Professional Documents
Culture Documents
Sla 3 e 100
Sla 3 e 100
Short description
Data and energy: munication on the yellow AS-Interface cable. Participants with an infra-
The primary switched mode DIN rail power supply SLA3.100 specifically red interface can then quickly be assigned a new ID address by means of
supplies AS Interface® systems with energy. The AS-Interface bus techno- an infrared programming unit without the need to disconnect them
logy allows to connect up to 62 participants to a control and to supply from the AS-Interface cable. Afterwards, the "Communication Mode"
them with energy with a single two-conductor cable. When connecting can be selected again to re-start the data communication.
slaves, the yellow AS-Interface cable offers the high degree of protection Fit for the world market:
IP67 in conjunction with the insulation displacement. The communica- The input voltage range of the unit can be selected on the front panel.
tion signals of the individual network participants are modulated onto Thus, it can be operated worldwide on all usual single-phase line volta-
the supply voltage. For this purpose, specific power supply units with in- ges. International (IEC 60950) and various national (CBscheme) approvals
tegrated data decoupling are required for AS-Interface systems. allow for worldwide application.
Fast addressing of slaves:
The "IR addressing mode" selectable via jumper interrupts the data com-
Input Output
Rated voltage AC100-120/220-240V Rated voltage DC 30.55V ±3% (not adjustable)
(selectable by front panel slide switch) Rated current 2.8A
Rated current 2.0A (switch in 115V position)
Isolation Safe low voltage PELV (IEC364-4-41)
0.9A (switch in 230V position) SELV (IEC60950)
Frequency 47...63 Hz (alternatively DC also possible)
Current limitation >3.2 A
Voltage range AC 85...132V/184...264V, DC 230...375V
Overload behaviour Continuous current (also see diagram)
Power factor >0.5 Short-circuit current min. 3.2A, max. 4.6A
Harmonic current EN 61000-3-2 [PFC], Class A limits are fulfilled
Load regulation stat. <200mV (no load / full load)
emissions
Line regulation stat. <10mV (AC 85...132V/184...264V)
Integrated internal T2A5 / 250V HBC (not accessible)
fuse Ripple <50 mVPP (500kHz bandw., 50Ω measurem.,
ohmic load)
Inrush current limited by NTC resistor
Tamb = +50°C, cold start (line impedance Noise (Spikes) <100mVPP (20MHz bandw., 50Ω measurem.,
acc. EN 61000-3-3) ohmic load)
Peak current Ipk 20A (AC 132V) / 38A (AC 264V) Over-voltage protection max. 55V
I2t 1.5 A2s (AC 132V) / 1.8 A2s (AC 264V)
Operating indictor Green LED (extinguishes at overload)
Hold-up time >26 ms @ AC 100V or 196V and rated load
Output is protected against short-circuit, open circuit and overload.
(also see diagram)
Use AS-Interface power supplies only together with AS-Interface lines.
Order information
Order number Description
SLA3.100 AS-Interface power supply unit
SLZ11 Adapter for S7-300 rail
SLZ02 Wall mounting set (two pcs. per package)
sla3e100 / 040511 1/4
Data sheet SLA3.100
Schematic
Mode Selector:
Communication/
IR Addressing
AS-i +
L DC
AS-i +
V
DC
N Shield
Transient- Input Rectifier AS-i
AS-Interface Infrared (IR) AS-i -
Inrush- and and Hold-up DC to DC Decoupling Addressing AS-i -
EMC- Filter Capacitor Converter Network Mode
IR on
AS-i ok
Plug-in jumper:
Pos. 1-2: regular AS-
Interface communication
Pos. 2-3: Data communi-
cation is interrupted.
IR-addressing can be car-
ried out
Red LED:
DIN-rail mouting bracket ON: Jumper position 2-3
OFF: Jumper position 1-2
115/230V switch:
Slide switch to select the
input voltage range
Input terminals
blue Negative AS-Interface output voltage (twice) Operation without AS-Interface: This AS-Interface PSU has an in-
ductive output. When operating without AS-Interface structure (e.g. in
Shield Connection of machine ground. a laboratory test) you should connect a 470µF / 35V capacitor between
(Functional earth for balancing the AS-Inter- AS-Interface + and AS-Interface – as commercial electronic loads in
face output. Connection is recommended for combination with the data decoupling often tend to oscillate, and the
EMC) oscillation may exceed the permitted modulation voltage. Otherwise,
equipment may be destroyed.
Functional diagrams
UOut
115 V
position
150
min.
typ.
130
110
load
115V 230V
switch pos. switch pos.
90 min.
50%
70
50
d
oa
ll l
30
fu
230 V
position
UIn 10
70 95 120 145 170 195 220 245 270
151 Vac
160 Vac
78 Vac
82 Vac
32
28
Efficiency / Power dissipation
95 10 20
16
[W]
90 8
12
loss
8
Efficiency [%]
Power dissipation P
85 6
4
80 4
0
Efficiency 0 1 2 3 4
75 2 Output current Iout [A]
Power dissipation
70 0
0,4 0,7 1 1,3 1,6 1,9 2,2 2,5 2,8 3,1
Output current Iout [A] Derating
Imax (Pmax)
2.8A
(85W)
2.1A
(65W)
Tamb
-10°C
0°C
10°C
20°C
30°C
40°C
50°C
60°C
70°C
Unless otherwise stated, specifications are valid for AC 230V input voltage, +25°C ambient temperature, and 5 min. run-in time. They are subject to change without prior notice.
European Bayerns Best 50
Your partner in power supply: Power Supply Czech 100 Best
Manufacturers Europe’s 500
Association
PULS GmbH
Arabellastraße 15
D-81925 München
Tel.: +49 89 9278-0
Fax: +49 89 9278-199
www.puls-power.com