Professional Documents
Culture Documents
Tx1000ec220-Ec024-V2me-V2e Technical Catalog Ecv2 - VN0121
Tx1000ec220-Ec024-V2me-V2e Technical Catalog Ecv2 - VN0121
VALVE CONTROL : Thermostat acquires the room temperature via its integrated the time area will be flashing, press to select minutes, hours or week,
sensor and maintains the set-point by ON-OFF/modulating output. then press or to adjust the relevant time, press to confirm.
CAPACITIVE TOUCH SERIES
POWER ON OR OFF : TO SELECT MANUAL AND PROGRAMMABLE : In the thermostat ON status, Press
MODEL status. and hold and for more than 5 seconds, the icon of or will be flashing,
INCREASE / DECREASE : In the ON state, press UP or DOWN to increase or press to select manual or programmable and press to confirm.
TX1000EC220-V2 TX1000EC024-V2
decrease the setting parameters.
ADJUSTING OF WEEKLY PROGRAMMABLE : After selected programmable mode,
TX1000EC220-V2M TX1000EC024-V2M HEAT/COOL/VENT : Pressing the MODE button to select heat cool or press for more than 5 seconds enter into program schedule setting then press
ventilation mode. to select setting item of periods, time and temp. Press or to adjust the
APPLICATIONS TEMPERATURE DISPLAY : Temperature display mode can be changed via ISU mode relevant value, press to confirm. The program schedule is a weekly (7days) cycle,
the temperature display mode available for set-point display only, room temperature display it can be selected for 5+2 days, 6+1 days or 7 days. 5+2 is 5 workdays plus 2 days
TX1000 Series is touch pad thermostat with many variants suitable for only, and both room temperature and set-point are displayed. Default is both room temperature holiday a week, 6+1 is for 6 workdays plus 1 day holiday a week, 7 is for 7 workdays
and set-point are displayed.
2-pipe cooling & heating fan coil units and EC motor units. Available in a week. There’s 6 periods for workdays and 2 periods for holidays.
FAN OPERATION : Fan operation available for manual mode and automatic
basic standalone and Modbus communication variants. 3-speed mode and the fan control types can be configured as Ao = Automatic Setting sequence when enter program setting
fan only, CO = Constant (Manual) fan only, BO= Both auto &manual in ISU code #3 Workdays 1st period time adjusting -> temperature adjusting -> 2nd period time
SPECIFICATION In Automatic 3-Speed mode : The fan will be switched upon the differences between adjusting -> temperature adjusting……6th period time adjusting -> temperature
adjusting -> holidays 1st period time adjusting -> temperature adjusting -> 2nd
♦ Power Supply: 85-240VAC / 24VAC• Frequency: 50~60Hz room temperature and the set-point as per following logic :
period time adjusting -> temperature adjusting
In the Cooling Mode :
♦ Function: Cooling/Heating, Valve Control : When the room temperature is 2.5˚C/5˚F higher than set point, the fan will be switched to Auto high. Note : 1. The single period can be switched off by turning off the temperature setting
ON-OFF output for 220VAC and 0-10VDC Modulating for 24VAC When the room temperature is 1.5˚C/3˚F higher than set-point, the fan will be switched to Auto medium.
by pressing POWER button, Modbus 40005 will show 00260.
2. The time adjusting 1-6 periods of working days & 1-2 periods of holiday should be
♦ Relay Life: 220±10% VAC, 3(5)A, 100,000 times When the room temperature is 1 ˚C/1˚F higher than set-point, the fan will be switched to Auto low.
moved like clockwise (counterclockwise setting is not available, Example : 00:00 am
♦ Wiring Max: 16AWG In the Heating Mode : is not available on 6th period )
When the room temperature is 2.5˚C/5˚F lower than set point, the fan will be switched to Auto high. 3. In the weekly programmable setting, the parameters of cooling mode and heating
♦ Sensing Element: 10K(@25°C) NTC When the room temperature is 1.5˚C/3˚F lower than set-point, the fan will be switched to Auto medium. mode can be set seperately. If the thermostat enters into programmable mode in
♦ Display Accuracy: 0.5°C, Set-point accuracy: 0.5°C/step When the room temperature is 1 ˚C/1˚F lower than set-point, the fan will be switched to Auto low. cooling mode states, the period time and temperature are set for cooling mode.
Deadzone temperature is 0.5˚C / 1 ˚F
If the thermostat enters into programmable mode in heating mode states, the period
♦ Set-point range: 10-32°C(50-90°F) • Display range: 0-50°C time and temperature are set for heating mode.
If ISU code #3 is set to AO ( Automatic mode only ),the fan speed will be switched upon the differences 4. If the Energy saving mode is activated during programmable mode by button press
♦ Protection Glass: IP 20 • Operation Temperature: -18~49°C of room temperature &setpoint only,it can not change the fan speed by pressing FAN button. , the thermostat will keep running as per the energy saving mode settings, press POWER
♦ Shipping Temperature: -35~65°C • Suitable System: 2-pipe If ISU code #3 is set to CO (Manual mode only ) , the fan can be switched to the selected button to stop energy saving mode.
FCU cooling&heating, ON-OFF/Modulating speed via control output Fh,Fm, FI by pressing FAN button.
If ISU code #3 is set BO (both Manual and automatic mode), the fan can be switched to manual
♦ Suitable Valve: 2-line/3-line valve • Relative Humidity: 10~90% FRI FRI
high, medium and low speed or automatic 3-speed by pressing FAN button.
♦ Installed on 75mm x 75mm box TEMPORARY MODE : When thermostat is working under program schedule, the set-point
can be changed by pressing UP or DOWN buttons. will be displayed.
LCD DISPLAY & KEYS DESCRIPTION The different applications include cool only, heat only and manual heat/cool changeover.
The temporary mode will not be stopped until next period starts.
Rea l Time C l ock Cooling Heating & Ventilation ADJUSTING OF WEEKLY ADJUSTING OF WEEKLY
KEY LOCK : The default status of “Key lock” is all buttons available and it can be changed PROGRAMMABLE IN COOLING MODE PROGRAMMABLE IN HEATING MODE
in ISU mode. Key lock function includes the following settings: All buttons are available PERIODS SYMPOLS DEFAULT TIME
DEFAULT TEMP. DEFAULT TEMP.
COOLING MODE HEATING MODE SYMPOLS DESCRIPTION
(Default) Mode button is locked out. Fan and Mode button are locked out. All buttons
are locked. 1 06:00AM 26 C 18 C 1 ST PERIOD, WAKE UP
2 08:00AM 26 C 18 C 2 ND PERIOD , LEAVE
Weekdays FRI Periods ENERGY SAVING MODE : A dry contact(such as hotel key card) or button press(By WORKDAYS 3 11:30AM 26 C 18 C 3 RD PERIOD,
Room Temp. Program/Manual Mode pressing MODE button for 3 seconds can activate the energy saving mode with
Key lock 4 12:30PM 26 C 18 C BACK FOR LUNCH
Set Temp. icon appearing on the screen). The dry contact can be selected as normal open or
normal close in ISU code#5. 5 17:00PM 26 C 18 C 4 TH PERIOD, LEAVE
Key Card Valve Open/Modbus ID If activated by dry contact, all buttons will be locked except the multi-key for ISU, if 6 22:00PM 26 C 18 C 5 TH PERIOD,
Fan Speed activated by button press, press POWER button can stop energy saving mode. 1 08:00AM 26 C 18 C BACK FOR DINNER
If energy saving mode is activated, the set-point will be changed to remote setback WEEKEND
2 23:00PM 26 C 18 C 6 TH PERIOD, SLEEP
heating set-point and cooling set-point in ISU code#8&9 or via remote BMS Modbus
points. For heating mode, the range of remote setback heating set-point is from 10˚C IN PROGRAMMABLE MODE, SET -POINT PERIODS
to 21 ˚C and default value is 18˚C .The value can be changed with step of 0.5 ˚C. AND TIME COULD BE ADJUSTED DESCRIPTION
Mode Fan Power Up Down
For cooling mode, the range of remote setback cooling set-point is from 22 ˚C to 32 ˚C
SETUP FUNCTION SETTINGS AND OPTIONS
FUNCTION and default value is 26 ˚C. The value can be changed with step of 0.5 ˚C.
The memory function will not keep energy saving mode, when thermostat power cut-off a. Press and key for 5 seconds to enter ISU setting mode, the ISU code will
7 Days 6 Periods and re-powered on, the energy saving mode will be cancelled. be flashing.
2-pipe FCU cooling&heating,
ON-OFF/0-10VDC Modulating Programmable Function FREEZE PROTECTION MODE: Freeze protection can be disable(default) or enabled b. Press or to select the setting items from 1 - 31
Key Pad Lock via ISU mode. If freeze protection is enabled (it is not available in cooling only c. Press and the values of selected item will be flashing with icon on,
3 Speed Fan + Auto Fan Control application) and thermostat is in OFF mode while the room temperature is below 6 Press and revise the values of the setting items, press to confirm.
Both Room temperature and °C , the thermostat will open heating device until the temperature rises to 8 °C.
Energy Saving Mode and Comfort If you want to revise the other setting items, please repeat above step b. and c. while
set-point are displayed RS-485 ID SETTING : When ISU mode code #10 is set to ON, in the thermostat OFF
Mode Settings (Temperature display mode status, press MODE and DOWN together for 5 seconds, the ID number will setting, press to exit, the setting items and values are as below form shown.
can be changed via ISU) be flashing, you can press UP or DOWN to adjust the ID range from 1-64.
ECV2_VN0121
ISU OF: USER SETTING WILL BE KEPT, BUT ONCE RE-ELECTRIFIED NO TERMINALS DESCRIPTION
DESCRIPTION POSSIBLE OPTIONS THE THERMOSTAT WILL BE IN OFF STATES AND WHEN THE
CODE
THERMOSTAT TURNS ON AGAIN, IT WILL RUN AS PER THE L
SETTINGS BEFORE POWER CUT-OFF. 1 LIVE LINE IN
0 HEAT + VENTILATION CHANGEOVER ON/OFF MEMORY
19 SU: USER SETTING WILL BE KEPT, ONCE RE-ELECTRIFIED,
1 SYSTEM TYPE 1 COOL + VENTILATION CHANGEOVER SETTING THE THERMOSTAT WILL BE RUN AS PER THE STATES BEFORE 2
2 TWO PIPES 1H1C (HEAT,COOL&VENTILATION POWER CUT-OFF (DEFAULT IS SU)
3 AO ANALOG OUTPUT 0-10V FOR FAN
CHANGEOVER) DEFAULT 2 10-60 SECONDS(DEFAULT 30 SEC.,USER CAN ADJUST
20 BACK-LIGHT SETTINGS
F : °F B ACK-LIGHT TIME ACCORDING TO ACTUALDEMANDS) 4
2 TEMPERATURE UNIT C : ° C(DEFAULT) ON: ON, THE VALVE OPEN VALUE WILL BE DISPLAYED ON LCD 5 NO VALVE OPEN
AO : AUTO ONLY VALVE OPEN (ONLY AVAILABLE FOR MODULATING TYPE THERMOSTAT)
21 6 NC VALVE CLOSE
3 FAN CONTROL TYPE CO : CONSTANT(MANUAL) ONLY PERCENTAGE OF: OFF, THE VALVE OPEN VALUE WILL NOT BE DISPLAYED
BO : BOTH(DEFAULT) ON THE LCD, DEFAULT IS OF 7 N NEUTRAL LINE IN
22 LOW SPEED FAN SETTINGS SETTING RANGE: 0.5V-3V (O.5V PER STEP), DEFAULT IS 2V
0: ALL BUTTON S ARE AVAILABLE (DEFAULT)
1 : MODE BUTTON IS LOCKED OUT 23 MEDIUM SPEED FAN SETTINGS SETTING RANGE: 3.5V-7V(0.5V PER STEP), DEFAULT IS 5V 8 COM COM FOR UI
4 KEYPAD LOCK OUT 2: FAN AND MODE BUTTONS ARE LOCKED OUT
24 HIGH SPEED FAN SETTINGS SETTING RANGE: 7.5V-10V(0.5V PER STEP), DEFAULT IS 10V
3: ALL BUTTONS ARE LOCKED 9 UI RS (EXTERNAL SENSOR)&KC(KEY CARD)
NO : HOTEL CARD NO
480=4800, 960=9600, 192=19200, 384=38400,
BAUD RATE 576=57600, 115=115200 (DEFAULT:960)
REMOTE SETBACK 25 SELECTION
5 NC : HOTEL CARD NC AFTER CHANGED THE BAUD RATE, PLEASE CUT-OFF POWER AC24V
ENABLE METHOD AC24V
BU : BUTTON (DEFAULT) AND RE-ELECTRIFIED THE THERMOSTAT
OF : DISABLED(DEFAULT) 0 : NO PARITY, DATA 8 BITS, 1 STOP BITS (DEFAULT)
6 FREEZE PROTECTION
ON : ENABLED 1 : NO PARITY, DATA 8 BITS, 2 STOP BITS 0-10V
0-10V
Fan
Fan
RANGE : -9°C~+9°C (-9°F~+9°F) DEFAULT IS 0°C/0°F RS-485 COMMUNICATION 2 : EVEN PARITY, DATA 8 BITS, 1 STOP BITS 0-10V
9
REMOTE SETBACK RANGE 22-32°C DEFAULT IS 26 ° C (RANGE 72-90°F 28 HEATING RANGE STOP 10-32℃,DEFAULT 32℃(50-90℉Default 90℉)
COOLING SET-POINT DEFAULT IS 79°F) 29 COOLING RANGE STOP 10-32℃,DEFAULT 10℃(50-90℉Default 50℉)
MODBUS ID DISPLAY OF: NO MODBUS ID ADDRESS DISPLAY, ON: DISPLAY 0 : DIS PLAY ROOM TEMPERATURE(WHEN PRESSING
10 Rs485
Rs485
SETTING WITH MODBUS ID ADDRESS, DEFAULT IS OF UP OR DOWN BUTTON, IT WILL DISPLAY SET-POINT A:Red
A:Red
B: Black
WITH ICON , WHEN NO KEY PRESS, IT WILL DISPLAY B: Black
RANGE: 1-20 FOR PROPORTIONAL OUTPUT
ROOM TEMP. WITH ICON
11 P: ADJUSTMENT OF ADJUSTMENT, IT SHOULD BE ADJUSTED BASES TEMPERATURE
VALVE CONTROL 30 1 : DISPLAY SET-POINT WITH ICON IN COOLING& TX1000EC024-V2M TX1000EC024-V2
ON THE ACTUAL CONDITION, DEFAULT IS 10 DISPLAY MODE
HEATING MODE (IN PROGRAM MODE, IF PERIOD IS SET
RANGE: 1-100 FOR INTEGRAL OUTPUT ADJUSTMENT,
TO OFF, IT WILL DISPLAY ROOM TEMP INSTEARD), IN
I : ADJUSTMENT OF VENTILATION MODE IT WILL DISPLAY ROOM TEMP WITH ICON
12 IT SHOULD BE ADJUSTED BASES ON THE ACTUAL 2 : DISPLAY BOTH(DEFAULT 2)
VALVE CONTROL
CONDITION, DEFAULT IS 60 THIS FUNCTION IS RESETTING ALL ISU SETTINGS TO FACTORY
IN : INTERNAL SENSOR, OU: EXTERNAL SENSOR, 31 DEFAULTS, OPERATION: PRESS “ ” 0>1>2>3>4, THEN PRESS NO TERMINALS DESCRIPTION
RESET TO DEFAULTS
IF CHOOSING EXTERNAL SENSOR, THE HOTEL KEY CARD “ ”4>3>2 AND PRESS “ ” TO CONFIRM DEFAULT: 0
13 SENSOR SELECTION 1 R 24V ACTIVE
FUNCTION WILL NOT BE AVAILABLE, DEFAULT IS IN IN PROGRAM MODE, WHEN THE PERIOD IS OFF, IT WILL
DISPLAY ROOM TEMP INSTEAD OF SET-POINT.
14 BEE SOUND SETTING ON: ON, OF: OFF, DEFAULT IS OF 2 C 24V NEUTRAL&COM FOR AO
ECV2_VN0121