Professional Documents
Culture Documents
E Power Transmission
E Power Transmission
Table of Contents 1
Power Engineering | Smart Grid | Micro Grid 2
Power transmission 2
EUL High-voltage transmission lines 2
EUL 1 Investigations on Three-phase Transmission Lines 3
EUL 2 Parallel and series connection of transmission lines 14
EUL 3 Transmission Line with Earth-fault Compensation 25
EUL 4 Transmission Systems with a Synchronous Generator 34
EUL 5 Investigations on three phase cables 46
EUL 6 Combined networks of cables and lines 56
EUL 7 Controlling flow of power in meshed networks 67
EUL 8 Load-dependent voltage regulation of a power transmission line 78
ELP Protective systems for high-voltage transmission lines 88
ELP 1 Overcurrent time protection for lines 88
ELP 2 Directional overcurrent time protection for lines 99
ELP 3 Overvoltage and undervoltage protection 108
ELP 4 Directional power protection 118
ELP 5 Earth-fault voltage protection 128
ELP 6 Protection of Parallel-connected Lines 139
Supplement to basic set, consisting of: 140
ELP 7 High-speed distance protection 151
EDC1 High-voltage direct current transmission (HVDC) 162
The Lucas-Nülle training systems have been designed in anticipation of the newest developments:
Smart measuring instruments provided with various communication interfaces (e.g. LAN, RS485, USB) and
control elements
SCADA Power Engineering Lab software for the intelligent control and evaluation of "smart grids" using Soft
PLC
SCADA software designed for educational purposes
Permits investigation of dynamically alternating loads and power generation inside the laboratory
Intelligent energy management
Modular integration of renewable energies into a smart grid using protective engineering
Wind power plant with doubly-fed asynchronous generator (DFIG) and synchronisation to the grid
Interactive multimedia training course
Power transmission
Power transmission
High-voltage networks are usually operated with voltages in the region of 110 kV to 380 kV, whereby urban areas and
large-scale industrial facilities are supplied with 110 kV, and 380 kV is used for long-distance transmission lines. The
line simulation system is designed for operation at model voltages between 110 V and 380 V. Various voltage levels
and line lengths can be selected via corresponding overlay masks. Examinations with the training system can be
performed off-load, in normal operating mode, in the presence of a short-circuit or earth fault, with or without earth-
fault compensation. The system also permits assembly of complex networks by connecting the line simulation models
in parallel or series. The voltage can be supplied via a fixed grid or synchronous generator.
For your safety, this investigation of 380-kV and 110-kV transmission lines and how they are connected together is
carried out using low voltage, but without losing the actual properties of genuine high-voltage lines. These realistic
simulations of a 380-kV transmission line and a 110-kV cable link are automatically switched between different line
lengths once the appropriate overlay mask is put in place. By using simulations of various line lengths, it is possible to
assemble complex transmission networks.
Earth-fault compensation in electric power supply networks is designed to offset earth leakages occurring in outer
conductors.
Restricted to three-phase systems, earth-fault compensation makes use of a special Petersen coil named after its
inventor and which is also known as an earth-fault quenching coil. This coil compensates the electric current at the
earth-fault point, thereby preventing consequential malfunctions in the electrical system.
The objective here is to measure characteristic power transmission parameters on simulated, three-phase, parallel-
connected lines fed via a fixed network or a generator, and perform quantitative as well as qualitative assessments of
operational relationships.
Training contents:
Training contents:
Three-phase line simulation of a high voltage overhead power line with different lengths for measuring various
operational states (open-line, matched, short-circuit). Scale factor 1/1000 for current and voltage. Automatic
modification of wire length as soon as the corresponding overlay is in place.
Current: up to 2A
Weight: 6kg
2
Capacitive load, three-phase, 1kW
CO3301-3E
1
3
Variable Ohmic load, three-phase, 1kW
CO3301-3F
1
Three synchronously adjustable circular rheostats with scale 100 - 0%, each with a fuse in the sliding-contact
connection.
4
Inductive load, three-phase, 1kW
CO3301-3D
1
1,2H (0,65A), 1,6H (0,5A), 2H (0,45A), 2,4H (0,35A), 2,8H (0,30A), 3,2H (0,25A)
5
Power switch module
CO3301-5P
1
Media:
Pos.
Product name
Bestell-Nr.
Anz.
6
Interactive Lab Assistant: High-voltage transmission lines
SO2800-3L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Voltage distribution
Earth-fault compensation
Variable transformers
Transformer with in-phase regulation (in-phase booster)
Transformer with regulation in quadrature (quadrature booster)
Phase-angle-regulating transformer (phase-shifting transformer)
Affect flow of power via two identical conductors parallel to one another
Software:
Pos.
Product name
Bestell-Nr.
Anz.
7
Software SCADA Viewer
SO4001-3H
1
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
8
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
2
1x 1 m yellow
2x 2 m yellow
9
USB 2.0 Ethernet adapter, 10/100
LM8257
1
Lucas Nülle GmbH Page 7/171 www.lucas-nuelle.us
USB 2.0 high-speed device
10
5-Port Ethernet Switch
LM9988
2
Power supply:
Pos.
Product name
Bestell-Nr.
Anz.
11
Adjustable 3-phase power supply, 0-450V/2A
CO3301-3Z
1
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
12
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
15
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
2
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
16
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
7
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
17
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
18
Safety measurement cable 4mm, 50cm/20", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8L
6
Colour: black
Length: 50 cm
Wire cross section 2.5 mm2
ratings deliver: 600 V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
19
Safety measurement cable 4mm, 25cm/10", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8B
3
colour: black
length: 25 cm / 10"
cable cross-section 2,5 mm2
ratings deliver: 600V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
20
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Lucas Nülle GmbH Page 11/171 www.lucas-nuelle.us
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
21
Protected power distribution for working stations
ST8008-8N
1
400-V CEE distribution panel with automatic circuit breakers for attachment to profiles on experiment trolleys or direct
to table-top.
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
23
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
24
Display for Power Transmission equipment
ST8000-4L
1
25
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
Three-phase line simulation of a high voltage overhead power line with different lengths for measuring various
operational states (open-line, matched, short-circuit). Scale factor 1/1000 for current and voltage. Automatic
modification of wire length as soon as the corresponding overlay is in place.
Current: up to 2A
Weight: 6kg
27
Power-Multimeter
CO5127-2A
1
The areas of electrical machines, power electronics and drive technology pose particular problems for measuring
instruments. In addition to high-performance overload protection, the acquisition of measurement values must be
performed accurately independently of the curve's shape. The universal measuring device has been designed
particularly to satisfy these requirements. It can simultaneously replace as many as four different measuring
instruments – constituting a current/voltmeter, power and phase-angle meter all in one. The graphic display allows for
both student as well demonstration experiments. The VI Starter software included allows for visualisation of
measurements on a PC.
Simultaneous, measurement of voltage and current independent of the curve shape (max. 600 V, 20 A)
(measurement of clocked voltages)
Calculation of active, apparent and reactive power as well as the power factor
Measurement of the total rms (RMS-AC+DC), AC rms (RMS-AC) and arithmetic mean (AV-AC+DC)
Independent inputs for current and voltage
Impervious to electrical damage up to 20 A/600 V
Large-scale, touch colour graphic display (5.7")
Large-scale display or display of up to 4 measurement values
Digital display with bargraph
Isolated USB interface
Internal resistance: current path 10 mΩ, voltage path 10 MΩ
Voltage ranges: 30, 300, 600 V
The VI Starter software allows all the measurements to be displayed on the PC. Up to 17 different displays can be
opened.
Media:
Pos.
Product name
Bestell-Nr.
Anz.
28
Interactive Lab Assistant: High-voltage transmission lines
SO2800-3L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Voltage distribution
Earth-fault compensation
Variable transformers
Transformer with in-phase regulation (in-phase booster)
Transformer with regulation in quadrature (quadrature booster)
Phase-angle-regulating transformer (phase-shifting transformer)
Affect flow of power via two identical conductors parallel to one another
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
30
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
2
1x 1 m yellow
2x 2 m yellow
31
USB 2.0 Ethernet adapter, 10/100
LM8257
1
32
5-Port Ethernet Switch
LM9988
2
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
34
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
37
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
2
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
38
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
7
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
39
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
40
Safety measurement cable 4mm, 50cm/20", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8L
6
Colour: black
Length: 50 cm
Wire cross section 2.5 mm2
ratings deliver: 600 V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
41
Safety measurement cable 4mm, 25cm/10", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8B
3
colour: black
length: 25 cm / 10"
cable cross-section 2,5 mm2
ratings deliver: 600V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
42
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Lucas Nülle GmbH Page 22/171 www.lucas-nuelle.us
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
43
Protected power distribution for working stations
ST8008-8N
1
400-V CEE distribution panel with automatic circuit breakers for attachment to profiles on experiment trolleys or direct
to table-top.
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
45
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
46
Display for Power Transmission equipment
ST8000-4L
1
47
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
This earth fault compensation unit is connected between the neutral line and the earth to compensate the capacitive
earth-fault current by selecting the correct inductance. The unit can be adjusted to variable settings in order to
facilitate matching of the earth-fault inductors to the various switching states of the power supply system. (Petersen
coil)
Media:
Pos.
Product name
Bestell-Nr.
Anz.
49
Interactive Lab Assistant: High-voltage transmission lines
SO2800-3L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Lucas Nülle GmbH Page 25/171 www.lucas-nuelle.us
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Voltage distribution
Earth-fault compensation
Variable transformers
Transformer with in-phase regulation (in-phase booster)
Transformer with regulation in quadrature (quadrature booster)
Phase-angle-regulating transformer (phase-shifting transformer)
Affect flow of power via two identical conductors parallel to one another
Software:
Pos.
Product name
Bestell-Nr.
Anz.
50
Software SCADA Viewer
SO4001-3H
1
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
51
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
2
1x 1 m yellow
2x 2 m yellow
53
5-Port Ethernet Switch
LM9988
2
Power supply:
Pos.
Product name
Bestell-Nr.
Anz.
54
Adjustable 3-phase power supply, 0-450V/2A
CO3301-3Z
1
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
55
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
Measuring instruments:
Pos.
Product name
Bestell-Nr.
Anz.
56
Three-phase power quality meter, display and long-term memory
CO5127-1S
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
58
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
2
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
59
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
7
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
60
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
61
Safety measurement cable 4mm, 50cm/20", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8L
6
Colour: black
Length: 50 cm
Wire cross section 2.5 mm2
ratings deliver: 600 V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
62
Safety measurement cable 4mm, 25cm/10", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8B
3
colour: black
length: 25 cm / 10"
cable cross-section 2,5 mm2
ratings deliver: 600V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
63
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Lucas Nülle GmbH Page 31/171 www.lucas-nuelle.us
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
64
Protected power distribution for working stations
ST8008-8N
1
400-V CEE distribution panel with automatic circuit breakers for attachment to profiles on experiment trolleys or direct
to table-top.
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
66
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
67
Display for Power Transmission equipment
ST8000-4L
1
68
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
70
Synchronization Unit
CO3212-6V
1
synchronizer display (comprising 3 lamps) is used to display voltage and phase angles between generator and
power supply circuit (light-dark indication)
zero voltmeter
double frequency meter
double voltmeter
digital synchronoscope
synchronization switch
Lucas Nülle GmbH Page 34/171 www.lucas-nuelle.us
Operating voltage: 400 V
Dimensions: 297 x 452 x 125 mm (HxWxD)
Weight: 2 kg
71
Three-phase synchronous machine with smooth core rotor, 1 kW
SE2682-5Q
1
The servo-machine test bench is a complete testing system for examining electrical machines and drives. It consists
of a digital controller, a brake and the ActiveServo software. The system combines state-of-the-art technology with
ease of operation.
The system also allows manual and automated synchronization to be carried out.
The motor and sensor leads are connected via polarity-safe plugs. The machine has thermal monitoring and, in
conjunction with the controller, it constitutes a driving and braking system that is free of drift and requires no
Lucas Nülle GmbH Page 35/171 www.lucas-nuelle.us
calibration.
ActiveServo is a program for recording characteristics of machines and for determining dynamic and static operating
points. It emulates eight different loads (flywheel, pump, fan, calander, lifting drive, compressor, winding gear,
arbitrarily configurable time-dependent load) for which the parameters can be individually configured.
Features:
73
Rubber coupling sleeve for 1kW machines
SE2662-6A
1
74
Coupling guard with LED lighting for 1kW machines
SE2662-7D
1
Connectable plastic guard as contact protection of the rotating coupling between two coupled machines
Media:
Pos.
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Voltage distribution
Earth-fault compensation
Variable transformers
Transformer with in-phase regulation (in-phase booster)
Transformer with regulation in quadrature (quadrature booster)
Phase-angle-regulating transformer (phase-shifting transformer)
Affect flow of power via two identical conductors parallel to one another
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
77
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
2
1x 1 m yellow
2x 2 m yellow
78
USB 2.0 Ethernet adapter, 10/100
LM8257
1
79
5-Port Ethernet Switch
LM9988
2
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
81
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
84
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
2
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
85
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
7
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
86
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
87
Safety measurement cable 4mm, 50cm/20", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8L
6
Colour: black
Length: 50 cm
Wire cross section 2.5 mm2
ratings deliver: 600 V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
88
Safety measurement cable 4mm, 25cm/10", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8B
3
colour: black
length: 25 cm / 10"
cable cross-section 2,5 mm2
ratings deliver: 600V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
89
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Lucas Nülle GmbH Page 43/171 www.lucas-nuelle.us
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
90
Protected power distribution for working stations
ST8008-8N
1
400-V CEE distribution panel with automatic circuit breakers for attachment to profiles on experiment trolleys or direct
to table-top.
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
92
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
93
Display for Power Transmission equipment
ST8000-4L
1
94
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
Three-phase line simulation of a high voltage underground cable with different lengths for measuring various
operational states (open-line, matched, short-circuit). Scale factor 1/1000 for current and voltage.
Current: 1A
Weight: 5kg.
96
Conversion station 380 V/110 V
CO3301-3M
Transformer for supplying electricity to simulated transmission line. Scale 1/1000 for voltage and current on the
secondary side.
Media:
Pos.
Product name
Bestell-Nr.
Anz.
97
Interactive Lab Assistant: High-voltage transmission lines
SO2800-3L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Voltage distribution
Earth-fault compensation
Variable transformers
Transformer with in-phase regulation (in-phase booster)
Transformer with regulation in quadrature (quadrature booster)
Phase-angle-regulating transformer (phase-shifting transformer)
Affect flow of power via two identical conductors parallel to one another
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
99
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
2
1x 1 m yellow
2x 2 m yellow
100
USB 2.0 Ethernet adapter, 10/100
LM8257
1
101
5-Port Ethernet Switch
LM9988
2
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
103
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
106
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
2
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
107
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
7
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
108
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
109
Safety measurement cable 4mm, 50cm/20", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8L
6
Colour: black
Length: 50 cm
Wire cross section 2.5 mm2
ratings deliver: 600 V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
110
Safety measurement cable 4mm, 25cm/10", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8B
3
colour: black
length: 25 cm / 10"
cable cross-section 2,5 mm2
ratings deliver: 600V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
111
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Lucas Nülle GmbH Page 53/171 www.lucas-nuelle.us
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
112
Protected power distribution for working stations
ST8008-8N
1
400-V CEE distribution panel with automatic circuit breakers for attachment to profiles on experiment trolleys or direct
to table-top.
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
114
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
115
Display for Power Transmission equipment
ST8000-4L
1
116
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
Three-phase line simulation of a high voltage underground cable with different lengths for measuring various
operational states (open-line, matched, short-circuit). Scale factor 1/1000 for current and voltage.
Current: 1A
Weight: 5kg.
118
Conversion station 380 V/110 V
Transformer for supplying electricity to simulated transmission line. Scale 1/1000 for voltage and current on the
secondary side.
119
Three-phase power quality meter, display and long-term memory
CO5127-1S
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
Media:
Pos.
Lucas Nülle GmbH Page 57/171 www.lucas-nuelle.us
Product name
Bestell-Nr.
Anz.
120
Interactive Lab Assistant: High-voltage transmission lines
SO2800-3L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Voltage distribution
Earth-fault compensation
Variable transformers
Transformer with in-phase regulation (in-phase booster)
Transformer with regulation in quadrature (quadrature booster)
Phase-angle-regulating transformer (phase-shifting transformer)
Affect flow of power via two identical conductors parallel to one another
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
122
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
2
1x 1 m yellow
2x 2 m yellow
123
USB 2.0 Ethernet adapter, 10/100
LM8257
1
124
5-Port Ethernet Switch
LM9988
2
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
126
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
129
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
2
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
130
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
7
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
131
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
132
Safety measurement cable 4mm, 50cm/20", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8L
6
Colour: black
Length: 50 cm
Wire cross section 2.5 mm2
ratings deliver: 600 V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
133
Safety measurement cable 4mm, 25cm/10", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8B
3
colour: black
length: 25 cm / 10"
cable cross-section 2,5 mm2
ratings deliver: 600V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
134
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Lucas Nülle GmbH Page 64/171 www.lucas-nuelle.us
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
135
Protected power distribution for working stations
ST8008-8N
1
400-V CEE distribution panel with automatic circuit breakers for attachment to profiles on experiment trolleys or direct
to table-top.
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
137
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
138
Display for Power Transmission equipment
ST8000-4L
1
139
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
Variable transformers
Transformer with in-phase regulation (in-phase booster)
Transformer with regulation in quadrature (quadrature booster)
Phase-angle-regulating transformer (phase-shifting transformer)
Affect flow of power via two identical conductors parallel to one another
Comparison between theory and practice
Transformer for feeding the transmission line model. Scale factor 1:1000 for secondary current and voltage.
141
Transmission line model 150km/300km (93.2miles/186.4miles)
CO3301-3A
1
Three-phase line simulation of a high voltage overhead power line with different lengths for measuring various
operational states (open-line, matched, short-circuit). Scale factor 1/1000 for current and voltage. Automatic
modification of wire length as soon as the corresponding overlay is in place.
Current: up to 2A
Weight: 6kg
142
Three-phase power quality meter, display and long-term memory
CO5127-1S
1
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
Pos.
Product name
Bestell-Nr.
Anz.
143
Interactive Lab Assistant: High-voltage transmission lines
SO2800-3L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Voltage distribution
Variable transformers
Transformer with in-phase regulation (in-phase booster)
Transformer with regulation in quadrature (quadrature booster)
Phase-angle-regulating transformer (phase-shifting transformer)
Affect flow of power via two identical conductors parallel to one another
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
145
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
2
1x 1 m yellow
2x 2 m yellow
146
USB 2.0 Ethernet adapter, 10/100
LM8257
1
147
5-Port Ethernet Switch
LM9988
2
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
149
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
152
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
2
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
153
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
7
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
154
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
155
Safety measurement cable 4mm, 50cm/20", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8L
6
Colour: black
Length: 50 cm
Wire cross section 2.5 mm2
ratings deliver: 600 V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
156
Safety measurement cable 4mm, 25cm/10", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8B
3
colour: black
length: 25 cm / 10"
cable cross-section 2,5 mm2
ratings deliver: 600V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
157
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Lucas Nülle GmbH Page 75/171 www.lucas-nuelle.us
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
158
Protected power distribution for working stations
ST8008-8N
1
400-V CEE distribution panel with automatic circuit breakers for attachment to profiles on experiment trolleys or direct
to table-top.
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
160
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
161
Display for Power Transmission equipment
ST8000-4L
1
162
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training content:
The purpose of this controllable transformer is to compensate for the fluctuations in voltage output from power
transformers which arise from changes in load. It achieves this by modifying the transformation ratio on the side
where the voltage is in excess. The component can be used as a step-up or step-down transformer. Control is
handled via the inputs for increasing or decrease the voltage, e.g. with the help of the power quality meter (CO5127-
1S).
Media:
Pos.
Product name
Bestell-Nr.
Anz.
164
Interactive Lab Assistant: High-voltage transmission lines
SO2800-3L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Voltage distribution
Earth-fault compensation
Variable transformers
Transformer with in-phase regulation (in-phase booster)
Transformer with regulation in quadrature (quadrature booster)
Software:
Pos.
Product name
Bestell-Nr.
Anz.
165
Software SCADA Viewer
SO4001-3H
1
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
166
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
2
1x 1 m yellow
2x 2 m yellow
167
USB 2.0 Ethernet adapter, 10/100
LM8257
1
168
Lucas Nülle GmbH Page 81/171 www.lucas-nuelle.us
5-Port Ethernet Switch
LM9988
2
Power supply:
Pos.
Product name
Bestell-Nr.
Anz.
169
Adjustable 3-phase power supply, 0-450V/2A
CO3301-3Z
1
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
170
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
173
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
2
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
174
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
7
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
175
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
176
Safety measurement cable 4mm, 50cm/20", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8L
6
Colour: black
Length: 50 cm
Wire cross section 2.5 mm2
ratings deliver: 600 V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
177
Safety measurement cable 4mm, 25cm/10", black, 600V CAT III ~1000V CAT II / 32A
SO5126-8B
3
colour: black
length: 25 cm / 10"
cable cross-section 2,5 mm2
ratings deliver: 600V CAT II, 32 A
Long life-span and ability of the contact component to withstand being plugged in and out many times with the
minimum of junction resistance
Plugs comply with the requirements of the standard IEC EN 61010-031
178
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Lucas Nülle GmbH Page 85/171 www.lucas-nuelle.us
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
179
Protected power distribution for working stations
ST8008-8N
1
400-V CEE distribution panel with automatic circuit breakers for attachment to profiles on experiment trolleys or direct
to table-top.
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
181
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
182
Display for Power Transmission equipment
ST8000-4L
1
183
Protection cover for three-level experiment trolleys
ST8010-9Y
1
In practice, medium-voltage and high-voltage networks are equipped with protective mechanisms connected via
current and voltage transformers.
In practice, medium-voltage and high-voltage networks are equipped with protective mechanisms connected via
current and voltage transformers.
Training contents
Training contents
The panel contains a digital, three-phase overcurrent time relay. An integrated program is responsible for a self-test
and the tripping test. The relay has three inverse current characteristics (normal, severely inverse and extremely
inverse). The relay parameters can be set manually or in conjunction with a PC.
Nominal frequency: 50 to 60 Hz
Output relay:
Switch-on current: 20A
Nominal current: 5A
Max. contact rating:
1250 VA/DC; 120W/DC, ohmic
500VA/AC; 75W/DC, inductive
Trip parameters:
I > 0.5-2x IN
I > 1-15x IN
tI > 0-100s
tI > 0-2.5s
LED indicators:
"ON" for ready
I> and I>> starting (flashing)
I> and I>> tripping (permanently On)
Controls:
"TEST" button to initiate the self-test
6 potentiometers for adjusting operate and trip times
8 DIP switches for adjusting the characteristics
Adjustments for time factors and nominal data
The integrated interface RS 485 is suitable for setting the relay parameters. It is also possible to store and
transmit measured relay values to and from the PC. Optical signal transmission guarantees galvanic isolation.
Weight: 1kg
185
Lucas Nülle GmbH Page 89/171 www.lucas-nuelle.us
Transmission line model 150km/300km (93.2miles/186.4miles)
CO3301-3A
1
Three-phase line simulation of a high voltage overhead power line with different lengths for measuring various
operational states (open-line, matched, short-circuit). Scale factor 1/1000 for current and voltage. Automatic
modification of wire length as soon as the corresponding overlay is in place.
Current: up to 2A
Weight: 6kg
186
Power switch module
CO3301-5P
2
187
Variable Ohmic load, three-phase, 1kW
CO3301-3F
1
Three synchronously adjustable circular rheostats with scale 100 - 0%, each with a fuse in the sliding-contact
connection.
Media:
Pos.
Product name
Bestell-Nr.
Anz.
188
Interactive Lab Assistant: Protective systems for high-voltage transmission line
SO2800-6L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Circuit diagrams
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
190
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
1
1x 1 m yellow
2x 2 m yellow
191
USB 2.0 Ethernet adapter, 10/100
LM8257
1
192
5-Port Ethernet Switch
LM9988
1
The USB-RS485 is a universal adapter of USB to RS485. This device is powered by the PC’s USB port. The USB-
RS485 adapter is identified by the PC as a serial interface and can be used as such.
Power supply:
Pos.
Product name
Bestell-Nr.
Anz.
194
Adjustable 3-phase power supply, 0-450V/2A
CO3301-3Z
1
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
195
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
197
Multi13S digital multimeter
LM2330
1
Universal precision lab multimeter and temperature meter with IR interface for high-quality, universal measurement
and testing in educational settings, power plants, process control installations etc.
198
Relay Test Unit
CO3301-5N
1
Testing device used to check current and voltage relays, time-delay and power relays. This tester is able to conduct 3-
phase relay testing.
Timer: 6 digit digital display, 0....999.999s (accuracy: +/- 0.02%; +2ms) Start/stop function via pushbutton
Graphic display
Contacts: 3 operating contacts, 2 auxiliary contacts (n.c./n.o. contactors): synchronous start output for external
equipment
Weight: 1.5 kg
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
200
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
201
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
202
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
203
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
205
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
206
Display for Power Transmission equipment
ST8000-4L
1
207
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
Training panel with digital overload and short-circuit protection for electrical machines and cables in meshed networks
(ANSI 50/ 51 and 67). The relay parameters can be set manually or in conjunction with a PC.
Un: 400V
Setting ranges:
I>: 0.5-2.0x IN/tI>: 0-100s
I>>: 1-15x IN/t>I>: 0-2.5s
Tripping characteristics:
- normal inverse
- very inverse
- extremely inverse
- independent
The integrated interface RS 485 is suitable for setting the relay parameters. It is also possible to store and
transmit measured relay values to and from the PC. Optical signal transmission guarantees galvanic isolation.
Weight: 1.8kg
Pos.
Product name
Bestell-Nr.
Anz.
209
Interactive Lab Assistant: Protective systems for high-voltage transmission line
SO2800-6L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Circuit diagrams
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
211
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
1
1x 1 m yellow
2x 2 m yellow
212
USB 2.0 Ethernet adapter, 10/100
LM8257
1
213
5-Port Ethernet Switch
LM9988
1
The USB-RS485 is a universal adapter of USB to RS485. This device is powered by the PC’s USB port. The USB-
RS485 adapter is identified by the PC as a serial interface and can be used as such.
Power supply:
Pos.
Product name
Bestell-Nr.
Anz.
215
Adjustable 3-phase power supply, 0-450V/2A
CO3301-3Z
1
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
216
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
218
Multi13S digital multimeter
LM2330
1
Universal precision lab multimeter and temperature meter with IR interface for high-quality, universal measurement
and testing in educational settings, power plants, process control installations etc.
219
Relay Test Unit
CO3301-5N
1
Testing device used to check current and voltage relays, time-delay and power relays. This tester is able to conduct 3-
phase relay testing.
Timer: 6 digit digital display, 0....999.999s (accuracy: +/- 0.02%; +2ms) Start/stop function via pushbutton
Graphic display
Contacts: 3 operating contacts, 2 auxiliary contacts (n.c./n.o. contactors): synchronous start output for external
equipment
Weight: 1.5 kg
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
221
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
222
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
223
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
224
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
226
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
227
Display for Power Transmission equipment
ST8000-4L
1
228
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
The training panel equipped with digital, over- and undervoltage relay (industrial model) is used to monitor single and
three-phase power systems (ANSI 27 und 59). The pick-up values and release times for initiating the over- and
undervoltage trip, are individually adjustable.
Pos.
Product name
Bestell-Nr.
Anz.
230
Interactive Lab Assistant: Protective systems for high-voltage transmission line
SO2800-6L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Circuit diagrams
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
232
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
1
1x 1 m yellow
2x 2 m yellow
233
USB 2.0 Ethernet adapter, 10/100
LM8257
1
234
5-Port Ethernet Switch
LM9988
1
The USB-RS485 is a universal adapter of USB to RS485. This device is powered by the PC’s USB port. The USB-
RS485 adapter is identified by the PC as a serial interface and can be used as such.
Power supply:
Pos.
Product name
Bestell-Nr.
Anz.
236
Adjustable 3-phase power supply, 0-450V/2A
CO3301-3Z
1
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
237
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
239
Multi13S digital multimeter
LM2330
1
Universal precision lab multimeter and temperature meter with IR interface for high-quality, universal measurement
and testing in educational settings, power plants, process control installations etc.
240
Relay Test Unit
CO3301-5N
1
Testing device used to check current and voltage relays, time-delay and power relays. This tester is able to conduct 3-
phase relay testing.
Timer: 6 digit digital display, 0....999.999s (accuracy: +/- 0.02%; +2ms) Start/stop function via pushbutton
Graphic display
Contacts: 3 operating contacts, 2 auxiliary contacts (n.c./n.o. contactors): synchronous start output for external
equipment
Weight: 1.5 kg
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
242
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
243
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
244
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
245
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
247
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
248
Display for Power Transmission equipment
ST8000-4L
1
249
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
The training panel contains a single-phase, directional power relay (ANSI 32 and 37). The unit also includes software
for self-testing. The relay parameters are set either manually or using a PC.
Power consumption:
- voltage circuit: 1VA
- current circuit: 0.075 VA at IN = 1A, 0.1VA at In= 5A
Output relay:
Switch-on current: 20A
Nominal current: 5A
Max. contact rating:
1250 VA/DC; 120W/DC, ohmic
500VA/AC; 75W/DC, inductive
Adjustment ranges:
PR > 1.... 30% PN
P> 1....120% PN
tPr 0....10s/0...100s
tP 0....10s/0...100s
Lucas Nülle GmbH Page 118/171 www.lucas-nuelle.us
LED indicators:
- "ON" = Ready
- P< and Pr> Starting (flashing)
- P> and Pr> Starting (permanently on)
Controls:
- "TEST" pushbutton = initiate self-test
- 6 potentiometers for adjusting trip range and switch off times
- 8 DIP switches for defining nominal values
The integrated interface RS 485 is suitable for setting the relay parameters. It is also possible to store and
transmit measured relay values to and from the PC. Optical signal transmission guarantees galvanic isolation.
Weight: 1.0 kg
Pos.
Product name
Bestell-Nr.
Anz.
251
Interactive Lab Assistant: Protective systems for high-voltage transmission line
SO2800-6L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Circuit diagrams
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
253
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
1
1x 1 m yellow
2x 2 m yellow
254
USB 2.0 Ethernet adapter, 10/100
LM8257
1
255
5-Port Ethernet Switch
LM9988
1
The USB-RS485 is a universal adapter of USB to RS485. This device is powered by the PC’s USB port. The USB-
RS485 adapter is identified by the PC as a serial interface and can be used as such.
Power supply:
Pos.
Product name
Bestell-Nr.
Anz.
257
Adjustable 3-phase power supply, 0-450V/2A
CO3301-3Z
1
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
258
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
260
Multi13S digital multimeter
LM2330
1
Universal precision lab multimeter and temperature meter with IR interface for high-quality, universal measurement
and testing in educational settings, power plants, process control installations etc.
261
Relay Test Unit
CO3301-5N
1
Testing device used to check current and voltage relays, time-delay and power relays. This tester is able to conduct 3-
phase relay testing.
Timer: 6 digit digital display, 0....999.999s (accuracy: +/- 0.02%; +2ms) Start/stop function via pushbutton
Graphic display
Contacts: 3 operating contacts, 2 auxiliary contacts (n.c./n.o. contactors): synchronous start output for external
equipment
Weight: 1.5 kg
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
263
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
264
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
265
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
266
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
268
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
269
Display for Power Transmission equipment
ST8000-4L
1
270
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
The training panel contains a digital three-phase relay for detecting earth-faults with isolated and low-resistance
earthed, primary distribution networks (ANSI 59N). The relay parameters can be set manually or in conjunction with a
PC.
Output relay:
Switch-on current: 20A
Nominal current: 5A
Max. contact rating:
1250 VA/DC; 120W/DC, ohmic
500VA/AC; 75W/DC, inductive
LED indicators:
"ON" ready
"Ue" starting (flashing); for release (permanently on)
Controls:
"TEST" button for testing the relay function and the LEDs
2 potentiometers for adjusting the release ranges
Ue > coarse and fine adjustments
1 potentiometer for adjusting the release times
DIP-switch for: NC, factor for Ue>, selection of the nominal frequency and adjustment of the hysteresis
The integrated interface RS 485 is suitable for setting the relay parameters. It is also possible to store and
transmit measured relay values to and from the PC. Optical signal transmission guarantees galvanic isolation.
Weight: 1kg
272
Voltage transformer, 3 phase
CO3301-4V
1
The three-phase transformer is suitable for use with protection relays and line simulations. The tertiary winding is
used for monitoring an earth short-circuit with an earth-fault relay.
Weight: 10kg
Pos.
Product name
Bestell-Nr.
Anz.
273
Interactive Lab Assistant: Protective systems for high-voltage transmission line
SO2800-6L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Circuit diagrams
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
275
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
1
1x 1 m yellow
2x 2 m yellow
276
USB 2.0 Ethernet adapter, 10/100
LM8257
1
277
5-Port Ethernet Switch
LM9988
1
The USB-RS485 is a universal adapter of USB to RS485. This device is powered by the PC’s USB port. The USB-
RS485 adapter is identified by the PC as a serial interface and can be used as such.
Power supply:
Pos.
Product name
Bestell-Nr.
Anz.
279
Adjustable 3-phase power supply, 0-450V/2A
CO3301-3Z
1
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
280
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
282
Multi13S digital multimeter
LM2330
1
Universal precision lab multimeter and temperature meter with IR interface for high-quality, universal measurement
and testing in educational settings, power plants, process control installations etc.
283
Relay Test Unit
CO3301-5N
1
Testing device used to check current and voltage relays, time-delay and power relays. This tester is able to conduct 3-
phase relay testing.
Timer: 6 digit digital display, 0....999.999s (accuracy: +/- 0.02%; +2ms) Start/stop function via pushbutton
Graphic display
Contacts: 3 operating contacts, 2 auxiliary contacts (n.c./n.o. contactors): synchronous start output for external
equipment
Weight: 1.5 kg
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
285
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
286
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
287
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
288
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
290
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
291
Display for Power Transmission equipment
ST8000-4L
1
292
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
Pos.
Product name
Bestell-Nr.
Anz.
293
Time Overcurrent Relay
CO3301-4J
1
The panel contains a digital, three-phase overcurrent time relay. An integrated program is responsible for a self-test
and the tripping test. The relay has three inverse current characteristics (normal, severely inverse and extremely
inverse). The relay parameters can be set manually or in conjunction with a PC.
Nominal frequency: 50 to 60 Hz
Output relay:
Switch-on current: 20A
Nominal current: 5A
Max. contact rating:
1250 VA/DC; 120W/DC, ohmic
500VA/AC; 75W/DC, inductive
Trip parameters:
I > 0.5-2x IN
I > 1-15x IN
tI > 0-100s
tI > 0-2.5s
LED indicators:
"ON" for ready
I> and I>> starting (flashing)
I> and I>> tripping (permanently On)
Controls:
"TEST" button to initiate the self-test
6 potentiometers for adjusting operate and trip times
8 DIP switches for adjusting the characteristics
Adjustments for time factors and nominal data
The integrated interface RS 485 is suitable for setting the relay parameters. It is also possible to store and
transmit measured relay values to and from the PC. Optical signal transmission guarantees galvanic isolation.
Weight: 1kg
Training panel with digital overload and short-circuit protection for electrical machines and cables in meshed networks
(ANSI 50/ 51 and 67). The relay parameters can be set manually or in conjunction with a PC.
Un: 400V
Setting ranges:
I>: 0.5-2.0x IN/tI>: 0-100s
I>>: 1-15x IN/t>I>: 0-2.5s
Tripping characteristics:
- normal inverse
- very inverse
- extremely inverse
- independent
The integrated interface RS 485 is suitable for setting the relay parameters. It is also possible to store and
transmit measured relay values to and from the PC. Optical signal transmission guarantees galvanic isolation.
Weight: 1.8kg
295
Transmission line model 150km/300km (93.2miles/186.4miles)
CO3301-3A
1
Three-phase line simulation of a high voltage overhead power line with different lengths for measuring various
operational states (open-line, matched, short-circuit). Scale factor 1/1000 for current and voltage. Automatic
modification of wire length as soon as the corresponding overlay is in place.
Current: up to 2A
296
Power switch module
CO3301-5P
2
Accessories:
Pos.
Product name
Bestell-Nr.
Anz.
297
Connection plugs for PROFIBUS with PG socket and terminating resistor
LM9182
5
With integrated PG socket for connecting PC/PG without need for any extra installations plus integrated combination
of resistors with slide switches for isolating functionality. Includes Fast-Connect connector using crimp terminals with
90° terminal outlets.
298
Connection cable for PROFIBUS, per metre
LM9181
10
299
Wire stripper for PROFIBUS cables
LM9184
1
For quick and easy connection of PROFIBUS plugs to PROFIBUS bus lines
Pos.
Product name
Bestell-Nr.
Anz.
300
Interactive Lab Assistant: Protective systems for high-voltage transmission line
SO2800-6L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Circuit diagrams
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
302
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
1
1x 1 m yellow
2x 2 m yellow
303
USB 2.0 Ethernet adapter, 10/100
LM8257
1
304
5-Port Ethernet Switch
LM9988
1
The USB-RS485 is a universal adapter of USB to RS485. This device is powered by the PC’s USB port. The USB-
RS485 adapter is identified by the PC as a serial interface and can be used as such.
Power supply:
Pos.
Product name
Bestell-Nr.
Anz.
306
Adjustable 3-phase power supply, 0-450V/2A
CO3301-3Z
1
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
307
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
309
Multi13S digital multimeter
LM2330
1
Universal precision lab multimeter and temperature meter with IR interface for high-quality, universal measurement
and testing in educational settings, power plants, process control installations etc.
310
Relay Test Unit
CO3301-5N
1
Testing device used to check current and voltage relays, time-delay and power relays. This tester is able to conduct 3-
phase relay testing.
Timer: 6 digit digital display, 0....999.999s (accuracy: +/- 0.02%; +2ms) Start/stop function via pushbutton
Graphic display
Contacts: 3 operating contacts, 2 auxiliary contacts (n.c./n.o. contactors): synchronous start output for external
equipment
Weight: 1.5 kg
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
312
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
313
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
314
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
315
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
317
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
318
Display for Power Transmission equipment
ST8000-4L
1
319
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Training contents:
Training contents:
- Distance protection
- Voltage protection
High-speed distance protection is used for selective short-circuit protection in high voltage systems. In conjunction
with transmission line simulation lines, all relevant situations can be simulated.
Functions:
In- Outputs:
5 Indication inputs
4 command outputs
5 fast relays
Measuring valves:
Current
Voltage
cos φ
active and reactive power
Technical data:
Weight: 5kg
321
Voltage transformer, 3 phase
CO3301-4V
1
The three-phase transformer is suitable for use with protection relays and line simulations. The tertiary winding is
used for monitoring an earth short-circuit with an earth-fault relay.
Weight: 10kg
Accuracy: class 1
Overcurrent factor: FS 10
Weight: 6kg
323
Transmission line model 150km/300km (93.2miles/186.4miles)
CO3301-3A
1
Three-phase line simulation of a high voltage overhead power line with different lengths for measuring various
operational states (open-line, matched, short-circuit). Scale factor 1/1000 for current and voltage. Automatic
modification of wire length as soon as the corresponding overlay is in place.
Current: up to 2A
Weight: 6kg
Pos.
Product name
Bestell-Nr.
Anz.
324
Interactive Lab Assistant: Protective systems for high-voltage transmission line
SO2800-6L
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern energy systems. The fundamentals are conveyed using easy to understand
animations. The Interactive Lab Assistant in conjunction with the SCADA Viewer constitutes a comfortable
experimenting environment.
Special features:
Measured values and diagrams can be stored in the experiment instructions per drag and drop
The SCADA Viewer can be started directly from the experiment instructions
Includes questions with feedback and evaluation logic for progress monitoring
Documents can be printed out for hardcopy of experiment instructions including solutions
Training contents:
Circuit diagrams
The 'SCADA Viewer' is a software program used for the control and monitoring of power engineering systems. With
the software it is possible to display all measured values and operating states inside the system in real time on the
existing measuring instruments. Important parameters and signals can be controlled by the software.
The measured values and operating states of the equipment can be selected, recorded and plotted over time,
evaluated and then exported.
Using the 'SCADA Viewer' projects in power engineering are not only made transparent but readable.
Software functions:
326
Patch cable Cat5E 1x 1 m yellow, 2x 2 m yellow
LM9057
1
1x 1 m yellow
2x 2 m yellow
327
USB 2.0 Ethernet adapter, 10/100
LM8257
1
328
5-Port Ethernet Switch
LM9988
1
The USB-RS485 is a universal adapter of USB to RS485. This device is powered by the PC’s USB port. The USB-
RS485 adapter is identified by the PC as a serial interface and can be used as such.
Power supply:
Pos.
Product name
Bestell-Nr.
Anz.
330
Adjustable 3-phase power supply, 0-450V/2A
CO3301-3Z
1
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
331
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
2
The three-phase measuring instrument permits the measurement and display of relevant power network parameters.
It is able to measure single, two-phase or three-phase measurements. The display and operation is carried out by
means of menu navigation with an LC display or the integrated Ethernet interface. The optional SCADA software
provides for the display of all measurements and allows the implementation and analysis of intelligent networks (smart
grids). The “smart meter” acts as a digital electricity meter where end customers are connected to the grid in order to
measure electricity consumption and can be used to turn consumers on or off depending on the circumstances.
Fault tolerances:
333
Multi13S digital multimeter
LM2330
1
Universal precision lab multimeter and temperature meter with IR interface for high-quality, universal measurement
and testing in educational settings, power plants, process control installations etc.
334
Relay Test Unit
CO3301-5N
1
Testing device used to check current and voltage relays, time-delay and power relays. This tester is able to conduct 3-
phase relay testing.
Timer: 6 digit digital display, 0....999.999s (accuracy: +/- 0.02%; +2ms) Start/stop function via pushbutton
Graphic display
Contacts: 3 operating contacts, 2 auxiliary contacts (n.c./n.o. contactors): synchronous start output for external
equipment
Weight: 1.5 kg
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
336
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
337
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
10
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
338
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
339
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
With 3 screw-on rubber stoppers, dimensions 65x65x114 mm approx. (top fixing for PC)
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
341
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
342
Display for Power Transmission equipment
ST8000-4L
1
343
Protection cover for three-level experiment trolleys
ST8010-9Y
1
Sustainable energy transmission for efficient and reliable grids in the future
Sustainable energy transmission for efficient and reliable grids in the future
High-voltage DC transmission is a method for transmitting electrical energy by means of high DC voltage.
This technique is intended for the long-distance bulk transmission of energy via DC, since above certain distances
HVDC exhibits a lower degree of loss overall than is the case for conventional transmission using three-phase AC
power, in spite of the increased converter losses.
High-voltage DC transmission is frequently used for energy transmission over comparatively short distances as well if
the electrical transmission line has been designed with a high degree of capacitance. This is the case with maritime
cabling but also buried terrestrial lines.
One other application is for an intermediate coupling link between networks, which allows for direct exchange of
electrical energy between three-phase power networks.
Training contents:
A high-voltage DC (HVDC) transmission line essentially consists of an connverter station, which converts AC voltage
from a conventional electricity grid into DC voltage, a transmission line and another converter station at the opposite
end of the line, which converts the DC voltage back into an AC voltage. This allows energy to be transported in both
directions. It is always necessary to have two converter stations in order to operate this system.
Operating modes:
Control of active power in both directions
STATCOM mode
Coupling to the power grid at various frequencies
“Fault ride-through” support
Generation of AC voltages with minimal harmonics by means of IGBT converters
Automatic control of reactive and active power, frequency and voltage
Transmission of up to 1 kW active power
Provision of up to 1 kVAR reactive power
DC link circuit voltage adjustable up to 750 V DC
Built-in power switch for switching into the grid
USB port
Built-in brake chopper
Supply voltage: 3 x 400 V, 50...60 Hz
Dimensions: 297 x 460 x 210 mm (HxWxD)
345
HVDC Converter Station 2
CO3301-6E
1
A high-voltage DC (HVDC) transmission line essentially consists of an converter station, which converts AC voltage
from a conventional electricity grid into DC voltage, a transmission line and another converter station at the opposite
end of the line, which converts the DC voltage back into an AC voltage. This allows energy to be transported in both
directions. It is always necessary to have two converter stations in order to operate this system.
Operating modes:
Control of active power in both directions
STATCOM mode
Integration of synchronous generators, wind turbines and various loads
Coupling to the power grid at various frequencies
“Fault ride-through” support
Generation of AC voltages with minimal harmonics by means of IGBT converters
Automatic control of reactive and active power, frequency and voltage
Transmission of up to 1 kW active power
Provision of up to 1 kVAR reactive power
DC link circuit voltage adjustable up to 750 V DC
Built-in power switch for switching into the grid
USB port
Built-in brake chopper
Supply voltage: 3 x 400 V, 50...60 Hz
Dimensions: 297 x 460 x 210 mm (HxWxD)
High-voltage direct current line simulation with a scale factor 1/1000 for current and voltage.
Voltage: 700VDC
Current: 2A
347
Variable Ohmic load, three-phase, 1kW
CO3301-3F
1
Three synchronously adjustable circular rheostats with scale 100 - 0%, each with a fuse in the sliding-contact
connection.
Modern wind turbines or photovoltaic power inverters are required nowadays to respond to faults in the electrical
power grid without simply shutting down. Such a response is called "fault ride-through". The dynamic grid fault
simulator emulates such faults in the electricity grid. This makes it possible to investigate the response of any
equipment connected downstream from the fault.
Pos.
Product name
Bestell-Nr.
Anz.
349
Interactive Lab Assistant: High Voltage DC Transmission (HVDC)
SO2800-3K
1
The experiment instructions come in the form of an Interactive Lab Assistant course. This multimedia course is a step-
by-step guide through the topic of modern photovoltaic energy systems. The physical fundamentals are conveyed
using easy to understand animations. The Interactive Lab Assistant in conjunction with the virtual instruments
constitutes a comfortable experimenting environment.
Special features:
Training contents:
Controllable 3-phase power supply unit 0...255/450V for continuous 3-phase supply
351
Three-phase supply for electrical machines
CO3212-5V
1
Power supply for AC and three-phase. The supply is specially designed for use with electrical machines.
Outputs:
Three phase: L1, L2, L3, N from 4 mm safety sockets
Protective systems:
Motor protection switch adjustable from 6.3...16A
Under voltage trip
Safety cut-out
Power connection: 3x 230/400V, 50/60Hz via CEE plug with 1.8m power lead
Dimensions: 297 x 114 x 140mm (HxWxD)
Weight: 2kg
352
Multiple socket outlet, 6 fold, with illuminated switch
ST8010-4J
1
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour black
354
Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5126-3V
5
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour blue
355
Safety connecting plug 4mm with tap (2x), red, 1000V/32A CAT II
SO5126-3U
5
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour red
356
Safety connecting plug 4mm with tap (2x), gr/ye, 1000V/32A CAT II
SO5126-3W
8
Moulded insulation
both sides with touch protection (safety plug + safety sockets), distance 19 mm
transition resistance max. 6 mΩ
rated data: 1000 V / 32 A CAT II
colour green/yellow
357
Lucas Nülle GmbH Page 168/171 www.lucas-nuelle.us
Set of safety measurement cables, 4mm, 31 pcs
SO5148-1L
1
Safety measurement cables with 4mm safety plugs, coloured, PVC insulation, highly flexible
358
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
ST7200-4C
1
High-quality mobile experiment and demonstration trolley from the SybaPro range featuring aluminium table legs and
low-level shelf.
This trolley is suitable for mounting under-table cabinets and is compatible with all add-ons and extensions in the
SybaPro range.
It is supplied with one shelf, an angle bracket for attaching a PC and a cable holder.
30-mm table top made of highly compressed, multi-layer fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific points such as by soldering tips or cigarette ends
Frame with solid impact-resistant protective edging made of 3 mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Power strip with 6 outlet sockets mounted underneath the table top, lead and earthed plug
Frame:
Cable holder:
Width 200 mm with 12 cable slots to accommodate 48 x 4-mm safety measurement leads
PC attachment bracket:
> The height of the cable holder and PC attachment bracket can be adjusted along the aluminium profiles
> For attachment to left or right, fastening materials included
> Acid-resistant epoxy-resin powder coating of thickness 80 µm approx., colour RAL 7047
Dimensions:
359
Protected power distribution for working stations
ST8008-8N
1
400-V CEE distribution panel with automatic circuit breakers for attachment to profiles on experiment trolleys or direct
to table-top.
Additionally recommended:
Pos.
Product name
Bestell-Nr.
Anz.
360
Keyboard adapter for flat screen monitor holders
ST8010-4G
1
Keyboard adapter for use in combination with flat screen monitor holders
361
Monitor holder for flat screen monitor of weight up to 15kg/33lbs
ST8010-4T
1
Pivoting monitor holder with two-part joint for attachment to aluminum profiles.
362
Display for HVDC equipment
ST8000-4M
1
363
Protection cover for three-level experiment trolleys
ST8010-9Y
1