Sharp LC 22le240

You might also like

Download as pdf or txt
Download as pdf or txt
You are on page 1of 88

LC-22LE240

1st Edition
50mm

SERVICE MANUAL
40mm
Issued: 26 March 2012

LED LCD COLOUR TELEVISION


31.5mm
DVB-T / DVB-C (HDTV), PAL B/G, I / SECAM B/G, D/K, L/L’ SYSTEM COLOUR TELEVISION
17MB62 CHASSIS
25mm

20mm
MODEL
LC-22LE240E
LC-22LE240EV
LC-22LE240RU
In the interests of user safety (required by safety
regulations in some countries) the set should be re-
stored to its original condition and only parts identical
to those specified should be used.

CONTENTS
TABLE OF CONTENTS ....................................................................................................................... 2
ELECTRICAL SPECIFICATIONS ....................................................................................................... 5
IMPORTANT SERVICE SAFETY PRECAUTIONS ................................................................................ 6
OPERATION MANUAL ........................................................................................................................... 9
DIMENSIONS ..................................................................................................................................... 15
INTRODUCTION .................................................................................................................................. 16
CIRCUIT DESCRIPTIONS .................................................................................................................. 19
SERVICE MENU SETTINGS ........................................................................................................... 51
SOFTWARE UPDATE ............................................................................................................................ 56
TROUBLESHOOTING ..................................................................................................................... 57
OVERAL WIRING DIAGRAM ........................................................................................................... 65
SCHEMATIC DIAGRAMS ................................................................................................................ 66
PRINTED WIRING BOARD ....................................................................................................................... 76
REPLACEMENT PARTS LISTING ............................................................................................... 77
CABINET AND MECHANICAL PARTS LISTING ...................................................................... 86

SHARP CORPORATION This document has been published to


be used for after sales service only.
The contents are subject to change without notice.
1
LC-22LE240

TABLE OF CONTENTS

i SPECIFICATIONS .......................................................................................................................... 5
ii IMPORTANT SERVICE SAFETY PRECAUTIONS ......................................................................... 6
iii OPERATION MANUAL ................................................................................................................. 9
iv DIMENSIONS ............................................................................................................................... 15
0. INTRODUCTION ........................................................................................................................... 16
0.1. General Block Diagram ................................................................................................. 17
0.2. MB60 Placement of Blocks ........................................................................................... 18

1. TUNER(TU3) ................................................................................................................................. 19
1.1. General description of Sony RE216 ........................: .................................................... 19

2. AUDIO AMPLIFIER STAGE WITH AZAD2102(U163, U164) ........................................................ 21


2.1. General Description ...................................................................................................... 21
2.2. Features ........................................................................................................................ 21
2.3. Absolute Ratings ........................................................................................................... 22
2.3.1. Electrical Characteristics ........................................................................................ 22
2.3.2. Operating Specifications. ....................................................................................... 23
2.4. Pinning ............................................................................................................,............. 23

3. AUDIO AMPLIFIER STAGE WITH TPA3113 (U168,) .................................................................. 24


3.1. General Description .................................................................................................... 24
3.2. Features ........................................................................................................................ 24
3.3. Absolute Ratings .......................................................................................................... 24
3.3.1. Electrical Characteristics ........................................................................................ 24
3.3.2. Operating Specifications ........................................................................................ 25
3.4. Pinning .......................................................................................................................... 25

4. POWER STAGE ............................................................................................................................ 26


4.1. Power Management ...................................................................................................... 29

5. MICROCONTROLLER – MSTAR ( U5 ) ....................................................................................... 31


5.1. General Description ...................................................................................................... 31
5.2. MSTAR Block Diagram ................................................................................................. 35
5.3. Reset Circuit .................................................................................................................. 35

6. CI INTERFACE .............................................................................................................................. 36

7. USB INTERFACE .......................................................................................................................... 36

8. DDR2 SDRAM K4T1G146QF ( U155 ) ......................................................................................... 37


8.1. General Description ..................................................................................................... 37
8.2. Features ....................................................................................................................... 37
8.3. Pinning ......................................................................................................................... 38

9. SCALER AND LVDS SOCKETS.. ................................................................................................. 39


9.1. LVDS sockets Block Diagram ..................................................................................... 39
9.2. Panel Supply Switch Circuit ......................................................................................... 39

10. SPI FLASH MEMORY - MX25L1005 (U158) ............................................................................. 40


10.1. General Description .................................................................................................... 40

2
LC-22LE240

10.2. Features ...................................................................................................................... 41


10.3. Absolute Maximum Ratings ........................................................................................ 41
10.4. Pinning ........................................................................................................................ 41

11. NAND FLASH MEMORY – NAND512XXA2C (U162) ................................................................ 42


11.1. General Description .................................................................................................... 42
11.2. Features ...................................................................................................................... 42
11.3. Pinning ........................................................................................................................ 43

12. LM1117(U175, U180, U181) ....................................................................................................... 44


12.1. General Description .................................................................................................... 44
12.2. Features ...................................................................................................................... 44
12.3. Applications ................................................................................................................. 44
12.4. Absolute Maximum Ratings ........................................................................................ 44
12.5. Pinning ........................................................................................................................ 44

13. MP2012 (U176) ........................................................................................................................... 45


13.1. General Description .................................................................................................... 45
13.2. Features ...................................................................................................................... 45
13.3. Pinning......................................................................................................................... 45

14. RTA8283A (U23, U173) .............................................................................................................. 46


14.1. General Description .................................................................................................... 46
14.2. Features ...................................................................................................................... 46
14.3. Pinning......................................................................................................................... 46

15. MP1583 (U174) ........................................................................................................................... 47


15.1. General Description .................................................................................................... 47
15.2. Features ...................................................................................................................... 47
15.3. Pinning ........................................................................................................................ 47

16. FDC642 ....................................................................................................................................... 48


16.1. General Description .................................................................................................... 48
16.2. Features ...................................................................................................................... 48
16.3. Pinning ........................................................................................................................ 48

17. FDC604P...................................................................................................................................... 49
17.1. General Description .................................................................................................... 49
17.2. Features ...................................................................................................................... 49
17.3. Pinning ........................................................................................................................ 49

18. CONNECTORS ........................................................................................................................... 49


18.1. SCART (SC1) ............................................................................................................. 49
18.2. HDMI (CN707,CN708) ................................................................................................ 50
18.3. VGA (CN132) .............................................................................................................. 50

19. SERVICE MENU SETTINGS ...................................................................................................... 51


19.1. Video Settings ............................................................................................................. 52
19.2. Audio Settings ............................................................................................................. 52
19.3. Options ........................................................................................................................ 53
19.4. Tuning Settings ........................................................................................................... 54
19.5. Source Settings ........................................................................................................... 54

3
LC-22LE240

19.6. USB Operations .......................................................................................................... 55


20. SOFTWARE UPDATE ................................................................................................................. 56

21. TROUBLESHOOTING ................................................................................................................ 57


21.1. No Backlight Problem ................................................................................................. 57
21.2. CI Module Problem .................................................................................................... 58
21.3. Led Blinking Problem .................................................................................................. 60
21.4. IR Problem .................................................................................................................. 61
21.5. Keypad Touchpad Problems ....................................................................................... 62
21.6. USB Problems ............................................................................................................. 62
21.7. No Sound Problem ...................................................................................................... 63
21.8. No Sound Problem at Headphone............................................................................... 63
21.9. Standby On/Off Problem.............................................................................................. 64
21.10. No Signal Problem .................................................................................................... 64

22. OVERALL WIRING DIAGRAM .................................................................................................... 65

23. SCHEMATIC DIAGRAMS ........................................................................................................... 66

24. PRINTED WIRING BOARD ......................................................................................................... 76

25. REPLACEMENT PARTS LISTING .............................................................................................. 77

26. CABINET AND MECHANICAL PARTS LISTING ........................................................................ 86

4
LC-32LE210 LC-22LE240
LC-32LE220

ELECTRICAL
ELECTRICALSPECIFICATIONS
SPECIFICATIONS
Specifications
LC-22LE240E/EV/RU Specifications
Item 24” LCD
LCD COLOUR
COLOUR TV,TV, Model:
Model: 32” LCD COLOUR TV, Model:
LC-24LE210E, LC-32LE210E, LC-32LE220E,
Specications Digital Reception
LC-32LE210E,
LC-24LE220E
(DVB-C)
LC-32LB220E, LC-32LE220E, LC-32LS220E.
LC-32LB220E, LC-32LS220E
TV BROADCASTING Transmission Standards:
LCD Panel 32” TFT
24" LCD TFT
BLACK LED LCD
TV LED TV 32” BLACK TFT LCD LED TV
PAL/SECAM B/G D/K K’ I/I’ L/L’ DVB-C, MPEG2, DVB-C, MPEG4
Resolution 6.220.800 dots (1.920 x 1.080 pixels)
RECEIVING CHANNELS i. DEMODULATION
Video Colour System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
VHF (BAND I/III) -Symbolrate: 4.0 Msymbols/s to 7.2 Msymbols/s
TV Standard Analogue CCIR (B/G, I, D/K, L/L’)
UHF (BAND U) - Modulation: 16-QAM , 32-QAM ,64-QAM, 128-QAM
Digital DVB-T (2K/8K OFDM)(H.264), DVB-C (Only Lx220)
and 256-QAM
HYPERBAND
TV
VHF/UHF E2–E69 ch, F2–F10 ch, I21–I69 ch, IR A–IR J ch (Digital: IR A ch–E69 ch)
Func- ii. VIDEO
NUMBER OF PRESETReceiving
CHANNELS Channel CATV Hyper-band, S1–S41 ch
tions - All MPEG2 MP@ML formats with up-conversion and
1000
TV-Tuning System ltering
Auto to CCIR601
Preset 999 format.
ch: non-Nordic / 9999 ch: Nordic (ATV: 99 ch), Auto Label, Auto Sort
CHANNEL INDICATOR
STEREO / BILINGUAL -CVBS
NICAM/A2 analogue output
On Screen Display
Viewing angles iii. AUDIO
H: 176°, V: 176°
RF AERIAL INPUT
Audio Amplifier -All
10 W x 2MPEG1 Layer 1 and 2 modes
75 Ohm (unbalanced) (30-Sampling
Speaker (25 mm
mmxx100 frequencies
100mm)
mm)xx
22 supported are
(30 32,
mm x44.1 & 48x 2
100 mm)
OPERATING VOLTAGE kHz 75
TV Antenna UHF/VHF Din type (Analogue & Digital)
220-240V AC, 50Hz.
SERVICE Ø 3.5 mm jack
AUDIO
SCART SCART (AV input, RGB input, TV output, Y/C input)
German + Nicam Stereo
PC INPUT VGA (D-Sub 15pin), Ø 3.5mm jack
AUDIO OUTPUT POWER (WRMS.) (10% THD)
COMPONENTS COMPONENT IN: Y/PB(CB)/PR(CR), RCA (AUDIO R/L)
2 x 2,5
HDMI1 HDMI, Ø 3.5mm jack
POWER CONSUMPTION (W)
HDMI2 HDMI, Ø 3.5mm jack
45 W (max) Terminals
HDMI3 HDMI, Ø 3.5mm jack
< 0,5 W (Standby)
AV RCA connector (AV input)
PANEL
MEDIA PLAYER/ TIME-SHIFT/ USB 2.0 HOST (A type)
16:9 display, 22” (55 cm) Screen Size
USB REC
DIMENSIONS (mm)
DIGITAL AUDIO OUTPUT RCA S/PDIF digital audio output.
DxLxH (With foot): 149 x 534,6 x 377,4
C. I. (Common Interface) EN50221, R206001, CI+ speci cation (Only Lx220)
Weight (Kg): 4,3
Headphones Ø 3.5 mm jack (Audio output)
DxLxH (Without foot): 35 x 534,6 x 352,4
Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian,
Weight (Kg):OSD
3,7 language Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slovene, Spanish,
Swedish, Turkish, Ukrainian, Byelorussian, Romanian.

Power Requirement AC 220–240 V, 50 Hz


Power Consumption (IEC62087 Method) 85 W (0.25
30W (0.25 W
W(Standby)
Standby) 85W (0.25 W Standby)
Weight 8,5 Kg
4,9 Kg(Without
(Withoutstand), 9,86 Kg
stand), Kg(With
(Withstand)
stand) 8,5 Kg (Without stand), 9,8 Kg (With stand)
Operating Temperature 0 °C to +40 °C

MHEG-5 ENGINE compliant with ISO/IEC 13522-5 UK engine Prole 1


Environmental Specifications
Object carousel support compliant with ISO/IEC 135818-6 and UK DTT prole for UK
Frequency range: 474-850 MHz for UK models according to IEC 62087 Ed. 2.
*1 Measured
32”
170-862 MHz for EU models*2 For further information about the Energy Save function,
Digital *1 On-Mode (W) (HOME MODE) 63 W please see related pages in this operation manual.
Reception*2 Energy-Save-Mode Transmission
(W)
standard:
ECO
DVB-T.
48 W
MPEG-2, MPEG-4according to IEC 62301 Ed. 1.
*3 Measured
*3 Standby-Mode (W) Demodulation: COFDM with 2K/8K
0.25 W FFT
*4 mode according to IEC 62301 Ed. 1.
Measured
*5 Annual energy consumption is calculated on the basis
*4 Off Mode (W) FEC: all DVB modes
0.18 W
of the On-Mode (HOME MODE) power consumption,
*5 Annual Energy Consumption (kWh)
Video: MP@ML, 92 kWh4:3/16:9 watching TV 4 hours a day, 365 days a year.
PAL,
*6 Annual Energy Consumption ECO 71 kWh *6 Annual energy consumption is calculated on the basis of
Energy-Save-Mode (kWh) Audio: MPEG Layer I&II 32/44.148kHz.
the Energy-Save-Mode power consumption, watching TV
4 hours a day, 365 days a year.

English - 38 -
Cautions regarding use in high and low temperature environments • As a part of our policy of continuous im-
provement, SHARP reserves the right to
• When the unit is used in a low temperature space (e.g. room, office), the
A01_MB62_[GB]_1910UK_IDTV_TC_PVR_BRONZE19_22942LED_ROCKER_10075676_5020xxxx.indd 38
make design and specification changes
25.11.2011 14:50:23
picture may leave trails or appear slightly delayed. This is not a malfunc-
for product improvement without prior
tion, and the unit will recover when the temperature returns to normal.
notice. The performance specification fig-
• Do not leave the unit in a hot or cold location. Also, do not leave the
ures indicated are nominal values of pro-
unit in a location exposed to direct sunlight or near a heater, as this may
duction units. There may be some devia-
cause the cabinet to deform and the LCD panel to malfunction. Storage
tions from these values in individual units.
temperature: –20°C to +60°C.

2
5
LC-22LE240

IMPORTANT SERVICE SAFETY PRECAUTION


Service work should be performed only by qualified service technicians who are thoroughly familiar with all
safety checks and the servicing guidelines which follow:

WARNING
1. For continued safety, no modification of any circuit should be attempted.
2. Disconnect AC power before servicing.

CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF


FIRE REPLACE ONLY WITH SAME TYPE
F700, F701 (T 3.15A L250V)

BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard)


Before returning the receiver to the user, perform the following safety checks:
1. Inspect all lead dress to make certain that leads are not pinched, and check that hardware is not lodged between the
chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic control knobs, insulation materials, cabinet backs, adjustment and
compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc.
3. To be sure that no shock hazard exists, check for leakage current in the following manner.
LC-20B5E
• Plug the AC cord directly into a 220~240 volt AC outlet. (Do not use an isolation transformer for this test).
•Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal
cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.
•A true RMS reading multimeter should be used for this test, especially where the equipment uses a switch mode
power supply which may result in very non-sinusoidal leakage current.
•Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet,
screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.

All checks must be repeated with the AC cord plug connection reversed. (If necessary, a nonpolarized adaptor plug must
be used only for the purpose of completing these checks.)
Any reading of 1.05V peak (this corresponds to 0.7 mA. peak AC.) or more is excessive and indicates a potential shock
hazard which must be corrected before returning the monitor to the owner.

DVM
AC SCALE
1.5k ohm
10W

0.15 µF
TEST PROBE

TO EXPOSED
CONNECT TO
METAL PARTS
KNOWN EARTH
GROUND

SAFETY NOTICE
Many electrical and mechanical parts in LCD television have special safety-related characteristics.
These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily
increased by using replacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics are identified in this manual; electrical components
having such features are identified by “ ! “.

For continued protection, replacement parts must be identical to those used in the original circuit.
The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended
replacement parts shown in this service manual, may create shock, fire or other hazards.

6
LC-22LE240

PRECAUTIONS FOR USING LEAD-FREE SOLDER

1 Using lead-free wire solder


When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead
wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend you to
use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our
service station or service branch in your area.

2 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead solder by
40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended
period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be
exceeded, remove the bit from the PWB as soon as you confirm the steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and
off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every
use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.

Be careful when replacing parts with polarity indication on the PWB silk.

Lead-free wire solder for servicing.

7
LC-22LE240

END OF LIFE DISPOSAL


End of life disposal
A. Information on Disposal for Users (private households)

1. In the European Union


Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!

Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires
proper treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used
electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local
Attention: Your product retailer may also take back your old product free of charge if you purchase a similar new one.
is marked with this
*) Please contact your local authority for further details.
symbol. It means that
used electrical and
electronic products If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately
should not be mixed beforehand according to local requirements.
with general household
waste. There is a By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery
separate collection and recycling and thus prevent potential negative effects on the environment and human health which could otherwise
system for these
arise due to inappropriate waste handling.
products.

2. In other Countries outside the EU


If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.

For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.

B. Information on Disposal for Business Users


1. In the European Union
If the product is used for business purposes and you want to discard it:

Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for
the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local
collection facilities.

For Spain: Please contact the established collection system or your local authority for take-back of your used
products.

2. In other Countries outside the EU


If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.

The battery supplied with this product contains traces of Lead.

For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste!
There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with
legislation. Please contact your local authority for details on the collection and recycling schemes.

For Switzerland: The used battery is to be returned to the selling point.

For other non-EU countries: Please contact your local authority for correct method of disposal of the used battery.

8
LC-22LE240

OPERATION MANUAL

Remote Control Buttons


1. Standby
2. Image size / Zooms videos (in Media Browser
video mode)
3. Sleep Timer SLEEP SCREEN PRESETS

4. Mono / Stereo - Dual I-II / Currrent Language (*)


(in DVB channels) FAV LANG.

5. Favourite Mode Selection (in DVB channels)


6. Numeric buttons
7. Electronic programme guide (in DVB channels)
8. No function
9. Media Browser
10. Navigation buttons (Up/Down/Left/Right)
EPG SWAP

11. No function
12. Recordings Library SOURCE

13. Programme Down / Page up - Programme Up /


Page down
14. Mute
15. Programme recording
16. Pause (in Media Browser mode) / Timeshift
recording
17. Rapid reverse (in Media Browser mode) C
18. Play (in Media Browser mode) DISP. SEARCH
MODE

19. Red button


INFO
20. Green button / List Schedule (in EPG) / Tag
CH V
/ Untag All (in favourite list) / Play-Slideshow
(in Media Browser) / Loop-Shufe (in Media
Browser)
21. Picture mode selection / Changes picture mode
(in Media Browser video mode)
22. No function
23. Teletext / Mix (in TXT mode)
24. Subtitle on-off (in DVB channels)
25. Previous programme
26. AV / Source selection
27. Menu on-off
28. Okay (Conrm) / Hold (in TXT mode) / Edit
Channel List
29. Exit / Return / Index page (in TXT mode)
30. No function
31. Info / Reveal (in TXT mode) 36. Stop (in Media Browser mode)
32. Volume Up / Down 37. Blue button / Edit Channel List / Filter (In
Favourite List&EPG)
33. No function
38. Yellow button / Timeline Schedule (in EPG)
34. No function
35. Rapid advance (in Media Browser mode)

English - 8 -

A01_MB62_[GB]_1910UK_IDTV_TC_PVR_BRONZE19_22942LED_ROCKER_10075676_5020xxxx.indd 8 25.11.2011 14:50:00

9
LC-22LE240

Operation Manual (Continued)

LCD TV and Operating Buttons


FRONT and REAR VIEW Control buttons VIEW Control Buttons
1. Up direction
2. Down direction
3. Programme/Volume / AV /
Standby-On selection switch
Note:You can move the switch, upward
or downward to change the volume. If
you want to change channels, press the
middle of the switch once (Position 3)
and then move upward or downward. If
you press the middle of the switch once
more, source OSD will be displayed. To
select desired source, move the switch
upward or downward and release. If you
press the middle of the switch and hold
about a few seconds, the TV will switch to
standby mode. Main menu OSD cannot be
displayed via control buttons.

Viewing the Connections - Back Connectors


1

VGA
SPDIF

Coax.OUT

SCART

4. HDMI 1: HDMI Input


HDMI Inputs are for connecting a device that has an HDMI socket. Your LCD TV is capable of
displaying High Denition pictures from devices such as a High Denition Satellite Receiver or DVD
Player. These devices must be connected via the HDMI sockets or Component Socket. These sockets
can accept either 720p or 1080i signals. No sound connection is needed for an HDMI to HDMI
connection.
5. RF Input connects to an aerial antenna system or a cable.
Note that if you use a decoder or a media recorder, you should connect the aerial cable through the device
to the television with an appropriate antenna cable, as shown in the illustration in the following pages.
6. SCART input or output for external devices. Connect the SCART cable between SCART socket on TV and
SCART socket on your external device (such as a decoder, a VCR or a DVD player).
Note: If an external device is connected via the SCART socket, the TV will automatically switch to AV mode.
Note: S-VHS signal is supported via the scart socket (optional).
7. PC Input is for connecting a personal computer to the TV set.
Connect the PC cable between the PC INPUT on the TV and the PC output on your PC.
8. SPDIF Coaxial Out outputs digital audio signals of the currently watched source.
Use an SPDIF coaxial cable to trasfer audio signals to a device that has SPDIF input
English - 9 -

10
A01_MB62_[GB]_1910UK_IDTV_TC_PVR_BRONZE19_22942LED_ROCKER_10075676_5020xxxx.indd 9 25.11.2011 14:50:01
LC-22LE240

Operation Manual (Continued)

Viewing the Connections - Side Connectors


1. CI Slot is used for inserting a CI card. A CI card allows you to view all the channels that
you subscribe to. For more information, see “Conditional Access” section.
2. USB Inputs.
Note that programme recording feature is available via these USB inputs. You can connect
external hard disk drives to this input.
3. Component Video Input (YPbPr) is used for connecting component video.
You can connect the component video and audio sockets with a device that has
component output. To do this, you must use the supplied component video connection
cable for enabling connection. First, plug single jack of the cable to the TV’s YPbPr socket
(side). Afterwards, insert your component cable’s (not supplied) connectors into the plural
5Vdc
Max:500mA

part of the Component video connection cable. Colours of the connected jacks should
match.

YPbPr
4. Side audio-video connection input is used for connecting video and audio signals of
external devices. To make a video connection, you must use the supplied AV connection

SIDE AV
cable for enabling connection. First, plug singular jack of the cable to the TV’s Side AV
socket. Afterwards, insert your video cable’s (not supplied) connector into the YELLOW
input (located on the plural side) of the supplied AV connection cable. Colours of the

MODE
o
connected jacks should match.
To enable audio connection, you must use RED and WHITE inputs of the side AV
connection cable. Afterwards, insert your device’s audio cable’s connectors into the RED
and WHITE jack of the supplied side AV connection cable. Colours of the connected jacks should
match.
Note: You should use audio inputs of side AV connection cable (RED &
WHITE) to enable sound connection when connecting a device to your TV by
using PC or COMPONENT VIDEO input.
5. Headphone jack is used for connecting an external headphone to the
system. Connect to the HEADPHONE jack to listen to the TV from
headphones (optional).
6. Volume/ Programme/ Source and Standby-On switch
7. , switch is used for turning the TV on or off.

Power Connection
IMPORTANT: The TV set is designed to operate on 220-240V AC, 50Hz.
• After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the
mains. Plug the power cable to the mains socket outlet.
Aerial Connection
• Connect the aerial ,cable TV plug to the AERIAL INPUT socket located at the rear of the TV.

Aerial or Cable
1

VGA
SPDIF

Coax.OUT

SCART

11
English - 10 -
LC-22LE240

Operation Manual (Continued)

CAUTION !
Using USB Inputs
• Quickly plugging and unplugging USB devices,
USB Connection is a very hazardous operation. Especially, do not
• You can connect a USB hard disk drive or USB repeatedly quickly plug and unplug the drive. This
memory stick to your TV by using the USB inputs may cause physical damage to the USB player and
of the TV. This feature allows you to play les stored especially the USB device itself.
in a USB drive or record programmes. • Do not pull out USB module while playing or
• 2.5” and 3.5” inch (hdd with external power supply) recording a le.
external hard disk drives are supported. Programme Recording
• To record a programme, you should rst connect To record a programme, you should rst connect a
a USB disk to your TV while the TV is switched USB disk to your TV while the TV is switched off.
off. You should then switch on the TV to enable You should then switch on the TV to enable recording
recording feature. Otherwise, recording feature will feature.
not be available.
IMPORTANT: When using a new USB hard disk drive,
IMPORTANT ! it is recommended that you rst format the disk using
• You may back up your les before making any your TV’s “Format Disk” option.
connections to the TV set in order to avoid any • For using recording function, you should connect a
possible data loss. Note that manufacturer will not USB disk or an external hard disk drive to the TV
be responsible for any le damage or dataloss. and connected USB disk should have at least 1 GB
• It is possible that certain types of USB devices (e.g. capacity and should have 2.0 speed compatibility.
MP3 Players) or USB hard disk drives/memory sticks If the connected USB device does not support 2.0
may not be compatible with this TV. speed, an error message will be displayed.
IMPORTANT: The TV supports only FAT32 and Note: Recorded programmes are saved into the
NTFS disk formatting. However, NTFS format is not connected USB disk. If desired, you can store/copy
supported for recording features. For recording, if you recordings on a computer; however, these les will
connect a USB disk with NTFS format, the TV will ask not be available to be played on a computer. You can
you to format the content. See the section, “Format play the recordings only via your TV.
Disk” in the following pages for more information on • For more information on recording programmes,
disk formatting. see sections “Instant Recording”, “Timeshifting”,
Note that ALL the data stored on the USB disk will “Electronic Programme Guide”, “Recordings Library”
be lost and then the disk format will be converted to or “Recording Timers” in the following parts.
FAT32 in such a case. • Recorded programmes are split into 4GB
USB Disk Connection partitions.
• Plug your USB device to the USB input of the TV. • Recorded programmes are stored in the following
Note: Plug or unplug your USB disk while the TV is directory of the connected USB disk: \DVR\RECS.
switched off. All recordings are indicated with a number. A text
(txt) le is created for each recording. This text
Note: If you are going to connect a USB hard disk drive
file includes information such as broadcaster,
to the TV set, USB connection cable used between
programme, and recording time.
the disk drive and the TV should have a USB logo
and should be as short as possible. • Timeshifting may be stopped according to USB
device write speed. If the USB device speed is not
Note: While formatting a USB hard disk that has 1TB
enough for video stream bitrate, timeshifting may
(Tera Byte) or more le capacity, you can experience
be stopped and recording may fail. If HD service
problems with the formatting process. In such a
bitrate is greater than 13 Mbp/sec. some freeze can
case, you should format the disk with your personal
be seen during timeshifting on both USB disk and
computer and the formatted disk type should be
on external HDD.
FAT32.
• Recordings of HD programmes can occupy bigger
SIDE VIEW USB MEMORY size on the USB disk depending on the broadcast’s
resolution. For this reason it is recommended
USB to use USB hard disk drives for recording HD
programmes.

5Vdc
• Do not plug out the USB/HDD during the recording.
Max:500mA
This may harm the connected USB/HDD.

English - 11 -

12
A01_MB62_[GB]_1910UK_IDTV_TC_PVR_BRONZE19_22942LED_ROCKER_10075676_5020xxxx.indd 11 25.11.2011 14:50:10
LC-22LE240

Operation Manual (Continued)

• Multipartiton support is available. Maximum two


different partitions are supported. If the disk have Connecting to a DVD Player
more than two partitions, crash may occur. First via Component Sockets
partition of the usb disk is used for PVR ready
features. It also must be formatted as primary (YPbPr) or Scart Cable
partition to be used for PVR ready features. • Some DVD players are connected through
• Some stream packets may not be recorded because COMPONENT SOCKETS (YPbPr). In this case,
of signal problems, so sometimes video may freezes you must use the supplied Component video
during playback. connection cable for enabling connection. First,
plug single jack of the cable to the TV’s YPbPr
• Record, Play, Pause, Display (for PlayListDialog) socket (side). Afterwards, insert your component
keys could not be used when teletext is ON. If a cable’s (not supplied) connectors into the socket
recording starts from timer when teletext is ON, part of the Component video connection cable (see
teletext is automatically turned off. Also teletext illustration below). Colours of the connected jacks
usage is disabled when there is ongoing recording should match.
or playback.
• To enable audio connection, use the VGA/Component
• Radio record is not supported. Audio cable. First, plug single jack of the cable
• The TV can record programmes up to ten hours. to the TV. Afterwards, insert your DVD player’s
audio cable’s connectors into the socket part of the
Connecting to a DVD Player via HDMI VGA/Component audio connection cable (see
Please refer to your DVD player’s instruction book illustration below). Colours of the connected jacks
for additional information. Power off both the TV and should match.
the device before making any connections. Side view

Note: Not all cables shown in the illustration are


supplied. YPbPr
DVD Player
YPbPr Video Cable
Connection Cable
• If your DVD player has an HDMI socket, you can (supplied)
(Not supplied)

connect via HDMI for better video and audio quality.


• When the connection is made, switch to
YPbPr source. See, Input selection section.
1

HDMI Cable Note: To connect YPb Pr device, you should use supplied
VGA
SPDIF (not supplied) component (YPbPr) connection cable
Coax.OUT
• You may also connect through the SCART input.
1

SCART

External device
VGA
SPDIF

• When you connect to DVD player as illustrated above,


switch to the connected HDMI source. See, Input Coax.OUT

Selection section for more information on changing


sources. SCART

Scart Cable
(not supplied)

External device

• Note: These three methods of connection perform the


same function but in different levels of quality. It is not
necessary to connect by all three methods.

English - 12 -

A01_MB62_[GB]_1910UK_IDTV_TC_PVR_BRONZE19_22942LED_ROCKER_10075676_5020xxxx.indd 12 25.11.2011 14:50:10

13
LC-22LE240

Operation Manual (Continued)

Connecting the LCD TV to a PC Remote Control Handset


For displaying your computer’s screen image on your Inserting Batteries
LCD TV, you can connect your computer to the TV set.
• Remove the battery cover located on the back of
Power off both computer and display before making
the handset by gently pulling backwards from the
any connections. Use 15-pin D-sub display cable to
indicated part.
connect a PC to the LCD TV. When the connection
is made, switch to PC source. See “Input selection” • Insert two AAA/R3 or equivalent type batteries
section. Set the resolution that suits your viewing inside. Observe the correct polarity (+/-) when
requirements. Resolution information can be found inserting batteries and replace the battery cover.
in the appendix parts
PC VGA Cable
(not supplied)

PC Input
(back) or
Side Audio/Video
Connection Cable
(supplied)

Note: Remove the battery from remote control


SIDE AV

PC Audio Cable handset when it is not to be used for a long period.


.
Side AV Input
(not supplied)
Otherwise it can be damaged due to any leakage of
batteries. Remote range is approximately 7m/23ft.
Using Side AV Connectors
Switching On/Off
You can connect a range of optional equipment to your
LCD TV using side connectors of the TV. To Switch the TV On
• For connecting a camcorder or camera , you should Connect the power cord to the 220-240V AC 50 Hz.
use AV socket (side). To do this, you must use the • Switch the “ ” button on the bottom right hand
supplied video/audio connection cable. First, plug side under the screen to position “|” so the TV will
single jack of the cable to the TV’s AV IN socket switch to standby mode. Then the standby LED
(side). Afterwards, insert your camera cable’s (not lights up.
supplied) connectors into the plural part of the video/
• To switch on the TV from standby mode either:
audio connection cable. Colours of the connected
jacks should match. See illustration below. • Press the “ ” button, CH / CH or a numeric
• Afterwards, you should switch to Side AV source. See button on the remote control.
the section Input selection in the following sections • Press the “ ” or +/- button on the TV.
for more information. • The TV will then switch on.
AV Connection AV Cable
Cable (supplied) (not supplied) Note: If you switch on your TV via CH / CH buttons
on the remote control or on the TV set, the programme
SIDE AV

that you were watching last will be reselected.


By either method the TV will switch on.

Headphone
Camera To Switch the TV to Standby
To switch the TV to low power stand by press the
• To listen the TV sound from headphones, you
“ ” button on the remote control or right hand side
should connect headphones to your TV by using the
of the TV.
HEADPHONE jack as illustrated above..
Note: When the TV is switched to standby mode,
standby LED can blink to indicate that features such
as Standby Search, Over Air Download or Timer is
active.
To Switch the TV Off
• Switch the “ ” button on the bottom right hand
side under the screen to position 2 as illustrated,

to isolate the TV from the mains, the LED will


go out.

English - 13 -

A01_MB62_[GB]_1910UK_IDTV_TC_PVR_BRONZE19_22942LED_ROCKER_10075676_5020xxxx.indd 13 25.11.2011 14:50:11

14
LC-22LE240

DIMENSIONS

LC-22LE240K

Dimensional Drawings

Specications
TV BROADCASTING
PAL/SECAM B/G D/K K’ I/I’ L/L’
RECEIVING CHANNELS
VHF (BAND I/III)
UHF (BAND U)
HYPERBAND
NUMBER OF PRESET CHANNELS
1000
CHANNEL INDICATOR
On Screen Display
RF AERIAL INPUT
75 Ohm (unbalanced)
OPERATING VOLTAGE
220-240V AC, 50Hz.
AUDIO
German + Nicam Stereo
AUDIO OUTPUT POWER (WRMS.) (10% THD)
2 x 2,5
POWER CONSUMPTION (W)
45 W (max)
< 0,5 W (Standby)
PANEL
16:9 display, 22” (55 cm) Screen Size
DIMENSIONS (mm)
DxLxH (With foot): 149 x 534,6 x 377,4
Weight (Kg): 4,3
DxLxH (Without foot): 35 x 534,6 x 352,4
Weight (Kg): 3,7

MHEG-5 ENGINE compliant with IS


Object carousel support compliant with
Frequency range: 474-8
170-862 MHz
Digital
Reception Transmission standard:
Demodulation: COFDM
FEC: all D
15 Video: MP@M
Audio: MPEG Laye
LC-22LE240

INTRODUCTION

0. INTRODUCTION

17MB62 mainboard is driven by MStar SOC. This IC is capable of handling Video and
audio processing, Scaling-Display processing, 3D comb filter, OSD and text processing,
LVDS transmitting, channel and MPEG2/4 decoding, integrated DVB-T/C demodulator
and media center functionality.

TV supports PAL, SECAM, NTSC colour standards and multiple transmission standards
as B/G, D/K, I/I’, and L/L’ including German and NICAM stereo. Also DVB T, DVB-C are
supported internal demoulators of Mstar IC and DVB-S/S2 is supported with externall
demodulator.

Sound system output is supplying max. 2x2,5W ( less 10%THD at max output) with 4Ω
speakers or 2x6W for stereo 8Ω speakers.

Supported peripherals are:

1 RF input VHF I, VHF III, UHF @ 75Ohm(Common)


1 Side AV (CVBS, R/L_Audio)
1 SCART socket(Common)
1 YPbPr (Optional)
1 PC input(Common)
2 HDMI 1.3 input(1 HDMI input is common, 1 input is optional)
1 S/PDIF output(Optional)
1 Headphone(Optional)
1 Common interface(Common)
1 USB(Common)
1 DVD(Optional)
1 On-board Keypad(Optional)
1 External Keypad(Optional)
1 External TouchPad(Optional)

16
LC-22LE240

0.1 General Block Diagram


.1. General Block Diagram

17
LC-22LE240

0.2. MB62 Placement of Blocks

YPbPr SAV HP
USB Keypad
Sat
Demod Nand
Flash
(U162) Speaker
Satellite Tuner Con.
CI Connector
0.2 MB62 Placement of Blocks

Tuner(T3
)

SCART

18
Connec
Main IC
External tor
Keyboard (U5)
Touchboard HDMI VGA
Connectors Led
Con

DVD
Connector DDR2
LVDS SPI Inv.
RAM Adapter DC Con
(U155) Flash
Connectors Input SPDIF
Out
Power Connector
LC-22LE240

CIRCUIT DESCRIPTIONS

1. TUNER(TU3)
A horizontal mounted and Digital Half-Nim tuner is used in the product, which covers 3
Bands(From 48MHz to 862MHz for COFDM, from 45.25MHz to 863.25MHz for CCIR CH).
The tuning is available through the digitally controlled I2C bus (PLL). Below you will find
info about the tuner.

In active antenna option, the following circuit are used. ANT_CTRL pin is controlled by
microcontroller. If ANT_CTRL is low, ANT_PWR will be low. If ANT_CTRL is high,
ANT_PWR will be high.

OVER_CUR_DETECT pin is a monitor for short circuit in antenna. OVER_CUR_DETECT


is low, ANT_CTRL will be low, so ANT_PWR will be low. Finally, short circuit protection is
done by circuits and microcontroller.

1.1. General description of Sony RE216:


The SUT-RE216 is designed for terrestrial TV (digital & analog) and digital cable
reception. It includes a full band tuner and a channel filtering for digital signals. It provides
a low IF output after channel filtering to drive a channel demodulator. Tuning, band
switching and initialization are made via an I2C bus
interface. The module is built on a low-loss printed
circuit board carrying all the components in a metal
housing frame with top and rear covers. The single
aerial connector is mounted on one frame side and all
other connections are made via pins at the bottom.

Features:

 Full frequency range from 47 to 870 Mhz


 Digital Platform (DVB-T/T2, DVB-C, ISDB-T & ATSC)
 Analog platforms (PAL B/G/I/D/K, NTSC M & SECAM L/L’)
 Low IF tuner concept

19
LC-22LE240

 Programmable channel Filter bandwidth



 Fully I2C bus controlled
Programmable channel Filter bandwidth

 For Hybrid TV controlled
Fully I2C bus applications
 For Hybrid TV applications

---Pinning Table

and Application Block Diagram of Tuner---

20 AZAD2102(U163, U164)
2. AUDIO AMPLIFIER STAGE WITH
2.1. General Description
LC-22LE240

and Application Block Diagram of Tuner---

2. AUDIO AMPLIFIER STAGE WITH AZAD2102(U163, U164)


2.1. General Description
17MB62 uses two 2,5W Class D Mono Audio Amplifers for from 16” to 24” TVs.
AZAD2102B is a 2.9 Watts (max. can offer 3.0 Watts @ Load = 3Ω,THD=10%,
AVdd=DVdd=5.5Volt)with high efficiency filter-free class-D audio power amplifier in a
1613 mm x 1613 mm wafer chip scale package (WCSP). AZAD2102B uses Current-
switch technology to achieve high performance class-d amplifier that features 0.03%
THD, 85% efficiency, –70 dB PSRR, to improve RF-rectification immunity.

AZAD2102B provide a Vibration-Spectrum modulation clock for PWM Output. This


vibration frequency is around 10KHZ shift (+/- 5KHZ of Fpwm).

The advantage of the small size package (WCSP) makes AZAD2102B very suitable for
mobile phone and PDA device application. And the Class-D amplifier structure let
AZAD2102B to have highly efficiency power consumption than Class-AB amplifier.
AZAD2102B can shrink the application board, reduce system cost, and external
components.

ESD level protection I/O embedded in AZAD2102B. For general applications, doesn’t
need to add extra ESD protection device (like Varistors) in application system for
AZAD2102B’s I/O.
2.2. Features
 CMOS Technology
 High Efficiency 85%
 High PSRR 70dB at 217Hz
 Differential OP-amp Input
 AZAD2102B provides Vibration-Spectrum Modulation clock for reduce EMI
 Provide Mute function(set Mute_B to GND will go into Mute status)
 For the input stage AZAD2102B built-in a 10Kohm resistors (Gain setting=29.5dB)
 Maximum Battery Life and Minimum Heat
 Efficiency With an 8-Ω Speaker:
 3.5 mA Quiescent Current
 Output Power at 10% THD
 2.85Watts at AVdd=DVdd=5.0Volt, Rload=4Ω
 1.45Watts at AVdd=DVdd=3.6Volt, Rload=4Ω
 0.30Watts at AVdd=DVdd=3.0Volt, Rload=4Ω
 1.75Watts at AVdd=DVdd=5.5Volt, Rload=8Ω
 0.87Watts at AVdd=DVdd=3.6Volt, Rload=8Ω
 0.41Watts at AVdd=DVdd=3.0Volt, Rload=8Ω
 Eliminate Power on and Power-off “Pop” noise
 A Fewer External Components
 Optimized PWM Output Stage Eliminates LC Output Filter
 Internally generate 290 kHz Switching Frequency to eliminate Capacitor and
Resistor
 Improve PSRR (–70 dB) and Wide Supply Voltage (3.0 V to 5.5 V)
 Fully Differential Design Reduces RF Rectification
 This chip has been built-in a very strong ESD protection.
 System level ESD 4KV (IEC 61000-4-2 ESD Contact Level)
 Wafer Chip Scale Package (WCSP)
 TSSOP Package with Exposed Pad

21
LC-22LE240

2.3. Absolute Ratings

2.3.1. Electrical Characteristics

22
LC-22LE240

2.3.2. Operating Specifications

2.4. Pinning

23
3. AUDIO AMPLIFIER STAGE WITH TPA3113(U168)
LC-22LE240

3. AUDIO AMPLIFIER STAGE WITH TPA3113(U168)


3.1. General Description
17MB62 uses a 6W Class D Mono Audio Amplifers for from 26” to 32” TVs. The
TPA3113D2 is a 6-W (per channel) efficient, Class-D audio power amplifier for driving
bridged-tied stereo speakers. Advanced EMI Suppression Technology enables the use of
inexpensive ferrite bead filters at the outputs while meeting EMC requirements.
SpeakerGuard™ speaker protection circuitry includes an adjustable power limiter and a
DC detection circuit. The adjustable power limiter allows the user to set a "virtual" voltage
rail lower than the chip supply to limit the amount of current through the speaker. The DC
detect circuit measures the frequency and amplitude of the PWM signal and shuts off the
output stage if the input capacitors are damaged or shorts exist on the inputs.

The TPA3113D2 can drive stereo speakers as low as 4 Ω. The high efficiency of the
TPA3113D2, 87%, eliminates the need for an external heat sink when
playing music.

The outputs are also fully protected against shorts to GND, VCC, and output-to-output.
The short-circuit protection and thermal protection includes an auto-recovery feature.
3.2. Features
 6-W/ch into an 8-Ω Loads at 10% THD+N From a 10-V Supply
 12-W into a 4-Ω Mono Load at 10% THD+N From a 10-V Supply
 87% Efficient Class-D Operation Eliminates Need for Heat Sinks
 Wide Supply Voltage Range Allows Operation from 8 V to 26 V
 Filter-Free Operation
 SpeakerGuard™ Speaker Protection Includes Adjustable Power Limiter plus DC
Protection
 Flow Through Pin Out Facilitates Easy Board Layout
 Robust Pin-to-Pin Short Circuit Protection and Thermal Protection with Auto
Recovery Option
 Excellent THD+N / Pop-Free Performance
 Four Selectable, Fixed Gain Settings
 Differential inputs

3.3. Absolute Ratings

3.3.1. Electrical Characteristics

24
LC-22LE240

3.3.2. Operating Specifications

3.4. Pinning

25
60R C1007
60R C1081 C997 C1005 C1070 100nF
10uF 100nF 100nF 100nF 16V
6V3 16V 16V 16V
LC-22LE240 AVSS_PGA

F271

F295
A3V3_STBY AVDD_3V3

1k
60R C1030 C1024 C1025 C1022
10uF 100nF 100nF 100nF
6V3 16V 16V 16V 60R 402 ferrite secilecek

F305
F272 2V5_VCC AVDD2V

4. POWER STAGE
1V8_VCC AVDD_DDR C1028 1k C1009 C1223
60R C990 100nF 100nF 10uF 100nF 100nF
22uF 6V3 16V 16V
6V3 16V 16V
F306
C1004 C1001 AVDD2V
The DC voltages required at various parts of the chassis and panel are provided1k
byC1008
a
100nF
C1224
100nF
main power supply unit.3V3_VCC
MB62 chassis can operate
F270
VDD_3V3
with IPS60, IPS16, IPS17, PW26,
F307 16V 16V
AVDD2V
PW27 as main power supply and60Ralso with
C1029 12V
C1014 adaptor. 1k C1221

ìò ĞÑÉÛÎ ÍÌßÙÛ 10uF


6V3
100nF
16V F308
100nF
16V
B
CN706 is used for IPS60, IPS16 and IPS17 and CN1 is used for PW26 and PW27.
1k
AVDD2V
C1222 C1225
100nF 100nF
̸» Üİ ª±´¬¿¹»­ ®»¯«·®»¼ ¿¬ ª¿®·±«­ °¿®¬­ ±º ¬¸» ½¸¿­­·­ ¿²¼ °¿²»´ ¿®» °®±ª·¼»¼ 16V
¾§ ¿ 16V

³¿·² °±©»® ­«°°´§ «²·¬ò ÓŞêî ½¸¿­­·­ ½¿² ±°»®¿¬» ©·¬¸ ×ĞÍêğô ×ĞÍïêô ×ĞÍïéô ĞÉîêô
ĞÉîé ¿­ ³¿·² °±©»® ­«°°´§ ¿²¼ ¿´­± ©·¬¸ ïîÊ ¿¼¿°¬±®ò
POWER SOCKET
22uF
16V

İÒéğê ·­ «­»¼ º±® ×ĞÍêğô ×ĞÍïê ¿²¼ ×ĞÍïé ·­ «­»¼ º±® ĞÉîê ¿²¼ ĞÉîé,17PW80,17PW07ò
C7

20 19

3V3_VCC 18 17 3V3_VCC

3V3_STBY 16 15 VDD_AUDIO_PWR

12V_VCC/STBY 14 13 12V_VCC/STBY
C
5V_VCC 12 11 5V_VCC

12V_VCC/STBY 10 9 5V_STBY

22uF
16V

C6
8 7 DIMMING

6 5 BACKLIGHT_ON/OFF

4 3 STBY_ON/OFF
S7
2 1

CN706 S8
VDD_AUDIO_PWR
MEGA_DCR_OUT
JK9 is used for the adapter option and also CN705 inverter socket or DB32 chassis with
CN706 is used to supply backlight. NC

S17
D
S16
BACKLIGHT_DIM

S18
MEGA_DCR_IN

NC
ÖÕç ·­ «­»¼ º±® ¬¸» ¿¼¿°¬»® ±°¬·±² ¿²¼ ¿´­±S10İÒéğë ·²ª»®¬»® ­±½µ»¬ ±® ÜŞíî ½¸¿­­·­ ©·¬¸
12V_VCC/STBY
İÒéğê ·­ «­»¼ ¬± ­«°°´§ ¾¿½µ´·¹¸¬ò 12V_VCC

S19
12V_STBY

3V3_VCC

S21
12V_VCC/STBY 12V_VCC
The power supplies Egenerate 18V, 12V, 5V, 3,3V and 12V, 5V, stand by mode DC
S22
voltages. Power stage which is on-chassis generates 5V, 3V3 stand by voltage and 12V,
12V_STBY 5V_VCC

8V, 5V, 3V3, 2.5V, 1,8V and 1,2V supplies for other different parts of the chassis. Chassis
12V_VCC
block diagram is indicated below.

̸» °±©»® ­«°°´·»­ ¹»²»®¿¬» ïèÊô ïîÊô ëÊô íôíÊ ¿²¼ ïîÊô ëÊô ­¬¿²¼ ¾§ ³±¼» Üİ
ª±´¬¿¹»­ò б©»® ­¬¿¹» ©¸·½¸ ·­ ±²ó½¸¿­­·­ ¹»²»®¿¬»­ ëÊô íÊí ­¬¿²¼ ¾§ ª±´¬¿¹» ¿²¼ ïîÊô
èÊô ëÊô íÊíô îòëÊô ïôèÊ ¿²¼ ïôîÊ ­«°°´·»­ º±® ±¬¸»® ¼·ºº»®»²¬ °¿®¬­ ±º ¬¸» ½¸¿­­·­ò ݸ¿­­·­
¾´±½µ ¼·¿¹®¿³ ·­ ·²¼·½¿¬»¼ ¾»´±©ò
F

PANEL_VCC_ON/OFF

1 26 2 3
LC-22LE240

6 7 8
1 2 3 4 5 6
ADAPTER SOCKET FS3
W_ADAPTER 1 2
12V_STBY

TP239
!
5 7A/32VDC

POWER BLOCK DIAGRAM


W/ADAPTOR
4 FS2
1 2
12V_INV
1

3 7A/32VDC
JK9
4

6
A

TP243
12V_S

DC/DC1
FDC604P
2

Q1
1
SW1 C1038 SW2
A

1
1
TP243

TP36 F9 100nF 5V_VCC


12V_STBY 12V_VCC U174
3

1
1 2

12V_VCC C1112 5V_STBY


MP1583

6
60R 10nF DC-DC4
2

16V
F287 0R 1 BS 8
1

16V SS R1972

FDC604P
2 IN EN 7

1
12V_STBY

Q198
1 2 2 1
12V_STBY 10k R1709

C1047

220nF

R1729
3 SW COMP 6

33k
60R
C1091 C1092 C1037 R1690 3k9
1 2
25V
22uF 100nF 4 GND DC FB 5 1V2_VCC 1 2
4

22uF

1
1 2
10k
1

5n6F
16V 16V 16V
DC-DC1 DC

2
R1722
FDC642P

50V
5V_VCC

1
NC C1130 1
47R
2
Q2

CCFL INVERTER SOCKET

R1737

R1728
DC 5V_STBY
4

33k

1k
F7
3

1 2
5V_VCC
DC 60R
FDC604P

CN705
B SW2 L118 F6
Q198

3
1 2
1 12V_INV 1 2
5V_STBY R1698
1 TP37 15uH C1102 C1103 5V_VCC 60R MOSFET_CONTROL
2
10k 1 2
Q184
BC848B

2
2 22uF 22uF
LDO2

D197

SS33
16V 16V
1

3
DC-DC2 3V3_TUN
722 INVERTER SOCKET W/ADAPTER

1
1 TP39
LDO
3

2
4
7R S1
5 DIMMING DC 3V3_STBY
6
S6
BACKLIGHT_ON/OFF DC
SW3
1

W/ADAPTOR & W/IPS16&17&60&PW25


3V3_VCC
TP45
TP46

B
C
SW1
DC-DC3
DC/DC2 SW3

C1036
100nF
FS5

TP238

10V
1 2
12V_VCC F10 30068939
8B 12V_STBY 7A/32VDC 12V_VCC
1 2

C1114 DC 1 BS
1V8_VCC 3V3_STBY
SS 8
4

60R 2

1
4A 10nF
F286 16V
1
DC U23 R1689
FDC642P

1
2 IN EN 7
1

1
12V_STBY
Q200

1 2 2 1
12V_STBY 10k
C1049

220nF

R1732

C1048

220nF

R1731
2

2
25V

33k

25V

33k
60R C1089 C1090 MP1484 C1129 R1708
3 SW COMP 6
22uF 22uF LDO1 5k6
1

1
1 2

16V 16V 3N3 R3


2

2
R1724 5n6F R1723
4 GND FB 5 2V5_VCC
3

1
47R
2

50V 6k8 1
47R
2

LDO
1
R1733

R1730
33k

10k
for 3v3 Panel Sup.

R1735

TP244
22k
L123 NC F12
1 2
2

1 2
3V3_VCC
15uH 60R
3 3

R1692 L16 F11 R1697

1
Q182 Q183
D
The blocks on power block diagram is using dependent to main supply. For PW26 and PW27
2 1 2 2

MOSFET_CONTROL
2
10k
1
3V3_STBY MOSFET_CONTROL
2
10k 1

BC848B 10uH 60R BC848B


C1096 C1097
1 1
22uF 22uF
6V3 6V3

just common blocjs are enough for proper operation


7&60&PW25&PW06 COMMON
SW3 FS4
C
DC/DC4
E 1 LDO12 3
DC/DC3
1

4 3V3_VCC
2

5 6 7

C1035
100nF
10V
R1738 R1769
3V3_STBY
ADAPTER SOCKET U175 3V3_STBY 7A/32VDC 20k 100k
30068939
4

LM1117 C1113
F303 FS3 2
1 BS SS 8

1
W_ADAPTER 12V_STBY
10nF
3 IN OUT 2
1 2
C1107
2A U173
1 2 1

5V_VCC 2V5_VCC R1770 F273 16V R1691

!
TP241
TP239

7A/32VDC 6 EN FB 1 2 IN EN 7
FDC604P

5 60R 150k
1 2
12V_VCC
POWER BLOCK DIAGRAM
2 1
C1033 12V_VCC 10k
C1080

100uF

GND VOUT
1
1

2
6V3

U176 60R MP1484


Q197

22uF C1131 R1710

W/ADAPTOR
150K C1085 C1084 5V_V
R1721

FS2 1uF
C1048

220nF

R1731

100R

4 1 4 5 VIN
6V3
12V_INV GND 2 10UH 22uF 22uF 3 SW COMP 6 1
3k9
2
2

1 2
6V3
2

25V

33k
1

1 2

7A/32VDC F291 MP2012 L116 16V 16V R1686


1

JK9 3 5n6F
SW1
4

A 3V3_VCC 1 2 4 PVIN SW 3 1V8_VCC 4 GND FB 5 39k


1

TP243

12V_STBY 50V 12V_VCC

DC/DC1 10uH
Q1 1

60R
FDC604P

2 1
100R 2 R1768 DC-DC4
R1720 C1093 C1094 C1101 C1098 1k
SW2
2

1 R1723 22uF 22uF C1038 22uF 22uF DC 1V2_VCC

TP231
3

6V3 6V3 6V3 6V3 DC-DC1 DC


R1736
TP36 1 2 F9 100nF 5V_VCC
47R 12V_VCC U174
22k
3

1 2

C1112 5V_STBY
NC MP1583 DC 5V_STBY
4

60R 10nF
2

16V
S89 F287 0R 16V 1 BS 1
SS 8
R1972 L117 DC
6 FDC604P

STBY_ON/OFF
1
2 IN 7 SW2
1

12V_STBY
Q198

1 2
EN
1

7 R2 2

R3 3
5 R4 4

2 1
12V_STBY 10k R1709
R1730

C1047

220nF

R1729

1V2_VCC
R1979

3 SW 6 5V_VCC
2

33k

60R
100R

C1091 C1092 C1037 COMP R1690 3k9


1 2
25V 10uH
10k

R1

1 2

22uF 100nF 4 GND 5 C1087 C1086


4

S83 22uF FB
1

1 2
10k 5n6F
F STBY_ON/OFF_NOT MOSFET_CONTROL
16V 16V 16V 22uF DC-DC2
22uF
2

R1722
FDC642P

50V
38

6V3 6V3
NC C1130 1
47R
2
Q2

DC 3V3_STBY
DC
CCFL INVERTER SOCKET
R1737

R1728

C1217

10nF

SW3
33k

50V
1k

F7
3V3_VCC
3

1 2
5V_VCC
3 60R
CN705
B R1697 L118
1
F6
2
3
DC-DC3
1 12V_INV 1 2
5V_STBY R1698
Q183 15uH C1102 60R Q184
D
2
2
10k 1 2
TP37 C1103 10k
MOSFET_CONTROL
2 1
1
MOSFET_CONTROL
BC848B DC
2

2 22uF 22uF
BC848B
D197

SS33

16V 16V
1 DC
1 2 3 4 5 6
For IPS16, IPS17, IPS60 below blocks must work properly
3
INVERTER SOCKET W/ADAPTER 1 LDO1
1

1 TP39
4
S1 LDO
5 DIMMING
S6
6 BACKLIGHT_ON/OFF
1

W/ADAPTOR & W/IPS16&17&60&PW25&PW06


TP45
TP46

C
SW1 DC/DC2 SW3
C1036
100nF

FS5 FS4
TP238

10V

1 2
12V_VCC F10 30068939
1 2
3V3_VCC
1 2

12V_STBY 7A/32VDC 12V_VCC C1114 3V3_STBY 7A/32VDC


1 BS SS 8
4

60R 2
2

4A 10nF
2A
U23
1

F286 16V R1689


FDC642P

FDC604P
1

2 IN EN 7
1

12V_STBY
Q200

Q197

1 2 2 1
12V_STBY 10k
C1049

220nF

R1732

C1048

220nF

R1731
2

2
25V

33k

25V

33k

60R C1089 C1090 MP1484 C1129 R1708


22uF 22uF 3 SW COMP 6 5k6
1

1 2

16V 16V 3N3 R3


2

R1724 5n6F R1723


4 GND FB 5
3

1
47R
2

50V 6k8 1
47R
2

/DC4
1
R1733

R1730
33k

10k

for 3v3 Panel Sup.


R1735

TP244
22k

L123 NC F12
1 2
2

1 2
3V3_VCC
15uH 60R
3 3

R1692 L16 F11 R1697


1

Q182 Q183
D
2 1 2 2

MOSFET_CONTROL
2
10k
1
3V3_STBY MOSFET_CONTROL
2
10k 1

BC848B 10uH 60R BC848B


C1096 C1097

LDO2 E
C1035
100nF

1 1
22uF 22uF
6V3 6V3
10V

939

SS 8
2

73 R1691
U2 AP211H
LM1117
484
EN 7

COMP 6
2
10k
C1131 R1710
12V_VCC

1
1

For adopter case also 2


3 COMMON
5V_VCC below blocks are INnecessary
OUT 2
1
F300

330R
2

DC/DC4
3V3_TUNER
3k9 C1212
C1079

ADJ VOUT C1034


DC/DC3
22uF

1 2
6V3

E 5n6F R1686
LDO1 22uF 100nF
LDO2
C1035
100nF

FB 5 1 4 1

39k 6V3 10V 30068939


10V

R1738 R1769
50V U175
LM1117
3V3_STBY 20k 100k C1113
1 BS SS 8
R1768 3 IN
2

F303
2

10nF
5V_VCC
1
OUT 2
2

2V5_VCC C1107 R1770 F273 16V


1

U173 R1691
U2 AP211H
TP241

6 EN LM1117
60R FB 1 2 IN EN 7
1k 12V_VCC
1 2

C1033 150k 12V_VCC


2
10k
1
F300
C1080

100uF

GND VOUT

27
1

3 IN OUT 2
2
6V3

22uF U176 60R C1085 C1084 MP1484 C1131 R1710 5V_VCC


1 2

150K
R1721

1uF
100R

1 4 6V3 5 VIN GND 2 10UH


100R 22uF 22uF 3 SW COMP 6 3k9
1 2 330R C1212
2

C1079

6V3 ADJ VOUT


22uF

1 2
TP231

6V3

L116 1 2
F291 MP2012 16V 16V R1686 22uF
1

5n6F
3V3_VCC 1 2 4 PVIN SW 3 R25
1V8_VCC 4 GND FB 5 39k 1 4 6V3
1
R1736

60R 10uH 50V


100R R1768
22k

1 2

R1720 C1093 C1094 C1101 C1098 1k


22uF 22uF 22uF 22uF 100R
1

TP231

1 2

6V3 6V3 6V3 6V3 R25


R1736
00R

22k
24

NC
1
1

S89
00R
24

STBY_ON/OFF L117
1
LC-22LE240
3 4 5 6

12V_STBY

12V_INV

W/ADAPTOR

TP243
12V_STB

DC/DC1
C1038 SW2

1
F9 100nF 5V_VCC
1 2 U174
12V_VCC C1112 5V_STBY
MP1583

6
60R
6 7 8
2

10nF 16V
F287 0R 16V 1 1
BS SS 8
R1972

FDC604P
2 7

1
12V_STBY

Q198
1 2

12V_STBY IN EN 2
10k
1
R1709

C1047

220nF

R1729
3 6

33k
60R
C1091 C1092 C1037 SW COMP R1690 3k9
1 2
25V
1 2

22uF 22uF 100nF 4 GND FB 5

1
1 2
10k 5n6F
16V 16V 16V

2
50V R1722

1
C1130 1
47R
2
M12
N12
P12
R12
D13
E13
F13
G13
H13
J13
K13
L13
M13
N13
P13
R13
D14
E14

L14
M14
N14
P14
R14
D15

33k K15

GND65 L15
GND66 M15
GND67 N15
GND68 P15
GND69 R15
GND70 D16
GND71 K16
GND72 L16
GND73 M16
GND74 D17
GND75 K17
GND76 L17
GND77 M17
GND78 K18
GND79 L18
GND80 M18

GND87 D18
GND81 W2
GND82 W3
GND83 V4
GND841k V5
GND85 V6

GND86 D9
R1737

R1728
F7
GND40
GND41
GND42
GND43
GND44
GND45
GND46
GND47
GND48
GND49
GND50
GND51
GND52
GND53
GND54
GND55
GND56
GND57

GND58
GND59
GND60
GND61
GND62
GND63

GND64
1 2
5V_VCC
60R
L118 F6 3
1 2
1 2
5V_STBY R1698
A
MSD9WB9PT-2

15uH C1102 C1103 60R MOSFET_CONTROL


2
10k 1 2
Q184
BC848B
2

22uF 22uF
D197

SS33

16V 16V
1
6

AVDD_CVBS33_0
AVDD_CVBS33_1
AVDD_ALIVE_2

/ADAPTER
U5

1
AVDD_DMPLL

AVDD_EAR33

AVDD_DDR_0
AVDD_DDR_1
AVDD_DDR_2
AVDD_DDR_3
AVDD_DDR_4
AVDD_AU33

G15 AVDD_LPLL

BYPASS
G16 VDDP0
G17 VDDP1

W/ADAPTOR & W/IPS16&17&60&PW25


E15
E16
E17
F16
F17
G8

G9

E9
F9

J8

H8

K9
Short CCT Protection Circuit
1uF

FS5 Short circuit protection is necessary for protecting chassis C974 and main IC against damages DC/DC2 6V3
SW3
C1036
100nF
VDD_3V3

AVDD_DDR
TP238

7A/32VDCwhen 12V_VCC
any Vcc60Rsupply shorts to1 ground.8 Protect pin should be logic high while normal
10V

1
12V_VCC
2
F10 30068939
AVDD_3V3

1 2

C1114 3V3_STBY
5

4
operation. When F286 there is16Va short circuit protect pin shold be logic low. After any short
2

BS SS
2

4A 10nF
U23
1

R1689
FDC642P

2 IN EN 7

1
detection, SW forcesC1089LEDsC1090
on LED card to blink.
12V_STBY
Q200

1 2 2 1
12V_STBY 10k

C1048

220nF

R1731
B

25V

33k
60R MP1484 C1129 R1708
3 6 22uF 22uF SW COMP 5k6

1
1 2

16V 16V 3N3 R3

2
5n6F R1723
4 GND FB 5
2

3
50V 6k8 1
47R
2

R1730
10k
for 3v3 Panel Sup.
R1735

TP244

R1649
22k

L123 NC F12
33k 3V3_VCC VDD_AUDIO_PWR
1 2 2 1
1 2

15uH 60R
3
2

L16 F11 R1697


10k
1

BAW56

Q183
D185

1 2 2
1
3V3_STBY
2
MOSFET_CONTROL
2
10k 1

10uH
C1096 C1097 60R R1631 BC848B
SHORT CCT PROTECTION
3
1
22uF 22uF R1727
6V3 6V3 2
33k 12V_VCC 1
1

R1750
22k
3V3_STBY
3V3_VCC
2

R1635
BAW56
D186

COMMON
2 1
10k 3
PROTECT

5V_VCC C
1

DC/DC4
TP202

3V3_TUNER
DC/DC3
2

1
C1035
100nF

R1636 ADAPTOR OVER VOLTAGE PROTECTION


BAW56
D184

10V

R1738 R1769 Q180 30068939


1
10k
2
R40
1

3V3_STBY 20k 100k BC858B 2 3


C1113 2
1 BS 20k
SS 8 12V_STBY
2

10nF
C C1107 R1770 3
F273 16V
1

U173R21 R1691
Q178
1

C971
TP241

6 EN 2FB
1 3
150k
1 2 2 IN EN 7 2
12V_VCC
1
12V_VCC 10k
100nF
U176 R1638
150K 2 R20
60R C1085 C1084 MP148410k C1131 R1710 5V_VCC
1uF 5 2 10UH 3 SW COMP 6
1 2
VIN10V GND 22uF3V3_STBY
1 1 2
6V3 10k 10k 22uF 1 2 3k9
1 2

F291 MP2012 L116 16V 16V 3 R1686


1

4 PVIN 5n6F
3V3_VCC SW 3 BC848B 1V8_VCC U7 4 VCC FB 5
1 2
2

1 GND 50V 39k


60R 10uH Q211
R1639

3
LM809 RST GND R1768
10k

C1093 C1094 C1101 C1098 1k


22uF 22uF 22uF 22uF 2
R1973 2 1
TP231

6V3 6V3 6V3 6V3


R1736

100R
1

22k

BC848B
1

L117
1
1

7 R2 2

6 R3 3

5 R4 4

1V2_VCC
R1979
100R

10uH
R1

C1087 C1086
ET_CONTROL 22uF 22uF
8

6V3 6V3
D
LNB CIRCUIT
C1217

10nF
50V

1N4001

C70 10V C69 D7


470nF 220uF 1uF
3 25V 4 C65 50V 5 6
28
R42
2k2
4k7
R41

15nF C68
SK24
D8

50V

L2 27 V_UP VO_TX 22
LC-22LE240

4.1. Power Management

---MB62 Power Management with Adaptor---

---MB62 Power Management with PW25/ PW26---

29
LC-22LE240

---MB62 Power Management with IPS16/IPS17/IPS60/PW05---

---MB62 Power Management with PW03/PW04/PW07---

30
LC-22LE240

5. MICROCONTROLLER – MSTAR(U5)
5.1. Description

MSD9WB9PT-2 (Main IC) (U5)

The MSD9WB9PT-2 is MStar’s most up-to-date system-on-chip solution for flat panel
integrated digital television products. Building on the success of MStar’s preceding SOC
series, the MSD9WB9PT-2 provides most cost-effective solution for DTV application with
creative and attractive features exclusively presented by MStar.
The MSD9WB9PT-2 integrates DTV/multi-media all-purpose AV decoder, DVB-T
demodulator, VIF demodulator, and Sound/Video processor into a single device. This
allows the overall BOM to be reduced significantly making the MSD9WB9PT-2 a very
competitive multi-media DTV solution. For ATV users, the MSD9WB9PT-2 provides multi-
standard analog TV support with adaptive 3D video decoding and VBI data extraction.
The build-in audio decoder is capable of decoding FM, AM, NICAM, A2, BTSC and EIA-J
sound standards. The MSD9WB9PT-2 supplies all the necessary A/V inputs and outputs
to complete a receiver design including a multi-port HDMI receiver and component video
ADC. All input selection multiplexed for video and audio are integrated, including full
SCART support with CVBS output. The equipped MStar MACE-5 color engine is the
latest masterpiece from
MStar famous color engine series providing excellent video and picture quality in Full-HD
and large-scale displaying system.
To meet the increasingly popular energy legislative requirements without the use of
additional hardware, the MSD9WB9PT-2 has an ultra low power standby mode during
which an embedded MCU can act upon standby events and wake up the system as
required.

The MSD9WB9PT-2 is composed of several modules:

High Performance Micro-processor


 Ultra high speed/performance 32-bit RISC CPU
 One full duplex UARTs
 Supports USB and ISP programming
 DMA Engine
Transport Stream De-multiplexer
 Supports parallel and serial TS interface, with or without sync signal
 Supports TS input and output for external CI module
 Maximum TS data rate is 104 Mb/sec for serial or 16 MB/sec for parallel
 32 general purpose PID filters and section filters for each transport stream de-
multiplexer
 Supports additional audio/video/PCR filters
 Supports TS DMA channel for time-shift
 Supports 3DES/DES and AES encryption/decryption
MPEG-2 Video Decoder
 ISO/IEC 13818-2 MPEG-2 video MP@HL
 Automatic frame rate conversion
 Supports resolution up to HDTV (1080i, 720p) and SDTV

31
LC-22LE240

MPEG-4 Video Decoder


 ISO/IEC 14496-2 MPEG-4 ASP video decoding
 Supports resolutions up to HDTV (1080p@30fps)
 Supports DivX1 Home Theater & HD profilesOptional
 Supports VC-1Optional, FLV video format decoding
Hardware JPEG
 Supports sequential mode, single scan
 Supports both color and grayscale pictures
 Following the file header scan the hardware decoder fully handles the decode
process
 Supports programmable Region of Interest (ROI)
 Supports formats: 422/411/420/444/422T
 Supports scaling down ratios: 1/2, 1/4, 1/8
 Supports picture rotation
NTSC/PAL/SECAM Video Decoder
 Supports NTSC-M, NTSC-J, NTSC-4.43, PAL (B,
 D, G, H, M, N, I, Nc), and SECAM standards
 Automatic standard detection
 Motion adaptive 3D comb filter
 Five configurable CVBS & Y/C S-video inputs
 Supports Teletext, Closed Caption (analog CC 608/ analog CC 708/digital CC
608/digital CC
708), V-chip and SCTE
Multi-Standard TV Sound Processor
 SIF audio decoding
 Supports BTSC/A2/EIA-J demodulation
 Supports NICAM/FM/AM demodulation
 Supports MTS Mode Mono/Stereo/SAP in BTSC/ EIA-J mode
 Supports Mono/Stereo/Dual in A2/NICAM mode
 Built-in audio sampling rate conversion (SRC)
 Audio processing for loudspeaker channel, including volume, balance, mute, tone,
EQ,virtual stereo/surround and treble/bass controls
 Advanced sound processing options available,for example: SRS1, BBE2,
QSound3, Audyssey4
 Supports digital audio format decoding:
MPEG-1, MPEG-2 (Layer I/II), MP3, Dolby Digital (AC-3), AAC-LC
SupportsOptional Dolby Digital Plus, Dolby mPulse, and MS10 multistream
decoder, including Dolby Digital Encoder for transcoding streams to Dolby Digital
5.1 (DDCO)
 Supports MPEG Audio, Dolby Digital, Dolby Digital Plus format AD (Audio
Description)
 Supports PVR and time-shifting
Audio Interface
 One SIF audio input interface with minimal external saw filters
 Four L/R audio line-inputs
 Two L/R outputs for main speakers and additional line-outputs
 Supports stereo headphone driver

32
LC-22LE240

 I2S digital audio input & output


 S/PDIF digital
I2S digital audioaudio
inputoutput
& output
 HDMI audio channel processing
S/PDIF digital audio output
 Programmable HDMI audio channeldelay processing
for audio/video synchronization
Analog RGB Compliant Input Port
 Programmable delay for audio/video synchronization
 Three
Analog RGB analog
Compliant ports support
Input Port up to 1080P
 Supports PC RGB input
Three analog ports support up to
upSXGA@75Hz
to 1080P
 Supports HDTV RGB/YPbPr/YCbCr
Supports PC RGB input up to SXGA@75Hz
 Supports Supports Composite Sync and SOG Sync-on-Green
HDTV RGB/YPbPr/YCbCr
 Automatic color calibration
Supports Composite Sync and SOG Sync-on-Green
 AV-link Automaticsupport
color calibration
Analogue RGB Auto-Configuration & Detection
 AV-link support
Analogue  AutoRGB inputAuto-Configuration
signal format and mode detection
& Detection
 Auto-tuning function
Auto input signal including
format phasing,
and mode positioning, offset, gain, and jitter detection
detection
 Sync Detection for H/V Sync
Auto-tuning function including phasing, positioning, offset, gain, and jitter detection
DVI/HDCP/HDMI Compliant Input Port
 Sync Detection for H/V Sync
 Two HDMI/DVI
DVI/HDCP/HDMI Input ports
Compliant Input Port
 HDMI 1.3 Compliant
Two HDMI/DVI Input ports
 HDCPHDMI 1.31.1Compliant
Compliant
 225MHz @ 1080P 60Hz input with 12-bit Deep-color support
HDCP 1.1 Compliant
 CEC support
225MHz @ 1080P 60Hz input with 12-bit Deep-color support
 Single link
CEC support DVI 1.0 compliant
 Robust receiver
Single link DVI 1.0 with excellent long-cable support
compliant
 Robust receiver with excellent long-cable support
MStar Advanced Color Engine (MStarACE-5)
 10/12-bit
MStar Advancedinternal data processing
Color Engine (MStarACE-5)
 Fully
10/12-bit internal data processing scaling engine
programmable multi-function
Nonlinear video scaling supports various modes including Panorama
 Fully programmable multi-function scaling engine
Supports dynamic scaling for VC-1
Nonlinear video scaling supports various modes including Panorama
 High-Quality DTV
Supports video processor
dynamic scaling for VC-1
3D motion video deinterlacer with motion object stabilizer
 High-Quality DTV video processor
Edge-oriented deinterlacer with edge and artifact smoother
3D motion video deinterlacer with motion object stabilizer
Automatic 3:2/2:2/M:N pull-down detection and recovery
Edge-oriented deinterlacer with edge and artifact smoother
3D multi-purpose noise reduction for DTV or lousy air/cable input
Automatic 3:2/2:2/M:N pull-down detection and recovery
MPEG artifact removal including de-blocking and mosquito noise reduction
3D multi-purpose noise reduction for DTV or lousy air/cable input
Arbitrary frame rate conversion
MPEG artifact removal including de-blocking and mosquito noise reduction
 MStar A Professional
rbitrary framePicture Enhancement:
rate conversion
Dynamic brilliant and fresh color
 MStar Professional Picture Enhancement:
Dynamic Blue Stretch
Dynamic brilliant and fresh color
Intensified contrast and details
Dynamic Blue Stretch
Dynamic Vivid Skin
Intensified contrast and details
Dynamic sharpened Luma/Chroma edges
Dynamic Vivid Skin
Global and local dynamic depth of field perception
Dynamic sharpened Luma/Chroma edges
Accurate and independent color control
Global and local dynamic depth of field perception
Supports sRGB and xvYCC color processing
Accurate and independent color control
Supports HDMI 1.3 deep color format
Supports sRGB and xvYCC color processing
 Programmable Supports12-bit HDMIRGB gamma
1.3 deep CLUT
color format
 Programmable
Output Interface 12-bit RGB gamma CLUT
 Single/dual link 8/10-bit LVDS output
 Supports panel resolution up to Full-HD (1920x1080) @ 60Hz
 Supports TH/TI format
 Supports dithering options to 6/8-bit output
 Spread spectrum output for EMI suppression
33
CVBS Video Encoder
 Supports all NTSC/PAL TV Standard
Output Interface
LC-22LE240 Single/dual link 8/10-bit LVDS output
 Supports panel resolution up to Full-HD (1920x1080) @ 60Hz
Output Interface
 Supports TH/TI format
 Single/dual link 8/10-bit LVDS output
 Supports dithering options to 6/8-bit output
 Supports panel resolution up to Full-HD (1920x1080) @ 60Hz
 Spread spectrum output for EMI suppression
CVBS Supports TH/TI format
Video Encoder
 Supports
Supports dithering options
all NTSC/PAL TVtoStandard
6/8-bit output
 Spread spectrum output
Stand-alone scaling engine for EMI suppression
CVBS Video Encoder
 Programmable Hue, Contract, Brightness
 Supports all NTSC/PAL TV Standard
 Supports TTX/CC/WSS output
CVBS  Stand-alone
Video Outputscaling engine
 Programmable
Allows CVBS output Hue, Contract, Brightness
of all source inputs
2DGraphicsSupports TTX/CC/WSS output
Engine
CVBS Video Output
 Hardware Graphics Engine for responsive
 Allows CVBS output of all source inputs
Interactive applications
2D Graphics Engine
 Supports point draw, line draw, rectangle draw/fill, text draw and trapezoid draw
 Hardware Graphics Engine for responsive
 BitBlt, stretch BitBlt, trapezoid BitBlt, mirror BitBlt and rotate BitBlt
 Interactive applications
 Raster Operation (ROP)
 Supports point draw, line draw, rectangle draw/fill, text draw and trapezoid draw
 Support Porter-Duff
BitBlt, stretch BitBlt, trapezoid BitBlt, mirror BitBlt and rotate BitBlt
VIF Demodulator
 Raster
CompliantOperation (ROP)
with NTSC M/N, PAL B, G/H, I, D/K,
 Support Porter-Duff
SECAM L/L' standards
VIF Demodulator
 Audio/Video dual-path processor
 Compliant with NTSC M/N, PAL B, G/H, I, D/K,
 Stepped-gain PGA with 25 dB tuning range and 1 dB tuning resolution
 SECAM L/L' standards
 Maximum IF gain of 37 dB
 Audio/Video dual-path processor
 Programmable TOP to accommodate different tuner gain and SAW filter insertion
 Stepped-gain
loss to PGA with 25 dB tuning range and 1 dB tuning resolution
 Maximum
optimize noise andoflinearity
IF gain 37 dB performance
 Programmable TOP to accommodate
Multi-standard processing different tuner gain and SAW filter insertion
with single SAW
loss to
 Supports silicon tuner low IF output architecture
optimize noise and linearity performance
 Multi-standard processing with single SAW
 Supports silicon tuner low IF output architecture
DVB-T Demodulator
 Digital carrier frequency offset correction: ±500KHz
 Optimised for SFN channels with pre/post-cursive echoes inside/outside the guard
DVB-T Demodulator
 Acquisition range ±857kHz includes up to 3x ±1/6 MHz transmitter offset
 Digital carrier frequency offset correction: ±500KHz
 Meets Nordig Unified 1.0.3, D-Book 5.0, EICTA E-Book/C-Book test requirement
 Optimised for SFN channels with pre/post-cursive echoes inside/outside the guard
 ±400kHz internal carrier offset recovery range
 Acquisition range ±857kHz includes up to 3x ±1/6 MHz transmitter offset
 6.8 usecs echo cancellation at 7 Msym/s
 Meets Nordig Unified 1.0.3, D-Book 5.0, EICTA E-Book/C-Book test requirement
 Supports IF, low-IF, zero-IF inputs
 ±400kHz internal carrier offset recovery range
 Ultra-fast automatic blind UHF/VHF channel scan (constellations and symbol rate)
 6.8 usecs echo cancellation at 7 Msym/s
Connectivity
 Supports IF, low-IF, zero-IF inputs
 Ultra-fast
Two USB automatic blind UHF/VHF channel scan (constellations and symbol rate)
2.0 host ports
Connectivity
 USB architecture designed for efficient support of external storage devices in
 conjunction
Two USB 2.0 with
host ports
off air broadcasting
Miscellaneous
 DRAM interface supporting one 16-bit DDR2 @1066MHz
 Supports PVR
 Supports Common Interface for conditional access support
 Bootable SPI interface with serial flash support
 Parallel interface for external NAND flash support
 Power control module with ultra low power MCU available in standby mode
 380-ball LFBGA package
 Operating Voltages: 1.26V (core), 1.8V (DDR2), 2.5V and 3.3V (I/O and analog)

34
5.2. MSTAR Block Diagram
? Bootable SPI interface with serial flash support

C121

16V
10n
? Parallel interface for external NAND flash support
LC-22LE240
? Power control module with ultra low power MCU B3available
USB0_DPin standby mode
A3
? 380-ball LFBGA package W8
USB0_DM
USB1_DP
? Operating Voltages: 1.26V (core), 1.8V (DDR2),
USB_DP
Y82.5V and 3.3V (I/O and analog)
USB_DM USB1_DM
J9 GND0
H9 GND1
5.2. MSTAR Block Diagram

LED SOCKET

CN703
1

5
1
TP56
TP57 5V_STBY
D TP54 1
1

1
F259
2
TP53 IR_IN

R1940
1

150R
C949 600R
1 2

TP55 1
27pF
Q170 50V
BC848B
3

2
2
R1563

R1571

R1562
220R

2
10k

10k
2

R1572
220R
1
Q171
R1567
10k

1
BC848B
1

R1568
10k
1
3 3

Q174
2 2

Q173
BC858B BC858B
LED2

1 1

LED1
2

2
R1569

R1570
220R

220R

E
5.3. Reset Circuit
1

Reset circuit using for initiliazing main Mstar IC. Reset condition is high and nomal
5V_STBY
working condition is low for RESET pin.
PANEL VCC = 5V/12V

RESET
R1668
4

3V3_STBY 1k 3
C1016

100nF
16V

TP61

2
C1031

22uF
6V3

1
1

RESET CN1

F
1N4148
R1667

C1015
D189

10k

100nF
1

10V 5V_VCC 1

6. CI INTERFACE 3V3_VCC 4k7 3


R1198

CI Interface Power Switch: 35


It is used for CI module supply, when Module is inserted (it means CI detect is low)2
1 This
circuit is opened or closed by CI_POWER_CTRL port of main uController
A6 SDO LVA2P AA13 TX_A_2_P
A7 GPIO14 LVA2M Y13 TX_A_2_N
LVACKP AA12 TX_A_CLK_P
LC-22LE240 LVACKM W12 TX_A_CLK_N
LVA3P W11 TX_A_3_P
K6 DDCA_CK/UART0_RX LVA3M Y12 TX_A_3_N KEYBOARD_ONBOARD C630
M6 DDCA_DA/UART0_TX LVA4P W10 TX_A_4_P
2

100nF
LVA4M Y11 TX_A_4_N F248
1

10V
R793
U5 1
47R
2 1 2

KEYBOARD
MSD9WB9PT-2 R1959 TOUCH_PAD_OPTION F249 600R
H19 S76
DDCR_CK 4 1
4k7
2
3V3_STBY 1 2
3V3_STBY

6. CI INTERFACE
H20 DDCR_DA GPIO137 Y9 600R
HP_MUTE
SPDIFI/GPIO139 W7
DVD_SPDIF R1937
GPIO141 AA10 100R HP_DETECT MECH_SWITCH 1 2
47R SCL_SYS
GPIO143 Y10 R1954 CI_POWER_CTRL R1936
A4 IRIN R1952 1 2
47R SDA_SYS
CI Interface Power Switch: 4k7 3V3_VCC
1 2

CN709
1

6
Y6 XIN
It is usedGPIO10
for CI B7
module supply, when Module is inserted (it means CI detect is low) This
STBY_ON/OFF_NOT
AA6 XOUT circuit is opened
GPIO11 or
E6
F6
closed by CI_POWER_CTRL
LED1 port of main uController
EXT KEYPAD
GPIO7 LED2
1

1
R1617

R1672

E5 R1671
4k7

4k7

4k7
HWRESET
SINGLE
16V

B3
3V3_STBY

3V3_STBY

3V3_STBY

USB0_DP

PANEL_VCC
A3 USB0_DM

OP_PIN11

OP_PIN8

OP_PIN9
W8 USB1_DP
Y8 USB1_DM
J9

2
GND0
H9

S14

S13
S3
GND1

1
ONBOARD KEYBOARD
OCKET

CN138
TP10

10

11
1

9
1
4

1
TP56
D204

B5V1

KEYBOARD_ONBOARD
TP57 5V_STBY
1
F259
470R
R23

R45
10k

CN137
2k
R7

1 2

IR_IN
C949 600R

4
1 2
+ -
27pF
50V 7. USB INTERFACE
4

Main Concept IC has integrated 2 USB 2.0 interface. One of them is used for ethernet
3

function, the other one is used for USB connectivity


SW5 for last user. Last user can play video,
R1571

R1562
2

10k

2
R1572

picture and audio files. Also digital channels can be record


E2 E1
to externall storage device by
220R

Q171
this interface. All SW files can be updated with interface.
1
BC848B
R1568
10k

G4

G3

G2

G1
1

174
USB circuit has 3 main parts
2

Q173
1 BC858B  Integrated USB 2.0 Host3 interface of D3K (U5)
BUTTONS KEYBOARD OPTION
LED1

 Protection IC (U145)
OP_PIN43
OP_PIN42
2
R1569

R1570
220R

 Over Curent Protection IC (U8)


PANEL_VCC

TX_B_4_P
TX_B_4_N
TX_B_3_P
TX_B_3_N
1

5V_STBY
PANEL VCC = 5V/12V USB INTERFACE
TP6

T R844
1

4 6 IO4 IO1 1 1 2
10R USB_DP
U145
USB

51
50
49
48
47
46
45
44
43
42
41
40
39
38
37

3 5 VDD GND 2
AZ099-04S R845
OP_PIN45

OP_PIN43
OP_PIN42
TP59 TP60
1

4 IO3 IO2 3
TP61

2 1
10R
2
USB_DM

1
1

C610
1

RESET CN1 10uF 1


TP7
10V
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35

5V_VCC 1 VIN 5
VOUT
U8
2 GND
FPF2124 R46
3V3_VCC 4k7 3 ON ISET 4 560R
R1198

2 3 4
36
LC-22LE240

8. DDR2 SDRAM K4T1G164QF (U155)


8.1 General Description
Description:
The 1Gb DDR2 SDRAM is organized as a 16Mbit x 8 I/Os x 8 banks, 8Mbit x 16 I/Os x 8
banks device. This synchronous device achieves high speed double-data-rate transfer
rates of up to 1066Mb/sec/pin (DDR2-1066) for general applications. The chip is designed
to comply with the following key DDR2 SDRAM fea-tures such as posted CAS with
additive latency, write latency = read latency - 1, Off-Chip Driver(OCD) impedance
adjustment and On Die Termination. All of the control and address inputs are
synchronized with a pair of exter-nally supplied differential clocks. Inputs are latched at
the crosspoint of dif-ferential clocks (CK rising and CK falling). All I/Os are synchronized
with a pair of bidirectional strobes (DQS and DQS) in a source synchronous fash-ion. The
address bus is used to convey row, column, and bank address information in a RAS/CAS
multiplexing style. For example, 1Gb(x8) device receive 14/10/3 addressing. The 1Gb
DDR2 device operates with a single 1.8V ± 0.1V power supply and 1.8V ± 0.1V VDDQ.
The 1Gb DDR2 device is available in 60ball FBGA(x8) and 84ball FBGA(x16).

Features:
8.2 Features

• JEDEC standard VDD = 1.8V ± 0.1V Power Supply


• VDDQ = 1.8V ± 0.1V
• 533MHz fCK for 1066Mb/sec/pin
• 8 Banks
• Posted CAS
• Programmable CAS Latency: 4, 5, 6, 7
• Programmable Additive Latency: 3, 4, 5. 6
• Write Latency(WL) = Read Latency(RL) -1
• Burst Length: 4 , 8(Interleave/nibble sequential)
• Programmable Sequential / Interleave Burst Mode
• Bi-directional Differential Data-Strobe (Single-ended data-strobe is an optional feature)
• Off-Chip Driver(OCD) Impedance Adjustment
• On Die Termination
• Special Function Support - PASR(Partial Array Self Refresh) - 50ohm ODT - High
Temperature Self-Refresh rate enable
• Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95
°C
• All of products are Lead-free, Halogen-free, and RoHS compliant

37
LC-22LE240

Pinning:
8.3 Pinning

38
LC-22LE240

9. SCALER AND LVDS SOCKETS


9.1. LVDS sockets Block Diagram

9.2. Panel Supply Switch Circuit


This switch is used to open and close panel supply of TCON. It is controlled by port of
main ucontroller. Also with this circit panel sequency could be adjusted correctly. 3 panel
supplys are connected to this circuit. All of them are optional according to panels.

39
220pF 7 R2 2
3
50V R1679
LC-22LE240
BACKLIGHT_DIM
S16 1
R1165
4k7
2 2
Q189 6 R3 3
100R DIMMING
BC848B
C838 1 5 R4 4
S18 3

MEGA_DCR_IN 1 2 R1166 C774


1
4k7
2 2
Q188 10uF
NC 220pF BC848B
50V 10V
C840 1

1 2

220pF
50V

F302
1 2
3V3_VCC
60R

TP213
F289
PANEL SUPPLY SWITCH
1 2

60R
F288

1
1 2
5V_VCC PANEL_VCC
60R

6
F290
1 2
12V_VCC

FDC642P
2
60R

Q199
R1734
33k
C1128

1uF
25V
3V3_VCC

3V3 or 5V

1
3V3_S

1
R1725
or 12V
1 2
47R

2
4k7
R1749
22k
2

1
R1678
4k7

3 R1748
NC STBY_ON/OFF_NOT
2
1

1 2

S82 R1693 4k7


1 2 2
10k
1 2
Q190
BC848B 1

3 C1042 2
1

R1685 100nF
PANEL_VCC_ON/OFF
2
10k
1 2
Q194
10V
1

BC848B
1

3 4 5

10. SPI FLASH MEMORY - MX25L1005 (U158)


10.1. General Description
MX25L1005 is a CMOS 1,048,576 bit serial Flash memory, which is configured as
131,072 x 8 internally.The MX25L1005 feature a serial peripheral interface and software
protocol allowing operation on a simple 3-wire bus. The three bus signals are a clock
input (SCLK), a serial data input (SI), and a serial data output (SO). SPI access to the
device is enabled by CS# input. The MX25L1005 provide sequential read operation on
whole chip. After program/erase command is issued, auto program/ erase algorithms
which program/ erase and verify the specified page or sector/block locations will be
executed. Program command is executed on page (256 bytes) basis, and erase
command is executes on chip or sector(4K-bytes) or block(64K-bytes). To provide user
with ease of interface, a status register is included to indicate the status of the chip. The
status read command can be issued to detect completion status of a program or erase
operation via WIP bit. When the device is not in operation and CS# is high, it is put in
standby mode and draws less than 10uA DC current. The MX25L1005 utilize MXIC's
proprietary memory cell, which reliably stores memory contents even after 100,000
program and erase cycles.

10.2. Features
 Serial Peripheral Interface (SPI) compatible -- Mode 0 and Mode 3
 1,048,576 x 1 bit structure
 32 Equal Sectors with 4K byte each, Any Sector can be erased individually
 2 Equal Blocks with 64K byte each, Any Block can be erased individually
 Single Power Supply Operation 40
command is executes on chip or sector(4K-bytes) or block(64K-bytes). To provide user
with ease of interface, a status register is included to indicate the status of the chip.LC-22LE240
The
status read command can be issued to detect completion status of a program or erase
operation via WIP bit. When the device is not in operation and CS# is high, it is put in
standby mode and draws less than 10uA DC current. The MX25L1005 utilize MXIC's
proprietary memory cell, which reliably stores memory contents even after 100,000
program and erase cycles.

10.2. Features
 Serial Peripheral Interface (SPI) compatible -- Mode 0 and Mode 3
 1,048,576 x 1 bit structure
 32 Equal Sectors with 4K byte each, Any Sector can be erased individually
 2 Equal Blocks with 64K byte each, Any Block can be erased individually
 Single Power Supply Operation
 2.7 to 3.6 volt for read, erase, and program operations
 Latch-up protected to 100mA from -1V to Vcc +1V
 Low Vcc write inhibit is from 1.5V to 2.5V

10.3. Absolute Maximum Ratings

RATING VALUE
Ambient Operating 0°C to 70°C
Temperature
Storage Temperature -55°C to 125°C
Applied Input Voltage -0.5v to 4.6v
Applied Output Voltage -0.5v to 4.6v
VCC to Ground Potential -0.5v to 4.6v

10.4. Pinning
8-PIN SOP (150mil)

SYMBOL DESCRIPTION
CS# Chip select
SI Serial Data Input
SO Serial Data Output
SCLK Clock Input
HOLD# Hold, to pause the device without
deselecting the device
VCC +3.3v Power Supply
GND Ground

41
LC-22LE240

11. NAND FLASH MEMORY – NAND512XXA2C (U162)


11.1. General Description
The NAND flash 528-byte/ 264-word page is a family of non-volatile flash memories that
uses the single level cell (SLC) NAND technology. It is referred to as the small page
family.

The NAND512R3A2C, NAND512R4A2C, and NAND512W3A2C have a density of 512


Mbits and operate with either a 1.8 V or 3 V voltage supply. The size of a page is either
528 bytes (512 + 16 spare) or 264 words (256 + 8 spare) depending on whether the
device has a x8 or x16 bus width.

The address lines are multiplexed with the Data Input/Output signals on a multiplexed x8
or x16 input/output bus. This interface reduces the pin count and makes it possible to
migrate to other densities without changing the footprint.

To extend the lifetime of NAND flash devices it is strongly recommended to implement an


error correction code (ECC). The use of ECC correction allows to achieve up to 100,000
program/erase cycles for each block. A write protect pin is available to give a hardware
protection against program and erase operations.

11.2. Features
 High density NAND flash memories
o 512-Mbit memory array
o Cost effective solutions for mass storage applications

 NAND interface
o x8 or x16 bus width
o Multiplexed address/ data

 Supply voltage: 1.8 V, 3 V


 Page size
o x8 device: (512 + 16 spare) bytes
o x16 device: (256 + 8 spare) words

 Block size
o x8 device: (16K + 512 spare) bytes
o x16 device: (8K + 256 spare) words

 Page read/program
o Random access: 12 μs (3 V)/15 μs (1.8 V) (max)
o Sequential access: 30 ns (3 V)/50 ns (1.8 V) (min)
o Page program time: 200 μs (typ)
 Copy back program mode
 Fast block erase: 2 ms (typ)

42
LC-22LE240

 Status register
 Electronic signature
 Chip Enable ‘don’t care’
 Security features
o OTP area

 Serial number (unique ID) option


 Hardware data protection
o Program/erase locked during power transitions

 Data integrity
o 100,000 program/erase cycles (with ECC)
o 10 years data retention

 RoHS compliant packages


 Development tools
o Error correction code models
o Bad blocks management and wear leveling algorithms

11.3. Pinning

43
LC-22LE240

12. LM1117(U175, U180, U181)


12.1. General Description
The LM1117 is a series of low dropout voltage regulators with a dropout of 1.2V at 800mA
of load current. It has the same pin-out as National Semiconductor’s industry standard
LM317. The LM1117 is available in an adjustable version, which can set the output
voltage from 1.25V to 13.8V with only two external resistors. In addition, it is also
available in five fixed voltages, 1.8V, 2.5V, 2.85V, 3.3V, and 5V. The LM1117 offers
current limiting and thermal shutdown. Its circuit includes a zener trimmed bandgap
reference to as-sure output voltage accuracy to within ±1%. The LM1117 series is
available in SOT- 223, TO-220, and TO-252 D-PAK packages. A minimum of 10μF
tantalum capacitor is required at the output to improve the transient response and
stability.

12.2. Features
 Available in 1.8V, 2.5V, 2.85V, 3.3V, 5V, and Adjustable Versions
 Space Saving SOT-223 Package
 Current Limiting and Thermal Protection
 Output Current 800mA
 Line Regulation 0.2% (Max)
 Load Regulation 0.4% (Max)
 Temperature Range
 LM1117 0°C to 125°C
 LM1117I -40°C to 125°C

12.3. Applications
 2.85V Model for SCSI-2 Active Termination
 Post Regulator for Switching DC/DC Converter
 High Efficiency Linear Regulators 15
 32” TFT TV Service Manual 10/01/2005
 Battery Charger
 Battery Powered Instrumentation

12.4. Absolute Maximum Ratings

12.5. Pinning

44
13. MP2012 (U176)
LC-22LE240

13. MP2012 (U176)


13.1. General Description
The MP2012 is a fully integrated, internally compensated 1.2MHz fixed frequency PWM
step-down converter. It is ideal for powering portable equipment that runs from a single
cell Lithium-Ion (Li+) Battery, with an input range from 2.7V to 6V. The MP2012 can
provide up to 1.5A of load current with output voltage as low as 0.8V. It can also operate
at 100% duty cycle for low dropout applications. With peak current mode control and
internal compensation, the MP2012 is stable with ceramic capacitors and small inductors.
Fault condition protection includes cycle-by-cycle current limiting and thermal shutdown.

13.2. Features
 2.7-6V Input Operation Range
 Output Adjustable from 0.8V to VIN
 1μA Max Shutdown Current.
 Up to 95% Efficiency
 100% Duty Cycle for Low Dropout
 Applications
 1.2MHz Fixed Switching Frequency
 Stable with Low ESR Output Ceramic
 Capacitors
 Thermal Shutdown
 Cycle-by-Cycle Over Current Protection
 Short Circuit Protection
 Available in 6-pin 3x3mm QFN

13.3. Pinning

Pin Name Description


#
1 FB Feedback input. An external resistor divider from
the output to GND, tapped to the FB pin sets the
output voltage.
2 GND, Ground pin. Connect exposed pad to ground
Exposed plane for proper thermal performance.
Pad
3 SW Switch node to the inductor.
4 PVIN Input supply pin for power FET.
5 VIN Input Supply pin for controller. Put small
decoupling ceramic near this pin.
6 EN Enable input, “High” enables MP2012. EN is
pulled to GND with 1Meg internal resistor.

45
14. RTA8283A (U23, U173)
5 VIN Input Supply pin for controller. Put small
decoupling ceramic near this pin.
6 EN optimized
decoupling
Enable input, over
ceramic
“High” athis
near wide
enables pin. range
MP2012. EN is of loads and outp
LC-22LE240
6 EN provides
Enable input,
pulled to protection
GND“High” enables
with 1Meg against
MP2012.
internal EN isshorted outputs an
resistor.
pulled to GND with 1Meg internal resistor.
during start-up. The RT8283A also provides ou
shutdown protection. The low current (<3μA) sh
14. RTA8283A (U23, U173)
14. RTA8283A (U23, U173) enabling easy power management in batterypo
14.1. General Description in a SOP-8 package.
The14.1. General
RT8283A is a Description
high-efficiency, monolithic synchronous step-down DC/DC converter
The RT8283A is a high-efficiency,
that can deliver up to 3A output current monolithic
from asynchronous step-down
4.5V to 23V input supply.DC/DC converter
The RT8283A's
that can mode
current deliverarchitecture
up to 3A output 14.2. Features
current from
and external a 4.5V to allow
compensation 23V input supply. The
the transient RT8283A's
response to be
current mode
optimized overarchitecture andofexternal
a wide range loads andcompensation allow the
output capacitors. transient response
Cycle-by-cycle currenttolimit
be
optimized over a wide
provides protection rangeshorted
against of loadsoutputs 
and output ±1.5%
capacitors.
and soft-start High Accuracy
Cycle-by-cycle
eliminates Feedback
currentsurge
input current limit Volta
provides protection
during start-up. Theagainst
RT8283A shorted outputs and
also provides soft-start eliminates input current surge
during start-up.
shutdown The RT8283A
protection. also provides
The low current
output
(<3μA) output
under voltage
Integrated
under
shutdown modevoltage
protection
N-MOSFET
protection
provides
and thermal
outputand
Switches
thermal
disconnect,
shutdown protection.
enabling easy power The low current
management in (<3μA) Current
shutdown
batterypowered Mode
mode provides
systems. Control
output
The RT8283A disconnect,
is available
enabling
in a SOP-8easy power management in batterypowered systems. The RT8283A is available
package.
in a SOP-8 package.  Fixed Frequency Operation : 340kHz
14.2. Features  Output Adjustable from 0.8V to 20V
14.2. Features
 ±1.5% High Accuracy Feedback Voltage
 ±1.5% HighN-MOSFET
Integrated Accuracy Feedback  Up to 95% Efficiency
Switches Voltage
 Integrated Control Switches 
N-MOSFET
Current Mode Thermal Shutdown Protection
 Current Mode Control
Fixed Frequency Operation : 340kHz
 Fixed
OutputFrequency
AdjustableOperation
from 0.8V: 340kHz
to 20V
 Output Adjustable from
Up to 95% Efficiency 0.8V to 20V
 Up to 95% EfficiencyProtection

Thermal Shutdown
Thermal Shutdown Protection
14.3. Pinning
14.3. Pinning
14.3. Pinning

Pin No. Pin Description


Name
1 BOOT Bootstrap for high-side gate driver. Connect a 0.1μF or
greater ceramic capacitor from BOOT to SW pins.
2 VIN Input Supply 4.5V to 23V. Must bypass with a suitably
large ceramic capacitor.
3 SW Phase Node--Connect to external L-C filter..
4, 9 (Exposed GND Ground.
Pad)
5 FB Feedback Input pin is connected to the converter output.
It is used to set the output of the converter to regulate to
the desired value via an internal res divider. For an
adjustable output, an external res divider is connected to
this pin.
6 COMP Compensation Node. COMP is used to compensate the
regulation Control loop. Connect a series RC network
from COMP to GND. In some cases, an additional
capacitor from COMP to GND is required.
7 EN Enable Input Pin. Logic high enables the converter; a
logic low forces the RT8253A into shutdown mode.
Attach this pin to VIN with a 100kΩ pull up resistor for
automatic startup.
8 SS Soft-Start Control Input. SS controls the soft-start period.
Connect a capacitor from SS to GND to set the soft-start
period. A 0.1μF capacitor sets the soft-start period to
13.5ms.

46
15. MP1583 (U174)
8 SS Soft-Start Control Input. SS controls the soft-start period.
Connect a capacitor from SS to GND to set the soft-start
LC-22LE240
period. A 0.1μF capacitor sets the soft-start period to
13.5ms.

15. MP1583 (U174)


15.1. General Description
The MP1583 is a step-down regulator with a built-in internal Power MOSFET. It achieves
3A of continuous output current over a wide input supply range with excellent load and
line regulation. Current mode operation provides fast transient response and eases loop
stabilization. Fault condition protection includes cycle-by-cycle current limiting and thermal
shutdown. An adjustable soft-start reduces the stress on the input source at start-up. The
MP1583 requires a minimum number of external components, providing a compact
solution.

15.2. Features
 3A Output Current
 Programmable Soft-Start
 100mΩ Internal Power MOSFET Switch
 Stable with Low ESR Output Ceramic Capacitors
 Up to 95% Efficiency
 20μA Shutdown Mode
 Fixed 385KHz Frequency
 Thermal Shutdown
 Cycle-by-Cycle Over Current Protection
 Wide 4.75V to 23V Operating Input Range
 Output Adjustable from 1.22V to 21V
 Under-Voltage Lockout

15.3. Pinning

Pin Pin Description


No. Name
1 BOOT High-Side Gate Drive Bootstrap Input. BS supplies the drive for the
high-side N-Channel MOSFET switch.
2 IN Power Input. Drive IN with a 4.75V to 23V power source.
3 SW Power Switching Out is the switching node that supplies power to the
output
4 GND Ground.
5 FB Feedback Input. FB senses the output voltage and regulates it. Drive
FB with a resistive voltage divider from the output voltage. FB
threshold is 1.222V.
6 COMP Compensation Node is used to compensate the regulation control
loop.
7 EN Enable/UVLO. A voltage greater than 2.71V enables operation. For
complete low current shutdown the EN pin voltage needs to be at less
than 900mV. When the voltage on EN exceeds 1.2V, the internal
regulator will be enabled and the soft-start capacitor will begin to
charge. The MP1583 will start switching after the EN pin voltage
reaches 2.71V.
8 SS Soft-Start Control Input. SS controls the soft-start period.

47

16. FDC642
than 900mV. When the voltage on EN exceeds 1.2V, the internal
regulator will be enabled and the soft-start capacitor will begin to
LC-22LE240 charge. The MP1583 will start switching after the EN pin voltage
reaches 2.71V.
8 SS Soft-Start Control Input. SS controls the soft-start period.

16. FDC642
16.1. General Description
This P-Channel 2.5V specified MOSFET is produced using Fairchild’s advanced
PowerTrench® process that has been especially tailored to minimize on-state resistance
and yet maintain low gate charge for superior switching performance.

These devices have been designed to offer exceptional power dissipation in a very small
footprint for applications where the larger packages are impractical.

16.2. Features
 Max rDS(on) = 65 mΩ at VGS = -4.5 V, ID = -4.0 A
 Max rDS(on) = 100 mΩ at VGS = -2.5 V, ID = -3.2 A
 Fast switching speed
 Low gate charge (11nC typical)
 High performance trench technology for extremely low rDS(on)
 SuperSOTTM-6 package: small footprint (72% smaller than standard SO-8);
low profile (1 mm thick)
 Termination is Lead-free and RoHS Compliant

16.3. Pinning

17. FDC604P
17.1. General Description
This P-Channel 1.8V specified MOSFET uses Fairchild’s low voltage PowerTrench
process. It has been optimized for battery power management applications.

17.2. Features
 –5.5 A, –20 V. RDS(ON) = 33 mΩ @ VGS = –4.5 V
 RDS(ON) = 43 mΩ @ VGS = –2.5 V
 RDS(ON) = 60 mΩ @ VGS = –1.8 V
 Fast switching speed.
 High performance trench technology for extremely low RDS(ON)(S)

17.3. Pinning
48
LC-22LE240

17. FDC604P
17.1. General Description
This P-Channel 1.8V specified MOSFET uses Fairchild’s low voltage PowerTrench
process. It has been optimized for battery power management applications.

17.2. Features
 –5.5 A, –20 V. RDS(ON) = 33 mΩ @ VGS = –4.5 V
 RDS(ON) = 43 mΩ @ VGS = –2.5 V
 RDS(ON) = 60 mΩ @ VGS = –1.8 V
 Fast switching speed.
 High performance trench technology for extremely low RDS(ON)(S)

17.3. Pinning

18. CONNECTORS
18.1. SCART (SC1)

18.2. HDMI (CN707,CN708)

49
LC-22LE240

18.2. HDMI (CN707,CN708)

18.3. VGA (CN711)

50
LC-22LE240

SERVICE MENU SETTINGS

19. SERVICE MENU SETTINGS

In
4. order to reach
Adjustment service menu, first press “ MENU ”, then press the remote control
instruction
code
In order two times,
to reach servicewhich “ 4725
menu,is First “ “MENU” Then press the remote control code two times, which i
Press
“4725”.In first screen following item can be seen:

In first screen following items can be seen:

51
LC-22LE240

19.1. Video Settings


19.1 Video Setting

19.2. Audio Settings


19.2 Audio Settings

52
LC-22LE240

19.3. Options
19.3 Options
Options-1

Options-1

Options-2
Options-2

53
LC-22LE240
19.4. Tuning Settings

19.4 Tuning Settings

19.5. Source Settings


19.5 Source Settings

54
LC-22LE240

19.6 USB Operations


USB operations option can not be used directly. It can be used for updating panel tool,
hw configuration etc.

55
LC-22LE240

19.7. USB Operations


SOFTWARE
USB operations option can not be used directly. ItUPDATE
can be used for updating panel tool, hw
congiguration etc.

20. SOFTWARE UPDATE


In MB62 project there is only one software. From following steps software update
procedure can be seen:

1.1. MB62
MB62_en.bin, mboot.binand
en. bin, mboot.bin andusb_auto_update_mb62.txt
usb_auto_update_T4.txt documents
documents should copy
should copydirectly
directly
inside of a flash memory(not in a folder).
2. inside of flash
Put flash memory
memory to the( not in a folder).
tv when tv is powered off.
2.3. Put
Powerflash
onmemory
the andto thewhen
wait TV when TVisisopened.
the tv powered off.
4. If First Time Installition screen
3. Power on the TV by main switch and press comes, it means software
OK in remote update
control procedure is during 3 -4
continuously
succesful.
seconds. Then led will start blinking (red / green) quickly.
4. If First Time installation screen comes, it means software update procedure is successful.

56
LC-22LE240

TROUBLESHOOTING

21. TROUBLESHOOTING
21.1. No Backlight Problem
Problem: If TV is working, led is normal and there is no picture and backlight on the panel.

Possible couses: Backlight pin, dimming pin, backlight supply, stby on/off pin

Backlight pin should be high in open position. If it is low, please check Q181 and panel
cables.

Dimming pin should be high or square wave in open position. If it is low, please check
S16 for Mstar side and panel or power cables, connectors.

Backlight power supply should be in panel specs. Please check CN705 for MB62, related
connectors for power supply cards.

57
LC-22LE240

STBY_ON/OFF should be low for standby on condition, please check R1677.

21.2. CI Module Problem


Problem: CI is not working when CI module inserted.
Possible
Possiblecauses:
couses:Supply,
Supply,supply controlpin,
suply control pin,detect
detectpins,pins,mechanical
mechanicalpositions
positionsofofpins
pins
CI
CIsupply
supplyshould be5V
shoul be 5Vwhen
whenCICImodule
moduleinserted.
inserted.If Ifit itisnot
not 5V
5V please
please check
CI_POWER_CTRL, this
CI_POWER_CTRL, this pin
pin should
should be
be low.
low.

58
LC-22LE240

Please check mechanical positions of CI module.

Please check mechanical


Detect ports should positions
be low. If itof
is CI
not module.
low please check CI connector pins, CI module pins
and 3V3_VCC on MB62.
Detect ports should be low. If it is not low please check CI connector pins, CI module pins
and 3V3_VCC on MB62.

59
LC-22LE240

21.3. Led Blinking Problem


Problem: LED blinking, no other operation

This problem indicates a short on Vcc voltages. Protect pin should be logic high while
normal operation. When there is a short circuit protect pin will be logic low. If you detect
logic low on protect pin, unplug the TV set and control voltage points with a multimeter to
find the shorted voltage to ground.

21.4. IR Problem
Problem: LED or IR not working
Check LED card supply on MB62 chasis.

60
LC-22LE240

21.4. IR Problem
Problem: LED or IR not working
Check LED card supply on MB62 chasis.

21.5. Keypad Touchpad Problems


Problem: Keypad or Touchpad is not working

Check keypad supply and KEYBOARD pin on MB62.

61
LC-22LE240

21.5. Keypad Touchpad Problems


Problem: Keypad or Touchpad is not working

Check keypad supply and KEYBOARD pin on MB62.

21.6. USB Problems


Problem: USB is not working or no USB Detection.

Check USB Supply, It should be nearly 5V.

21.7. No Sound Problem


62
Problem: No audio at main TV speaker outputs.
LC-22LE240

21.7. No Sound Problem


Problem: No audio at main TV speaker outputs.

Check supply voltages of VDD_AUDIO, 5V_VCC and 3V3_VCC with a voltage-meter.


There may be a problem in headphone connector or headphone detect circuit (when
headphone is connected, speakers are automatically muted). Measure voltage at
HP_DETECT pin, it should be 3.3v.

21.8. No Sound Problem at Headphone


Problem: No audio at headphone output.

Check
Check HPHP detect
detect pin,
pin, when
when headphone
headphone is
is.connected. Check
Check 5V_VCC 5V_VCC
and andwith
3V3_VCC 3V3_VCC
a voltage-
meter.
with a voltage meter.

21.9. Standby On/Off Problem


Problem:
63
Device cannot boot, TV hangs in standby mode.
LC-22LE240

21.9. Standby On/Off Problem


Problem:
Device cannot boot, TV hangs in standby mode.

There may
There be be
may a problem
a problem about power
about powersupply. Check
supply. Check12V_VCC,
12V_VCC, 5V_VCC
5V_VCCandand
3V3_VCC
3V3_VCC
withwith
a voltage-meter. Also there may be a problem about SW. Try to update
a voltage-meter. Also there may be a problem about SW. Try to update TV withTV with latest SW.
latest
SW. Additionally
Additionally it is goodittoischeck
gooodSW to printouts
check SW via printouts via hyper-terminal
hyper-terminal (or Teraterm).(or Teraterm).
These printouts may give a clue about the problem.
These printouts may give a clue about the problem.

DVD Problems
Problem: DVD is not working.
21.10. No Signal Problem
Check that
Problem: No DVD
signalsource is selected in Service menu. Check supply voltage of DVD
in TV mode.
namely 12V_VCC.
Check tuner supply voltage; 3V3_TUN. Check tuner options are correctly set in Service
menu. Check AGC voltage at IF_AGC pin of tuner.

64
LC-22LE240
MB62 / PW80 OVERALL WIRING DIAGRAM
22. OVERALL WIRING DIAGRAM
LC -22LE 240E / LC -22LE 240E V
MODE L
LC -22LE 240K / LC -22LE 240R U
P ANE L T -C ON B OAR D
MAIN B OAR D MB 62

P O W E R S UP P LY P W 80

P L107 P L703 C N706 C N139


1 V in 1 N.C . 1 G ND 1 P ANE L_V C C
2 V in P L706 2 N.C . 2 G ND 2 P ANE L_V C C
3 B K L_O N/O F F 1 12V _V C C 3 N.C . 3 S T B Y _O N_O F F 3 P ANE L_V C C
4 DIMMING 2 12V _V C C 4 N.C . 4 G ND 4 O P _P IN9
5 G ND DC CABLE 3 B AC K LIG HT _O N_O F F 5 N.C . 5 B AC K LIG HT _O N_O F F 5
6 G ND 4 DIMMING 6 N.C . 6 G ND 6 G ND
5 G ND 7 12V _V C C 7 DIMMING 7 G ND
Part Code 30071426 6 G ND 8 12V _V C C 8 G ND 8 T X _A_3_P

P L105 9 5V _V C C 9 5V _S T B Y 9 T X _A_3_N
1 C hannel_3 10 5V _V C C BOARD TO BOARD 10 12V _V C C /S T B Y 10 T X _A_C LK _P
2 C hannel_11 11 5V _S T B Y SOCKETS 11 5V _V C C 11 T X _A_C LK _N
3 C hannel_12 12 N.C . 12 5V _V C C 12 T X _A_2_P
4 C hannel_10 13 DIMMING 13 12V _V C C /S T B Y 13 T X _A_2_N
5 C hannel_5 14 G ND 14 12V _V C C /S T B Y 14 G ND
6 C hannel_8 15 B AC K LIG HT _O N_O F F 15 V DD_AUDIO _P W R 15 T X _A_1_P
16 G ND 16 3V 3_S T B Y 16 T X _A_1_N
17 S T B Y _O N_O F F 17 3V 3_V C C 17 G ND
FFC INVERTER CABLE Part Code 30070373

18 G ND 18 3V 3_V C C 18 T X _A_0_P
19 G ND 19 G ND 19 T X _A_0_N
20 G ND 20 G ND 20 T X _B _3_P
21 T X _B _3_N
22 T X _B _C LK _P
23 T X _B _C LK _N
P W 80 P OW E R B OAR D 24 G ND
C ON08 Part Code 23036094 LVDS CABLE 25 T X _B _2_P
26 T X _B _2_N
C ONV E R T E R
27 T X _B _1_P
B OAR D 28 T X _B _1_N
P L701 P L700 29 T X _B _0_P
30 T X _B _0_N

MB 62 MAIN B OAR D

ROCKER
SOCKET AC SWITCH
POWER
P ANE L PLUG
C N710
INV E R T E R
1 G ND C N703
B OAR D 2 R _AUDIO _P 1 G ND
SPEAKER CABLE 3 L_AUDIO _P 2 LE D 2
Included on speakers 4 L_AUDIO _P 3 LE D 1
5 L_AUDIO _N 4 IR _IN
6 G ND 5 5V _S T B Y

LE D IR B OAR D

1 G ND
2 LE D 2 Included in Led Board
3 LE D 1 LED/IR CABLE
4 IR _IN
5 5V _S T B Y

S P E AK E R R IG HT S P E AK E R LE F T

65
LC-22LE240

SCHEMATIC DIAGRAMS
23 . Schematic Diagrams
Tuner & T2 Demodulator Diagram
I 1 2 3 4 5 6 7 8

ACTIVE_ANT_SUPPLY
NUTUNE/SEMCO/LG

5V_VCC
C965
C904 2
C61 100nF
1 TP48 100nF 22uF 16V
ANT-DC 1 ANT-DC 1 10V
1
6V3
ACTIVE_ANT_SUPPLY

TH1

2R1
R1595
2 2
A VCC 3V3_TUNER +3V3 3V3_TUNER TUN_SCL 10k 12V_VCC
IF_AGC_MST
R1597 R1963 A
10k 1
100R
2
IF_AGC_TUNER
TU1

TU3
SCL 3 SCL 3 47R TUN_SCL_MST F304 R1581
TUN_SCL 2
C912 2
C910
R30 ACTIVE_ANT_SUPPLY 1k 100nF 100nF
H SDA 4
TUN_SDA SDA 4 47R TUN_SDA_MST 1k FDN336P
Q175 R1590
1

10V
1

10V
R29 R1594 Q172 10k ANT_CTRL
5 5 BC848B

SUT-RE216

10k
R4
GND GND TUN_SDA OVER_CUR_DETECT 10k
FK1601

CLK_OUT 6 RESET 6 RESET_TUNER

R1586

R1593
20k

10k
7 7 S40
IF_N DIGITAL_IF_N IF_N DIGITAL_IF_N
8 8 S41
IF_P DIGITAL_IF_P IF_P DIGITAL_IF_P

IF_AGC 9 IF_AGC 9
IF_AGC_TUNER IF_AGC_TUNER
1
TP47
SONY TUNER
G
B B

F1

1V25_S2_VDDI

3V3_S2_VDDD

1V25_S2_VDDI
1V2_VCC 1V25_S2_VDDI
100nF10V

100nF10V

100nF10V

100nF10V

100nF10V

100nF10V

100nF10V

100nF10V

100nF10V

60R C60
C 22uF C
C36

C37

C44

C45

C46

C47

C48

C49

C50

16V

33pF
NC NC NC NC NC

C35

50V

64

63

62

61

60

59

58

57

56

55

54

53

52

51

50

49
F2
3V3_VCC 3V3_S2_VDDD
10V100nF

E
C38

100nF10V

100nF10V

100nF10V

60R C71

NC5

GPO

VCC_10

NC4

NC3

VDDD_4

NC2

NC1

NC9

NC8

LOCK

VCC_9

LNB_EN

CKXTAL_13

OLF

GNDD
C59
22uF
D206

C5V6

4
3
C39

C40

C43

6V3 R26

27MHz
27 MHZ KULLANILACAK 1 48 12pF

X3
GNDA_1 M_CKOUT 47R 50V TSMICLK
R27
2 47

1
2
XTAL_IN M_SYNC 47R TSMISYNC
3 46

C34
XTAL_OUT VCC_8 1V25_S2_VDDI

33pF
50V
3V3_S2_VDDA R28
3V3_S2_TUN

3V3_S2_TUN

4 45
C22

C8

C9
50V 50V VDDA_1 M_VAL 47R TSMIVALID
27pF

27pF

10pF

10pF
C21

5 44 NC
D F4 16V GNDA_2 M_ERR D
3V3_VCC 3V3_S2_TUN X1 C29 10nF
6 43
100nF10V

100nF10V

100nF10V

100nF10V

100nF10V

100nF10V

60R C58 S2_IP IP M_DATA7 5 R4 4


D 22uF
1 4
27MHz C30 10nF
TS_MDI7
2 3 7
M88DS3002 42
C57

C56

C52

C53

C54

C55

6V3 S2_IN IN M_DATA6 6 R3 3 TS_MDI6


16V 3V3_S2_VDDD
8 41
14

13

12

11

10

3V3_S2_VDDA VDDA_2 VDDD_3 7 R2 2 TS_MDI5


9

U3
9 40 R1
VDDA4

TEST1

TEST2

TEST3

VDDA3

XTALN

XTALP

16V GNDA_3 M_DATA5 8 1 TS_MDI4


C32 10nF 47R
F3 S2_QN 10 QN M_DATA4 39 R1584
3V3_VCC 3V3_S2_VDDA R39 C31 10nF
11 38
100nF10V

100nF10V

60R 3k3 RES VDDA2 3V3_S2_TUN S2_QP QP VCC_7 1V25_S2_VDDI


15 7
10nF 16V 47R
NC 12 37
C41

C42

16V 16 CAP CK_OUT 6 NC6 M_DATA3 5 R4 4 TS_MDI3


10pF

10pF
C27
13 36
C10

C11

CKDIV_OPT IP S2_IP 3V3_S2_VDDD VDDD_1 M_DATA2 6 R3 3 TS_MDI2


C 17 5
2 1
S11
NC
U4

3V3_S2_TUN RFBYPASS IN 1V25_S2_VDDI 14 VCC_1 M_DATA1 35


2
S5
1
18 4 S2_IN 7 R2 2 TS_MDI1
E NC 15 34 R1
E
19 RESET VDDA1 3 3V3_S2_TUN 1V25_S2_VDDI VCC_2 M_DATA0 8 1 TS_MDI0
C63 L1 M88TS2022 R1583

ADDR_SEL1

ADDR_SEL0

DISEQC_IN

CKXTAL_27
16 33
3V3_S2_VDDD

CN17 2 1
20 LNA_IN QN 2 S2_QN NC7 VCC_6 1V25_S2_VDDI
S138 4n7H

VDDD_2

DISEQC
2p2F3.3pF
2p2F

VCC_3

VCC_4

VCC_5

RESET
1

2
C62

50V

AAGC

SCLT

SDAT

VSEL
50V 50V 21 TEST QP 1 S2_QP

SDA

SCL
C20

S25

R15
4k7
VDD_DIG

VDD_REG

1nF 0.5pF
VDAA5

VDDA6

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32
R44
2

1
SDA

SCL

AGC

S2_AGC 2k
LNB_OUT 3V3_S2_VDDD
10nF
C33
22

23

24

25

26

27

28

1nF 1nF 1nF 1nF 16V RESET_S2


B

1V25_S2_VDDI

1V25_S2_VDDI

1V25_S2_VDDI
C16

C18

C17

C19

DISEQC_OUT
3V3_S2_VDDD
3V3_S2_TUN 3V3_S2_TUN

2
50V 50V 50V 50V R31 R32
00 SEÇILDI WRITE:D0H READ:D1H
2

R16
4k7
1k 1k S2_AGC
2

2
S20

10nF

10nF

KONTROL EDILECEK
C25

C26

R14
4k7
R13
4k7

16V 16V

1
10nF
C28

16V
1

R22 R38
1

1
2

F 10k SCL_S2_TUN 33R SCL_SYS 3V3_S2_VDDD F


S12

R35 R37
NC 33R SCL_S2_TUN SDA_S2_TUN 33R SDA_SYS
R36
1

18pF

18pF
C72

C73

SDA_S2_TUN
VESTEL PROJECT NAME : 17mb62-2v3
33R
50V 50V 50V 50V A3
27pF

27pF
C23

C24

A SCH NAME :TUNER&S2_TUNER&DEMOD T. SHT:


DRAWN BY :Ulas Dereli 27-10-2011_08:56
1 2 3 4 5 6 7 8 AX M

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

66
LC-22LE240

Peripherals Diagram
1 2 3 4 5 6 7 8
PC INPUT
SCART

CDA4C16GTH
4

1
D2
I

CDA4C16GTH
CDA4C16GTH
5V_VCC
SCART VIDEO OUTPUT AMPLIFIER

D1
C663

D3
1

2
2

100nF

R1479

R1311

R1310

R1265
75R

10k

10k

10k
1

R124 F179 10V

220pF
C835
2

50V
12V_VCC 220R
21

8
1k
A A

1
100nF
C120

16V
SC_CVBS_IN 15

R102
390R

R103
20

68k
R1949
50V SC_CVBS_OUT 14 100R VGA_VSNC
19 220pFC836 C860
1

R1243
2 1 Q146
2 13 100R VGA_HSNC
18 BC858B
R1233 47pF 3

220R
3
C378 12
50V
H 17
R1249 Q119
BC848B
2
SCART_CVBS_OUT
47R SC_FB 11

R1209

R1206
16 10uF

2k7

2k7
1
R1587 R620 10V
50V SC_R SC_CVBS_OUT 75R 100R 10
15 220pF

R104
33k
2 1
9

R221
100R
14
C833 R1480
75R
2 1 2
75R 1 8
13
SCART LT1

R1481 50V
75R 220pF 7
TX/SDA_SC
SC1

2 1
12 R1482 2 1

B 11 C832 SC_G 6 B
G 10
D178
2
75R
R1483
1 RX/SCL_SC
1
R1182
4k7
2
5
2 1
4
9
C15V R1187 2 1
R1419
1
22k
2

100nF SC_PIN8 3 33R VGA_B


8 50V
10V R1408
220pF SC_B C664 2 33R
7 VGA_G
2 1
C853 R1409
50V
C831 1 33R VGA_R
6 75R
2 1
3n3F F205

2 NUP4004M5

1
1
3

4
5
R1489 1 2

SC_AUD_L_IN CN711

R1516

R1515

R1517
5

75R

75R

75R
SCART_AUD_L_IN 600R

D5
4
F200

2
R1244
F 3
1 2 1
100R
2
SC_AUD_L_OUT
SCART_AUD_R_IN C854 600R
50V C857
2
C 3n3F C
1 1
F206
2
4n7F
SC_AUD_R_IN 50V
SAV RCA INPUT
F201600R R1245 47nF
1 2 1 2
SC_AUD_R_OUT 16V 30062840
100R JK4
600R R1420 C808 16V C795 R1415 62R
INDIA OPTION C858 33R K2 RIN0M CVBS0 T1
47nF
33R SC_CVBS_IN YEL 5
6
1
S9
2 SAV_CVBS_IN

C807 16V C800 R1413


30064869 47nF K3
4n7F VGA_R 16V RIN0P CVBS1 U2 33R 62R DVD_CVBS_IN 1 2 SAV_L
50V R1422 16V 1UF 4 S42
4 SC_CVBS_IN C810J2 47nF WHT
U3 3
E YEL 33R
47nF
GIN0M CVBS2
16V C806 J3 V2 16V C799 R1412 62R 2
1
S39
2 SAV_R
SCART_AUD_L_IN VGA_G GIN0P CVBS3 33R SAV_CVBS_IN RED
JK7 3 47nF 1
WHT 47nF R1421 16V 16V C794 R1411
C809H1 T3 SC_R
33R BIN0M CVBS4 33R
47nF 47nF 62R
2 SCART_AUD_R_IN 16V C802 H3
SAV Slim INPUT

1
VGA_B BIN0P

R1485

R1486
RED 1

300R
47nF SC SVHS opt

75R

75R

R11
R1423 C861 1
TP49
470R H2 SOGIN0 CVBSOUT0 T2 SCART_CVBS_OUT 1
VGA_G 50V 1nF
D TP245 D

2
1

2
L6 HSYNC0 2
VGA_HSNC SAV_CVBS_IN
DVD INTERFACE (for 26" to 32")

220pF
R1530 C959 16V

D171

C5V6

C830
L5 U1 6

50V
VGA_VSNC VSYNC0 VCOM

47nF
50V
D

2
R1652 1
TP38 3 C856
75R CN704 16V C882 L3
RIN1M 4 TP250 F203
R1650 1

!
47nF 3n3F

33R
1 2

DVD_CVBS_IN 180R 1 2 16V C798 SAV_L_IN


K1 JK3 5
SC_R 47nF
RIN1P SAV_L 600R
3 4 C973 16V C885 M3
1
TP247F202
30062423 5 7 1 2

R1624 TP44 1
1
TP5 10uF FS1 GIN1M SAV_R_IN
47nF 600R C855
DVD_SENSE
1
100R
2
5 6 16V 1 2
12V_VCC
47nF C797
U5
TP43 L2 GIN1P
1
4A/24VDC SC_G 16V SAV_R
1

NC
1

TP42 7 8 MSD9WB9PT-2
100nF

R1616

1
16V C884N3 3n3F
C628

1 2
S80
2
10V

4k7

TP242

1
TP1 BIN1M 50V
DVD_WAKEUP 47nF
TP4 9 10 DVD_IR C796
1

50V
16V 47nF
M2 BIN1P
YPbPr Slim INPUT
2

SC_B
27pF

C650

C
2
50V

R1623 220pF R1505


C862 L1
E DVD_SPDIF 100R 470R SOGIN1 R1974 TP13 E
1

SC_CVBS_IN 1nF 50V


1

C972 33R RCA_PR


M5 7
HSYNC1
N4 JK1 5
SC_FB VSYNC1
4
R1975 1
TP3
RCA_Y
16V C881 R2 3 33R
RIN2M
47nF
16V C805 6
BC848B

DVD_IR R3 RIN2P R1976 TP2


RCA_PR 1
Q157

47nF

D4 27pF 50V
33R RCA_PB
16V C883P2 2

27pF 50V
GIN2M
B R694

C829

50V 27pF

C823

C828
47nF

2
5

8
IR_IN 2
4k7
1
3V3_VCC
16V C803 1
1

P1

1
GIN2P

1
RCA_Y 1

R1619

R1620

R1621
CDA4C16GTH
47nF

75R

75R

75R
TP50
2

16V C886N1
BIN2M
47nF
2

16V C804

2
R498

N2
47k

RCA_PB BIN2P
47nF

1
F P3 F
470R SOGIN2
1

RCA_Y C859
DVD_IR_ON/OFF R1494 1nF
50V

VESTEL PROJECT NAME : 17mb62-2v3 A3


A SCH NAME :PERIPHERALs T. SHT:
DRAWN BY :<YOUR NAME HERE> 27-10-2011_09:03
1 2 3 4 5 6 7 8 AX M

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

67
LC-22LE240

RAM & NAND & CI Diagram


1 2 3 4 5 6 7 8
U5
MSD9WB9PT-2 DDR18V
3V3_VCC
F187
FLH_3.3V NAND FLASH 3V3_VCC
R1632
10k CN141 CI INTERFACE
C10 A_MADR0 60R

J1

R1

M9

J9

E1

A1

G9

G7

G3

G1

E9

C9

C7

C3

C1

A9
1 A_MADR[0] 35 1
I A_MADR[1] D21 A_MADR1 C868 C657 C656
NAND_WPz 1 NC1 NC29 48 PCM_CD1_N 36 2 PCM_D3

D205

C5V6
A9 A_MADR2 2 2
TS_MDO3 PCM_D4

VDDL

VDD5

VDD4

VDD3

VDD2

VDD1

VDDQ10

VDDQ9

VDDQ8

VDDQ7

VDDQ6

VDDQ5

VDDQ4

VDDQ3

VDDQ2

VDDQ1
A_MADR[2] 22uF 100nF 100nF 37 3
A_MADR[3] E20 A_MADR3 6V3
1

10V
1

10V 2 NC2 NC28 47 TS_MDO4 38 4 PCM_D5


A_MADR[4] B9 A_MADR4 TS_MDO5 39 5 PCM_D6
A_MADR[5] E19 A_MADR5 AA_MDATA0 DQ0 A0 AA_MADR0 3 NC3 NC27 46
FLH_3.3V R47 TS_MDO6 40 6 PCM_D7
C9 A_MADR6 G8 M8 TS_MDO7 PCM_CE_N
A A_MADR[6]
F20 A_MADR7 AA_MDATA1 AA_MADR1 4 45
3V3_VCC 4k7 41 7
PCM_A10 A
A_MADR[7] G2 DQ1 A1 M3 NC4 NC26 R48 42 8
A_MADR[8] B8 A_MADR8 FLH_3.3V R50 4k7 43 9 PCM_OE_N
A_MADR[9] F19 A_MADR9 AA_MDATA2 DQ2 A2 AA_MADR2 5 NC5 I/O7 44 PCM_A7 PCM_IORD_N PCM_A11
D20 A_MADR10 H7 M7 5 R4 4 4k7
PCM_IOWR_N
44 10
PCM_A9
A_MADR[10] 4k7 45 11

R1496
C8 A_MADR11 AA_MDATA3 AA_MADR3 6 43 PCM_A6 TSMISYNC PCM_A8

4k7
A_MADR[11] H3 DQ3 A3 N2 NC6 I/O6 6 R3 3 R49 46 12
A_MADR[12] F21 A_MADR12 TS_MDI0 47 13 PCM_A13 R1172
AA_MDATA4 DQ4 A4 AA_MADR4 F_RBZ 7 RB I/O5 42 PCM_A5 TS_MDI1 PCM_A14
A_MDATA0 H1 N8 7 R2 2 TS_MDI2
48 14
PCM_WE_N
4k7 3V3_VCC
H A_MDATA[0]
A_MDATA[1]
C13
A19 A_MDATA1 AA_MDATA5 DQ5 A5 AA_MADR5 PF_OEZ
R33
33R 8 R I/O4 41 R1 PCM_A4 TS_MDI3
49 15 R1425
33R PCM_IRQA_N
H9 N3 8 1 50 16
A_MDATA[2] A12 A_MDATA2 33R VCC_PCMCIA 51 17 VCC_PCMCIA
A_MDATA[3] B19 A_MDATA3 AA_MDATA6 DQ6 A6 AA_MADR6 NAND_CEz 9 E NC25 40 R1398 52 18
A20 A_MDATA4 F1 N7 TS_MDI4 TSMIVALID
A_MDATA[4] 53 19
A_MDATA[5] B12 A_MDATA5 AA_DDR2_DQS0 LQDS A7 AA_MADR7 10 NC7 NC24 39 C967 TS_MDI5 54 20 TSMICLK
C19 A_MDATA6 F7 P2 TS_MDI6 PCM_A12 C966 NC
A_MDATA[6] 55 21
A_MDATA[7] A13 A_MDATA7 AA_DDR2_DQSB0 LQDS_P A8 AA_MADR8 11 NC8 NC23 38 4p7F 50V TS_MDI7 56 22 PCM_A7
B14 A_MDATA8 E8 P8 TSMOCLK PCM_A6
A_MDATA[8]
C18 A_MDATA9 AA_DDR2_DQM0 AA_MADR9 R1388
12
U162 37 PCM_RST
57 23
PCM_A5 12pF
A_MDATA[9] F3 LDM A9 P3 33R FLH_3.3V VDD1 VDD2 FLH_3.3V R1171 58 24 50V
A_MDATA[10] C14 A_MDATA10 PF_AD15 8 R1 1 NAND_WPz NAND512-A 3V3_VCC 4k7 59 25 PCM_A4
A18 A_MDATA11 AA_MDATA7 AA_MADR10 PF_ALE 7 R2 2 NAND_ALE 13 36 PCM_A3
B A_MDATA[11]
A_MDATA12 F9 DQ7 A10 M2 PF_CE1Z 6
VSS1 VSS2 R1427 60 26 B
A_MDATA[12] B18 R3 3 NAND_CLE PCM_WAIT_N 33R PCM_REG_N 61 27 PCM_A2
A_MDATA[13] B13 A_MDATA13 AA_MDATA8 DQ8 A11 AA_MADR11 PF_CE0Z 5 R4 4 NAND_CEz 14 NC9 NC22 35 TSMOVALID 62 28 PCM_A1
G C8 P7

128 MEGABYTE

HY5PS121621C
A_MDATA[14] B17 A_MDATA14 TSMOSTART 63 29 PCM_A0
A_MDATA[15] C15 A_MDATA15 AA_MDATA9 DQ9 A12 AA_MADR12 15 NC10 NC21 34 TS_MDO0 64 30 PCM_D0
C2 R2 TS_MDO1 PCM_D1
65 31
A16 A_DDR2_DQS0 AA_MDATA10 AA_BADR_BA0 NAND_CLE 16 33 TS_MDO2 PCM_D2

U155
A_DQS[0] D7 DQ10 BA0 L2 CL NC20 66 32
A_DQSB[0] C16 A_DDR2_DQSB0 PCM_CD2_N 67 33 4k7 VCC_PCMCIA
A_DQS[1] A15 A_DDR2_DQS1 AA_MDATA11 DQ11 BA1 AA_BADR_BA1 NAND_ALE 17 AL I/O3 32 PCM_A3
B15 A_DDR2_DQSB1 D3 L3 5 R4 4 R1642 68 34 R1177
A_DQSB[1] R34 3V3_VCC 10k

BSH103
AA_MDATA12 DQ12 RAS_P AA_RASZ PF_WEZ 33R 18 W I/O2 31 PCM_A2
6 R3 3

Q209
D1 K7
A_DQM[0] B16 A_DDR2_DQM0 R1495
A_DQM[1] C17 A_DDR2_DQM1 AA_MDATA13
D9 DQ13 CAS_P L7
AA_CASZ FLH_3.3V 3k9 19 WP I/O1 30
7 R2 2
PCM_A1
5V_VCC VCC_PCMCIA
A_MCLK C12 A_MCLK AA_MDATA14 DQ14 WE_P AA_WEZ NAND_WPz 20 NC11 I/O0 29 R1 PCM_A0 C970
B1 K3 8 1 C654 C653
A_MCLKZ B11 A_MCLKZ 33R
2 2

22uF
100nF 100nF
A_MCLKE AA_MDATA15
F A_MCLKE C20 21 28 R1389 1 1

DQ15 CS_P NC12 NC19 10V 10V 6V3


B9 L8

2
10V
100nF
C1220
A_WEZ B20 A_WEZ AA_DDR2_DQS1 UDQS CKE AA_MCLKE 22 NC13 NC18 27
B10 A_RASZ B7 K2
C A_RASZ
A10 A_CASZ AA_DDR2_DQSB1 AA_MCLK 23 26 C
A_CASZ A8 UDQS_P CK J8 NC14 NC17 R1951 R1950
A_BADR[0] C21 A_BADR_BA0 12V_VCC 4k7 10k
A_BADR[1] B21 A_BADR_BA1 AA_DDR2_DQM1 UDM CK_P AA_MCLKZ 24 NC15 NC16 25
D19 A_BADR_BA2 B3 K8
A_BADR[2]
A_ODT C11 A_ODT
A2 NC1 ODT AA_ODT
K9 R1953
3
TS IN& OUT
P_D0 K21 PCMDATA[0]/CI_DATA[0] TS1DATA[0] P18 TS1_D0 CI_POWER_CTRL 4k7
2
Q208
MVREF F18 MVREF NC2 VSS1 P_D1 L19 PCMDATA[1]/CI_DATA[1] TS1DATA[1] R18 TS1_D1 BC848B TS1_D0 R4 TS_MDI0
E2 A3 P_D2 M19 T18 TS1_D2 1 TS1_D1 5 R3 4 TS_MDI1
PCMDATA[2]/CI_DATA[2] TS1DATA[2]
AA_BADR_BA2 NC3 VSS2 P_D3 T12 PCMDATA[3]/CI_DATA[3] TS1DATA[3] W19 TS1_D3 TS1_D2 6 R2 3 TS_MDI2
L1 E3 P_D4 U13 Y21 TS1_D4 TS1_D3 7 R1 2 TS_MDI3
PCMDATA[4]/CI_DATA[4] TS1DATA[4]
E R1367 R3 NC4 VSS3 J3
P_D5 V14 PCMDATA[5]/CI_DATA[5] TS1DATA[5] Y19 TS1_D5 8
33R
1
A_MDATA14 1 R1 8 AA_MDATA14 P_IOWR_N R4 4 PCM_IOWR_N P_D6 V12 PCMDATA[6]/CI_DATA[6] TS1DATA[6] R21 TS1_D6 R1383
A_MDATA9 2 AA_MDATA9 P_IORD_N5 PCM_IORD_N P_D7 TS1_D7 TS1_D4 TS_MDI4
R2 7 R7 NC5 VSS4 N1 R3 3 V18 PCMDATA[7]/CI_DATA[7] TS1DATA[7] T21 R4
A_MDATA12 3 R3 6 AA_MDATA12 P_A13 6 R2 2 PCM_A13 TS1CLK Y20 TS1_CLK TS1_D5 5 R3 4 TS_MDI5
A_MDATA11 4 R4 5 AA_MDATA11 NC6 VSS5 P_WE_N 7 PCM_WE_N P_A0 R19 W20 TS1_VALID TS1_D6 6 R2 3 TS_MDI6
R8 P9 8 R1 1 P_A1 P19
PCMADR[0]/CI_A[0] TS1VALID
R16 TS1_SYNC TS1_D7 7 R1 2 TS_MDI7
VSSQ10

22R 33R PCMADR[1]/CI_A[1] TS1SYNC C969 8 1


VSSDL

VSSQ9

VSSQ8

VSSQ7

VSSQ6

VSSQ5

VSSQ4

VSSQ3

VSSQ2

VSSQ1

R1385 P_A2 N21


VREF

R1369 PCMADR[2]/CI_A[2] 12pF 33R


A_MDATA5 1 R1 8 AA_MDATA5 P_WAIT_N PCM_WAIT_N P_A3 N19 50V NC R1382
A_MDATA2 2 R2 7 AA_MDATA2 P_CE_N 5 R4 4 PCM_CE_N P_A4 V20
PCMADR[3]/CI_A[3]
D A_MDATA0 3 R3 6 AA_MDATA0 P_OE_N 6 R3 3 PCM_OE_N P_A5 U20
PCMADR[4]/CI_A[4]
TS1_CLK
R1512
TSMICLK D
J2

J7

H8

H2

F8

F2

E7

D8

D2

B8

B2

A7

A_MDATA7 4 R4 5 AA_MDATA7 P_IRQA_N 7 R2 2 PCM_IRQA_N P_A6 T20


PCMADR[5]/CI_A[5] 33R
DDR18V 1k 8 R1 1 P_A7 T19
PCMADR[6]/CI_A[6]
K20 TS0_D0
R1514
TS1_VALID 33R TSMIVALID
22R R1364 33R PCMADR[7]/CI_A[7] TS0DATA[0]
R1610 R1399 P_A8 P17 PCMADR[8]/CI_A[8] TS0DATA[1] L20 TS0_D1 R1513
D A_MDATA6
A_MDATA1
1 R1 8 AA_MDATA6
AA_MDATA1
P_A9 N18
P_A10 U17
PCMADR[9]/CI_A[9] TS0DATA[2] M20 TS0_D2
TS0_D3
TS1_SYNC 33R TSMISYNC
2 R2 7 C687 PCMADR[10]/CI_A[10] TS0DATA[3] T13
R1355

A_MDATA3 3 R3 6 AA_MDATA3 P_A11 V16 U14 TS0_D4


1k

220nF PCMADR[11]/CI_A[11] TS0DATA[4]


A_MDATA4 4 R4 5 AA_MDATA4 10V DDR18V P_A12 R20 PCMADR[12]/CI_A[12] TS0DATA[5] U12 TS0_D5 TS0_D2 R4 TS_MDO2
22R C718 C715 C714 C716 C711 C713 C1214 R1393 P_A13 R17 PCMADR[13]/CI_A[13] TS0DATA[6] T11 TS0_D6 TS0_D1 4 R3 5 TS_MDO1
R1366 220nF 220nF 220nF 220nF 220nF 220nF 220nF 33R P_A14 T16 PCMADR[14]/CI_A[14] TS0DATA[7] U18 TS0_D7 TS0_D0 3 R2 6 TS_MDO0
A_MDATA13 AA_MDATA13 2 7
1 R1 8 10V 10V 10V 10V 10V 10V 10VP_D1 5 R4 4
PCM_D1 P_RESET V19 CI_RST TS0CLK U19 TS0_CLK TS0_D3 R1 1 8
TS_MDO3
A_MDATA10 2 R2 7 AA_MDATA10 P_D0 PCM_D0 P20 TS0_VALID C968
A_MDATA8 3 R3 6 AA_MDATA8 P_D2 6 R3 3 PCM_D2 P_IRQA_N W21
TS0VALID
K19 TS0_SYNC 12pF
33R
R1384
A_MDATA15 4 R4 5 AA_MDATA15 P_A0 7 R2 2 PCM_A0 P_OE_N
PCM_IRQ/CI_INT TS0SYNC
TS0_D4 TS_MDO4
F181 U16 50V 30022165 KULLANILDI
8 R1 1 P_IORD_N V17
PCMOEN
2
R4
TS0_D5 5 R3 4 TS_MDO5
22R 1V8_VCC DDR18V PCMIOR/CI_RD
P_D5 PCM_D5 P_CE_N TS0_D6 6 R2 3 TS_MDO6
A_MADR11
R1609
1 R1 8 AA_MADR11 A_ODT
R1603
AA_ODT
60R
2
C712 2
C709 2
C710 C782
P_D6 5 R4 4
PCM_D6 P_WE_N
T17
V21
PCMCEN/CI_CS U5 10V
TS0_D7 7 2 TS_MDO7
22R 100nF 100nF 100nF 22uF R3 3 PCMWEN 100nF R1
A_MADR8 2 R2 7 AA_MADR8 P_D7 6 PCM_D7 PCM_CD2_NT14 MSD9WB9PT-2 C906 8 1
C
1 1 1

10V 10V 10V 6V3 R2 2 CI_CD R6 33R


A_MADR6 3 R3 6 AA_MADR6 P_A6 7 PCM_A6 P_WAIT_N M21 R1390
E A_MADR4 4 R4 5 AA_MADR4 A_WEZ
R1613
1 R1 8 AA_WEZ 8 R1 1
P_IOWR_N P16
PCMWAIT/CI_WACK
W1
100R DIGITAL_IF_P E
33R 3V3_VCC PCMIOW/CI_WR IP R1402

R1977
180R
A_MCLKE 2 R2 7 AA_MCLKE P_REG_N N20 TS0_VALID TSMOVALID
2
22R R1397 R1660 PCMREG/CI_CLK IM Y1 33R
A_BADR_BA1 3 R3 6 AA_BADR_BA1 AVDD_DDR 1k P_A1 R4 4 PCM_A1 4k7 R1401
A_BADR_BA0 4 R4 5 AA_BADR_BA0 P_D3 5 PCM_D3 TS0_SYNC TSMOSTART
R1365 R3 3 100R DIGITAL_IF_N 33R
MVREF P_D4 6 PCM_D4 OVER_CUR_DETECT G21 GPIO125
22R R2 2 R5 C905 R1424
1

P_A4 7 PCM_A4 TS0_CLK TSMOCLK

3V3_VCC
R1 1 18kR1607 G20 GPIO128 100nF 33R
8 HDMI0_5V
R1332 C683 33R 18k G19 GPIO127
HDMI1_5V 330R 10V
R1356

A_DDR2_DQM1 AA_DDR2_DQM1 R1395 VIFP AA2 3V3_TUNER


1k

R1380 22R 220nF R1606


A_BADR_BA2 1 R1 8 AA_BADR_BA2 R1313 10V P_A2 R4 PCM_A2 VIFM Y2
2

F8
1
R1605

R1604

100nF
P_REG_N 5 R3 4

C913
A_MADR1 2 R2 7 AA_MADR1 A_DDR2_DQM0 AA_DDR2_DQM0 PCM_REG_N
33k

33k

16V
22R 6 3
A_MADR10 3 R3 6 AA_MADR10 P_A3 PCM_A3 SIFP Y3 1k

R12
4k7
R2

R1662
A_MADR5 4 R4 5 AA_MADR5 P_RESET 7 R1 2 PCM_RST SIFM AA3

1k2
B 22R
A_MCLKZ R1982
AA_MCLKZ
8
33R
1
PF_ALE U10
IF_AGC_MST
S81 R344
R1370 22R R1392 PF_ALE/GPIO135 IF_AGC W5 4k7 9k1 1k2 BACKLIGHT_ON/OFF
A_MADR3 1 R1 8 AA_MADR3 A_MCLK 22R AA_MCLK P_A14 R4 PCM_A14 PF_AD15 T9 PF_AD[15]/GPIO130 RF_AGC W4 4k7 R1971 NC
A_MADR9 2 R2 7 AA_MADR9 R1983 P_A10 5 R3 4 PCM_A10 PF_CE0Z V11 PF_CE0Z/GPIO131 R10 0R R1661
3

A_MADR7 3 R3 6 AA_MADR7 P_A9 6 R2 3 PCM_A9 PF_CE1Z U11 PF_CE1Z/GPIO132 GPIO66 AA4 4k7
1 2 2
Q181
A_MADR12 4 R4 5 AA_MADR12 P_A5 7 R1 2 PCM_A5 PF_OEZ U9 PF_OEZ/GPIO133 GPIO67 Y4 PANEL_VCC_ON/OFF
BC848B
8 1 PF_WEZ T10
F GPIO68 W6 TUN_SCL_MST F
1
22R R1984 33R PF_WEZ/GPIO134
R1368 A_DDR2_DQSB1 22R AA_DDR2_DQSB1 R1394 F_RBZ 33R V9 F_RBZ/GPIO136 GPIO69 Y5 TUN_SDA_MST
A_MADR2 1 R1 8 AA_MADR2 A_DDR2_DQS1 22R AA_DDR2_DQS1 P_A7 PCM_A7
A_MADR0 2 R2 7 AA_MADR0 P_A8 5 R4 4 PCM_A8
R1942

1
R1985 R3

R1618

R1663
A_CASZ 3 R3 6 AA_CASZ P_A11 6 R2 3 PCM_A11

4k7

4k7

4k7

4k7
R8

R9
A_RASZ 4 R4 5
22R
AA_RASZ
A_DDR2_DQSB0
R1987
22R AA_DDR2_DQSB0
P_A12 7
8 R1 1
33R
2 PCM_A12
VESTEL PROJECT NAME : 17mb62-2v3 A3

2
A_DDR2_DQS0 AA_DDR2_DQS0
A 22R
R1986
R1396 3V3_VCC SCH NAME :RAM&NAND&CI T. SHT:
DRAWN BY :<YOUR NAME HERE> 27-10-2011_09:04
1 2 3 4 5 6 7 8 AX M

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

68
LC-22LE240

Audio IO & HDMI Inputs Diagram


1 2 3 4 5 6 7 8

I
HDMI2 CN708
21
R1877 20
AUDIO OUTPUTs HDMI_0_RX2P 2
10R
1

R1869
1
2
R1900 HDMI_0_RX2N 2
10R
1
3

OPTIONAL
MAIN_L 100R DSP_MAIN_L C1197 HDMI_0_RX1P 10R 4

HDMI1_5V
2
1

SCART_AUDIO_IN_L C1198 10uF 10V N5 AUL0 RXA0N E2 HDMI_1_RX0N R1868 R1887 5


L4 F3
A SCART_AUDIO_IN_R 10uF 10V AUR0 RXA0P HDMI_1_RX0P HDMI_0_RX1N 2
10R
1
6 A

R1899

C1183
220k

4n7F
10uF 10V R5 F2

50V
SAV_AUDIO_IN_L AUL1 RXA1N HDMI_1_RX1N HDMI_0_RX0P 1 10R 2 7
SAV_AUDIO_IN_R 10uF 10V C1196 T6 AUR1 RXA1P G3 HDMI_1_RX1P R1867 R1886 8
C1195 P6 AUL2 RXA2N G2 HDMI_1_RX2N HDMI_0_RX0N 2 1
9
R1909 10R
R1897 P5 AUR2 RXA2P G1 HDMI_1_RX2P 2 1
HDMI_0_CLKP 10R 10
1k 2
1

T4 E3

2
MAIN_R 100R DSP_MAIN_R AUL3 RXACKN HDMI_1_CLKN R1879 R1880 11

R1896
T5 E1

4k7
AUR3 RXACKP HDMI_1_CLKP HDMI1_HPD HDMI_0_CLKN 2
10R
1
12

C1184
H

4n7F
H5

50V
R1898 DDCDA_CK HDMI_1_SCL CEC 13
220k
3

DSP_MAIN_L N6 AUOUTL0 DDCDA_DA H6 HDMI_1_SDA 14

1
R1912 R1888
DSP_MAIN_R R6 AUOUTR0 HOTPLUGA J6 2 1 2
Q204 2 1
15
1k HDMI_0_SCL 10R
DSP_SCART_L W9 AUOUTL1 BC848B 10R 16
HDMI_0_SDA

HDMI0_5V
2
1

DSP_SCART_R AA9 AUOUTR1 RXB0N B2 HDMI_0_RX0N


1
R1885 17
DSP_HP_L Y7 EAR_OUTL RXB0P B1 HDMI_0_RX0P 18
HDMI0_5V
C1168 L119 DSP_HP_R AA7 EAR_OUTR RXB1N C2 HDMI_0_RX1N 10R 19
HDMI0_HPD 2 1

2 1
RXB1P C1 HDMI_0_RX1P R1878
HP_L DSP_HP_L
4u7H U5 D2

2
RXB2N HDMI_0_RX2N R1910

R1864

R1865
100uF D1

47k

47k
MSD9WB9PT-2 RXB2P HDMI_0_RX2P 2
1k
1
R1858

16V
220R

U5 A2

2
AUVRP RXBCKN HDMI_0_CLKN

R1895
U6 3 C3

4k7
16V 10V 1uF AUVAG RXBCKP HDMI_0_CLKP HDMI0_HPD

1
U4 J5
B C1170 100nF
C117410uFC1199 C1201 C1200 AUVRM DDCDB_CK
K4
HDMI_0_SCL
HDMI_0_SDA
3 B
G 10uF 6V3 4u7F DDCDB_DA

1
R1911
K5 CN707
HDMI1
10V 10V HOTPLUGB 2
1k
1 2
Q203
BC848B 21
RESET_TUNER MODE SELECTION D4 I2S_OUT_MCK
1
20
R1874
C1169 L120 DVD_IR_ON/OFF MODE SELECTION D6 I2S_OUT_SD HDMI_1_RX2P 1
1
10R
2 1
ANT_CTRL F4 I2S_OUT_WS 2
HP_R DSP_HP_R R1917 R76 R1870
4u7H STBY_INFO MODE SELECTION F5 I2S_OUT_BCK CEC H4 2 1 2 1
12V_VCC HDMI_1_RX2N 2 1
3
100uF 10R 1k 10R
3 HDMI_1_RX1P 10R 4
R1859

16V
220R

E4 I2S_IN_BCK U9 VCC R1884 R1871 5


AMP_MUTE LM809 RST GND
C4 I2S_IN_SD C1 HDMI_1_RX1N 2 1
6
PROTECT 10R
D3 2 1

1
RESET_S2 I2S_IN_WS HDMI_1_RX0P 10R 7

COMMON
2

R74
10R

6V3
1uF

R75
10R
C1171 R1872 R1882 8
10uF HDMI_1_RX0N 2
10R
1
9
NC

1
10V HDMI_1_CLKP 10R 10

2
R1601

R1838

R1839

R1840

R1892

R1836

R1656

R1614
1

F P4

4k7

10k

10k

10k

4k7
R17
4k7

10k

4k7

4k7
SPDIFO R1876 R1883 11
R223 HDMI_1_CLKN 2
10R
1
12

3V3_STBY
SC_L_OUT CEC 13
1

2
2 1
100R DSP_SCART_L
2

SPDIF_OUT R1873 14
R1924

C1185

100pF
22k

50V

C HDMI_1_SCL
2
10R
1
15 C
3V3_STBY

3V3_STBY

3V3_VCC

3V3_VCC

3V3_STBY

3V3_STBY
HDMI_1_SDA 2 10R 1 16
R1875 17
1

R222 HDMI1_5V 18
SC_R_OUT
2
100R
1
DSP_SCART_R HDMI1_HPD 2
10R 1 19
2

PRE-AMP for SCART AUDIO R1881


R1925

C1186

100pF

2
22k

50V

R1863

R1862
47k

47k
1

R1916

1
E V+ 220k 12V_VCC
C1182

R1915
220k
10uF
10V

C1177 F301
2 1

12V_VCC

AUDIO INPUTs
C1181 600R
D SC_AUD_R_OUT
100nF D
16V R1913
C1206 R1914
1
33k
2 C1180
10uF PL1
10V
2
33k
1
SC_AUD_L_OUT
D SC_AUD_R_IN
R1902 47pF
C1205
10uF
10k SCART_AUDIO_IN_R 50V 10V
R1927 47pF PL2
1 2 1 OUT1 VDD 8
82k
R1921

C1187

470pF

50V
12k

50V

C1203 R1929 U178 R1926


1 2 2 IN1- OUT2 7 1 2
SC_R_OUT 20k 82k
TL062 R1928 C1202
1uF PL3
V+ 3 IN1+ IN2- 6 1 2

6V3 20k SC_L_OUT


4 VSS 1uF
R1901 IN2+ 5 V+ 6V3
SC_AUD_L_IN 10k SCART_AUDIO_IN_L PL4
R1920

C1188

470pF
12k

50V

C
E E
COAX SPDIF OUT
R1903
SAV_R_IN 10k SAV_AUDIO_IN_R F5
2 1

5V_VCC
600R
R1918

C1189

470pF

100nF
2
12k

50V

C15

16V
R1889
4k7

50V
3
220pF NC C1175
1

R1907
TP251

Q202
B SPDIF_OUT
1 2 2 1 2
1 2 100R
R1904 BC848B
220pF

C1178

C1179 100nF
2

1
50V

SAV_L_IN 10k SAV_AUDIO_IN_L


1
R1890

10V
4k7

C1176
2
1

2 NC
R1919

C1190

470pF

1 2 1 2
3 S92
12k

50V

JK10 100nF
1
2
2

R1908

10V
C5V6

D199

F F
1k

NC
1

VESTEL PROJECT NAME : 17mb62-2v3 A3


A SCH NAME :AUDIO_IO&HDMI_INPUTs T. SHT:8
DRAWN BY :<YOUR NAME HERE> 27-10-2011_09:04
1 2 3 4 5 6 7 8 AX M

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

69
LC-22LE240

Audio AMP & HP AMP Diagram


1 2 3 4 5 6 7 8

I
AUDIO AMP for 16" to 24" POP NOISE CIRCUIT
VDD_AUDIO
S87 NC
12V_VCC 1 2

A U163 PT2333
5V_VCC 1
S86 2
A

GNDA

OUTN

VDDA

VDD1

GNDB

OUTP
INP

INN

SDB

1
1N4148

D191
MAIN_L Q160

R1941
BC848B

VDD_AUDIO

3V3_STBY

3V3_VCC
16V

A1

A2

A3

B1

B2

B3

C1

C2

C3

1k
10uF

2
C612 R623
H 4k7
220nF L_AUDIO_P_OUT C1032

AMP_EN

R1699
10V
R817
100R

47k
C665 2

L_AUDIO_N_OUT 100nF
NC NC

2
1

10V

R1712

R1309
R616
15k

10k

10k
R624
1

4k7
Q195

1
BC858B 2

VDD_AUDIO AMP_EN BC848B

2
NC C1058 Q186
3

220nF

R1711

R1701
C617

100k
3

10V

3k9
100nF R1702
B 16V 2 2
10k
1

B
VDD_AUDIO

1
3

2
1

R1684

R1718
100k
AMP_MUTE 1 2 2
BC848B
10k Q185
1

1
U164 PT2333
GNDA

OUTN

VDDA

VDD1

GNDB

OUTP
INP

INN

SDB

2
BC848B
MAIN_R Q133
A1

A2

A3

B1

B2

B3

C1

C2

C3

1
C602 R613
4k7
220nF R_AUDIO_P_OUT
F
AMP_EN

10V
C666
R818
100R

R614
4k7

R_AUDIO_N_OUT 10V
1

100nF
C C
220nF

C608
10V

VDD_AUDIO

CN710 30001734 KULLANILDI


1 F283
E 12V_VCC
R_AUDIO_P 2 60R
F285NC D19230049510 KULLANILDI
R_AUDIO_N 3 VDD_AUDIO_PWR
60R SK24
L_AUDIO_P 4 F294
5V_VCC VDD_AUDIO
L_AUDIO_N 5 60R
10V 10V
D 6 220uF
C870
220uF D
C615

D Ü.A. DEGISTIRILECEK

AUDIO AMP for 26" to 32" L124

10uH SLIM HEADPHONE OUTPUT


AMP_EN

F282 F296
VDD_AUDIO 1
L_AUDIO_P
60R L_AUDIO_P_OUT 60R TP230 1
TP51 1
C1121

10uF

C942
2
16V

1nF
50V
HP_L
C1226

1 SD PVCCL2 28
6
1uF
25V

30022132 KULLANILDI S85 2 27


FAULT PVCCL1 TP229
C
1

100k 30050557 KULLANILDI


C1077 C1045 3
1uF 220nF HP_R
3 26 L125
E R1715 MAIN_L 6V3
LINP BSPL
25V C1172 C729
4 E

2
30050557 KULLANILDI
VDD_AUDIO 100k 10nF 10nF

R1854

R1855
C10751uF 4 25 10uH

10k

10k
R1714 LINN OUTPL 16V 16V
NC 6V3 5 JK6
CONNECT TO DSP_M_L GND F299
NC100k 5 GAIN0 PGND1 24 L_AUDIO_N_OUT

1
L_AUDIO_N
R1717 60R 7
C943

6 23
1nF
50V

VDD_AUDIO 10k C1123 GAIN1 OUTNL R1704


C1227

R1716 100R U168 C1046


2N7002
680R HP_MUTE 1 TP52
1 8 7 22
1uF
25V

ANALOG VCC AVCC BSNL 25V


R1 1uF Q192
50V TPA3110D2 220nF R_AUDIO_N_OUT F298 HP_DETECT 4k7 1 3V3_VCC
2 R2 7 8 AGND BSNR 21 C1044 R1149
25V R_AUDIO_N
VDD_AUDIO C1074 220nF 60R
C944

D203

C5V6
3 R3 6 1uF 9 20
1nF
50V

B GVDD OUTNR L126 3V6 lik zener kullanilmali


C1228

25V
R1687 R1696
4 R4 5 10 19 10uH
1uF
25V

10k 10k PLIMIT PGND2


R1741 30050557 KULLANILDI R_AUDIO_P_OUT R1960
C1073 C10761uF11 RINN OUTPR 18 680R
1uF L127 2N7002
6V3 Q210
25V 30050557 KULLANILDI
12 17 C1043220nF
RINP BSPR
25V 10uH
F 6V3
13 16 F
MAIN_R 1uF NC PVCCR1 F297
C1078 F281 R_AUDIO_P
14 PBTL PVCCR2 15 VDD_AUDIO 60R
CONNECT TO DSP_M_R GND
C945

VESTEL PROJECT NAME : 17mb62-2v3


1nF
50V

60R
C1122

C1229

A3
10uF
16V

1uF
25V

A SCH NAME :AUDIO_AMP&HP_AMP T. SHT:8


DRAWN BY :<YOUR NAME HERE> 27-10-2011_09:04
1 2 3 4 5 6 7 8 AX M

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

70
LC-22LE240

GPIOS & USB & LVDS_OUT Diagram


1 2 3 4 5 6 7 8
10k
R1835
I 10k
R1833 TX_B_0_N 30
PCM_CD1_N
J21 AA19 TX_B_0_P
15.6" LVDS OPTION TP34
TX_B_0_P
1

TP14
R1615 PWM0 LVB0P 29
3V3_VCC
BACKLIGHT_DIM
2
4k7
1 J20
J19
PWM1
PWM2
LVB0M
LVB1P
AA20
AA18
TX_B_0_N
TX_B_1_P 3V3_STBY
SERIAL FLASH D165
CN3 TP33
TX_B_1_N
1

28
W18
A 3V3_STBY LVB1M TX_B_1_N 3V3_STBY TX_A_0_N 1 2 PANEL_VCC TP32 A

1
1

W17

2
TX_B_2_P TX_B_1_P

TP15
TP40
TP11
LVB2P C658 1N5819 27

R1528

R1357

R1358
Y18

4k7

4k7
4k7
2

LVB2M TX_B_2_N 100nF TX_A_0_P 3 4 TP31

R1183
1

W16 U158

4k7
1

LVBCKP TX_B_CLK_P 10V TX_B_2_N 26


KEYBOARD B4 Y17 TX_B_CLK_N MX25L512

TP12
SAR0 LVBCKM 5 6 TP30
1
R1967

1
1

DVD_SENSE C5 SAR1 LVB3P AA16 TX_B_3_P SPI_CSN_1 1 2 1 CS# VCC 8 TX_B_2_P 25


100R

19" TO 22" DOUBLE LVDS FFC OPTIONS


V3 SAR2 LVB3M Y16 TX_B_3_N SPI_SDO 2 7 TX_A_1_N
100RR1968 SO HOLD# 7 8 TP29
1 2
SC_PIN8 R1248 1

AA15 3 6
H R1 LVB4P TX_B_4_P WP# SCLK 24
1 2 1 2
FLASH_WPN 100R R1970100R SPI_SCK

1
3V3_STBY 4k7 LVB4M W15 TX_B_4_N R1969 4 GND SI 5 1 2
TX_A_1_P 9 10
100R SPI_SDI_1

1
2 1

NC TX_B_CLK_N 23
DVD_WAKEUP B6 W14 TX_A_0_P DIMMING

TP41
GPIO12 LVA0P 11 12 TP28 1

C7 SCZ LVA0M Y15 TX_A_0_N R73 TX_B_CLK_P 22


SPI_CSN_1
B5 SCK LVA1P W13 TX_A_1_P TX_A_2_N 13 14 33k TP27
SPI_SCK PANEL_VCC 1

C6 SDI LVA1M Y14 TX_A_1_N R2 TX_B_3_N 21


SPI_SDI_1
A6 SDO LVA2P AA13 TX_A_2_P TX_A_2_P 15 16 33k BACKLIGHT_ON/OFF TP26
SPI_SDO 1

A7 GPIO14 LVA2M Y13 TX_A_2_N TX_B_3_P 20


FLASH_WPN
LVACKP AA12 TX_A_CLK_P TX_A_CLK_N 17 18 12V_VCC TP25 1

LVACKM W12 TX_A_CLK_N TX_A_0_N 19


3V3_VCC LVA3P W11 TX_A_3_P TX_A_CLK_P 19 20 TP24 1

K6 Y12
B RX/SCL_SC
M6
DDCA_CK/UART0_RX LVA3M TX_A_3_N KEYBOARD_ONBOARD C630 TX_A_0_P 18 B
1

TX/SDA_SC DDCA_DA/UART0_TX LVA4P W10 TX_A_4_P


2

TP23
100nF
R1524

R1527

G Y11
4k7

4k7

LVA4M TX_A_4_N R793 F248 10V 17


U5 1
47R
2 1 2

KEYBOARD
MSD9WB9PT-2 R1959 TOUCH_PAD_OPTION F249 600R TX_A_1_N 16
2

H19 S76
SCL_SYS DDCR_CK 4 1
4k7
2
3V3_STBY 1 2
3V3_STBY TP22 1

SDA_SYS H20 DDCR_DA GPIO137 Y9 600R TX_A_1_P 15


HP_MUTE
SPDIFI/GPIO139 W7 TP21
DVD_SPDIF R1937 1

GPIO141 AA10 100R HP_DETECT MECH_SWITCH 1 2


14
47R SCL_SYS
C952
33pF

Y10
50V

R1543 GPIO143 R1954 CI_POWER_CTRL R1936


IR_IN 1 2 A4 IRIN R1952 1 2
TX_A_2_N 13
100R 47R SDA_SYS
1
4k7 2
3V3_VCC TP20

CN709
1

TX_A_2_P 12

6
TP19
R1533

Y6 B7 STBY_ON/OFF_NOT TX_A_CLK_N
1M

XIN GPIO10 11
24MHz

AA6 E6
EXT KEYPAD
X2

XOUT GPIO11 TP18


F LED1 1

GPIO7 F6 TX_A_CLK_P 10
S38 LED2
TP17 1
1

TX_A_3_N 9
R1617

R1672

R1671
C951
33pF

E5
50V

4k7

4k7

4k7

C RESET 100R HWRESET TP16 C


SINGLE LVDS FFC OPTIONS
2 1 1

R1666 TX_A_3_P 8
C1215

10nF
16V

TP9
2

7
B3
3V3_STBY

3V3_STBY

3V3_STBY

USB0_DP S15

PANEL_VCC = 5V/12V
PANEL_VCC
A3 USB0_DM
2 1
6

OP_PIN11

TX_A_CLK_P

TX_A_CLK_N

OP_PIN27

OP_PIN42

OP_PIN43
OP_PIN8

OP_PIN9
W8 USB1_DP
USB_DP

TX_A_3_P

TX_A_3_N

TX_A_2_P

TX_A_2_N

TX_A_1_P

TX_A_1_N

TX_A_0_P

TX_A_0_N
Y8 USB1_DM 5
USB_DM
J9

2
GND0
H9

S14

S13
OP_PIN9

S3
GND1 4
E PANEL_VCC 3

PANEL_VCC
ONBOARD KEYBOARD 1

LED SOCKET TP8 2

CN138
TP10

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30
1
CN703

9
1
1

1
TP56 CN139
D204

B5V1

KEYBOARD_ONBOARD

TP57 5V_STBY
D TP54 1
1
F259 D
470R
R23

R45
10k

CN137
2k
R7

1 2
TP53 IR_IN
R1940

1
150R

C949 600R

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30
1

9
TP55
1 2
+ -
D 27pF
1

Q170 50V
BC848B
4

3
2

2
SW5
R1563

R1571

R1562
220R

2
10k

10k

2
R1572

E2 E1
220R

1
Q171
R1567
10k

1
BC848B R71 R68
1

R1568
10k

PANEL_VCC OP_PIN5 PANEL_VCC OP_PIN10


G4

G3

G2

G1

33k 33k
1

3 3

Q174 R60 R57


2 2 1 2 1 2
10k 10k
Q173
BC858B BC858B 3 BUTTONS KEYBOARD OPTION
LED2

1 1
R70 R66
LED1

PANEL_VCC 33k OP_PIN6 PANEL_VCC 33k OP_PIN11


OP_PIN43
OP_PIN42

OP_PIN27

OP_PIN11
OP_PIN10
OP_PIN9
OP_PIN8
OP_PIN7
OP_PIN6
OP_PIN5
2

C R59 R55

TX_B_CLK_P
TX_B_CLK_N

TX_A_CLK_P
TX_A_CLK_N
R1569

R1570
220R

220R

PANEL_VCC

E 1
10k
2 1
10k
2

E
TX_B_4_P
TX_B_4_N
TX_B_3_P
TX_B_3_N

TX_B_2_P
TX_B_2_N
TX_B_1_P
TX_B_1_N
TX_B_0_P
TX_B_0_N

TX_A_4_P
TX_A_4_N
TX_A_3_P
TX_A_3_N

TX_A_2_P
TX_A_2_N
TX_A_1_P
TX_A_1_N
TX_A_0_P
TX_A_0_N
R69 R65
1

5V_STBY PANEL_VCC 33k OP_PIN7 PANEL_VCC 33k OP_PIN27

PANEL VCC = 5V/12V USB INTERFACE 1


R58
10k
2 1
R54
10k
2
TP6

R62

RESET R844 S4 PANEL_VCC 33k OP_PIN42


1

4 6 IO4 IO1 1 1 2
MEGA_DCR_IN
10R USB_DP R51

CN2
U145
USB

51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
R1668 R67 1
10k
2

9
8
7
6
5
4
3
2
1
3V3_STBY 1k 3 5 VDD GND 2 PANEL_VCC 33k OP_PIN8
AZ099-04S R845 R56 R63
OP_PIN45

OP_PIN43
OP_PIN42
C1016

100nF

B LG BASED 30070519
TP59 TP60
1

TP35
1

4 IO3 IO2 3
16V

PANEL_VCC OP_PIN43
TP61

2 1
10R
2
USB_DM
1
10k
2
33k
R52
C1031

22uF
6V3

1 PANEL_VCC S2 1
10k
2
1

C610 MEGA_DCR_OUT
1

TP58
1

RESET CN1 10uF 1


TP7 R72 R64
10V PANEL_VCC 33k OP_PIN9 PANEL_VCC 33k OP_PIN45
F F
1N4148

R61 R53
R1667

C1015
D189

CN4
10k

2
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1 2 1 2
100nF 10k 10k

9
8
7
6
5
4
3
2
1
1

10V 5V_VCC 1 VIN 5


VOUT
U8
2 GND SAM BASED 30070519

3V3_VCC 4k7
FPF2124
3 ON ISET 4
R46
560R
VESTEL PROJECT NAME : 17mb62-2v3 A3
SCH NAME :GPIOs&USB&LVDS_OUT T. SHT:
A R1198

DRAWN BY :<YOUR NAME HERE> 27-10-2011_09:04


1 2 3 4 5 6 7 8 AX M

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

71
LC-22LE240

POWER_1 & LNBP Diagram


1 2 3 4 5 6 7 8
F274
F277
I 1V2_VCC VDDC_1V2
2V5_VCC
60R
AVDD_2V5_PGA
60R C1007
C1081 C997 C1005 C1070

D10
E10
F10
G10
H10
J10
K10
L10
M10
N10
P10
R10
D11
E11
F11
G11
H11
J11
K11
L11
M11
N11
P11
R11
D12
E12
F12
G12
H12
J12
K12
L12
M12
N12
P12
R12
D13
E13
F13
G13
H13
J13
K13
L13
M13
N13
P13
R13
D14
E14

L14
M14
N14
P14
R14
D15

K15
L15
M15
N15
P15
R15
D16
K16
L16
M16
D17
K17
L17
M17
K18
L18
M18

GND87 D18
L9
M9
N9
P9
R9

W2
W3
V4
V5
V6

GND86 D9
100nF
10uF 100nF 100nF 100nF 16V
6V3 16V 16V 16V
AVSS_PGA

GND3
GND4
GND5
GND6
GND7
GND8
GND9
GND10
GND11
GND12
GND13
GND14
GND15
GND16
GND17
GND18
GND19
GND20
GND21
GND22
GND23
GND24
GND25
GND26
GND27
GND28
GND29
GND30
GND31
GND32
GND33
GND34
GND35
GND36
GND37
GND38
GND39
GND40
GND41
GND42
GND43
GND44
GND45
GND46
GND47
GND48
GND49
GND50
GND51
GND52
GND53
GND54
GND55
GND56
GND57

GND58
GND59
GND60
GND61
GND62
GND63

GND64
GND65
GND66
GND67
GND68
GND69
GND70
GND71
GND72
GND73
GND74
GND75
GND76
GND77
GND78
GND79
GND80

GND81
GND82
GND83
GND84
GND85
F271

F295
A3V3_STBY A

MSD9WB9PT-2
AVDD_3V3

1k
60R C1030 C1024 C1025 C1022
10uF 100nF 100nF 100nF

AVDD_CVBS33_0
AVDD_CVBS33_1
6V3 16V 16V 16V 60R 402 ferrite secilecek

AVDD_ADC25_0
AVDD_ADC25_1

AVDD_REF25_0
AVDD_REF25_1

AVDD_MOD25_0
AVDD_MOD25_1

AVDD_ALIVE_0
AVDD_ALIVE_1
AVDD_ALIVE_2

U5
AVDD_PGA25

AVDD_DMPLL

AVDD_EAR33

AVDD_DDR_0
AVDD_DDR_1
AVDD_DDR_2
AVDD_DDR_3
AVDD_DDR_4
AVDD_AU25

AVDD_AU33

G15 AVDD_LPLL
H14 DVDD_DDR

K14 AVDD_126

PGA_VCOM
F305
2V5_VCC AVDD2V5_ADC

BYPASS
F272
H

VDDC0
VDDC1
VDDC2
VDDC3
VDDC4
VDDC5
VDDC6

G16 VDDP0
G17 VDDP1
1V8_VCC AVDD_DDR C1028 1k C1009 C1223
60R C990 100nF 100nF 10uF 100nF 100nF
22uF 6V3 16V 16V
6V3 16V 16V

H15
H16
H17
J14
J15
J16
J17

E15
E16
E17
F16
F17
N7
N8

P7
P8

T8

R7
R8

U8

V8

E8
F8
G8

G9

E9
F9

J8

H8

K9
F306
C1004 C1001 AVDD2V5_REF
1k C1008 C1224 1uF
100nF 100nF
6V3

AVSS_PGA
F270 F307 16V 16V

AVDD_2V5_PGA
C974

VDDC_1V2

AVDD2V5_ADC

AVDD2V5_REF

AVDD2V5_AUD

AVDD2V5_MOD

VDD_3V3

AVDD_DDR
3V3_VCC VDD_3V3 AVDD2V5_AUD
60R 1k

AVDD_3V3
C1029 C1014 C1221
10uF 100nF 100nF
6V3 16V F308 16V
B AVDD2V5_MOD B
G 1k C1222
100nF
C1225
100nF
16V 16V

R1649
2
33k
1
VDD_AUDIO_PWR

2
POWER SOCKET 10k

BAW56
D185
1 2

PW04 LOW POWER Option SHORT CCT PROTECTION


R1631
22uF

3
16V

R1727
C7

U1 AP211H 2
33k
1
12V_VCC

1
LM1117
20 19 R1750
3 IN OUT 2 3V3_STBY
5V_STBY 22k
3V3_VCC 18 17 3V3_VCC 3V3_STBY
F ADJ VOUT
3V3_VCC

2
3V3_STBY 16 15 1 4
VDD_AUDIO_PWR R1635

BAW56
D186
2 1
10k 3

12V_VCC/STBY 14 13 12V_VCC/STBY

PROTECT
C 5V_VCC C

1
5V_VCC 12 11 5V_VCC

TP202
3V3_TUNER
12V_VCC/STBY 10 9 5V_STBY
22uF

2
1
16V

R1636 ADAPTOR OVER VOLTAGE PROTECTION

BAW56
C6

D184
DIMMING Q180
8 7 1
10k
2
R40

1
2 3
BC858B
20k 12V_STBY

3V3_VCC
3
6 5 BACKLIGHT_ON/OFF Q178 R21

1
C971
DIMMING CIRCUIT
3
2

100nF R1638 R20 10k


1
STBY_ON/OFF
E
2
4 3 10V 1
10k
2
10k
1
3V3_STBY
2

3
S7 BC848B U7 VCC

2
1
2 1 Q211

R1639
3
LM809 RST GND

10k
CN706 S8 1
2
R1973 2 1

2
100R

1
VDD_AUDIO_PWR R1158
R1221
Q193 BC848B

1k
1
MEGA_DCR_OUT 1
4k7
2
2
BC858B
R1761
C839 3
100R
1

NC 8 1
S17

1 2 R1
D 220pF 7 R2 2 D
50V R1679
LNB CIRCUIT
3

S16 R1165 100R DIMMING


BACKLIGHT_DIM 1 2 2
Q189 6 R3 3 1N4001
4k7
D BC848B
5 R4 4
C838 1
C70 10V C69 D7
S18 3

MEGA_DCR_IN 1 2 R1166 C774 470nF 220uF 1uF


1
4k7
2 2
Q188 10uF 25V C65 50V
NC 220pF BC848B
50V 10V

R42
2k2
4k7
R41

15nF C68
C840 1

S10

SK24
12V_VCC/STBY

D8
12V_VCC 1 2

50V
220pF L2 27 22
S19 50V V_UP VO_TX
12V_VCC 4 LX EXTM 13
12V_STBY
F302 10uH 19 VCC VO_RX 21 LNB_OUT
3V3_VCC
1 2
12V_VCC 18 VCC_L PDC 11 C12
60R 6 12

1N5819
SDA_SYS SDA DSQIN 220nF

TP213
9
C

D6
S21 F289 SCL_SYS SCL 25V
14 1
12V_VCC/STBY
PANEL SUPPLY SWITCH
1 2

12V_VCC C13 TTX NC_1


60R 29 2
E 220nF
30
RSV_1 NC_2
3 E
F288 25V RSV_2 NC_3
1

S22

DISEQC_OUT
7

R19
10k

10k
R18
1 2

12V_STBY 5V_VCC PANEL_VCC NC_4


60R U6 NC_5 8
LNBH23L 16
4

F290 NC_6
12V_VCC
1 2
NC_7 17
FDC642P

23
2

60R
Q199

NC_8
R1734

24
33k

3V3_VCC
NC_9
C1128

25
1uF
25V
3V3_VCC

NC_10
NC_11 26
1

3V3_STBY

I_SEL
P_GND
A_GND
31
3

ADDR
R1725 NC_12

BYP
1 2
NC_13 32
47R
B

R1676
4k7

10
15
28

20
R1749

5
22k

R1677 3V3_VCC
2

STBY_ON/OFF

1
1 2
4k7
R1678
4k7

15k
R43
3
C14
3 R1748 220nF
NC STBY_ON/OFF_NOT
2
Q191 25V
1

1 2

S82 R1693 4k7


Q190 BC848B
F F
1 2 2 1 2

10k
BC848B 1

3 C1042 2
1

R1685 100nF
PANEL_VCC_ON/OFF
2
10k
1 2
Q194
10V
1

BC848B
1

VESTEL PROJECT NAME : 17mb62-2v3 A3


A SCH NAME :POWER_1&LNBP T. SHT:
DRAWN BY :<YOUR NAME HERE> 27-10-2011_09:04
1 2 3 4 5 6 7 8 AX M

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

72
LC-22LE240

POWER_2 Diagram
1 2 3 4 5 6 7 8
I ADAPTER SOCKET FS3
W_ADAPTER 1 2
12V_STBY

TP239
5 7A/32VDC
POWER BLOCK DIAGRAM
W/ADAPTOR
4 FS2
1 2
12V_INV

1
3 7A/32VDC
JK9 SW1

6
A A

TP243
12V_STBY 12V_VCC

DC/DC1

FDC604P
2 DC-DC4

Q1
1
C1038 SW2 DC 1V2_VCC

1
1

TP36 F9 100nF 5V_VCC DC-DC1 DC


H U174

1
1 2

12V_VCC C1112 5V_STBY


MP1583 DC 5V_STBY

6
60R 10nF
2

16V
F287 0R 1 8 DC
1

16V BS SS R1972

FDC604P
2 7 SW2

1
12V_STBY

Q198
1 2

12V_STBY IN EN 2
10k
1
R1709

C1047

220nF

R1729
3 6 5V_VCC

33k
60R
C1091 C1092 C1037 SW COMP R1690 3k9
1 2
25V
1 2

22uF 100nF 4 5 LDO2


4

6
22uF GND FB

1
1 2
10k 5n6F
16V 16V 16V DC-DC2 3V3_TUN

2
R1722
FDC642P
50V LDO

1
Q2
NC C1130 1
47R
2

DC 3V3_STBY
DC
CCFL INVERTER SOCKET

R1737

R1728
SW3

33k

1k
F7
3V3_VCC
3

1 2
5V_VCC
60R
CN705
G B L118
1
F6
2
3
DC-DC3 B
1 12V_INV 1 2
5V_STBY R1698
1 TP37 15uH C1102 C1103 60R MOSFET_CONTROL
2
10k 1 2
Q184
BC848B DC 1V8_VCC

2
2 22uF 22uF

D197

SS33
16V 16V
1 DC
3
INVERTER SOCKET W/ADAPTER LDO1

1
1 TP39
4 2V5_VCC
S1 LDO
5 DIMMING
S6
6 BACKLIGHT_ON/OFF
1

F
W/ADAPTOR & W/IPS16&17&60&PW25&PW06
TP45
TP46

C
SW1 DC/DC2 SW3 C

C1036
100nF
FS5 FS4

TP238

10V
1 2
12V_VCC F10 30068939
1 2
3V3_VCC
1 2

12V_STBY 7A/32VDC 12V_VCC C1114 3V3_STBY 7A/32VDC


1 BS SS 8
4

6
60R 2

1
4A 10nF
2A
U23
1

F286 16V R1689


FDC642P

FDC604P
1
2 IN EN 7
1

1
12V_STBY
Q200

Q197
1 2 2 1
12V_STBY 10k
C1049

220nF

R1732

C1048

220nF

R1731
2

2
25V

33k

25V

33k
60R C1089 C1090 MP1484 C1129 R1708
E 22uF 22uF 3 SW COMP 6 5k6
1

1
1 2

16V 16V 3N3 R3


2

2
R1724 5n6F R1723
4 GND FB 5
3

1
1
47R
2

50V 6k8 1
47R
2
1
R1733

R1730
33k

10k
for 3v3 Panel Sup.

R1735

TP244
22k
L123 NC F12
1 2
2

1 2
3V3_VCC
15uH 60R
3 3

R1692 L16 F11 R1697

1
Q182 Q183
D D
2 1 2 2

MOSFET_CONTROL
2
10k
1
3V3_STBY MOSFET_CONTROL
2
10k 1

BC848B 10uH 60R BC848B


C1096 C1097
1 1
22uF 22uF
6V3 6V3
D

COMMON DC/DC4
C
LDO1 DC/DC3
E
LDO2 E

C1035
100nF
10V
R1738 R1769 30068939
U175 3V3_STBY 20k 100k
LM1117 C1113
F303
2
1 BS SS 8

1
10nF
5V_VCC
1 2 3 IN OUT 2 2V5_VCC C1107 R1770 F273 16V
1

U173 R1691
U2 AP211H
TP241

6 EN LM1117
60R FB 1 2 IN EN 7 12V_VCC
1 2

C1033 150k 12V_VCC


2
10k
1
F300
C1080

100uF

GND VOUT
1

3 IN OUT 2
2
6V3

22uF U176 60R C1085 C1084 MP1484 C1131 R1710 5V_VCC


1 2
3V3_TUNER
150K
R1721

1uF
100R

1 4 6V3 5 VIN GND 2 10UH 22uF 22uF 3 SW COMP 6 1 2 330R


3k9 C1212
2

C1079
6V3 ADJ VOUT C1034

22uF
1 2

6V3
2

F291 MP2012 L116 16V 16V R1686 22uF 100nF


1

4 PVIN 5n6F
SW 3 4 GND FB 5 1 4 1
3V3_VCC 1 2
1V8_VCC 39k 6V3 10V
1

60R 10uH 50V


1
100R 2 R1768
R1720 C1093 C1094 C1101 C1098 1k
B 22uF 22uF 22uF 22uF 100R

TP231
1 2

6V3 6V3 6V3 6V3 R25

R1736
22k
NC

1
S89

100R
R24
STBY_ON/OFF L117

1
1

7 R2 2

6 R3 3

5 R4 4

1V2_VCC
R1979
100R

10uH
R1

2
S83 C1087 C1086
F STBY_ON/OFF_NOT MOSFET_CONTROL 22uF 22uF F
8

6V3 6V3
C1217

10nF

VESTEL PROJECT NAME : 17mb62-2v3


50V

A3
A SCH NAME :POWER_2 T. SHT:8
DRAWN BY :<YOUR NAME HERE> 27-10-2011_09:04
1 2 3 4 5 6 7 8 AX M

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

73
LC-22LE240

POWER SUPPLY Diagram

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

74
LC-22LE240

Led Converter Diagram

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

75
LC-22LE240

24. PRINTED WIRING BOARD

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

76
LC-22LE240

PRICE
REF No. PARTS DESCRIPTION * CODE
Q173 30001458 TR BC858B SMD G --
PARTS LISTING Q174 30001458 TR BC858B SMD G --
REPLACEMENT PARTS
Q178 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
Replacement parts which have special safety characteristics are identified in this manual.
Electrical components having such features are identified by ! in the Replacement Parts Listing. Q180 30001458 TR BC858B SMD G --
The use of a substitute replacement part which does not have the same safety characteristics Q181 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
as the factory recommended is not permitted.
Replacement parts not shown in this service manual may create shock fire, or other hazards. Q182 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
Q183 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
HOW TO ORDER REPLACEMENT PARTS
Q185 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
To have your order completed promptly and correctly please supply the following information.
1. MODEL NUMBER 2. REF. NO. 3. PART NO. Q186 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
4. DESCRIPTION 5. CODE 6. QUANTITY
Q188 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
Q189 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
Q190 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
Q191 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
MARK * : SPARE DELIVERY SECTION (G: EPC SHARP GmbH)
PRICE Q192 30010733 TR NMOS 2N7002 0.115A/60V SOT23 ROHS G --
REF No. PARTS DESCRIPTION * CODE Q193 30001458 TR BC858B SMD G --
Q194 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
LC22LE240E-EV-RU LCD PANEL
Q195 30001458 TR BC858B SMD G --
NOTE : THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY
Q197 30071823 TR PMOS uPA1917 -4.7A/-20V SSOT6 ROHS G --
30072972 TFT 22FHD50HZ ELED LG LC215EUE TEA1 (CN) G --
Q199 30018060 TR PMOS FDC642P -4A/-20V SSOT6 ROHS G --

PRINTED WIRING BOARDS Q200 30018060 TR PMOS FDC642P -4A/-20V SSOT6 ROHS G --
Q202 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
23028965 CHS.ASSY.17MB62-F2K1232H29222212153BG ( Main Board) G --
Q204 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
20565343 MD.ASY.17LD98-7-19942(MB25(SHA)RED/GREEN (Led Board)G --
Q208 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
¡ 23030194 MD.ASY.17PW80-24VA MB62_ROC_SHA (Power Board) G --
Q209 30069749 TR NMOS BSH105 1.05A/20V SOT23 ROHS G --
23001054 MD.ASY.17CON08-21.5''LG SDA1 ( Converter Board) G --
Q210 30010733 TR NMOS 2N7002 0.115A/60V SOT23 ROHS G --
LC-22LE240E-EV-RU - MB62
MAIN UNIT DIODES
D1 30070436 DIODE SMD ARRAY ESD CDA4C16GTH 0508 RoHS G --
INTEGRATED CIRCUITS D165 30042066 DIODE SMDSCH1N5819 1A/40V/25A SOD123ROHS G --
U145 30062776 DIODE SMD ESD AZ1045-04S SOT23-6 ROHS G -- D171 30038480 DIODE SMD ZEN C5.6V SOD123 ROHS G --
U155 30070769 IC DDR2 64Mx16 K4T1G164QF-BCF8 BGA84 ROH G -- D178 30038478 DIODE SMD ZEN C15V SOD123 ROHS G --
U158 30070314 IC FLASH SPI 8Mb MX25L8006E SO8 ROHS G -- D184 30048473 DIODE DUALSMD BAW56 4A/75V/4A SOT23ROHS G --
U162 30072037 IC NAND 512Mb NAND512W3A2SN6F TSOP48 ROH G -- D185 30048473 DIODE DUALSMD BAW56 4A/75V/4A SOT23ROHS G --
U163 30067953 IC AAMP AZAD2102 1x2.9W WCSP-9 RoHS G -- D186 30048473 DIODE DUALSMD BAW56 4A/75V/4A SOT23ROHS G --
U164 30067953 IC AAMP AZAD2102 1x2.9W WCSP-9 RoHS G -- D189 30038507 DIODE SMD 1N4148 0.15A/100V SOD123 RoHS G --
U173 30070995 IC STEP DOWN RT8293A ADJ/3A SO8 RoHS G -- D191 30038507 DIODE SMD 1N4148 0.15A/100V SOD123 RoHS G --
U175 30060344 IC LDO LM1117 ADJ/1A DPAK ROHS G -- D2 30070436 DIODE SMD ARRAY ESD CDA4C16GTH 0508 RoHS G --
U176 30066926 IC STEP DOWN MP2012 ADJ/1.5A QFN6 RoHS G -- D203 30038480 DIODE SMD ZEN C5.6V SOD123 ROHS G --
U178 30057644 IC DOPAMP TL062 SO8 RoHS G -- D204 30038502 DIODE SMD ZEN B5.1V SOD123 ROHS G --
U2 30069495 IC LDO AP2111H 3.3V/600MA SOT223 ROHS G -- D205 30038479 DIODE SMD ZEN C3V6 SOD123 ROHS G --
U23 30070783 IC STEP DOWN AP3503 ADJ/3A SO8 RO G -- D206 30038479 DIODE SMD ZEN C3V6 SOD123 ROHS G --
U5 30070454 IC MSD9WB9PT-2-SS BGA380 RoHS G -- D3 30070436 DIODE SMD ARRAY ESD CDA4C16GTH 0508 RoHS G --
U5 40045953 SUPER THIN POWDER (17.5*17.5*2)Rohs G -- D4 30070436 DIODE SMD ARRAY ESD CDA4C16GTH 0508 RoHS G --
U8 30068149 IC POWER SW ADJ FPF2124 SOT23-5 ROHS G -- D5 30062776 DIODE SMD ESD AZ1045-04S SOT23-6 ROHS G --

TRANSISTORS PACKAGED CIRCUITS


Q119 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G -- X2 30057263 XTAL SMD 24MHz 22pF 30ppm 25OhmHC49S RHS G --
Q133 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
Q146 30001458 TR BC858B SMD G -- COILS AND FILTERS
Q160 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G -- L116 30058702 COIL SMD 10uH 2.5A M 0R4 7x7(SHL)Ro G --
Q170 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G -- L117 30058702 COIL SMD 10uH 2.5A M 0R4 7x7(SHL)Ro G --
Q171 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G -- L119 30025158 COIL SMD 4.7uH 0.03A M 1R 805 Ro G --

77
LC-22LE240

PRICE PRICE
REF No. PARTS DESCRIPTION * CODE REF No. PARTS DESCRIPTION * CODE
L120 30025158 COIL SMD 4.7uH 0.03A M 1R 805 Ro G -- C1009 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G --
L123 30057938 COIL SMD 22uH 3.6A M 35R12x12(SHL)Ro G -- C1014 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G --
L124 30072017 COIL SMD 10uH 2A5 M 0R06 6X6X4.5 (SHL)Ro G -- C1015 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
L125 30072017 COIL SMD 10uH 2A5 M 0R06 6X6X4.5 (SHL)Ro G -- C1016 30044848 CAP SMD 100NF 16V K X7R (0402) ROHS G --
L126 30072017 COIL SMD 10uH 2A5 M 0R06 6X6X4.5 (SHL)Ro G -- C1022 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G --
L127 30072017 COIL SMD 10uH 2A5 M 0R06 6X6X4.5 (SHL)Ro G -- C1024 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G --
F11 30001734 RES SMD 1/10W 0R 0805 ROHS G -- C1025 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G --
F179 30063648 FERRIT SMD 120/100MHz 0.09R M1.2A 0402Ro G -- C1028 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G --
F181 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1029 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G --
F187 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1030 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G --
F200 30020530 FERRIT SMD 600R/100MHz 0.5R M 0.2A 603Ro G -- C1031 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --
F201 30020530 FERRIT SMD 600R/100MHz 0.5R M 0.2A 603Ro G -- C1032 30064117 CAP SMD 10UF 16V K X5R (0805) RoHS G --
F202 30066582 FERRIT SMD 1K/100MHz 1R5 M 50mA 603Ro G -- C1033 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --
F203 30066582 FERRIT SMD 1K/100MHz 1R5 M 50mA 603Ro G -- C1034 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
F205 30020530 FERRIT SMD 600R/100MHz 0.5R M 0.2A 603Ro G -- C1035 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
F206 30020530 FERRIT SMD 600R/100MHz 0.5R M 0.2A 603Ro G -- C1036 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
F248 30020530 FERRIT SMD 600R/100MHz 0.5R M 0.2A 603Ro G -- C1042 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
F259 30020530 FERRIT SMD 600R/100MHz 0.5R M 0.2A 603Ro G -- C1048 30010560 CAP SMD 220NF 25V K X7R (0805) ROHS G --
F270 30001734 RES SMD 1/10W 0R 0805 ROHS G -- C1049 30010560 CAP SMD 220NF 25V K X7R (0805) ROHS G --
F271 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1058 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G --
F272 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1070 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G --
F273 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1079 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --

F274 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1080 30010594 CAP ELCH 100UF 16V M 86mA 6.3x5.4 ROHS G --

F277 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1081 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G --

F286 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1084 30067595 CAP SMD 22UF 16V M X5R (1206) RoHS G --

F288 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1085 30067595 CAP SMD 22UF 16V M X5R (1206) RoHS G --

F289 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1086 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --

F291 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1087 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --

F294 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G -- C1089 30067595 CAP SMD 22UF 16V M X5R (1206) RoHS G --
C1090 30067595 CAP SMD 22UF 16V M X5R (1206) RoHS G --
F295 30063648 FERRIT SMD 120/100MHz 0.09R M1.2A 0402Ro G --
C1093 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --
F300 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G --
C1094 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --
F301 30020530 FERRIT SMD 600R/100MHz 0.5R M 0.2A 603Ro G --
C1096 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --
F303 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G --
C1097 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --
F305 30063648 FERRIT SMD 120/100MHz 0.09R M1.2A 0402Ro G --
C1098 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --
F306 30063648 FERRIT SMD 120/100MHz 0.09R M1.2A 0402Ro G --
C1101 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --
F307 30063648 FERRIT SMD 120/100MHz 0.09R M1.2A 0402Ro G --
C1107 30050554 CAP SMD 1UF 6.3V M X5R (0402) RoHS G --
F308 30063648 FERRIT SMD 120/100MHz 0.09R M1.2A 0402Ro G --
C1113 30022342 CAP SMD 10NF 16V J X7R (0402) ROHS G --
F5 30020530 FERRIT SMD 600R/100MHz 0.5R M 0.2A 603Ro G --
C1114 30022342 CAP SMD 10NF 16V J X7R (0402) ROHS G --
F8 30019087 FERRIT SMD 60R/100MHz 0.025 M 3A 0805Roh G --
C1128 30020142 CAP SMD 1UF 25V Z Y5V (0805) RoHS G --
FS4 30072150 FUSE SAFE SMD 3A 32V DC (1206)_MB62 ROHS G --
C1129 30022339 CAP SMD 5.6NF 50V J X7R (0402) ROHS G --
FS5 30062423 FUSE SAFE SMD 4A/32VDC UF HMELT 1206RoHS G --
C1131 30022339 CAP SMD 5.6NF 50V J X7R (0402) ROHS G --
TUNER C1168 30010594 CAP ELCH 100UF 16V M 86mA 6.3x5.4 ROHS G --
TU3 30070628 TUNER SILICAN HNIM SUT-RE216 RoHS G -- C1169 30010594 CAP ELCH 100UF 16V M 86mA 6.3x5.4 ROHS G --
C1170 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G --
CAPACITORS C1171 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G --
C1001 30044848 CAP SMD 100NF 16V K X7R (0402) ROHS G -- C1172 30022342 CAP SMD 10NF 16V J X7R (0402) ROHS G --
C1004 30044848 CAP SMD 100NF 16V K X7R (0402) ROHS G -- C1174 30044848 CAP SMD 100NF 16V K X7R (0402) ROHS G --
C1005 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- C1175 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
C1007 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- C1176 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
C1008 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- C1177 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G --

78
LC-22LE240

PRICE PRICE
REF No. PARTS DESCRIPTION * CODE REF No. PARTS DESCRIPTION * CODE
C1178 30022244 CAP SMD 100PF 50V J COG (0402) ROHS G -- C658 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
C1179 30022244 CAP SMD 100PF 50V J COG (0402) ROHS G -- C663 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
C1180 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G -- C664 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
C1181 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G -- C665 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
C1182 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G -- C666 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G --
C1183 30022338 CAP SMD 4.7NF 50V J X7R (0402) RoHS G -- C683 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1184 30022338 CAP SMD 4.7NF 50V J X7R (0402) RoHS G -- C687 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1185 30022244 CAP SMD 100PF 50V J COG (0402) ROHS G -- C7 30067595 CAP SMD 22UF 16V M X5R (1206) RoHS G --
C1186 30022244 CAP SMD 100PF 50V J COG (0402) ROHS G -- C709 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1187 30022196 CAP SMD 470PF 50V J X7R (0402) ROHS G -- C710 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1188 30022196 CAP SMD 470PF 50V J X7R (0402) ROHS G -- C711 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1189 30022196 CAP SMD 470PF 50V J X7R (0402) ROHS G -- C712 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1190 30022196 CAP SMD 470PF 50V J X7R (0402) ROHS G -- C713 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1195 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G -- C714 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1196 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G -- C715 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1197 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G -- C716 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1198 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G -- C718 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G --
C1199 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G -- C729 30022342 CAP SMD 10NF 16V J X7R (0402) ROHS G --
C120 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- C782 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G --
C1200 30047294 CAP SMD 4.7UF 10V K X5R (0805) ROHS G -- C794 30022351 CAP SMD 47NF 16V J X5R (0402) ROHS G --
C1201 30050554 CAP SMD 1UF 6.3V M X5R (0402) RoHS G -- C795 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G --
C1202 30050554 CAP SMD 1UF 6.3V M X5R (0402) RoHS G -- C796 30022351 CAP SMD 47NF 16V J X5R (0402) ROHS G --
C1203 30050554 CAP SMD 1UF 6.3V M X5R (0402) RoHS G -- C797 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G --
C1212 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G -- C798 30022351 CAP SMD 47NF 16V J X5R (0402) ROHS G --
C1214 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G -- C799 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G --
C1215 30022338 CAP SMD 4.7NF 50V J X7R (0402) RoHS G -- C802 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G --
C1220 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- C803 30022351 CAP SMD 47NF 16V J X5R (0402) ROHS G --
C1221 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- C804 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G --
C1222 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- C805 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G --
C1223 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- C806 30022351 CAP SMD 47NF 16V J X5R (0402) ROHS G --
C1224 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- C807 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G --
C1225 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- C808 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G --
C1226 30020142 CAP SMD 1UF 25V Z Y5V (0805) RoHS G -- C809 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G --
C1227 30020142 CAP SMD 1UF 25V Z Y5V (0805) RoHS G -- C810 30022351 CAP SMD 47NF 16V J X5R (0402) ROHS G --
C1228 30020142 CAP SMD 1UF 25V Z Y5V (0805) RoHS G -- C823 30022237 CAP SMD 27PF 50V J COG (0402) ROHS G --
C1229 30020142 CAP SMD 1UF 25V Z Y5V (0805) RoHS G -- C828 30022237 CAP SMD 27PF 50V J COG (0402) ROHS G --
C15 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- C829 30022237 CAP SMD 27PF 50V J COG (0402) ROHS G --
C378 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G -- C830 30022248 CAP SMD 220PF 50V J COG (0402) RoHS G --
C6 30067595 CAP SMD 22UF 16V M X5R (1206) RoHS G -- C831 30022248 CAP SMD 220PF 50V J COG (0402) RoHS G --
C602 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G -- C832 30022248 CAP SMD 220PF 50V J COG (0402) RoHS G --
C608 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G -- C833 30022248 CAP SMD 220PF 50V J COG (0402) RoHS G --
C61 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G -- C835 30022248 CAP SMD 220PF 50V J COG (0402) RoHS G --
C610 30067872 CAP SMD 10UF 10V M X5R (0805) ROHS G -- C836 30022248 CAP SMD 220PF 50V J COG (0402) RoHS G --
C612 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G -- C838 30022248 CAP SMD 220PF 50V J COG (0402) RoHS G --
C615 30065929 CAP ELCH 220UF 10V M 150mA 8x6.5 ROHS G -- C839 30022248 CAP SMD 220PF 50V J COG (0402) RoHS G --
C617 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G -- C840 30022248 CAP SMD 220PF 50V J COG (0402) RoHS G --
C630 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- C853 30022336 CAP SMD 3.3NF 50V J X7R (0402) ROHS G --
C653 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- C854 30022336 CAP SMD 3.3NF 50V J X7R (0402) ROHS G --
C654 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- C855 30022336 CAP SMD 3.3NF 50V J X7R (0402) ROHS G --
C656 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- C856 30022336 CAP SMD 3.3NF 50V J X7R (0402) ROHS G --
C657 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- C857 30022338 CAP SMD 4.7NF 50V J X7R (0402) RoHS G --

79
LC-22LE240

PRICE PRICE
REF No. PARTS DESCRIPTION * CODE REF No. PARTS DESCRIPTION * CODE
C858 30022338 CAP SMD 4.7NF 50V J X7R (0402) RoHS G -- R1187 30022140 RES SMD 1/16W 22K F (0402) RoHS G --
C859 30030099 CAP SMD 1NF 50V K X7R (0402) ROHS G -- R1198 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
C860 30022240 CAP SMD 47PF 50V J COG (0402) ROHS G -- R12 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
C861 30030099 CAP SMD 1NF 50V K X7R (0402) ROHS G -- R1206 30022051 RES SMD 1/16W 2.7K J 0402 ROHS G --
C862 30030099 CAP SMD 1NF 50V K X7R (0402) ROHS G -- R1209 30022051 RES SMD 1/16W 2.7K J 0402 ROHS G --
C868 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G -- R1221 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
C870 30065929 CAP ELCH 220UF 10V M 150mA 8x6.5 ROHS G -- R1233 30022118 RES SMD 1/16W 75R J 0402 RoHS G --
C881 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G -- R124 30000588 RES SMD 1/10W 220R J 0805 ROHS G --
C882 30022351 CAP SMD 47NF 16V J X5R (0402) ROHS G -- R1243 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
C883 30022351 CAP SMD 47NF 16V J X5R (0402) ROHS G -- R1244 30022020 RES SMD 1/16W 560R F 0402 RoHS G --
C884 30022351 CAP SMD 47NF 16V J X5R (0402) ROHS G -- R1245 30022020 RES SMD 1/16W 560R F 0402 RoHS G --
C885 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G -- R1248 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
C886 30062359 CAP SMD 47NF 16V K X7R (0402) ROHS G -- R1249 30021960 RES SMD 1/16W 47R J 0402 ROHS G --
C904 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- R1265 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
C905 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- R1309 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
C906 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- R1310 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
C910 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- R1311 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
C912 30022347 CAP SMD 22NF 16V J X7R (0402) ROHS G -- R1313 30022058 RES SMD 1/16W 22R J 0402 ROHS G --
C913 30051167 CAP SMD 220NF 10V X7R K (0402) ROHS G -- R1332 30022058 RES SMD 1/16W 22R J 0402 ROHS G --
C942 30030099 CAP SMD 1NF 50V K X7R (0402) ROHS G -- R1355 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
C943 30030099 CAP SMD 1NF 50V K X7R (0402) ROHS G -- R1356 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
C944 30030099 CAP SMD 1NF 50V K X7R (0402) ROHS G -- R1357 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
C945 30030099 CAP SMD 1NF 50V K X7R (0402) ROHS G -- R1358 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
C949 30022237 CAP SMD 27PF 50V J COG (0402) ROHS G -- R1364 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
C951 30022238 CAP SMD 33PF 50V J COG (0402) ROHS G -- R1365 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
C952 30022238 CAP SMD 33PF 50V J COG (0402) ROHS G -- R1366 30041373 RES NET 1/16W 22R J 8P 0402 ROHS G --
C959 30022351 CAP SMD 47NF 16V J X5R (0402) ROHS G -- R1367 30041373 RES NET 1/16W 22R J 8P 0402 ROHS G --
C965 30022132 RES SMD 1/16W 0R 0402 ROHS G -- R1368 30041373 RES NET 1/16W 22R J 8P 0402 ROHS G --
C967 30022167 CAP SMD 4.7PF 50V J COG (402) ROHS G -- R1369 30041373 RES NET 1/16W 22R J 8P 0402 ROHS G --
C968 30022165 CAP SMD 3.3PF 50V J COG (0402) RoHS G -- R1370 30041373 RES NET 1/16W 22R J 8P 0402 ROHS G --
C970 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G -- R1380 30041373 RES NET 1/16W 22R J 8P 0402 ROHS G --
C971 30030097 CAP SMD 100NF 10V K X5R (0402) RoHS G -- R1382 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
C974 30050554 CAP SMD 1UF 6.3V M X5R (0402) RoHS G -- R1383 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
C990 30047296 CAP SMD 22UF 6.3V M X5R (0805) ROHS G -- R1384 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
C997 30050558 CAP SMD 100NF 16V K X5R (0402) ROHS G -- R1385 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R1388 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
RESISTORS R1389 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R1 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1390 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R10 30022132 RES SMD 1/16W 0R 0402 ROHS G -- R1392 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R102 30022098 RES SMD 1/16W 390R J 0402 RoHS G -- R1393 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R103 30022112 RES SMD 1/16W 68K J 0402 RoHS G -- R1394 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R104 30022084 RES SMD 1/16W 33K J 0402 RoHS G -- R1395 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R1149 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1396 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R1158 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1397 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R1165 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1398 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R1166 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1399 30042505 RES NET 1/32W 33R J 8P 0402 ROHS G --
R1171 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1401 30022085 RES SMD 1/16W 33R J 0402 RoHS G --
R1172 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1402 30022085 RES SMD 1/16W 33R J 0402 RoHS G --
R1177 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1408 30070980 FERRIT SMD 220R/100Mhz 0.35R M 0.3A 402R G --
R1182 30021986 RES SMD 1/16W 4.7K F 0402 ROHS G -- R1409 30070980 FERRIT SMD 220R/100Mhz 0.35R M 0.3A 402R G --
R1183 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1411 30055434 RES SMD 1/16W 62R J 0402 ROHS G --

80
LC-22LE240

PRICE PRICE
REF No. PARTS DESCRIPTION * CODE REF No. PARTS DESCRIPTION * CODE
R1412 30055434 RES SMD 1/16W 62R J 0402 ROHS G -- R1615 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1415 30055434 RES SMD 1/16W 62R J 0402 ROHS G -- R1617 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1419 30070980 FERRIT SMD 220R/100Mhz 0.35R M 0.3A 402R G -- R1618 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1420 30022132 RES SMD 1/16W 0R 0402 ROHS G -- R1619 30022118 RES SMD 1/16W 75R J 0402 RoHS G --
R1421 30022132 RES SMD 1/16W 0R 0402 ROHS G -- R1620 30022118 RES SMD 1/16W 75R J 0402 RoHS G --
R1422 30022132 RES SMD 1/16W 0R 0402 ROHS G -- R1621 30022118 RES SMD 1/16W 75R J 0402 RoHS G --
R1423 30022003 RES SMD 1/16W 470R J 0402 ROHS G -- R1632 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
R1424 30022085 RES SMD 1/16W 33R J 0402 RoHS G -- R1635 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1425 30022085 RES SMD 1/16W 33R J 0402 RoHS G -- R1636 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1427 30022085 RES SMD 1/16W 33R J 0402 RoHS G -- R1638 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1479 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1639 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1480 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1642 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1481 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1661 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1482 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1662 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
R1483 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1663 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1486 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1666 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1489 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1667 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1494 30022003 RES SMD 1/16W 470R J 0402 ROHS G -- R1668 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
R1495 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1671 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1496 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1672 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1505 30022003 RES SMD 1/16W 470R J 0402 ROHS G -- R1676 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
R1512 30022085 RES SMD 1/16W 33R J 0402 RoHS G -- R1677 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1513 30022085 RES SMD 1/16W 33R J 0402 RoHS G -- R1678 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1514 30022085 RES SMD 1/16W 33R J 0402 RoHS G -- R1679 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1515 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1684 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1516 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1685 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1517 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1686 30022099 RES SMD 1/16W 39K J 0402 ROHS G --
R1524 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1689 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1527 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1691 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1528 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1692 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1530 30022132 RES SMD 1/16W 0R 0402 ROHS G -- R1693 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1533 30022043 RES SMD 1/16W 1M J 0402 ROHS G -- R1697 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1543 30021991 RES SMD 1/16W 100R J 0402 ROHS G -- R1699 30021958 RES SMD 1/16W 47K J 0402 RoHS G --
R1562 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1701 30021989 RES SMD 1/16W 100K J 0402 ROHS G --
R1563 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1702 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1567 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1704 30022088 RES SMD 1/16W 680R F 0402 ROHS G --
R1568 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1708 30021994 RES SMD 1/16W 10K F 0402 ROHS G --
R1569 30022056 RES SMD 1/16W 220R J 0402 RoHS G -- R1710 30021994 RES SMD 1/16W 10K F 0402 ROHS G --
R1570 30022056 RES SMD 1/16W 220R J 0402 RoHS G -- R1718 30021989 RES SMD 1/16W 100K J 0402 ROHS G --
R1571 30022056 RES SMD 1/16W 220R J 0402 RoHS G -- R1720 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1572 30022056 RES SMD 1/16W 220R J 0402 RoHS G -- R1721 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1587 30022118 RES SMD 1/16W 75R J 0402 RoHS G -- R1723 30021960 RES SMD 1/16W 47R J 0402 ROHS G --
R1597 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1724 30021960 RES SMD 1/16W 47R J 0402 ROHS G --
R1601 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1725 30021960 RES SMD 1/16W 47R J 0402 ROHS G --
R1603 30022058 RES SMD 1/16W 22R J 0402 ROHS G -- R1727 30022084 RES SMD 1/16W 33K J 0402 RoHS G --
R1605 30022084 RES SMD 1/16W 33K J 0402 RoHS G -- R1730 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1606 30022039 RES SMD 1/16W 18K F 0402 RoHS G -- R1731 30022084 RES SMD 1/16W 33K J 0402 RoHS G --
R1609 30041373 RES NET 1/16W 22R J 8P 0402 ROHS G -- R1732 30022084 RES SMD 1/16W 33K J 0402 RoHS G --
R1610 30041373 RES NET 1/16W 22R J 8P 0402 ROHS G -- R1733 30022084 RES SMD 1/16W 33K J 0402 RoHS G --
R1613 30041373 RES NET 1/16W 22R J 8P 0402 ROHS G -- R1734 30022084 RES SMD 1/16W 33K J 0402 RoHS G --
R1614 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1735 30022137 RES SMD 1/16W 27K F (0402) RoHS G --

81
LC-22LE240

PRICE PRICE
REF No. PARTS DESCRIPTION * CODE REF No. PARTS DESCRIPTION * CODE
R1736 30022140 RES SMD 1/16W 22K F (0402) RoHS G -- R1919 30022024 RES SMD 1/16W 12K J 0402 ROHS G --
R1738 30022053 RES SMD 1/16W 20K F 0402 ROHS G -- R1920 30022024 RES SMD 1/16W 12K J 0402 ROHS G --
R1748 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1921 30022024 RES SMD 1/16W 12K J 0402 ROHS G --
R1749 30022057 RES SMD 1/16W 22K J 0402 RoHS G -- R1924 30022057 RES SMD 1/16W 22K J 0402 RoHS G --
R1750 30022057 RES SMD 1/16W 22K J 0402 RoHS G -- R1925 30022057 RES SMD 1/16W 22K J 0402 RoHS G --
R1761 30038984 RES NET 1/32W 100R J 8P 0402 ROHS G -- R1926 30022116 RES SMD 1/16W 75K J 0402 ROHS G --
R1768 30064848 RES SMD 1/16W 3.3K F (0402) RoHS G -- R1927 30022116 RES SMD 1/16W 75K J 0402 ROHS G --
R1769 30021989 RES SMD 1/16W 100K J 0402 ROHS G -- R1928 30022053 RES SMD 1/16W 20K F 0402 ROHS G --
R1770 30022026 RES SMD 1/16W 150K J 0402 RoHS G -- R1929 30022053 RES SMD 1/16W 20K F 0402 ROHS G --
R1833 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1940 30022028 RES SMD 1/16W 150R J 0402 RoHS G --
R1835 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1941 30022041 RES SMD 1/16W 1K F 0402 ROHS G --
R1836 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1942 30022085 RES SMD 1/16W 33R J 0402 RoHS G --
R1838 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1949 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1840 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1950 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1854 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1951 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1855 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R1952 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1858 30022056 RES SMD 1/16W 220R J 0402 RoHS G -- R1953 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1859 30022056 RES SMD 1/16W 220R J 0402 RoHS G -- R1954 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1862 30021958 RES SMD 1/16W 47K J 0402 RoHS G -- R1959 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1863 30021958 RES SMD 1/16W 47K J 0402 RoHS G -- R1960 30022088 RES SMD 1/16W 680R F 0402 ROHS G --
R1870 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1963 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1871 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1967 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1872 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1968 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1873 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1969 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1874 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1970 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1875 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1971 30022124 RES SMD 1/16W 9.1K F (0402) ROHS G --
R1876 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1974 30063648 FERRIT SMD 120/100MHz 0.09R M1.2A 0402Ro G --
R1881 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1975 30063648 FERRIT SMD 120/100MHz 0.09R M1.2A 0402Ro G --
R1882 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1976 30063648 FERRIT SMD 120/100MHz 0.09R M1.2A 0402Ro G --
R1883 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1977 30022038 RES SMD 1/16W 180R J (0402) RoHS G --
R1884 30021999 RES SMD 1/16W 10R J 0402 RoHS G -- R1982 30022058 RES SMD 1/16W 22R J 0402 ROHS G --
R1889 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1983 30022058 RES SMD 1/16W 22R J 0402 ROHS G --
R1890 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1984 30022058 RES SMD 1/16W 22R J 0402 ROHS G --
R1896 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- R1985 30022058 RES SMD 1/16W 22R J 0402 ROHS G --
R1897 30021991 RES SMD 1/16W 100R J 0402 ROHS G -- R1986 30022058 RES SMD 1/16W 22R J 0402 ROHS G --
R1898 30022055 RES SMD 1/16W 220K J 0402 ROHS G -- R1987 30022058 RES SMD 1/16W 22R J 0402 ROHS G --
R1899 30022055 RES SMD 1/16W 220K J 0402 ROHS G -- R221 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1900 30021991 RES SMD 1/16W 100R J 0402 ROHS G -- R222 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1901 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R223 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1902 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R23 30021996 RES SMD 1/16W 10K J 0402 ROHS G --
R1903 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R24 30022132 RES SMD 1/16W 0R 0402 ROHS G --
R1904 30021996 RES SMD 1/16W 10K J 0402 ROHS G -- R29 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1907 30021991 RES SMD 1/16W 100R J 0402 ROHS G -- R3 30021994 RES SMD 1/16W 10K F 0402 ROHS G --
R1908 30022056 RES SMD 1/16W 220R J 0402 RoHS G -- R30 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1909 30022041 RES SMD 1/16W 1K F 0402 ROHS G -- R33 30022085 RES SMD 1/16W 33R J 0402 RoHS G --
R1912 30022041 RES SMD 1/16W 1K F 0402 ROHS G -- R34 30022085 RES SMD 1/16W 33R J 0402 RoHS G --
R1913 30022084 RES SMD 1/16W 33K J 0402 RoHS G -- R344 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R1914 30022084 RES SMD 1/16W 33K J 0402 RoHS G -- R45 30022060 RES SMD 1/16W 270R J 0402 ROHS G --
R1915 30022055 RES SMD 1/16W 220K J 0402 ROHS G -- R46 30022003 RES SMD 1/16W 470R J 0402 ROHS G --
R1916 30022055 RES SMD 1/16W 220K J 0402 ROHS G -- R47 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --
R1918 30022024 RES SMD 1/16W 12K J 0402 ROHS G -- R48 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G --

82
LC-22LE240

PRICE PRICE
REF No. PARTS DESCRIPTION * CODE REF No. PARTS DESCRIPTION * CODE
R49 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- IC701 30015087 IC SAFE OPTOCOUPLER TCET1102G G --
R5 30021991 RES SMD 1/16W 100R J 0402 ROHS G -- IC702 30067808 IC PWM CONT NCP1579 SO8 ROHS G --
R50 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- IC703 30066849 TR DNMOS FDS8984 7A/30V SO8 RoHS G --
R6 30021991 RES SMD 1/16W 100R J 0402 ROHS G --
R613 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- TRANSISTORS
R614 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- Q702 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
R620 30021991 RES SMD 1/16W 100R J 0402 ROHS G -- Q705 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
R623 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- Q706 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
R624 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- Q707 30070504 TR PMOS FDC658AP -4A/-30V SSOT6 ROHS G --
R7 30022051 RES SMD 1/16W 2.7K J 0402 ROHS G -- Q708 30072632 TR NMOS DMN3730 0.85A/30V SOT23 PW80 ROH G --
R793 30021960 RES SMD 1/16W 47R J 0402 ROHS G -- Q709 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
R8 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- Q710 30001453 TR NBJT BC337 0.8A/45V TO92 ROHS G --
R817 30021991 RES SMD 1/16W 100R J 0402 ROHS G -- Q711 30001458 TR BC858B SMD G --
R818 30021991 RES SMD 1/16W 100R J 0402 ROHS G -- Q712 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
R844 30021990 RES SMD 1/16W 4.7R J 0402 ROHS G -- Q713 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
R845 30021990 RES SMD 1/16W 4.7R J 0402 ROHS G -- Q715 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --
R9 30021987 RES SMD 1/16W 4.7K J 0402 RoHS G -- Q716 30001457 TR NBJT BC848B 0.1A/30V SOT23 ROHS G --

MISCELLANEOUS PARTS DIODES


CN1 30072383 SOCKET USB A TYPE FEMALE SIDE SMT TH RHS G -- D700 30001319 DIODE RL207 2A/1000V 70A DO-15 ROHS G --
CN139 30060746 CONN FFC 30P 1MM TOP LVDS ROHS G -- D701 30001319 DIODE RL207 2A/1000V 70A DO-15 ROHS G --
CN141 30067876 SOCKET PCMCIA S.DECK 4mm HEADERonly RoHS G -- D702 30001319 DIODE RL207 2A/1000V 70A DO-15 ROHS G --
CN703 30063090 CONN HEADER 5P 2.0MM SIDE W/LOCK RoHS G -- D703 30001319 DIODE RL207 2A/1000V 70A DO-15 ROHS G --
CN706 30066827 CONN FEMALE HEADER 2x10P 2.54 SIDE ROHS G -- D704 30001318 DIODE BA159 1A/800V 20A G --
CN707 30070082 SOCKET HDMI 19P 0.5MM TOP PIP ROHS G -- D705 30001318 DIODE BA159 1A/800V 20A G --
CN710 30066919 CONN HEADER 6P 2.0MM SIDE W/LOCK RoHS G -- D708 30043523 DIODE SCH SB5100 5A/100V/150A DO201 ROHS G --
CN711 30071149 SOCKET D-SUB 15P TOP PIP SHIELD RoHS G -- D709 30043523 DIODE SCH SB5100 5A/100V/150A DO201 ROHS G --
JK1 30071260 JACK HEADPHONE GREEN 3 POLE SIDE PIPROHS G -- D710 30043523 DIODE SCH SB5100 5A/100V/150A DO201 ROHS G --
JK10 30066835 JACK RCA 1P BLACK TOP RoHS G -- D712 30009366 DIODE UF5402 3A/200V 150A DO201AD RoHS G --
JK3 30071258 JACK HEADPHONE YLW 3 POLE SIDE PIP ROHS G -- D713 30009366 DIODE UF5402 3A/200V 150A DO201AD RoHS G --
JK6 30071259 JACK HEADPHONE BLK 3 POLE SIDE PIP ROHS G -- D716 30038478 DIODE SMD ZEN C15V SOD123 ROHS G --
PL1 35028251 GROUND TERMINAL Main Board 8.5X8.3 Rohs G -- D717 30038481 DIODE SMD ZEN C6.8V SOD123 ROHS G --
PL2 35028251 GROUND TERMINAL Main Board 8.5X8.3 Rohs G -- D718 30008996 IC VREF TL431SAMF2 ADJ %1 SOT23 R G --
PL3 35028251 GROUND TERMINAL Main Board 8.5X8.3 Rohs G -- D719 30038507 DIODE SMD 1N4148 0.15A/100V SOD123 RoHS G --
PL4 35028251 GROUND TERMINAL Main Board 8.5X8.3 Rohs G -- D725 30038480 DIODE SMD ZEN C5.6V SOD123 ROHS G --
S16 30022132 RES SMD 1/16W 0R 0402 ROHS G --
COILS AND FILTERS
S19 30001734 RES SMD 1/10W 0R 0805 ROHS G --
L700 30071121 LINE FILTER SAFE 2*23mH 1A 0R35 10mm ROH G --
S22 30001734 RES SMD 1/10W 0R 0805 ROHS G --
L701 30001992 COIL AXI 10uH 0.5A K 0R6 4x9.8 Ro G --
S38 30022132 RES SMD 1/16W 0R 0402 ROHS G --
L702 30067937 Choke Coil 1uH 5A Axial M 0.7R 10x5.5 Ro G --
S40 30022132 RES SMD 1/16W 0R 0402 ROHS G --
L703 30001734 RES SMD 1/10W 0R 0805 ROHS G --
S41 30022132 RES SMD 1/16W 0R 0402 ROHS G --
L705 30062563 Choke coil Toroid Safe 33uH 3A K 6x12Ro G --
S83 30022132 RES SMD 1/16W 0R 0402 ROHS G --
L706 30024779 FERRIT SMD 50R/100MHZ 0.4R M 3A 1206 ROH G --
S86 30022132 RES SMD 1/16W 0R 0402 ROHS G --
L709 30024779 FERRIT SMD 50R/100MHZ 0.4R M 3A 1206 ROH G --
S92 30022056 RES SMD 1/16W 220R J 0402 RoHS G --
L710 30024779 FERRIT SMD 50R/100MHZ 0.4R M 3A 1206 ROH G --
SC1 30070522 SOCKET SCART 21P TOP LEFT BLACK PIP ROHS G --
SW5 30072365 SWITCH PUSH&LEVER SMD PLJG4-KH ROHS G --
CAPACITORS
17PW80 C700 30069938 CAP CER SAFE 1NF 4KV M 3.5MMSHAROHS G --
LC-22LE240E-EV-RU - POWER SUPPLY C701 30069939 CAP CER SAFE 330PF 4KV M 3.5MMSHAROHS G --
C702 30068234 CAP MKP SAFE 100NF 275V M X2AC15BOX ROHS G --
INTEGRATED CIRCUITS C704 30069938 CAP CER SAFE 1NF 4KV M 3.5MMSHAROHS G --
IC700 30069010 IC SMPS ICE3BR0665J 65KHz DIP8 ROHS G -- C705 30070765 CAP EL 39UF 450V M 105C 375mA 10x50SHALE G --

83
LC-22LE240

PRICE PRICE
REF No. PARTS DESCRIPTION * CODE REF No. PARTS DESCRIPTION * CODE
C706 30070765 CAP EL 39UF 450V M 105C 375mA 10x50SHALE G -- R717 30039196 RES SMD 1/4W 1M F 1206 ROHS G --
C707 30068234 CAP MKP SAFE 100NF 275V M X2AC15BOX ROHS G -- R725 30007030 RES SMD 1/4W 1R J (1206) ROHS G --
C708 30068234 CAP MKP SAFE 100NF 275V M X2AC15BOX ROHS G -- R727 30060652 RES SMD 1/4W 100K J (1206) RoHS G --
C711 30069939 CAP CER SAFE 330PF 4KV M 3.5MMSHAROHS G -- R728 30060652 RES SMD 1/4W 100K J (1206) RoHS G --
C712 30010603 POWER G -- R729 30060652 RES SMD 1/4W 100K J (1206) RoHS G --
C713 30000284 CAP SMD 1NF 50V K X7R (0805) ROHS G -- R730 30060652 RES SMD 1/4W 100K J (1206) RoHS G --
C714 30066237 CAP MKP 4.7NF 630VDC/622VPP K 7.5BOXROHS G -- R731 30060652 RES SMD 1/4W 100K J (1206) RoHS G --
C715 30070588 CAP EL 47UF 35V M 105C 86mA 8x7SHARPROHS G -- R732 30060652 RES SMD 1/4W 100K J (1206) RoHS G --
C718 30000300 CAP SMD 1.5NF 50V K X7R (0805) ROHS G -- R733 30060652 RES SMD 1/4W 100K J (1206) RoHS G --
C719 30000294 CAP SMD 100NF 50V K X7R (0805) ROHS G -- R734 30060652 RES SMD 1/4W 100K J (1206) RoHS G --
C723 30068742 CAP SMD 1UF 50V K X7R (1206) ROHS G -- R735 30007030 RES SMD 1/4W 1R J (1206) ROHS G --
C724 30069937 CAP CER SAFE 2.2NF 4KV M 3.5MMSHAROHS G -- R737 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C725 30000284 CAP SMD 1NF 50V K X7R (0805) ROHS G -- R742 30001735 RES SMD 1/8W 0R 1206 ROHS G --
C728 30039384 CAP SMD 1NF 1KV K X7R (1206) ROHS G -- R744 30001735 RES SMD 1/8W 0R 1206 ROHS G --
C729 30070744 CAPEL 560UF 25V M105C1050mA 8X20SHALEFT G -- R754 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C730 30070744 CAPEL 560UF 25V M105C1050mA 8X20SHALEFT G -- R755 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C731 30070744 CAPEL 560UF 25V M105C1050mA 8X20SHALEFT G -- R756 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C732 30068742 CAP SMD 1UF 50V K X7R (1206) ROHS G -- R757 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C733 30068742 CAP SMD 1UF 50V K X7R (1206) ROHS G -- R761 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C734 30070745 CAPEL 560UF 50V M105C 1500mA 8X40SHALEFT G -- R762 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C737 30000284 CAP SMD 1NF 50V K X7R (0805) ROHS G -- R763 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C738 30000294 CAP SMD 100NF 50V K X7R (0805) ROHS G -- R764 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C739 30000289 CAP SMD 10NF 50V K X7R (0805) ROHS G -- R767 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C741 30000294 CAP SMD 100NF 50V K X7R (0805) ROHS G -- R774 30000593 RES SMD 1/10W 2.2K J 0805 ROHS G --
C743 30061026 CAP SMD 1UF 25V K X7R (0805) ROHS G -- R775 30070785 RES MG SAFE 1/2W 7.8M J NEW ROHS G --
C744 30000341 CAP SMD 68NF 50V K X7R (0805) ROHS G -- R778 30000475 RES SMD 1/10W 10K J 0805 ROHS G --
C745 30000224 CAP SMD 220PF 50V J COG (0805) ROHS G -- R782 30001735 RES SMD 1/8W 0R 1206 ROHS G --
C746 30061026 CAP SMD 1UF 25V K X7R (0805) ROHS G -- R783 30000721 RES SMD 1/10W 4.7K J 0805 ROHS G --
C749 30000294 CAP SMD 100NF 50V K X7R (0805) ROHS G -- R784 30000475 RES SMD 1/10W 10K J 0805 ROHS G --
C750 30000294 CAP SMD 100NF 50V K X7R (0805) ROHS G -- R785 30012852 RES SMD 1/10W 3.9K F 0805 ROHS G --
C755 30052271 CAP SMD 10UF 25V K X5R (1206) ROHS G -- R786 30025823 RES SMD 1/10W 15K F 0805 ROHS G --
C757 30000284 CAP SMD 1NF 50V K X7R (0805) ROHS G -- R787 30000659 RES SMD 1/10W 330R J 0805 ROHS G --
C758 30052271 CAP SMD 10UF 25V K X5R (1206) ROHS G -- R788 30000664 RES SMD 1/10W 3.3K J 0805 ROHS G --
C759 30052271 CAP SMD 10UF 25V K X5R (1206) ROHS G -- R790 30000668 RES SMD 1/10W 33K J 0805 ROHS G --
C762 30052271 CAP SMD 10UF 25V K X5R (1206) ROHS G -- R791 30000475 RES SMD 1/10W 10K J 0805 ROHS G --
C763 30052271 CAP SMD 10UF 25V K X5R (1206) ROHS G -- R792 30000475 RES SMD 1/10W 10K J 0805 ROHS G --
C764 30052271 CAP SMD 10UF 25V K X5R (1206) ROHS G -- R793 30000710 RES SMD 1/10W 47R J 0805 ROHS G --
C765 30052271 CAP SMD 10UF 25V K X5R (1206) ROHS G -- R794 30001734 RES SMD 1/10W 0R 0805 ROHS G --
C766 30070746 CAPEL 470UF 10V M105C 640mA 8X12 SHALEFT G -- R796 30000457 RES SMD 1/10W 10R J 0805 ROHS G --
C767 30000284 CAP SMD 1NF 50V K X7R (0805) ROHS G -- R797 30007026 RES SMD 1/10W 5.1K J 0805 ROHS G --
C769 30052271 CAP SMD 10UF 25V K X5R (1206) ROHS G -- R798 30000751 RES SMD 1/10W 5.6K J 0805 ROHS G --
C770 30052271 CAP SMD 10UF 25V K X5R (1206) ROHS G -- R799 30007021 RES SMD 1/10W 1K F 0805 ROHS G --
C771 30000284 CAP SMD 1NF 50V K X7R (0805) ROHS G -- R800 30000593 RES SMD 1/10W 2.2K J 0805 ROHS G --
C772 30069937 CAP CER SAFE 2.2NF 4KV M 3.5MMSHAROHS G -- R801 30000653 RES SMD 1/10W 33R J 0805 ROHS G --
C773 30069937 CAP CER SAFE 2.2NF 4KV M 3.5MMSHAROHS G -- R802 30000593 RES SMD 1/10W 2.2K J 0805 ROHS G --
C774 30069937 CAP CER SAFE 2.2NF 4KV M 3.5MMSHAROHS G -- R803 30000593 RES SMD 1/10W 2.2K J 0805 ROHS G --
C775 30070745 CAPEL 560UF 50V M105C 1500mA 8X40SHALEFT G -- R804 30000609 RES SMD 1/10W 2.2R J 0805 ROHS G --
C776 30059259 CAP SMD 2.2UF 25V K X7R (0805) ROHS G -- R805 30000609 RES SMD 1/10W 2.2R J 0805 ROHS G --
R806 30064582 RES SMD 1/8W 18K F 0805 ROHS G --
RESISTORS R807 30000475 RES SMD 1/10W 10K J 0805 ROHS G --
R100 30069236 CAP VAR SAFE 510V K JVR14N511K87I40 ROHS G -- R813 30000597 RES SMD 1/10W 22K J 0805 ROHS G --
R706 30046429 RES SMD 1/4W 2M F 1206 ROHS G -- R814 30000609 RES SMD 1/10W 2.2R J 0805 ROHS G --
R707 30046429 RES SMD 1/4W 2M F 1206 ROHS G -- R818 30000668 RES SMD 1/10W 33K J 0805 ROHS G --
R708 30039196 RES SMD 1/4W 1M F 1206 ROHS G -- R819 30000480 RES SMD 1/10W 100K J 0805 ROHS G --
R709 30046429 RES SMD 1/4W 2M F 1206 ROHS G -- R820 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G --
R716 30039196 RES SMD 1/4W 1M F 1206 ROHS G -- R822 30001734 RES SMD 1/10W 0R 0805 ROHS G --

84
LC-22LE240

PRICE PRICE
CODE
REF No. PARTS DESCRIPTION * REF No. PARTS DESCRIPTION * CODE
R824 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G --
J723 30002583 KISA DEVRE TELI 0.6MM G --
R825 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G --
J724 30002583 KISA DEVRE TELI 0.6MM G --
R826 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G --
J725 30002583 KISA DEVRE TELI 0.6MM G --
R827 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G --
R828 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- J726 30001735 RES SMD 1/8W 0R 1206 ROHS G --
R829 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- J728 30002583 KISA DEVRE TELI 0.6MM G --
R830 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- J729 30001734 RES SMD 1/10W 0R 0805 ROHS G --
R831 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- J730 30002583 KISA DEVRE TELI 0.6MM G --
R832 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- P1 35000176 EYELET BR 2*3MM ROHS G --
R833 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- P2 35000176 EYELET BR 2*3MM ROHS G --
R834 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- P3 35000176 EYELET BR 2*3MM ROHS G --
R838 30001734 RES SMD 1/10W 0R 0805 ROHS G --
P4 35000176 EYELET BR 2*3MM ROHS G --
R841 30000631 RES SMD 1/10W 2.7K J 0805 ROHS G --
PL700 30069110 CONN HEADER SAFE 2P V0 7.92MM R/A BLKRHS G --
R842 30000664 RES SMD 1/10W 3.3K J 0805 ROHS G --
R843 30000563 RES SMD 1/10W 1.8K J 0805 ROHS G --
PL701 30067693 CONN HEADER SAFE 2P V0 7.92MM SIDE ROHS G --
R848 30000668 RES SMD 1/10W 33K J 0805 ROHS G -- PL703 30066828 CONN PINHEADER2x10P2.54W/PLASTICSIDEROHS G --
R849 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- PL706 30066919 CONN HEADER 6P 2.0MM SIDE W/LOCK RoHS G --
R850 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- PL707 35016591 GROUND TERMINAL 3.5MM ROHS G --
R851 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- PL708 35016591 GROUND TERMINAL 3.5MM ROHS G --
R852 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- PL709 35016591 GROUND TERMINAL 3.5MM ROHS G --
R853 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- PL710 35016591 GROUND TERMINAL 3.5MM ROHS G --
R854 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G -- S702 30001734 RES SMD 1/10W 0R 0805 ROHS G --
R855 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G --
S705 30001734 RES SMD 1/10W 0R 0805 ROHS G --
R856 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G --
S711 30001734 RES SMD 1/10W 0R 0805 ROHS G --
R857 30013199 RES SMD 1/10W 2.4K F 0805 ROHS G --
R858 30046429 RES SMD 1/4W 2M F 1206 ROHS G --
S733 30001735 RES SMD 1/8W 0R 1206 ROHS G --
R859 30046429 RES SMD 1/4W 2M F 1206 ROHS G -- SP1 40046710 SPACER SUPPORT TCF-12_ ROHS_V0 G --
R860 30046429 RES SMD 1/4W 2M F 1206 ROHS G -- TH701 30067963 RES THE SAFE 10R/2.3A NTC 7mm RAD RoHS G --
R861 30000727 RES SMD 1/10W 47K J 0805 ROHS G -- TR700 30067936 TRF SMT SAFE 17IPS60 EFD33.7 10mm ROHS G --
R862 30000506 RES SMD 1/10W 120K J 0805 ROHS G --

MISCELLANEOUS PARTS
F700 30028356 FUSE SAFE 3.15A 250V (RADIAL) ROHS G --
F701 30028356 FUSE SAFE 3.15A 250V (RADIAL) ROHS G --
J700 30002583 KISA DEVRE TELI 0.6MM G --
J701 30002583 KISA DEVRE TELI 0.6MM G --
J702 30002583 KISA DEVRE TELI 0.6MM G --
J703 30002583 KISA DEVRE TELI 0.6MM G --
J704 30002583 KISA DEVRE TELI 0.6MM G --
J706 30002583 KISA DEVRE TELI 0.6MM G --
J707 30002583 KISA DEVRE TELI 0.6MM G --
J708 30002583 KISA DEVRE TELI 0.6MM G --
J709 30002583 KISA DEVRE TELI 0.6MM G --
J710 30001735 RES SMD 1/8W 0R 1206 ROHS G --
J711 30001735 RES SMD 1/8W 0R 1206 ROHS G --
J712 30002583 KISA DEVRE TELI 0.6MM G --
J713 30002583 KISA DEVRE TELI 0.6MM G --
J714 30002583 KISA DEVRE TELI 0.6MM G --
J715 30002583 KISA DEVRE TELI 0.6MM G --
J716 30002583 KISA DEVRE TELI 0.6MM G --
J717 30002583 KISA DEVRE TELI 0.6MM G --
J718 30002583 KISA DEVRE TELI 0.6MM G --
J719 30002583 KISA DEVRE TELI 0.6MM G --
J720 30002583 KISA DEVRE TELI 0.6MM G --
J721 30001734 RES SMD 1/10W 0R 0805 ROHS G --
J722 30002583 KISA DEVRE TELI 0.6MM G --

85
LC-22LE240

86
CABINET AND MECHANICAL PART LISTING

FRONT 22942 LED(SHARP/S)(V0) 20564620


LED IR LENS TFT XX856 (%3 MILKY) VER5. 40043423
MD.ASY.17LD98-7-19942(MB25(SHA)RED/GR 20565343
LENS COSMETIC 22942 LED (PC-I(V0) 40046771
SPK.AS.22942-LED(R/L)(MB60-6P)(BL(SHA 20569443
TFT 22FHD50HZ ELED LG LC215EUE TEA1 (CN) 30072972
FR_22LED_WO/DVD_MB60_PW80_CON07_LG_ SDA1 45010864
BC.22942L DV 60&G&R WO/D&KL(PCA(I(SH 20564663
ROC.SW.AS.(MB60_22942_SHARP) 20569417
FOOT ASSY 19942(GL-BLK_SHARP) 20596550
LC-22LE240

CABINET AND MECHANICAL


PARTS LISTING
PRICE
REF No. PARTS DESCRIPTION * CODE
20564620 FRONT 22942 LED(SHARP/S)(V0) ( Front Cabinet) G --
20564663 BC.22942L DV 60&G&R&L&L WO/D&KL(PCA(I(SH ( Rear Cabinet) G --
40044553 COVER GROMET 30x30 (I(V0 G --
40046771 LENS COSMETIC 22942 LED (PC-I(V0) ( Decoration on front Cabinet) G --
40043423 LED IR LENS TFT XX856 (%3 MILKY) VER5. G --
45010864 FR_22LED_WO/DVD_MB60_PW80_CON07_LG_ TEA1 (Metal Frame) G --
30071426 CNAS6P/200 SIS W/DC1007#24 pw05-con07SHA (Converter cable) G --
20569417 ROC.SW.AS.(MB60_22942_SHARP) (Rocker Switch & cable) G --
20596550 FOOT ASSY 19942(GL-BLK_SHARP) (Stand Foot) G --
20569443 SPK.AS.22942-LED(R/L)(MB60-6P)(BL(SHA (Speakers) G --
40047983 BRACKET IO MB60S-M2 VER5(I(ABSV0(SHA G --
23036094 CN.A.FFC 30P/300 P=1MM LVDS(22"62-2LGTA1360 (LVDS FFC cable) G --
30070373 CABLE FFC 6P/500 (0.5mm) UL20861 ROHS ( Panel converter Cable) G --

ACCESORIES PARTS LISTING


23003481 ARTWORK SHARP LC-22LE240E ( I/B and Accesories ) G --
23006167 ARTWORK SHARP LC-22LE240RU ( I/B and Accesories ) G --
23006160 ARTWORK SHARP LC-22LE240EV ( I/B and Accesories ) G --
20601206 R/C 1910 SHARP&1910 (GRAY/S)(NEW G --
30070136 PWR CORD SAFE EU 1800-70 W/GR+H 3P ROHS G --

PACKING PART LISTING


50200615 CARTON BOX SHARP LC-22LE240E G --
50201478 CARTON BOX SHARP LC-22LE240RU G --
50201474 CARTON BOX SHARP LC-22LE240EV G --
20563573 SNOW BOX ASSY(T/B)22942 LED (Top,Bottom strafors) G --

87
LC-22LE240 125mm

100mm

80mm

63mm

COPYRIGHT
50mm
© 2011 BY SHARP CORPORATION
ALL RIGHTS RESERVED

No part of this publication may be reproduced,


stored in a retrieval system, or transmitted in any
form
40mm
or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.

31.5mm

25mm

Technical information and Production:


Vestel Electronik AS

20mm

Technical information re-issued

SHARP CORPORATION
AV System Group

SHARP ELECTRONICA ESPAÑA S.A.


Service Manual Group
Engineering Dept.
WTC Almeda Park
Pl. de la Pau s/n (Ed.6 PB)
08940 Cornella de Llobregat
Barcelona
Spain

88

You might also like