Professional Documents
Culture Documents
Chapter 8 - Self Test
Chapter 8 - Self Test
Nonisothermal reactions
NOTE: It will be very beneficial to answering the following questions if you first go through the
.
1. The elementary isomerization of A to B was carried out in a packed bed reactor. The following profiles were obtained
Click on the correct true (T) or false (F) answer for this system.
(a) The above profiles could represent an adiabatic system where the addition of inerts to the feed stream will increase conversion. T
or F
If inerts were to be added to the system, sketch the exit conversion as a function of the ratio of entering flow rate of inerts to the entering
flow rate of A, i.e.
Answer
(b) If the reaction is irreversible, a small decrease in the flow rate will produce a small increase in the conversion. T or F
(c) If the reaction is reversible, a small decrease in the flow rate will produce a small increase in the conversion. T or F
takes place in a packed bed reactor. The following profiles were obtained.
Click on the correct true (T) or false (F) answer for this system.
(a) The above profiles could represent an adiabatic system where the addition of inerts will increase the conversion. T or F
If inerts were to be added to the system, sketch the exit conversion as a function of the ratio
Answer
(b) The above profiles could represent a system where decreasing the flow rate will increase the conversion. T or F
(c) The above profiles could represent a system where if the feed temperature is increased, one cannot tell from the above profiles
whether or not the conversion will increase or decrease. T or F
3. The following conversion profiles were measured in two PFR's (A and B) for the same reaction
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 1 of 44
:
(a) Is the reaction exothermic or endothermic?
(d) For reactor A, sketch the conversion profiles for an entering temperature of 300 K and 1000 K and explain.Answer
(e) For reactor A, sketch the exit conversion as a function of inlet feed temperature To. What do you conclude from your plot?
Answer
(f) Discuss each of the regions 1, 2, and 3 in the figure for reactor B.Answer
(a) Sketch the corresponding equilibrium conversion, Xe and conversion profile assuming the reaction is reversible. Answer
(b) On the above temperature versus catalyst weight plot, sketch the temperature profiles if the feed rate were to be decreased by a factor
of 3. Answer
Below are the temperature, equilibrium conversion, Xe, and conversion profiles for an exothermic, reversible reaction in a PBR.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 2 of 44
:
The above profiles are for the PBR with Heat Exchange which comes directly above from this self-test or lecture or . Answer
5. The elementary isomerization of A to B was carried out adiabatically in a packed bed reactor. The following profiles were obtained when
pure A was fed to the reactor
1) The above profiles could represent an adiabatic system where the addition of inerts to the feed stream will increase the conversion.
2) If the reaction is irreversible a small decrease in the flow rate will produce a moderate increase in the conversion.
3) If the reaction is reversible a small decrease in the flow rate will produce a moderate increase in the conversion.
Answer
6) The elementary isomerization of A to B was carried out in a packed bed reactor. The following profiles were obtained when pure A was
fed to the reactor
An
1. increase in the feed temperature will increase the conversion.
A
2.decrease in feed temperature will increase the conversion.
3. There could be a very very very large heat exchanger attached to the reactor with the heat flow given by
Answer
7. The elementary, gas phase, isomerization of A to B was carried out in a packed bed reactor. The following profiles were obtained when
pure A was fed to the reactor.
Inerts were added to a reactor system while T0, P0, and n0 were kept constant. Which of the following figures the exit conversion is as a
function of the qI is correct? i.e. qI (qI = FI0/FA0)
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 3 of 44
:
Note: ? ? ? represents isothermal conversion for a reactor with 10 kg catalyst.
Answer
takes place in a packed bed reactor. The following profiles were obtained
1. The above profiles could represent an adiabatic system where the addition of a small to moderate amount of inerts will increase the
conversion.
2. The above profiles could represent an adiabatic system where decreasing the flow rate will increase the conversion.
3. The above profiles could represent an adiabatic system where if the feed temperature is increased, one cannot tell from the above
profiles whether or not the conversion will increase or decrease.
4. There could be a heat exchanger on the reactor for which the heat flow is
Answer
9. The following conversion profiles were measured in two PFRs, (A and B) for the same reaction
The
A. reaction is exothermic and reversible.
The
B. reaction is exothermic and irreversible.
The
C. reaction is endothermic and irreversible.
The
D. reaction is endothermic and reversible.
Cannot
E. tell for sure if any, some, or all the above are true.
Answer
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 4 of 44
:
10. The exit conversion from an adiabatic PFR is shown below as a function of θI for constant ν0, T0 and P0
The
1. reaction could be a second order endothermic reaction.
The
2. reaction could be a second order exothermic reaction.
The
3. reaction could be a first order exothermic reaction.
The
4. reaction could be a first order endothermic reaction.
The
5. reaction could be an irreversible zero order exothermic reaction.
Answer
11. The exit conversion from an adiabatic PFR is shown below as a function of θI for constant ν0, T0 and P0
Answer
12. The exit conversion from an adiabatic PFR is shown below as a function of θI for constant ν0, T0 and P0
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 5 of 44
:
Which of the following statements is false?
Answer
1. The reaction could be first order endothermic and carried out adiabatically.
2. The reaction is first order endothermic and reactor is heated along the length with Ta being constant.
3. The reaction is second order exothermic and cooled along the length of the reactor with Ta being constant.
Answer
2. The reaction is first order endothermic and reactor is heated along the length with Ta being constant.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 6 of 44
:
3. The reaction is second order exothermic and cooled along the length of the reactor with Ta being constant.
Answer
A. The reaction could be first order endothermic and carried out adiabatically.
B. The reaction could be first order endothermic and reactor is heated along the length with Ta being constant.
C. The reaction could be second order exothermic and cooled along the length of the reactor with Ta being constant.
D. The reaction could be second order exothermic and carried out adiabatically.
E. The reaction could be first order endothermic with very high heating rate.
Answer
1. The reaction could be first order endothermic and carried out adiabatically.
2. The reaction could be could be first order endothermic and reactor is heated along the length with Ta being constant.
3. The reaction could be second order exothermic and cooled along the length of the reactor with Ta being constant.
4. The reaction could be second order exothermic and carried out adiabatically.
Answer
17. The equilibrium conversion and temperature are shown below as a function of catalyst weight for three sets of conditions
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 7 of 44
:
1. The figures could correspond to an exothermic reversible reaction with too high of a cooling rate.
2. The figures could correspond to an exothermic irreversible reaction with too high of a cooling rate.
3. The figures could correspond to an endothermic reversible reaction with too high of a heating rate.
4. The figures could correspond to an endothermic irreversible reaction with too high of a heating rate.
Answer
18. The conversion from an adiabatic PFR is shown below as a function of temperature
90%
A. conversion could be achieved for a first order reaction by increasing the inerts by a factor of 100 or greater for entering
temperature of 700 K.
90%
B. conversion could be achieved for a second order reaction by adding a very large heat exchanger with a very large area for
an entering temperature of 700 K.
For
C. a small but fixed reactor length, one is more likely to get close to the adiabatic equilibrium conversion for an entering
temperature of 500 K than an entering temperature of 900 K.
The
D. reaction could be a second order endothermic reaction carried out with a very large heat exchanger attached to the reactor.
If
E.the reaction is carried out adiabatically, the temperature in a CSTR will drop more for an entering temperature of 900 K then
that for an entering temperature of 500 K.
Answer
19.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 8 of 44
:
1. The above reaction could be exothermic.
Answer
20.
Answer
21.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 9 of 44
:
1. The above reaction could be adiabatic.
Answer
22.
Answer
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 10 of 44
:
Solutions
Problem 1
1 (a) TRUE. If it is an adiabatic system, then it has to be endothermic, because the temperature decreases and the heat of reaction is
positive. Increasing inerts increases the temperature, increasing k, increasing the rate and hence increasing coversion.
The reaction could have essentially stopped at 4 kg for one of two reasons.
A. First, the reaction could have stopped because the temperature drops sufficiently to cause k to reach a very very small value so that the
rate is so small and reaction does not proceed farther. That is the reaction becomes frozen.
B. The second reason the reaction could have stopped is because it reaches equilibrium (as the temperature drops, so does Xe).
(1-5)
(1-2)
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 11 of 44
:
Note fixed Tτ0, if the total molar flow rate and temperature and pressure are constant (hence Cτ0) the ν0 is constant, consequently the
presence of inerts does not effect this equation except by increasing the temperature which increases k. Adding inerts to the system will
cause the temperature not to drop as much so that the rate will be faster and the conversion greater.
Fixed Tτ0
At equilibrium
(1-6)
Endothermic
(1-7)
Along the energy balance line, the temperature will continue to decrease until the reaction has reached essentially equilibrium, and the
adiabatic equilibrium conversion.
(1-8)
Again, increasing the amount of inerts increases the slope of the line, the energy balance line (B) causing the temperature not to drop as
much as the case with no inerts and as shown. In addition, the equilibrium conversion is increased.
Back to Problem 1
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 12 of 44
:
1 (b) TRUE. For an irreversible reaction, decreasing the flow rate will always increase conversion. Even if it's on the plateau, the conversion
still increases ever so slightly. The reactants spend a longer time in the reactor.
Back to Problem 1
Back to Chapter 8
1 (c) FALSE. If the exit conversion is essentially the equilibrium conversion (e.g., X = 0.999Xe), then the reactants spending more time in
the reactor as a result of a decrease in the flow rate will not affect conversion, because the reaction has reached equilibrium.
If the reaction had not reached equilibrium, then decreasing the flow rate could increase the conversion.
Back to Problem 1
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 13 of 44
:
1 (d) TRUE. Higher entering temperature, higher rate, higher equilibrium conversion, therefore greater extent of reaction (greater
conversion).
Back to Problem 1
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 14 of 44
:
1 (e) FALSE. If it is an endothermic, reversible reaction, then it will have a lower equilibrium conversion at a lower temperature (in
addition, the lower temperature will cause the specific rate, k, to be lower), resulting in a slower rate and thus smaller conversion.
Back to Problem 1
Back to Chapter 8
Problem 2
2 (a) TRUE. If it is an adiabatic system, then it has to be exothermic. Also, because both the temperature and conversion reach a plateau,
equilibrium has been reached. Adding inerts increases the slope of the energy balance line.
Irreversible
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 15 of 44
:
Reversible
(2-1)
The addition of inerts will lower the exit temperature and hence will increase both the equilibrium conversion and the exit conversion,
provided the rate is sufficiently large to always closely approach equilibrium, even at To, as shown in the figure below. As more and more
inerts continue to be added, the reactor approaches isothermal condition, To.
We now consider the case when the reaction is slow at the start (i.e. T = T0) but as it proceeds down the reactor the temperature
increases as does the rate and the conversion until it finally takes off (see = 0 below).
If we were to add inerts to the point that the reactor approached isothermal conditions and the reaction rate was very small, then under
these conditions very little conversion would be achieved (as in theta=4 above).
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 16 of 44
:
For an intermediate rate of reaction we could have
Adding inerts will increase the temperature for endothermic reaction of any order. Consequently, k will increase and the rate will increase
with increasing inerts, but only to a point.
(1-3)
(1-4)
We see that at very large values of the rate becomes very small and consequently very little conversion is achieved. Consequently there
is an optimum in the amount of inerts for a 2nd order reaction.
There would be an optimum value of thetaI for which the exit conversion is a maximum. As we initially increase thetaI we decrease the
maximum temperature reached, therefore increasing Xe. However, as we increase thetaI further, the rate decreases and we don't approach
Xe.
Back to Problem 2
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 17 of 44
:
Back to Chapter 8
2 (b) FALSE. Decreasing the flow rate will not change the exit condition because it is an equilibrium condition.
Back to Problem 2
Back to Chapter 8
2 (c) FALSE. We see that for the plot of entering temperature shown, equilibrium has already been reached in the reactor. If feed
temperature is increased, equilibrium conversion is decreased. Therefore, one can tell whether the exit conversion will increase or
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 18 of 44
:
decrease.
Back to Problem 2
Back to Chapter 8
Problem 3
3 (a) EXOTHERMIC. Temperature increases reaching a plateau in reactor A at the adiabatic equilibrium conversion.
Back to Problem 3
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 19 of 44
:
3 (b) REVERSIBLE. In reactor A, the conversion reaches a plateau (i.e.X=Xe) well below complete conversion, X=1.0, indicating a
reversible reaction.
Back to Problem 3
Back to Chapter 8
3 (c) A is adiabatic. B has a heat exchanger. As heat is removed in Reactor B, temperature drops, shifting equilibrium to the right to
increase conversion.
Back to Problem 3
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 20 of 44
:
3 (d)
In curve A (1000 K), the equilibrium conversion is virtually reached near the reactor entrance. However due to the high temperature, the
equilibrium conversion is very low. For curve B (300 K), this very low temperature results in an extremely low specific reaction rate (k).
Consequently, the reaction is so slow the reaction never takes off, resulting in a very small conversion. Therefore, there is an optimum
inlet temperature. You cannot tell whether or not conversion will increase because you do not know which side of the optimum you are on.
Back to Problem 3
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 21 of 44
:
3 (e)
There is an optimum inlet temperature. Therefore you cannot say whether or not conversion will increase or decrease if you increase T0. It
depends on which side of the optimum you are on.
Back to Problem 3
Back to Chapter 8
3 (f)
1. Very rapid rate and equilibrium is approached at 100 dm3. If the reactor were adiabatic, then conversion would remain the same after
V=100 dm3.
2. Reactor begins to cool down shifting equilibrium to the right, conversion slowly increases.
3. Reactants almost exhausted and low temperature results in a slow rate and conversion levels off.
Back to Problem 3
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 22 of 44
:
Back to Chapter 8
Problem 4
4 (a) As the temperature increases, so does the reaction rate until the equilibrium conversion is approached at which point the reaction
slows down. As the temperature drops, Xe increases, the reaction continues to shift to the right, thereby increasing conversion.
Back to Problem 4
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 23 of 44
:
4 (b)
Back to Problem 4
Back to Chapter 8
Solution: Higher flow rates will cause the temperature profile to flatten out more near the entrance to the reactor, so (A) is correct, as is
(D). (B) and (C) are not correct because for Fao=1, the temperature begins to decrease, Xe begins to increase, so the conversion should
increase but instead X reaches a plateau.
Back to Problem 4
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 24 of 44
:
Back to Chapter 8
Solution 5. The elementary isomerization of A to B was carried out adiabatically in a packed bed reactor. The following profiles were
obtained when pure A was fed to the reactor
1) The above profiles could represent an adiabatic system where the addition of inerts to the feed stream will increase the conversion.
2) If the reaction is irreversible a small decrease in the flow rate will produce a small increase in the conversion.
3) If the reaction is reversible a small decrease in the flow rate will produce a small increase in the conversion.
Solution: Ans: E
1) True. If it is an adiabatic system then it has to be endothermic because the temperature decreases. Increasing inerts increases the
exit temperature and hence the conversion is higher.
2) False. The reaction has reached a sufficiently low temperature the reaction is essentially frozen. Thus, changing the flow rate will not
produce a moderate increase the temperature or conversion.
3) False. If the exit condition is an equilibrium condition, then a small change in the flow rate will not affect the equilibrium condition.
Hence, it will not change the conversion. If the reaction is frozen, as in 2, then neither the conversion nor temperature will increase
significantly.
Back to Problem 5
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 25 of 44
:
Solution 6. The elementary isomerization of A to B was carried out in a packed bed reactor. The following profiles were obtained when
pure A was fed to the reactor
An
1. increase in the feed temperature will increase the conversion. (True)
A
2.decrease in feed temperature will increase the conversion.(False)
3. There could be a very very very large heat exchanger attached to the reactor with the heat flow given by (False)
1) The higher temperature, the higher equilibrium conversion, higher rate, therefore greater conversion.
2) If it is an endothermic reaction then it should have smaller equilibrium conversion at low temperature and also a smaller k resulting in
a slower rate and smaller conversion.
3) Because final temperature is 500 K and reaction is either frozen (i.e., the temperature is so low the reaction rate is virtually zero or it
is in equilibrium. The ambient temperature of the heat exchanger cannot be 400.
Back to Problem 6
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 26 of 44
:
Back to Chapter 8
Solution 7. The elementary isomerization of A to B was carried out in a packed bed reactor. The following profiles were obtained when
pure A was fed to the reactor
Inerts were added to a reactor system while T0, P0, and n0 were kept constant. Which of the following figures the exit conversion is as a
function of the qI is correct? i.e. qI (qI = FI0/FA0)
Solution: Ans: C. Inerts provide sensible heat to raise temperature. The combined mole balance rate law and stoichiometry,
temperature will be higher because inerts supply sensible heat. The higher temperature the higher rate and the greater the conversion.
Back to Problem 7
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 27 of 44
:
Solution 8. The elementary, gas phase reaction
takes place in a packed bed reactor. The following profiles were obtained
1. The above profiles could represent an adiabatic system where the addition of a small to moderate amount of inerts will increase the
conversion. (True)
2. The above profiles could represent an adiabatic system where decreasing the flow rate will increase the conversion. (False)
3. The above profiles could represent an adiabatic system where if the feed temperature is increased, one cannot tell from the above
profiles whether or not the conversion will increase or decrease. (False)
4. There could be a heat exchanger on the reactor for which the heat flow is (True)
Explanation:
1) TRUE ( ) If it is an adiabatic system, then it has to be exothermic. Addition of a moderate amount of inerts will
lower the exit temperature increase the equilibrium conversion and hence will increase the conversion. If a very large amount of
inerts are added then the conversion could decrease since the combined M.B., R.L., and Stoich is
In addition, k will decrease as inerts are added because the temperature is decreased.
2) FALSE Decreasing the flow rate will not change the exit condition because it is an equilibrium condition.
3) FALSE One can tell becuase equilibrium is achieved early in the reactor if feed temperature is increased, equilibrium conversion
is decreased.
4) TRUE The ambient temperature is 500 K, the same as the final equilibrium temperature. Consequently if the reaction is
endothermic, heating the reactor will increase the rate, Xe and X.
Answer: E
Back to Problem 8
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 28 of 44
:
Solution 9. The following conversion profiles were measured in two PFRs, (A and B) for the same reaction
TRUE
A. The reaction is exothermic and reversible.
FALSE
B. The reaction is exothermic and irreversible (equilibrium is reached).
FALSE
C. The reaction is endothermic and irreversible (temperature increases, exothermic).
FALSE
D. The reaction is endothermic and reversible (temperature increases, exothermic).
Cannot
E. tell for sure if any, some, or all the above are true.
Back to Problem 9
Back to Chapter 8
Solution 10. The exit conversion from an adiabatic PFR is shown below as a function of θI for constant ν0, T0 and P0
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 29 of 44
:
The
1. reaction could be a second order endothermic reaction. False.
The
2. reaction could be a second order exothermic reaction. False.
The
3. reaction could be a first order exothermic reaction. True.
The
4. reaction could be a first order endothermic reaction. True.
The
5. reaction could be an irreversible zero order exothermic reaction. False.
Explanation:
3) TRUE ( ) , does not appear in this combined mole balance, rate law, and
stoichiometry, but as increases, temperature decreases, k decreases, and Kc increases as does Xe.
Even at T = T0 down the reactor, equilibrium is reached. So it could be a first order exothermic reaction. TRUE
k is so low at T0, reaction never really takes off. In this case the answer would be FALSE. But because Case I is possible, the overall
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 30 of 44
:
answer is TRUE.
increases.
Case I: E is very small so that decreasing the temperature by adding inerts does not change k very much at all. Thus,
Case II: Large E, decreasing the temperature by adding inerts decreases T and k at the exit. Smaller k, smaller conversion.
Back to Problem 10
Back to Chapter 8
Solution 11. The exit conversion from an adiabatic PFR is shown below as a function of θI for constant ν0, T0 and P0
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 31 of 44
:
10. Both statements 4 and 5 are true.
Explanation:
answer 6
True. In region 1 increasing qI increases temperature and X. In region 2, . Large decrease, therefore X
decreases.
2) True. In region 1, adding inserts could decrease temperatures and increase equilibrium conversion. In region 2
3) True. does not appear in this combined mole balance, rate law, and stoichiometry, but as increases,
temperature decreases, k decreases, and Kc increases as does Xe.
3) True. does not appear in this combined mole balance, rate law, and stoichiometry, but as increases,
temperature decreases, k decreases, and Kc increases as does Xe.
4) False. For first order independent of inserts except in k and KC. Increase θI increase T, k, and X up until
we reach isothermal conditions then X will be independent of &thetaI.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 32 of 44
:
5) False. , conversion increases as θI increases.
Case I: E is very small so that decreasing the temperature by adding inerts does not change k very much at all. Thus,
Case II: Large E, decreasing the temperature by adding inerts decreases T and k at the exit. Smaller k, smaller conversion.
Back to Problem 11
Back to Chapter 8
Solution 12. The exit conversion from an adiabatic PFR is shown below as a function of θI for constant constant ν0, T0 and P0
A) True if DHRX is very small such that temperature does not change upon adding inerts and , then for large
Kc, X could decrease as qI increases.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 33 of 44
:
C) True. , increase inerts, could decrease T, k and X
D) False.
Increases with qI
Back to Problem 12
Back to Chapter 8
Solution 13. The equilibrium conversion is shown below as a function of catalyst weight
1. The reaction could be first order endothermic and carried out adiabatically. True.
2. The reaction is first order endothermic and reactor is heated along the length with Ta being constant. False.
3. The reaction is second order exothermic and cooled along the length of the reactor with Ta being constant. False.
4. The reaction is second order exothermic and carried out adiabatically. True.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 34 of 44
:
Explanation:
1) As temperature drops so does KC and Xe. However X continues to increase until Xe is reached.
3) If cooling, temperature would decrease. Xe would increase at some point if there were heating or cooling.
4)
Back to Problem 13
Back to Chapter 8
Solution 14. The equilibrium conversion is shown below as a function of catalyst weight
1. The reaction could be first order endothermic and carried out adiabatically.
2. The reaction could be first order endothermic and reactor is heated along the length with Ta being constant. True.
3. The reaction could be second order exothermic and cooled along the length of the reactor with Ta being constant. True.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 35 of 44
:
4. The reaction could be second order exothermic and carried out adiabatically.
Answer: B
Back to Problem 14
Back to Chapter 8
Solution 15. The equilibrium conversion is shown below as a function of catalyst weight
A. False. The reaction could be first order endothermic and carried out adiabatically. Temperature will drop.
B. False. The reaction could be first order endothermic and reactor is heated along the length with Ta being constant. If 1st order
endothermic, then
C. False. The reaction could be second order exothermic and cooled along the length of the reactor with Ta being constant. If 2nd order
exothermic, then
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 36 of 44
:
D. False. The reaction could be second order exothermic and carried out adiabatically. If 2nd order exothermic and adiabatic, then
E. True. The reaction could be first order endothermic with very high heating rate. If heating rate such that temperature always
increases, then
Back to Problem 15
Back to Chapter 8
Solution 16. The equilibrium conversion is shown below as a function of catalyst weight
1) False. The reaction could be first order endothermic and carried out adiabatically. If adiabatic, then
2) True. The reaction could be first order endothermic and reactor is heated along the length with Ta being constant.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 37 of 44
:
3) True. The reaction could be second order exothermic and cooled along the length of the reactor with Ta being constant.
4) False. The reaction could be second order exothermic and carried out adiabatically.
Answer A
Back to Problem 16
Back to Chapter 8
Solution 17. The equilibrium conversion and temperature are shown below as a function of catalyst weight for three sets
of conditions
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 38 of 44
:
1. The figures could correspond to an exothermic reversible reaction with too high of a cooling rate. True. k(T) smaller \ X smaller
2. The figures could correspond to an exothermic irreversible reaction with too high of a cooling rate. True. k(T) smaller \ X smaller
3. The figures could correspond to an endothermic reversible reaction with a high heating rate. True. T higher, k larger, Xe larger,
heating rate of (3) > (2) > (1). For endothermic reactions
4. The figures could correspond to an endothermic irreversible reaction with a high heating rate. True. For endothermic reactions X
always increases as T increases.
Answer: E
Back to Problem 17
Back to Chapter 8
Solution 18. The conversion from an adiabatic PFR is shown below as a function of temperature
1. 90% conversion could be achieved for a first order reaction by increasing the inerts by a factor of 100 or greater for entering
temperature of 700 K. True.
2. 90% conversion could be achieved for a second order reaction by adding a very large heat exchanger with a very large area for an
entering temperature of 700 K. True.
3. For a small but fixed reactor length, one is more likely to get close to the adiabatic equilibrium conversion for an entering
temperature of 500 K than an entering temperature of 900 K. False.
4. The reaction could be a second order endothermic reaction carried out with a very large heat exchanger attached to the reactor.
False.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 39 of 44
:
5. If the reaction is carried out adiabatically, the temperature in a CSTR will drop more for an entering temperature of 900 K then that
for an entering temperature of 500 K. True.
Explanation:
1.
2. Eventually becomes isothermal as the product of UA continually increases. Same as (1) above.
3. High T0, higher rate, equilibrium conversion reached near entrance to reactor.
4. False. If very large heat exchanger, the energy balance term will be essentially vertical.
Back to Problem 18
Back to Chapter 8
Solution 19.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 40 of 44
:
1. The above reaction could be exothermic.
2. The above reaction could be endothermic.
3. The above reaction could be first order.
4. The above reaction could be second order.
5. The above reaction is not carried out adiabatically.
Answer: D
Explanation:
1). True.
2) True.
3) True.
4). True.
5) False ? if then
or
Back to Problem 19
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 41 of 44
:
Solution 20.
Explanation:
2)
3) True.
3) True.
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 42 of 44
:
5) True. If endothermic
Back to Problem 20
Back to Chapter 8
Solution 21.
Answer: D
Explanation:
Back to Problem 21
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 43 of 44
:
Solution 22.
Explanation:
Back to Problem 22
Back to Chapter 8
https://public.websites.umich.edu/~elements/course/lectures/eight/test5.htm 15/03/2024, 3 58 PM
Page 44 of 44
: