Professional Documents
Culture Documents
ECM Prelude 95 2.2 y 2.3
ECM Prelude 95 2.2 y 2.3
To gain access, lift up the carpet and remove the protective metal panel covering the
ECM.
O R
A D
C U
E
g o
in
See CS/F
o m
D
to
The ECM is self testing.
a n
S
Any faults detected will be:
Specific voltages listed in the following tables are approximate and may vary between
vehicles.
nto
A5 Fuel Injector Control (Cylinder #3)
S
Ignition ON..................................................... a Battery volts
o m
.c
A6 Oxygen Sensor Heater Ground
Ignition ON
o o
a h
y
Heater ON...................................................... < 1.0 volt
@
04 Pump Coil Ground
Heater OFF.................................................... Battery volts
A 7 Main Relay 0
2 or running............................... Low volts
- Fuel
c e
Engine cranking
A 8 Main n
a Relay - Fuel Pump Coil Ground
r mEngine cranking or running............................... < 1.0 volt
Ignition ON
Ignition ON
.c o
Engine running................................................ 0.8 to 2.8 volts
o o
a h
A 17 Variable Intake Manifold Solenoid
y
H22A1 Models
4 @
0 0
e2
Engine running
o rm
r f
pe A 17 Variable Intake Manifold Solenoid
h p H23A1 Models
Engine running
Engine speed < 4800 rpm................................ < 1.0 volt
Engine speed > 4800 rpm................................ Battery volts
o m
.c
A 25 ECM Supply Volts
o
Ignition ON
h o
y a
Main relay energised....................................... Battery volts
A 26 ECM Ground 4
@
Ignition ON0 0
e2
/ OFF............................................ 0 volts
Connector 'B'c
an
o rm
r f
pe
h p Pin # Circuit and Ststus.......................................... Voltage
Ignition ON
B2 ECM Ground
B5 Air Conditioner
Engine running
O R
A/C ON.......................................................... 0 to 10 volts
A D
A/C OFF......................................................... Battery Voltage
C U
B7 Gear Selector Detection E
g o
in
Ignition ON
o o
Steering wheel at rest position.......................... < 1.0 volt
ah
Steering wheel moved from rest position............ Battery volts
y
4 @
B9
0
Cranking Signal
0
2
Engine cranking.............................................. > 8 volts
e
c Sensor
B 10 Vehicle
n Speed
a Vehicle
See Speed Sensor ............................. 0 to 5 volts, or
r m 0 to 12 volts
O R
B 15 Crankshaft Position Sensor
A D
Engine cranking.............................................. AC voltage
C U
Engine at idle.................................................. AC voltage E
g o
in
B 16 Crankshaft Position Sensor
Engine cranking..............................................
o m
AC voltage
Dvoltage
t o
n
Engine at idle.................................................. AC
S a
m
Connector 'C'
.c o
o o
a h
y
4 @
Pin # Circuit and Status......................................... Voltage
0 0 Supply Voltage
2 / OFF............................................ Battery volts
C1 ECM Permanent
c e
Ignition ON
C2 n
a Light
Brake Signal
o rmIgnition ON
r f
pe Brake pedal depressed.................................... Battery volts
C3 Knock Sensor
See Knock Sensor ......................................... voltage varies
C4 Diagnostic Connector /
Fault Code Enable Connector
Ignition ON
o o
Throttle plate at rest position............................ 0.5 volts
y ah
Throttle plate fully open.................................... 4.5 volts
4 @
C 12
0
EGR Position Sensor Output Signal
0
Engine running 2
c e
EGR valveanopen............................................... 4.3 volts
r mEGR valve closed............................................ 1.2 volts
r fo
pe
h p C 13 Engine Coolant Temperature Sensor Signal
Ignition ON
Ignition ON
.c o
Ignition ON / OFF............................................ 0 volts
C 22 Sensor Ground
o o
y ah
Ignition ON / OFF............................................ 0 volts
4 @
00
e2
c
an
r m
fr o
p e
h p