Professional Documents
Culture Documents
AlertsEvents BC 150415
AlertsEvents BC 150415
Alerts
Alert 1 Service has been disabled Service of this module has been disabled and will no longer function in the
system.
Alert 2 Service has been enabled Service of this module has been re-enabled for use in the system.
Alert 3 No flame detected at flame amplifier %d No flame was detected at this flame amplifier.
Alert 4 Weak flame detected at flame amplifier %d A weak flame was detected at this flame amplifier.
Alert 5 Flame detected at flame amplifier %d Flame was detected at this flame amplifier.
Alert 6 Unexpected flame amplifier found at %d An unexpected flame amplifier was found attached to this burner control
module.
Alert 7 Non-flame amplifier device connected at %d A device that is NOT a flame amplifier was detected in connection to this
burner control module.
Alert 8 Flame amplifier type mismatch at %d A flame amplifier of the wrong type has been detected for this burner
control module.
Alert 9 Auto flame in Run established Auto flame has been established
Alert 10 Auto flame in Run lost Auto flame has been lost
Events
Information 1 No event No event is currently being reported.
Lockout 2 NV storage not initialized Non-volatile storage is not initialized.
Lockout 3 Configuration parameters mismatch Configuration parameters do not match with Base module.
Information 4 Configuration file received Configuration parameter setting file has been received by this module.
Information 5 Service disabled This module's service has been disabled.
Information 6 Service enabled This module's service has been enabled.
Information 7 Safety verification file received Safety verification file received by this module.
Information 8 Module powered up %s This module has just powered up and is initializing.
Information 9 Autogen reserved 9 Reserved for future use
Information 10 Autogen reserved 10 Reserved for future use
Fault 11 Setting error for parameter %d "%s" Invalid configuration parameter setting for this register has been detected.
Fault 12 Safety verification needed Verification of one or more safety parameter changes is needed.
Fault 13 Safety relay not in correct state Safety relay output was ON when it should be off or OFF when it should be
on.
Fault 14 Safety relay optocoupler error Safety relay optocoupler feedback was not valid.
Fault 15 Safety relay test failure Safety relay failed during self-test.
Fault 16 Interlock is OFF when it should be ON Interlock (ILK) string is OFF when it should be ON.
Fault 17 Preignition is OFF when it should be ON Preignition (PII) string is OFF when it should be ON.
Fault 18 Main valve is NOT in correct state Main valve (MV1) is ON when it should be off or is OFF when it should be
on.
Fault 19 Second Main valve is NOT in correct state Second Main valve (MV2) is ON when it should be off or is OFF when it
should be on.
Fault 20 Pilot valve is NOT in correct state Pilot valve is OFF when it should be on or ON when it should be off.
Fault 21 Purge position is NOT proven by PPP Purge position is NOT proven according to the PPP terminal.
Fault 22 Purge position is NOT proven by fan Purge position is NOT proven by fan speed.
Fault 23 Lightoff position is NOT proven by LPP Lightoff position is NOT proven according to the LPP terminal.
Fault 24 Lightoff position NOT proven by Fuel Air control Lightoff position is NOT proven according to the Fuel Air control module.
Fault 25 Flame is ON when it should be off Flame is present when no flame should be.
Fault 26 IAS/LOI input is OFF when it should be ON IAS/LOI input is OFF when it should be ON
Fault 27 IAS input is ON during start check IAS input is ON during start check
Fault 28 Flame ON when no flame should be present Persistent flame is present during period when there should be no flame.
Fault 29 Manual Open Switch is OFF Manual open switch (MOS) is OFF when it should be ON.
Information 30 Forced recycle Forced recycle time was exceeded in run
Fault 31 Flame is OFF Flame is not present when it should be.
Fault 32 Safety relay feedback is OFF Safety relay feedback is off when it should be on.
Lockout 33 Reset button pressed Reset button was pressed.
Fault 34 Fuel Air lockout requested Fuel Air control module has requested a lockout. (%d)
Fault 35 Fuel Air hold requested Fuel air control module requested a hold.
Fault 36 LCI/F1 and LCI/F2 were both ON Both Fuel 1 and Fuel 2 inputs were ON simultaneously.
Fault 37 Fuel Air communications timeout Communication with Fuel Air control module has timed out.
Fault 38 LCI/F1 was OFF LCI/F1 input was OFF.
Fault 39 Purge time expired Purge time has expired.