································································24
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 4 of 78
4.2 Air Cooling ···················································································································24
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 5 of 78
6.8 Text Rounding ···············································································································51
6.12 Marking·····················································································································56
7 MAINTENANCE ··················································································································76
8 TROUBLESHOOTING ·········································································································78
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 6 of 78
1 INTRODUCTION
The manual is a part of the product. Please read these instructions carefully before you install and
operate the SUNINE LD Series Handheld Fiber Laser Marking System. If there are any questions
regarding the contents of this manual, please contact SUNINE LASER.
The manual must be available for developing, installing, uninstalling or using a laser system with a
SUNINE product.
The manual is an integral part of the product, please read this manual carefully before installation and
operation.
This manual introduces how to use the LD series handheld fiber laser marking machine correctly and
safely. Be sure to follow the safety instructions stated in this manual, as well as any local accident
prevention regulations and general safety regulations applicable to the area of use. Before starting to
use this product, please ensure that you have read and fully understood the manual, especially the
section "Safety Information" and the corresponding safety guide.
Please keep and backup this manual properly to avoid loss of the original document. If it is lost, please
contact SUNINE immediately.
This document is copyrighted with all rights reserved. SUNINE and the SUNINE logo are registered
trademarks of Guangzhou Sunine Intelligent Technology Co., Ltd..
The information, figures, tables, specifications, part numbers and schematics contained in this manual
are subject to change without notice. The company makes no warranties or representations, express or
implied, with respect to this document. In no event will SUNINE be liable for any direct, indirect, special,
incidental or consequential damages arising from any defect in its documents.
If you have any questions, please contact SUNINE.
The SUNINE LD Series Handheld Fiber Laser Marking Systems are produced by Guangzhou
Sunine Intelligent Technology Co., Ltd. (herein refer to as SUNINE or SUNINE LASER).
The SUNINE LD Series Handheld Fiber Laser Marking Systems have been developed and
designed for marking on products by using laser radiation.
The laser marking system must only be operated by authorized and specifically trained personnel
who are familiar with and observe the procedures within this manual.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 7 of 78
1.2 Signal Words and Symbols in This Manual
In this manual the following safety symbols have been used to alert the users to the text of the
safety instruction next to it.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 8 of 78
1.4 Shipping Contents
Each LD Series fiber laser marking system shipment contains the following items:
1 ea x Laser Marking Head
1 ea x Control Unit
1 ea x Took Kits and Bolts
1 ea x USB WIFI Adapter
2 ea x Screen Protective Cover
1 ea x USB disk
2 ea x Touch Pencil
4 ea x White Plastic Focal Length Spacer and Connecting Rod
1 ea x Protective Glasses
1 ea x Power Adapter (Battery version only)
1 ea x Power Cable
This is to certify that LD Series Handheld Laser Marking System are guaranteed by SUNINE to
be free of all defects in materials and workmanship for a period of one year from the date of
shipment. The maintenance and service of the product must be performed by professionals of
SUNINE, and no one is allowed to disassemble or repair the machine without permission. The
following situations will cause the product to be out of warranty.
Unauthorized disassembly, modification or repair of this product.
Product damage due to improper handling, operation or cleaning.
Damage caused by exceeding the laser power threshold.
The product warranty label is torn or damaged, or there are obvious signs of disassembly.
Exceeded the warranty period.
1.6.1 Transport
Switch off the laser system before transport and disconnect mains connection!
Please make sure that the supply line connecting marking unit and control unit is not
bent!
Do not use the umbilical to carry the laser system!
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 9 of 78
The laser system is a precision-made
instrument and includes numerous electronic
CAUTION and optical components. Please avoid any
mechanical stress (shock, vibrations, etc.) on
the laser system!
1.6.2 Handling
The equipment must be handling appropriately and carefully.
The control unit is to be specifically protected during assemlbly.
1.6.3 Storage
Store the laser system in a horizontal position and protected against dust and
humidity.
Never expose the laser system or one of its components to direct sunlight!
The following conditions are necessary for operation and storage of the laser
marking system:
Temperature +5°C to +40°C
90% max relative humidity - non-condensing
1.7 Nomenclature
The Model number identifies the specific system, and code designations provide details on the
functions and features included.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 10 of 78
2 SAFETY
This section must be reviewed thoroughly before operating the LD Series Handheld Fiber Laser Marking
Systems. Safety instructions in this manual must be followed carefully.
Every laser system is assigned to a laser class, which must be specified at the output location of
the laser beam.
Class Description
Exposure to this radiation is harmful to the eyes if optical instruments are used
1M to reduce the cross section of the laser beam. If this is not the case, this laser
radiation is not harmful, is eye-safe.
The laser radiation is in the visible spectral range of 400 nm to 700 nm. Short
2
exposure time less than 0.25s are not dangerous to the eyes.
The laser radiation is in the visible spectral range of 400 nm to 700 nm.
Exposure to this radiation is harmful to the eyes if optical instruments are used
2M
to reduce the cross section of the laser beam. If this is not the case, exposure to
this radiation for less than 0.25s is not harmful to the eyes and is eye-safe
3B The laser radiation is dangerous to the eyes and in some case also to the skin.
The laser radiation is very dangerous to the eyes and dangerous to the skin.
4 Stray radiation can also be dangerous. The laser radiation can cause fire and
explosion.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 11 of 78
2.2 Hazards
SUNINE LD Series Handheld Fiber Laser Marking Systems should be installed and
operated by trained personnel only who have been instructed by the laser protection
officer and are sufficiently qualified to perform the laser work. Due to the risks and
hazards associated with the installation and operation of the laser, the operator must
follow product warning labels and instructions to ensure laser safety.
Always wear safety glasses or protective goggles with side shields to reduce the
risk of damage to the eyes when operating the laser.
A fiber laser is an intense energy source and will ignite most materials under the
proper conditions. Never operate the laser near the combustible or explosive
materials, gases, liquids or vapors.
Exposure to direct or diffuse fiber laser radiation can seriously burn human or
animal tissue, which may cause permanent damage. Do not place your body or
any combustible object in the path of the laser beam.
Appropriate protection mechanisms must be used to avoid laser radiation outside
the expected working area.
The SUNINE LD Series Handheld Fiber Laser Marking Systems use AC voltages. The
maximum operating voltage is the connected mains voltage, which to be maintained is
shown on the name plate.
All works at the open laser housing, especially at electrical components, must only be
performed by specially trained personnel!
In the case of a defective power supply, operation of the laser marking system is to be
stopped immediately and is only to be repaired by authorized personnel.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 12 of 78
2.2.3 Other Hazards
The following hazards are typical for this product family when incorporated for intended
use:
Risk of injury when lifting or moving the unit
Risk of exposure to hazardous laser energy through unauthorized removal of
access panels, doors, or protective barriers
Risk of exposure to hazardous laser energy and injury due to failure of personnel to
use proper eye protection and/or failure to adhere to applicable laser safety
procedures
Risk of exposure to hazardous or lethal voltages through unauthorized removal of
covers, doors, or access panels
Generation of hazardous air contaminants that may be noxious, toxic, or even fatal
during laser processing.
2.3 Compliance
SUNINE LD Series Handheld Fiber Laser Marking Systems are designed, tested, and certified to
comply with certain China (CN), United States (U.S.) and European Union (EU) regulations.
These regulations impose product performance requirements related to electromagnetic
compatibility (EMC) and product safety characteristics for industrial equipment.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 13 of 78
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 14 of 78
3 PRODUCT DESCRIPTION
SUNINE LD Series Handheld Fiber Laser Marking System is high performance laser marking
system which developed and produced by the SUNINE professional team based on the years
experience of laser development, production and service.
The laser marking machine contains two parts: laser marking head and control unit.
The control unit is a highly integrated industrial computer system, mainly used in marking
information input, edit and fast and precise control of the laser and galvanometers.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 15 of 78
3.1.2 Laser Marking Head
The laser marking head is connected to the control unit and cannot be removed. The
laser marking head contains the glavo scan head and f-theta lens. The beam is deflected
by the 2-dimension galvanometers and focused by the f-theta lens to the working surface
with appropriate focal length.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 16 of 78
Description: Emergency Stop Switch Alarm
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 17 of 78
Dimensions: Battery Compartment of LD II Series Handheld Laser Marking System
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 18 of 78
3.2 Product Labelling
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 19 of 78
3.3 Technical Information
Max Power
﹤200W ﹤250W ﹤250W ﹤300W ﹤500W
consumption
Overvoltage category II
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 20 of 78
Specification LD20i-B II LD28i-B II LD30i-B II LD50i-B II
At 25-40℃:3.5 hours
Battery run time
At 10-22℃:5.5 hours
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 21 of 78
3.3.2 Mechanical Layout and Dimensions
Dimensions: LD20i II & LD30i II Handheld Fiber Laser Marking Systems (Plug-in & Battery)
Dimensions: LD28i II Handheld Fiber Laser Marking Systems (Plug-in & Battery)
Dimensions: LD50i II Handheld Fiber Laser Marking Systems (Plug-in & Battery)
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 22 of 78
Dimensions: LD100i Handheld Fiber Laser Marking Systems
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 23 of 78
4 INSTALLATION
Before unpacking, inspect the shipping carton for evidence of rough handling, and note any
damage. If you discover shipping damage to the laser, document the damage with a photograph,
then immediately inform the shipping carrier and SUNINE.
After unpacking, review the shipping contents listed in section 1.4 to ensure all components are
received.
Saving all of the laser’s original packaging in case of relocation or shipping .
Protect the laser system and all components from dust and humidity until installation.
SUNINE LD Series Handheld Fiber Laser Marking Systems are cooled by air. The internal
cooling system is designed to supply sufficient cooling.
Make sure that the cooling air can be sucked in and blown out freely and that there is sufficient air
exchange at the installation site to ensure heat dissipation.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 24 of 78
4.3 Placement and Operation
SUNINE LD Series Handheld Fiber Laser Marking Systems design 4 brackets for placement, so
that it can be placed in different postures, which is convenient for users to operate.
For products with a small volume and a height higher than 3mm, if use improper focal length
spacer, the marking plane will be deviated from the focal length, causing the laser to fail to act on
the surface of the product correctly. In order to solve the problem of marking some small products,
LD Series Handheld Fiber Laser Marking Systems provides users with 4 pieces of practical focal
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 25 of 78
length spacers with different size of window. Placing the marking object at the bottom of the
proper spacer will make the laser marking correctly. The specific replacement steps are as follows:
1. Loosen the screws at the bottom of the focusing hood and remove the bottom half;
2. Use the connecting rod to connect focusing hood and the space;
3. Tighten the screw.
SUNINE LD Series Handheld Fiber Laser Marking Systems provides two marking ranges for
users to choose: 50x50mm and 100x100mm. When the other marking field is required, users
need to replace the corresponding focusing hood and field lens.
Refer to section 3.3.2 for the demensions of the focusing hoods. Specific steps of changing the
focusing hood are as follows:
1. Loosen the connecting screw between scan head and the focusing hood, remove the
focusing hood;
2. Unscrew the field lens and replace the field lens with the desired range
3. Replace the corresponding focusing hood and tighten the connecting screws
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 26 of 78
Description: Remove Screws of Focusing Hood
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 27 of 78
5 START-UP AND OPERATION
Before start-up and operation of the laser marking system, carefully check the following:
Check whether the specifications are correct.
Check whether all mechanical installations are complete and correct.
Check whether all electrical connections are complete and correct.
Check whether all optical components are clean and free of dust.
The battery version of the LD Series Handheld Fiber Laser Marking System provides a reset
switch (power button), which can completely disconnect the power supply of the battery to the
system, so as to avoid excessive discharge of the battery and affect the battery lifetime.
1. Press and hold the power button for 5 seconds;
2. The machine will produce a buzzer sounds and the power button light goes off;
3. Release the button and the machine shuts down completely.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 28 of 78
Description: Competely Shutdown Operation of LD Handheld Fiber Laser Marking Systems
Description: How to Remove the Battery from LD Handheld Fiber Laser Marking Systems
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 29 of 78
5.4.2 Charge the Battery
The battery must be taken out to charge to avoid unnecessary risks caused by using the
machine during the charging process. Specific steps are as follows:
1. Open the battery compartment door;
2. Take out the battery;
3. Use the battery adapter to charge.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 30 of 78
5.5 Quick Start Guide
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 31 of 78
5.5.2 Create a New Message
Add New File →Text , click the screen within specific area, and then, select
Click to enter the interface show as below, edit the text and select the
features for the text:
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 32 of 78
5.5.4 Set Properties of the Message
Click on the home screen to set the laser power level, frequency, run
speed and jump speed as need.
Cilck , then click “Start Mark”, press the button on the mark handler, the
marking machine starts marking.
The laser radiation is dangerous to the eyes and skin.
Avoid eye or skin exposure to the laser radiation.
DANGER
Do not point the laser outlet at people to avoid
accidental laser injury.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 33 of 78
6 SOFEWARE SYSTEM
Filling Mirror
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 34 of 78
Zoom Out Zoom In
Delete Copy
Return Home
Save as File
Screen
Angle of Rotation
Distance Moved Once
Once
Battery Power
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 35 of 78
6.2 Add a New Text
Add New File →Text , press the screen within specific area, and then, select at
the bottom of screen to edit the text, as shown below:
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 36 of 78
6.3 Editing a Message
Select to enter the interface shown as below, edit the text and select the features for
the text:
1. Fill, space, angle
2. Text editing
3. Arc features
4. Text position, text length, width and height
5. Double line font
6. Single line font
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 37 of 78
6.4 Add a New Fixed Message
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 38 of 78
6.5 Add a 2D Code and Barcode
Click or on the home screen to create 2D code or barcode, select the generated 2D
6.5.1 2D Code
1. Filling
Fill Tpye: None, Line, Uline
Space: Space between filling lines
Angle: Angle of filling lines
Cross: Two fills with different angles
Enable Border: Overall frame
2. Rect
The Coordinate position and dimension of the 2D code
3. Text
Text: Fixed text, directly input the content of the 2D code
Variable: The content is variable (serial number, date and time are variables),
See section 6.6 for details.
4. 2D Code
Reverse: The inverse of the 2D code
Ratio: The spot size of the 2D code
X Axis & Y Axis: the multiple of the spots on X & Y axis
Delect: generate a blank area in the center of the 2D code. When it is 0, it will
not be generated by default. The larger the value, the larger the area.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 39 of 78
Type: 2D code type, supports QRCode,DataMatrix,GS1-DataMatrix,
AztecCode,HanXinCode,DotCode
Mode: Fill mode, including outline, rectangle, ellipse, point and line
6.5.2 Barcode
1. Filling
Fill Tpye: None, Line, Uline
Space: Space between lines
Angle: Angle of filling lines
Cross: Two fills with different angles
Enable Border: Overall frame
2. Rect
The Coordinate position and dimension of the barcode
3. Text
Text: Fixed text, directly input the content of the barcode
Variable: The text of barcode to be marked is variable (serial number, date and
time are variables), See section 6.6 for details.
4. Barcode
Barcode Type: 128CodeAuto/A/B/C,39code,93code,EAN13code,
PDF417code,01code
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 40 of 78
6.6 Add a New Variable
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 41 of 78
Loop: After all serial numbers are marked, start marking again from the first serial
number. If not checked, the marking data will be cleared and a pop-up window
indicating "Data is empty". The system will be returned to home screen when click
"OK".
For example, if the serial number to be set is 1 to 100, set the Begin Num with 1 and the
End Num is 100. The default increment is 1, the current value will +1 after marked. If set
the increment with 2, the current value will +2 after marked
If the Leading Zero is checked, the digit of the serial number will be the same with the
End Num and fill with 0 in front of the serial number. For example, if the End Num is 100,
checked the Leading Zero, the serial number will be 001, 002...099, 100.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 42 of 78
6.6.2 Set Date & Time
Template: The system provides template and custom template for user to choose
from. User can set the formats of month, week, date and time.
Deviation: Increment or decrement date or time of actual date or time.
Leading Zero: Display zeros in front of date or time. For example, the default date
and time is 2021-7-1 10:5:4. if it is checked, if the Leading Zero is checked, the value
will become 2021-07-01 10:05:04.
Template
Custom template
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 43 of 78
Template
Custom Template
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 44 of 78
6.6.4 Set TCP and UDP
Client Mode: Actively connect to receive text data from the server. The IP needs to be
set to the server IP, and the port must be the same as that of the server. The server must
open first before the client can connect.
Server Mode: Passive connection, receiving text data sent by the client. The IP defaults
to the local IP, and the port must be the same as that of the client. The server must be
opened first before the client can connect.
UDP: Bidirectional connection, either side can be opened first.
IP: IP address, the default is the same as the IP set in the network mode.
Port: Default is “8080”.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 45 of 78
6.6.5 Import Data through Files
File Type: Only supports TXT and Excel files (There can only be one data per line in the
TXT and Excel files).
Current: The current data ready to be mark.
Increment: Increment value.
Path: File location
IsLoop: Mark the data in the file cyclically.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 46 of 78
6.6.7 Add Data through Barcode Scanner
Users can use the barcode scanner to quickly import the required information such as
barcode, QR code and text.
1. Connect the Barcode scanner to the LD Series Handheld Laser Marking System
through the USB port.
2. Click 2D code (Barcode or Text ) icon on the Home screen. Refer to section 6.2 to
section 6.5 for detail operation.
3. Select the object and click Editor, click Variable setting.
4. Click Input, use the barcode scanner to scan the 2D code (or Barcode). The
information will be displayed on the screen, click OK, then click Close.
5. User can also click text to display the contents of the 2Dcode (or Barcode) on the
Home screen.
6. Click "Marking", then click "Start Mark", press the button on the handler, the system
will mark the information of input.
7. If the information needs to be changed, just scan another 2D code or barcode, then
do Step 6 again.
The laser radiation is dangerous to the eyes and skin.
Avoid eye or skin exposure to the laser radiation.
DANGER
Do not point the laser outlet at people to avoid
accidental laser injury.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 47 of 78
Description: Import Data through Barcode Scanner
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 48 of 78
6.7 Filling
Angle: 0 Angle: 30
Description: Filling Angle
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 49 of 78
Boarder No Boarder
Description: Border (Outline)
Line Uline
Description: Fill Type
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 50 of 78
6.8 Text Rounding
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 51 of 78
6.9 Add an Image
Click on the Home screen and import the image. LD Series Handheld Laser Marking
System only supports following picture formats:PLT, PNG, JPG, JPEG, BMP, GIF, PBM.
Note: PLT format is recommended.
Fill: When in image state, this parameter is not used. If the image format is PLT, needs to
fill the image object.
Rectangle: X&Y is the position of the image. Height& width is the size of the image
Threshold: Default auto setting. The threshold is used to determine which colors in the
picture are black or white.
Binarization: 0 and 255, the gray and white value of the picture, generally the default is 0,
and the reverse is 255. Set the binaryzation of the image can invert the color of the picture.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 52 of 78
6.10 Save File
Select to save the current message, enter file name and then click "Save File", shown as
follows:
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 53 of 78
6.11 Properties and Parameters
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 54 of 78
The initial value is set to 30kHz@20W, 37kHz@30W
The larger the value, the more the number of light spots arranged in the unit length,
the tighter. Appropriate spot spacing is conducive to the adjustment of the effect
Jump-Delay too long: has no negative effect on the visible scanning result. The
marking time will be longer.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 55 of 78
Delay in turning on the laser to wait for the galvanometer to complete the command
Laser-On-Delay too short: Burn-in effects at the starting point
Laser-On Delay too long: the vector is not marked from the starting point.
6.12 Marking
Select on the Home screen. Then click "Start Mark", press the button on the
handler, the laser unit starts marking.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 56 of 78
6.14 Settings
6.14.1 Mark
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 57 of 78
6.14.2 Laser
Password: laser
The default option is “Fiber”, do not select other options, otherwise laser machine
cannot work.
NO Signal Turn On Time: Laser gate signal, default 8000
NO Signal Turn Off Time: Laser gate signal, default 8000
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 58 of 78
6.14.3 Lens Correction
Password: lens
The lens parameter setting has been done before shipment, user doesn’t need to
correct it after receiving the machine.
Select the Settings on the home screen, enter to Settings. Select "Lens",
enter 100 in the blank of " Working Scope" if the machine’s working area is 100, then
click "Enable".
Note: if the mark field of the machine is 50mmx50mm , enter 50.
4. Use a straightedge to measure 4 sides, check whether the sides are aligned with
the straightedge, and whether the 4 corners are 90°right angles. If there is
deformation, you need to enter the corresponding parameters.
5. Measure the length of the XY axis, click "X Calculate" and "Y Calculate" to input
preset size and actual size. The actual size is the measure size, the preset size is
always the same as work scope(100)
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 59 of 78
6. Click "Correction" button and type "laser" in the pop-up window to save the
correction.
Target Effect
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 60 of 78
Decrease the SLant correction value
of the X axis, which can be a
X-axis Slant
negative value
deformation
increase the SLant correction value
correction
of the X axis, which can be a
negative value
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 61 of 78
6.14.3.2 Correct Method #2: 9 Points Correction
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 62 of 78
3) After clicking Settings, enter the setting screen. Click "Lens", enter the
calibration settings. Password is "lens".
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 63 of 78
4) Press "Laser Test", then press the button on the laser head, it will mark a
graphic like 田
5) Get a ruler to measure the XY length of the graphic 田, then enter the
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 64 of 78
6) Press "Correction", enter password "laser" to save the values.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 65 of 78
Point 1 XY Length
Point 2 Y Length
Point 3 XY Length
Point 4 XY Length
Point 6 X Length
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 66 of 78
Point 7 XY Length
Point 8 Y Length
Point 9 XY Length
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 67 of 78
6.14.4 I/O
Enable Beep: Set the beep sound (default) when marking and beep time.
The system provides four trigger mode:
Rising Edge: Buzzer sound before manual trigger
Falling Edge: Buzzer sound after manual trigger
Press and hold: User needs to press and hold the button on the handler till the
marking is completed
Normally open: This function is used for laser cleaning mode. After click "Start Mark"
on the screen, Single-click the button of the handler, the laser will start, and it will not
stop untill the second click is done.
Preview Speed: The red light preview speed, initial value is 200mm/s.
Red Type: Red light preview mode.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 68 of 78
6.14.5 System
1. Language :
Change the language of the software, Chinese and English by default.
2. Language package
Click to import the language package. The format of the language package is
“.qm”. For example, insert the USB disk to the USB port of the machine, click the
"Language" button, click "Go Back" and "Open file folder" to find the language,
select the language package that to be imported, click "Import" to import the
language package. Click "Exit" to save the changes and exit.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 69 of 78
Open file folder: Open the selected folder
Import: Copy and import language packages from an external storage card to the
device
Remove: Remove the selected language package
Go Back: Go back to the previous level of the folder
Exit: Click to save all changes in the system and exit.
3. Datetime
The current date and time of the system. User can change the datetime. Click
"Modify" and click "Exit" to save the changes and let it take effect.
4. NetWork Mode
View and modify IP address for LAN and WIFI connection.
5. Touch Screen
Calibrate the touch accuracy of the screen.
6. Import Font
Import different fonts from the USB device. The format of the font files is .ttf or .shx.
Click "Import Font" to find the folder where the fonts are stored in the "Devices",
select the font that to be imported, and click "Import". Click "Exit" to save the
changes and exit.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 70 of 78
Description: Import Fonts
7. Update Information
Copy and import the company information file from the USB devices. The file
name and format is "COMPANY.INI". The information is as below:
8. Update Logo
Startup screen, copy and import image files (PNG, JPG, JPEG, BMP) from USB
devices. Click Update Logo button and enter password "logo" to modify the
system startup screen logo. Select the logo then click "Import logo" button.
9. Test Mode
Click the Test Mode button and enter different password to test different function.
1) Password "power": show battery icon on the upper right corner of the screen.
The battery version is checked by default.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 71 of 78
3) Password "laser": Continuous laser output laser for testing laser power, used
to test the laser power.
Remove the lens, open the red light to aim at the center surface of the power
meter, wear the protective glasses, click "start" then click "OK" in the pop-up
window to start the laser. Do not move the scan head and make sure that
eyes or skin not to exposure to the laser radiation.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 72 of 78
6.15 WIFI Connection
1. Plug the WIFI adapter into the USB port, then click "Settings", then click "System", select
"Network Mode". Click WIFI, select the WIFI gateway and enter the password, click "OK".
Wait a moment, the connection will be completed in a few seconds, and the IP address
will be obtained and displayed automatically, for example, IP 192.168.19.102 . Go back to
Home screen.
2. Create a new text. Select "Variable Text", select "Udp", enter the IP address
192.168.19.102 in the box the same as which set in the WIFI IP address , click "Confirm".
(Udp://192.168.19.102. Port: 8080 This IP address will be used when using software for
data transmission on PC).
4. Connect the PC to the same network, make sure that the IP address of the PC is in the
same network segment as the LD Handheld Fiber Laser Marking System. Start the
software "Netassist" on PC. (Contact SUNINE for the software).
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 73 of 78
5. Select (1) Udp, (2) enter the IP address of PC. For example, if the PC IP is
192.168.19.210 , then enter 192.168.19.210, (3) Enter 8080. Click "Open". Enter the IP
address of the laser marking machine:192.168.19.102, port: 8080.
7. Then switch to ASCII, “0203” will be transfer into 2 blank space, input the desired
message in the MIDDLE of 2 blank space, then click "Send". An "OK" will come out if the
message info was sent successfully.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 74 of 78
The desired message must be in put in the
IMPORTANT MIDDLE of the two blank space, otherwise
the message will not be sent successfully.
8. After sending successfully, the handheld laser machine will receive the message info from
the software, click “Start Mark” button to mark the message.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 75 of 78
7 MAINTENANCE
In prior to any operation, the user should read this instructions carefully. The laser system is
designed such that maintenance can be performed safely.
In order to achieve the best printing results and prevent damage, the maintenance of the laser
system is very important. It is necessary to establish a maintenance schedule for the laser
marking system considering the working intensity of the equipment and the characteristics of the
printed products.
3. Clean up the dust accumulated on the air vents on the surface of the machine
housing weekly.
4. If the system is not turned on for a long time, it must be powered off, and cover
the laser head and control unit with a cover cloth to avoid dust accumulation and
moisture-proof.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 76 of 78
7.2.2 Clean the Lens
Note that any dirt, dust and other contaminants on the surface of the beam exit can
absorb laser energy and burn into the surface to damage the optical elements. The
warranty does not cover any damage due to improper use, cleaning or handling.
1. Before cleaning, ensure that the laser system is shut down and can not be
accidentally turned on again.
2. Use clean gloves or finger cots. Avoid touching the mirror with skin as
fingerprints contain aggressive substances that can damage the optical
surfaces.
3. If dust particles are inspected, remove them by blowing air on the mirror surface
with a rubber squeeze bulb.
4. If the lens surface is still not clean, use a cotton ball or swab with high-purity
isopropanol or acetone to uniformly clean the surface. Don’t use too much
solvent, otherwise drying marks might appear.
5. If the dust cannot be removed by air, or if inspect more serious contamination,
contact SUNINE LASER for guidance. In extreme cases, the lens must be
returned to SUNINE LASER for inspection and cleaning.
SUNINE recommend to clean the lens by blowing air not less than once per day. The
cleaning frequency depends on the specific environmental conditions of the production
site. If there is a lot of smoke and particles on the production site, the lens will get dirty
faster, which requires more frequent cleaning. Each user should establish
corresponding cleaning requirements according to the production situation.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 77 of 78
8 TROUBLESHOOTING
If problems occur while operating the laser, verify that all operating instructions have been adhered to
and then carry out the following troubleshooting procedures:
The galvanometer does Check whether the motor on the galvanometer vibrates.
3
not swing Check whether the two motors on the galvanometer are tight.
© 2022 GUANGZHOU SUNINE INTELLIGENT TECHNOLOGY CO., LTD. Manual LD Series Handheld Fiber Laser Marking System Page 78 of 78