Professional Documents
Culture Documents
JT701D Maintenance GuideV1.0
JT701D Maintenance GuideV1.0
JT701D Maintenance GuideV1.0
V1.0
Introduction
This maintaining guide manual the structure function, PCBA function, common fault description and
troubleshooting of JT701D.
1 / 15
No. Function Description
1 RFID card swiping slot Swipe authorized RFID card to unlock the device
2 The unit working LED status GPS signal , GSM signal, LVS-low battery, CHG-charging indication
3 Charging slot External charging slot, input voltage range-DC 5-12V 2A
4 Air Evacuation Window The pressure difference generated at high and low temperatures is
equalized through this window
5 PRG procedure upgrading This interface is a dedicated engineering interface, can be upgraded
/configuration and configure the device parameters
6 USB Charge/Configuration This interface is USB Micro type, which can charge and configure the
unit
7 Power switch It can switch off the power of the unit
8 1st Sim card The primary sim card
9 2nd sim card The secondary sim card
10 Photosensitive detection It is the back cover photosensitive detection switch, the alarm will be
generated when the back cover is open
11 The small lock column By connecting with the motor slider assembly structure component,
component which can control the small cable head to switch the lock/unlock of the
unit.
12 Motor component Which include built-in GPS antenna, motor, slider, the main functions
of this part is receiving GPS signal and powering lock /unlock status
13 The big lock column By connecting with the motor slider assembly structure component,
component which can control the small cable head to switch the lock/unlock of the
unit.
2 / 15
14 RFID circuit Non-contact IC card RF reader coil(125Khz)
18 Lock rope detection shrapnel Detect if the lock rope insert and rope cutting alarm
19 Slider limit detection Motor operation reset detection
component
20 Wire rope assembly Connect to the two keyholes of the device to lock the wire rope
3 / 15
Circuit Function Description
21
29
30 22
24
27
26
31
25 28
4 / 15
33 29
23
35 34
36
6 / 15
Routine Fault Problems and Troubleshooting Methods
No. Problems Description Troubleshooting Fault
Methods Location
1 Device run well, motor 1. J28 wire loose 23、17
responds to RFID card 2. Check Q7, R55, R47 and buzzer. Swiping RFID card,
swiping, but buzzer SCM send out a high level to R55, Q7 breakover to drive
does not ring buzzer ring through R47.
2 Cannot charge 1. In case of charging light blinking quickly, the battery 15、33、3
circuit is open
2. In case that charging light does not bright, check power
supply input polarity and output voltage.
3. In case that charging light does not bright, check
Q13, Q8, L3, R27 and U5
4. Check if the nut of external input charging port and
connection strap loose or not
3 Cannot locate 1. Check leg 7 and leg 8 of M1 module power voltage 3.3V, 12、25
leg2, leg 3 and leg 11 power voltage 3.2V
2. GPS antenna module issue, the weak receiving signal
can lead to non-locating. Change a new GPS antenna
module for a try.
3. Check the circuit surrounding GPS antenna module
4 Cannot connect 1. U11 rosin joint, use heat dryer blow welding 16、29、35
internet 2. Observe if SIM card slot is dirty and deformed, if the
splinter connect well.
3. Check GSM module M3 rosin joint or not
4. Check GSM module M3’s power supply
5. Check GSM antenna connection and damage or not.
5 Motor does not 1. Check if battery power is enough or not 12、15、22、
respond 2. Check J24 two loops resistance is more or less 22Ω or 32
not, more or less 22Ω means OK.
3. If one loop is short, motor loop break GPS antenna
module wire, it can lead to motor no response.
Disentangling GPS antenna module wire will be OK.
4. Device run well (GSM light flashing, GPS light flashing,
buzzer ring in case of RFID card swiping), check J22 wire
loose or not or check the components surrounding U12
motor driving chipset. Check R70 and R71 are damaged or
7 / 15
not. In case of RFID card swiping, if 15 leg of US12 voltage
is less than 12V, there is some issue on R45, Q10 and
Q11, if 22 leg and 28 leg are less than 12V, there is some
issue on U13, Q9, L5, r66, R63-R65 and D7.
6 GSM light, GPS light, 1. J28 wire loose. 17、23
CHG light and STB 2. R7, R8, R14, R34 and R37 resistance are break.
light do not bright
7 USB cannot be 1. USB port loose, connection not well. 26、34
recognized. 2. The wire from USB port to R11, R13, R6 and R17 are
break.
8 Device cannot be 1. J17 connection not well, check R19、R16、R5、C7、R4 26、34
upgraded. 2. Check MCU power supply
9 Device run well, but 1. Wire loop is open (the normal is 6Ω). 14、28、31
RFID card cannot be 2. RFID chipset and surrounding components are
swiped. damaged
10 Device run not well 1. U11 rosin joint, use heat dryer blow welding 27、35
(GSM light and GPS 2. X1 crystal oscillator and X2 crystal oscillator are broken.
light blink at same time)
11 There is power in The open circuit in SWI get faulty 24、27、34
battery, but device R15,Q4 get faulty, the 3.3V power not available
don’t work X1 and X2 Crystal Oscillator failed, the Chip don’t work.
12 The steel string cannot 1.Check if the lock parts deformed in mechanically, or 11、12、13
be pulled out, or cannot something inside caused the problem
be locked tightly 2.Check if the parts in slide rail deformed
3.Check the motor circuit
13 The device don’t act 1.Check if the lock parts deformed in mechanically, or 12、15、18、
when plug the lock something inside caused the problem 20、22
string Check if the parts in slide rail deformed
Check the motor circuit
Or the lock string not conductive
9 / 15
10 / 15
11 / 15
12 / 15
13 / 15
14 / 15
15 / 15