Professional Documents
Culture Documents
MS317-18002 (1) (English (American) )
MS317-18002 (1) (English (American) )
MS317-18002 (1) (English (American) )
MS317-18002
GR Window Louvers Installation and
Thank you very much for purchasing GR Window Louvers. Operation Manual
This manual describes the installation and handling procedures and precautions for this
product. Please be sure to read this manual before installation, and be sure to install and
handle the product c o r r e c t l y .
This document must be handed over to the customer.
★ This product cannot be i n s t a l l e d on unregistered vehicles.
■ Components
No. Name of product Item No. quan remarks
tity
(i) window louver 1
(2) Bracket A 6
(iii) Bracket B (RH/LH) each
one
4) bolt 8 M5 x 12
5) washer 8 t3.0×φ5.0×φ18.0
6) Hexagonal wrench (for product 1 3mm
removal)
se PAC
Check that Primer
there is no damage to the main unit and 08867-00220
that all accessories1 are inN-200
order immediately upon arrival.
ve
■nComponent Diagram
(us(i)
(a) (2) (3) (4) (5) (6) (7) (8) (c) (d) (e) (4) (5) (6) (7) (8) (9) (10)
ed
(11) (5) (5)
in
leg
al
do
RH LH
cu
m
⑥en 7) (viii) (ix) (viii) (ix)
ts)
Installation
Instructi
on○○
s ○○
○
patte
Please purch
ase this produ
Thank you very ct
rn
tools used
)
Screwdriver
Spanner
TorxWrenc
h
precaution
sPlease handle with
paper
care.
Not
advice
attention (heed)
Before installing this product, please make sure that the main unit and all its components are complete
and free from damage or defects. We may not be able to respond to claims of damage or defects
discovered after installation.
When installing this product, handle it on a protective sheet to prevent scratches, and at the same time,
protect the installation site with a protective material before installation. Be careful not to scratch or damage
the product during installation.
Degreasing operation (Please also refer to the attached "Degreasing Operation Procedure")
When degreasing, use isopropyl alcohol (IPA) with a clean rag, and never use solvents other than those listed.
Never use body coatings, parts cleaners, brake cleaners, or other solvents for degreasing. They will not
degrease properly and may cause floating or peeling.
About double-sided tape
Failure to degrease the surface will cause the double-sided tape to peel off even if it is adhered.
Once the double-coated adhesive tape is applied and then peeled off, it cannot be reapplied as its
adhesive strength will decrease. The double-coated adhesive tape of this product will lose adhesive
strength significantly when the ambient temperature is lower than 20°C (68°F).
If the temperature is not high enough, the double-sided tape will peel off.
Crimp the double-sided tape securely with 49N (5kgf) or more (to the extent that the vehicle is
lightly shaken). Insufficient crimping will cause the double-sided tape to peel off.
Please do not allow the product to be exposed to car wash, water (including wiping), rain, etc. for 24
hours after installation. Failure to follow the precautions after installation may cause the product to lift
or peel.
After installation is complete.
After installation, make sure that there is no interference between this product and the vehicle.
If the negative terminal of the battery is disconnected during the work, please set and check the system after
No. 2210- 3 /8
the work is completed. Re-setting or adjustment may be required depending on the partsT2730001
disassembled or
removed for this installation.
Check, adjust and set each part according to the repair manual (issued by Toyota Motor Corporation) for the vehicle in
question.
No. 2210- 4 /8
T2730001
■ Table of Contents
1. cover, part number and applicable car model, component parts, component parts
drawing ・・・・・・・・・・・・・・・1
2. installation precautions (for installers) ・・・・・・・・・・・・・・・2
Table of contents, tools, protective equipment and consumables required for installation,
warranty information, installation diagram...3
4. installation preparation and installation
instructions: ・・・・・・・・・・・・・・・・・・・・・・・・・4-8
5. inspection and precautions after installation is
completed: ・・・・・・・・・・・・・・・・・・・・・・・8
6. repair kit double-sided tape application ・・・・・・・・・・・・・・・・・・・・・・8
■ Warranty
This product is warranted for 1 year and 20,000Km (until 1 year
or 20,000Km, whichever comes first). (1 year or 20,000Km,
whichever comes first)
*For warranty details, please visit the TRD parts catalog site <https://www.trdparts.jp/>.
See "Warranty" for more i n f o r m a t i o n .
■ Mounting Configuration
rear window
glass
No. 2210-T2730001 6 /8
5. Attach the ➇" stencils B and D to the rear window glass with masking tape, etc. as shown in Figure 3. (2 places each
on the left and right)
Figu LH illustration: work
re 3. common to both right Rear window glass
superfi and left sides R stop criterion
cial fre
qu
view
LH
en ➇ Pattern B
cy LH
(es ➇ Pattern B
p. LH
of
wa
vef Rear window glass Rear window glass masking tape
or
m R stop criterion
s)
➇ Pattern
Paper D LH
masking tape
hinge
9. Fig.
As 7shown in Figure 7,common
*LH illustration: fit ③Bracket B to ➇Form D and temporarily tighten it with the vehicle bolts removed in step 7.
trunklid
work
(one for both
each rightleft
on the andandleft
right)
sides Bracket B LH
➇ Pattern
Paper D LH
frequency [Cross-
Bracket B
LH
(esp. of sectional
view] Vehicle Bolt
waveforms)
hinge
Vehicle Bolt up
fre
qu fram
en e packing
cy
(es
p.
of
wa
vef
or
m
s)
hinge
CAUTION: Make sure that the packing is attached between the hinge and the car body.
No. 2210- 8 /8
T2730001
10. Check the installation position as shown in
Figure 8, and peel off the release paper of the
double-sided tape in the direction of the arrow
in numerical order while attaching and
crimping the tape. (2 locations each on the left
and right sides)
Figure 9. *LH illustration: common work for both right and left 13. Peel off the release paper of the double-sided
tape of ②Bracket A in the direction of the
sides arrow and attach it to the front side with
masking tape masking tape, etc. as shown in Figure 9. (2
Bracket A places each)
release paper
release paper
15. Peel off the ➇" stencils A, B, C, and D, and wipe off
any primer that protrudes from each bracket with
isopropyl alcohol (IPA).
No. 2210- 9 /8
T2730001
The adhesive strength of the double-sided tape requires 3 to 5 hours to stabilize.
advice After installing the product, please allow at least 3 hours of open time to avoid strong
Fig. 8 *LH illustration: work common to both
vibration or wind pressure (including vehicle movement).
right and left sides
Warning. Double-sided tape must be fully crimped. Insufficient crimping may cause floating, peeling,
Bracket B LH
or other symptoms, which may result in serious problems such as falling off.
1
Do not allow water to splash on the adhesive area due to rain, car wash, etc. within 24 hours after
FR the adhesion of the double-coated adhesive tape. Adhesive strength may deteriorate, causing
the tape to peel off or fall off.
LH
2
➇ Pattern
Paper D LH
➇ Pattern
Paper A LH
(2) Bracket A
Rear window glass
➇ Pattern B
LH
fre
qu
en (2) Bracket A
LHcy
➇ Pattern
(es
p. Paper C LH
of
wa
vef
or
m
s)
No. 2210- 10
T2730001 /8
Window Louver Installation Instructions
1. As shown in Figure 11, align the window louvers (1) with the hole positions of (2) Bracket A and (3) Bracket B,
place them on the rear window glass, and temporarily tighten them with (4) bolts and (5) washers. (4 places each on
Figure 11.
Fastening section (4 locations
on each side)
4) Bolt
(5) Washer