Professional Documents
Culture Documents
Power Tools
Power Tools
arbor collar
arbor nut
This bit is used for drilling wood and other soft materials, but not for
drilling metal. As a rule, the point of a bit should be sharper for softer
materials than for harder ones.
Band saw
Used for trimming accurately to a line used for marking out or making
a material flat. Guards and dust extraction should be used. PPE
Bench Grinder
This lever, placed just under the saw table surface on the
front of the cabinet, locks the angle setting of the blade.
bore
Chain saw
This saw may be needed to cut heavy timbers, posts, and pilings. Both
gas and electric models are available,but gasoline powered types are
more powerful.
chipper
chuck
Chuck Key
All bits are held in the drill by this and they can
be either keyed or key-less.
Circular Saw, utility saw, electric
handsaw, or builder's saw
These saws are designed to cut lumber and
boards to size for a project.
This is a power drill that get their power from AC wall plug source. The drill is most commonly used to
make holes by spinning drill bits into wood, metal, plastic and other materials it also used to drive screws
or to cut small holes in lumber, or to prepare a site for a nail or screw.
Cordless Drill
This is a power drill that get their power from DC battery source and usually
contain a rechargeable battery pack that runs the motor. This drill is useful for
working in awkward areas or in areas where a power source is hard to find.
Detail Grinder
This grinder uses small attachments, also called points, to smooth and polish
intricate metallic work. These shank mounted points attachments, are
commonly found in sizes ranging from 1/16 to 1/4 inch.
disc sander
This is a drill press also known as a pedestal drill, pillar drill, or bench drill) is a fixed style
of drill that may be mounted on a stand or bolted to the floor or workbench. Portable
models with a magnetic base grip the steel workpieces they drill.
This is a motor belt and by adjusting the location of the drive belt on
the pulleys you can set the drill press to five different speeds
drum sander
This gun looks like a drill, but has a "nose" instead of a chuck. The nose holds
an interchangeable 0.25 inches 6 mm shank bit, commonly known as a tip. The
most common type of tip is a 1 inch 25 mm #2 phillips.
Electromagnetic drill
This drill is a portable drill mounted that is used for drilling thick metal. When
the drill is placed on metal and is turned on, the magnetic base will hold the
drill in place for drilling.The drill can also be rotated on the base.
feather board
Finishing Sander
This bit is also used in wood. The bit size is measured by the
spade's diameter, which ranges from 1/2 to 1 1/2 inches.
Forstner Drill Bit
This saw can crosscuts, miters, bevels, and makes compound cuts. It
crosscuts, miters, bevels, and makes compound cuts on any stock up
to 2 x 12
guide fence
Hammer Drill
This drill has a pounding action that lets you drill into concrete, brick,
or tile. The bit rotates and hammers at the same time, allowing you to
drill much faster than you could with a regular drill.
These demolition jacks are used for pushing heavy machinery and other heavy objects; for pulling
wheels, bearings, gears, and cylinder liners; and for straightening or bending frames.They have two basic
parts: the pump and the cylinder.The two parts are joined by a high-pressure hydraulic hose.
kickback guard
This router bit cuts a 45-degree miter with a tongue and groove. When correctly cut, the
parts go together at a perfect 90-degree angle and the interlocking tongues and grooves
make for lots of mechanical strength and glue surface area.
Pneumatic Drill
This drill is powered by compressed air from an air hose. They have
many of the same parts, controls, and uses as electric drills.
This sander is used to remove rough areas from large, flat sections of
wood: for trimming off excess wood; and for stripping old finishes
such as paint and varnish.
This saw is used when it is better to move the saw to the work than to
move the work to the saw. It can be used to cut pipe, metal, plastic,
wood, and irregularly shaped materals
These guns are used to drive various fasteners into concrete and
structural steel.The gun ignites blasting powder to drive fasteners into
tough material.The tool may be either direct acting or indirect acting.
This nail gun greatly speed up the installation of materials such as wallboard,
molding, framing members, and shingles.They are driven by compressed air
traveling through air lines connected to an air compressor.
This is a special saw to operate carpenter sets the angle from a scale
marked off in degrees.The cut is made by pulling downward on the
handle.
These two in one guns which most of them are air pneumatic powered this is a hand-held machine used
to drive heavy metal staples into wood, plastic, or masonry.They speeds up work and allows the
carpenter to work in tight places where swinging a hammer might be difficult or impossible.
This saw is especially useful in cutting compound miters. It is also a good tool
for cutting larger dimension lumber which is difficult to slide across a saw
table. The proper saw setup for cutting a large sheet of plywood.
radial arm saw's arm
raker tooth
This is the some crosscut saws use special teeth called "rakers"
designed to clean out the cut strips of wood from the kerf. Crosscut
saws generally have larger teeth than rip saws.
This sander can be used circular and back and forth. This
sander combines both types of movement into one sander.
These saws are designed for more heavy duty jobs. You can use longer and
tougher blades than the other saws. They can saw through walls or ceilings
and create openings for windows, plumbing lines, and more.
ring test
router/shaper
These saws have very fine blades, which makes them great tools for doing delicate and
intricate work, such as cutting out patterns or irregular shapes from wood or thin, soft
metals.They are also one of the best tools for cutting circles.
Sanding disc
This is a round disc , flat piece that remove surface defects, rust, paint
and corrosion, making your projects look as good as new.
saw guard
Soldering Guns
Soldering Iron
This iron is a tool used to melt solder. This iron's heat produced as
current passes through a heating element.
The heating element uses a coil with high resistance wire.
This cutter head create the grooves running the length of your
board.Also, there are no aluminum cutter heads produced for jointer
or planers.
splitter
Table Saw
thickness planer
trigger lock
A small lever, switch, or part that you push or pull to activate a locking catch
or spring. Activation this device causes the power tool to stay in the operating
mode even when you finger is not on it. Do not use this with hand power tools.
wingnut
Wood lathe
Wood shaper
This is a shaperit does essentially the same job as the router table, with the main difference being that this
shaper is a stationary machine designed for larger volume work while a router is a hand tool for lighter
duty work. Routers can also be mounted on a router table, and used as a stationary tool.
This is what the gears look like in a worm drive circular saw.
These gears create great torque which turns the blade.