Professional Documents
Culture Documents
Al Rayyan Techncial
Al Rayyan Techncial
=:,µ1,
A l Ra yy n Nursery Compa n
a
y 2053029968 -:., .._,.,
C. r 2053 0 2 9 6 8
A�AYYAN
n.1 c- TuJ I c-·.Jt.,1JI ( l.a11
.1.l o (1. '\ J..11H
MATERIAL SUBMITTAL
ww w.alrayyanksa.com � mily.compa
@ A lhu a ny@gma il.c om � lnfo@alrayyanksa.
□ □
co m
+966S61603388 +966S499929
99 0
@,!µILII l)lµn.b..11 ..w..;>JI 19,!.J,b- ,olo ::LII
TABLE OF CONTENTS
1- LANDSCAPE
2- Products Data Sheets
3- Irrigation material Specification
Ficus microcarpa
GRASS
BERMUDA TURFGRASS PASPALUM VAGINATUM (C2000)
SOD
A. Turfgrass Seed and Sod: Number 1 Quality/Premium,
including limitations on thatch, weeds, diseases, nematodes, and
insects, complying with "Specifications for Turfgrass Sod and Seed
Materials" in TPI's "Guideline Specifications to Turfgrass
Sodding." Furnish viable sod of uniform density, color, and texture,
strongly rooted, and capable of vigorous growth and development when
planted.
B. Turfgrass Species: Sod of Grass Species as follows:
1. Determine if a single grass species or mixture of two or more
grass species is required. Turfgrass sod grown from a warm-
season, single-species grass predominates in the North and northern
transition zones. Consult university cooperative extension service
or country extension agency for current recommendations Revise
description and insert proprietary seed mixes if preferred. Indicate,
here or on Drawings, areas of full sun, sun and partial shade, and
shade.
2. Full Sun: Paspalum Vaginatum
√
1
The first paper in the (MAR) contains the name of the supplier, the name of the manufacturer,
the name of the product, the name of the project, the name of consultant and the name of
the contractor.
2 The format for the compliance sheets in the file is the same as approved
by the consultant. √
√
3
All the contents of the specifications of the project related to the materials to be approved are
included in the compliance sheets.
4 The specifications of the materials to be approved are mentioned in
proposed specification. √
√
5
All compliance sheets signed and stamped by the manufacturer and supplier.
√
8 The (MAR) contains material test certificates.
√
9 The (MAR) contains sample board and original catalogue.
√
10 The (MAR) contains SASO certificates and should be valid.
MATERIAL LIST
IRRIGATION EQUIPMENT AND ACCESSORIES
info@alrayyanksa.com
24
info@wise-engg.com
FLOWFLEX COMPONENTS LTD
BUXTON, SK17 7LR, UNITED KINGDOM +44 (0) 1298 77211 hello@flowflex.com
www.flowflex.com
info@wise-engg.com
L198 Data Sheet
Product Sizes
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
QUICK COUPLERS
The sturdy red brass and stainless steel construction of Quick Couplers
strengthens any project.
KEY BENEFITS
• 100% interchangeable with major brands
• Red brass and stainless steel construction
• Heavy-duty thermoplastic locking and non-locking covers
• Optional winged stabilization and Acme key connection
• Stainless steel lug on 1" and 1¼" keys
• Spring-loaded covers with stainless steel springs
for positive closing and protection of valve’s
Quick Coupler
sealing components
• Warranty period: 5 years
• See the SnapLok combo kit
Notes:
* All locking cover models are available with purple covers for reclaimed water applications.
** Anti-rotation stabilization wings.
HQ-44-LRC-AW-R HK-44A
info@alrayyanksa.com
Visit hunterindustries.com
Commited to Your Success… All The Way!
Model:
Features:
- All parts of the air release valve are made of corrosion resistant fiberglass reinforced UV
protected nylon
- Release large quantities of air through an opening equal to a large size standard vent.
- It remains open even when the pressure reaches 10 PSI.
- During normal flow, while the line is under pressure, the valves remain closed
- Maximum working pressure is
Product brochure.
info@alrayyanksa.com
AV10
KINETIC / VACUUM
BREAKING AIR VALVE
The AV-010 Air & Vacuum Valve discharges air at
high flow rates during the filling of the system and
admits air at high flow rates during drainage ,
pump shut-off or at water column separation.
Reliable Simple
Installations Maintanance
3
14", 1" MODEL 2" MODEL
1"
&
3
14" (20MM) 0.1 BUNA-N
3
14", 1" MODEL 2" MODEL
3"
HEAD LOSS
AIR & VACUUM FLOW RATE
0.6
CATALOG NUMBERS
0.4
Differencial Pressure
0.2
AV10
0
-0.2
-0.4
-600
-400
Flow Rate
MODEL DIAMETER
BSP
BSP
CONNECTION MAX. PRESSURE CATALOG NUMBER
info@alrayyanksa.com
ICV
This dependable valve works seamlessly with highly demanding systems.
KEY BENEFITS
• Optional Filter Sentry® Mechanism scours the filter screen in dirty
water conditions
• External/internal manual bleed allows for quick and
easy activation at the valve
• Glass-filled nylon construction provides high pressure rating and
reliability
• Double-beaded diaphragm seal design ensures leak-free performance
• Fabric-reinforced EPDM diaphragm and seat ensure ICV-151G
greater performance in all water conditions ICV-101G Inlet diameter: 1½"
Inlet diameter: 1" Height: 7⅛"
• Captive bonnet screws eliminate the possibility of lost Height: 5½" Length: 6⅞"
parts during disassembly Length: 4¾" Width: 5½"
• Triple-tool bonnet screws are compatible with standard Width: 4"
or Phillips screwdrivers as well as a nut driver
• Encapsulated solenoid with captive plunger used on
every Hunter valve provides hassle-free service
• Flow control maximizes efficiency and prolongs the life of the system
USER-INSTALLED OPTIONS
• Accu Sync® Pressure Regulator at the valve
• DC-Latching Solenoid for battery-operated controllers (P/N 458200)
• Filter Sentry easily added to an installed valve*
• Solenoid conduit cover (P/N 464322)
ICV-201G ICV-301
FACTORY-INSTALLED OPTIONS Inlet diameter: 2" Inlet diameter: 3"
• LS: Valve without solenoid Height: 7⅛" Height: 10¾"
Length: 6⅞" Length: 9"
• DC: DC-Latching Solenoid for battery-operated controllers
Width: 5½" Width: 7⅜"
• FS: Filter Sentry
• FS-R: Reclaimed option with Filter Sentry, purple control
knob, and purple chlorine-resistant diaphragm
OPERATING SPECIFICATIONS
• Flow:
- ICV-101G: 0.1 to 40 GPM
- ICV-151G: 0.1 to 150 GPM
- ICV-201G: 0.1 to 200 GPM
- ICV-301: 0.1 to 300 GPM ICV-R
• Recommended pressure range: 20 to 220 PSI Inlet diameter: 1", 1½", 2",
• Temperature rating: 150°F and 3"
Height: 7⅛"
• Warranty period: 5 years Length: 6⅞"
Width: 5½"
SOLENOID SPECIFICATIONS
• 24 VAC solenoid
- 350 mA inrush, 190 mA holding, 60 Hz
- 370 mA inrush, 210 mA holding, 50 Hz
info@alrayyanksa.com
ICV 1", 11/ 2", 2", & 3" – SPECIFICATION BUILDER: ORDER 1 + 2 + 3 + 4
ICV-101G = Globe valve with flow control (blank) = No option AS-ADJ = Adjustable Accu
1" ICV-151G = Sync Pressure Regulator
FS = Filter Sentry
1½" ICV-
458200 = DC-Latching Solenoid
201G = 2" FS-R = Filter Sentry purple reclaimed
for battery-operated controllers
diaphragm and ID tag
ICV-301 = 3" Globe / Angle valve with flow control
561205 = Reclaimed flow
DC = DC-Latching Solenoid for battery- control handle andle (1", 11/ 2", 2" only)
operated controllers
LIT-700 = Reclaimed ID tag
LS = Less solenoid
Example:
ICV-201G-AS-ADJ = 2" ICV globe valve with flow control, user-installed adjustable Accu Sync Pressure Regulator
info@alrayyanksa.com
1" PGV AND PGV JAR-TOP
These versatile and robust valves offer simple serviceability.
KEY BENEFITS
• External/internal manual bleed allows for quick and
easy activation at the valve
• Double-beaded diaphragm seal design ensures leak-free
performance
• Captive bonnet screws eliminate the possibility of lost
parts during disassembly
• Triple-tool bonnet screws are compatible with standard
or Phillips screwdrivers as well as a nut driver
• Jar-top models provide easy access without tools
• Encapsulated solenoid with captive plunger used on
every Hunter valve provides hassle-free service
• Flow control maximizes efficiency and prolongs the life of the PGV-101G
system PGV-100G Inlet diameter: 1"
Inlet diameter: 1" Height: 5"
Height: 5" Length: 4½"
USER-INSTALLED OPTIONS Length: 4½" Width: 2½"
• Accu Sync® Pressure Regulator at the valve* Width: 2½"
• DC-Latching Solenoid for battery-operated controllers (P/N
458200)
• Solenoid conduit cover (P/N 464322)
FACTORY-INSTALLED OPTIONS
• LS: Valve without solenoid
• DC: DC-Latching Solenoid for battery-operated controllers
• JT: Jar-top models
OPERATING SPECIFICATIONS
• Flow: 0.2 to 40 GPM
PGV-100JT-G
• Recommended pressure range: 20 to 150 PSI Inlet diameter: 1"
• Temperature rating: 150°F Height: 5½"
• Warranty period: 2 years Length: 4½"
Width: 3¼"
SOLENOID SPECIFICATIONS
•
350 mA inrush, 190 mA holding, 60 Hz
370 mA inrush, 210 mA holding, 50 Hz
info@alrayyanksa.com
1
Example:
PGV-101-MM = 1" PGV globe valve, with flow control, with male NPT inlet and outlet
PGV-100-JT = Globe valve, without flow control, G = Female threaded inlet/ DC = DC-Latching Solenoid for AS-ADJ = Adjustable Accu Sync
1" threaded inlet/outlet outlet battery-operated controllers Pressure Regulator
Globe valve, with flow control, G-S = Slip inlet /outlet LS = Less solenoid 458200 = DC-Latching Solenoid for
PGV-101-JT = threaded inlet/outlet battery-operated controllers
1"
MB = Male NPT inlet/1" poly 269205 = Reclaimed flow control handle
barb outlet
Example:
PGV-101-JT-MM = 1" PGV globe valve, with jar-top bonnet, with flow control, with male NPT inlet and outlet
PGV-100G Installed
Male x Male
10
15
10 10
14 18 16
info@alrayyanksa.com
Subject: irrigation material submittal
info@alrayyanksa.com
info@alrayyanksa.com
Packaging dimensions - Dimensiones emba/aje - Dimensions emballage 3/4" 1" 1" 1/2 1" 1/2 L 2"
L 49cm
w 37cm
H 51cm
Unites per box - Unidades porcaja- Unites par boite 60 60 25 13 13
-
r 0.5 ,----------------,------ --------- --;
,
z
i7
0 l;f .. ..t'
)V 1---------+----.:,;,--;-----1 ---1--+--+--- " r l l - i---...-!
w 1,;; -
1------+----+--E-�--+--+-+-- E j
cc:
E';,
<: ti: Q. Q. Q. Q.
' -'2
Q
l::J ru
cCl.. 8
w
a: _ _ _ _/ - --+---+---1--1--+-I
:::
l
V
l
V
>w
c..
[ (m3/h) - DEBIT
FLOW - CAUDAL
Polfgono La Armentera.
Parcela 87 22400
MONZON. Huesca
(Spain) Tel.: (+34) 974
401 933
AENOR
Gesti6n
...
[ CLEAN WATER OUTLET
SALIDA AGUA LIMP/A •
SORTIE D'EAU FILTRtE]
matholding gruup
info@wise-engg.com
Subject: irrigation material submittal
info@alrayyanksa.com
info@alrayyanksa.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
Rad
Flow
KEY BENEFITS
• Three types of nozzles available for various
landscapes: standard red, standard blue, gray low-
angle
• Adjustable arc from 40° to 360° to keep water in the appropriate
areas
• Factory-installed rubber cover for safety
• Through-the-top arc adjustment for easy installation
• QuickCheck™ Arc Mechanism for fast arc adjustment
PGP-ADJ
OPERATING SPECIFICATIONS Overall height: 7⅜"
• Nozzle choices: 27 Pop-up height: 4"
Exposed diameter: 1¾"
• Radius: 22' to 52'
Inlet size: ¾"
• Flow: 0.5 to 14.1 GPM
• Recommended pressure range: 25 to 70 PSI
• Operating pressure range: 20 to 100 PSI
• Precipitation rate: 0.4 in/hr approximately
• Nozzle trajectory: standard = 25°, low-angle = 13°
• Warranty period: 2 years
FACTORY-INSTALLED OPTIONS
• Red #5–#8 Nozzle; Blue #1.5– Nozzle Pressure Radius Flow Precip in/hr
4.0
PSI ft. GPM
USER-INSTALLED OPTIONS 30 22 1.4 0.56 0.64
• Drain Check Valve (up to 3' of elevation) (P/N 142300SP) 4LA 40 24 1.7 0.57 0.66
Gray 50 26 1.8 0.51 0.59
60 28 2.0 0.49 0.57
30 25 1.6 0.49 0.57
1
5LA 40 27 1.9 0.50 0.58
Standard Features 3 Feature Options Gray 50 28 2.1 0.52 0.60
60 30 2.3 0.49 0.57
Adjustable arc with blue 1.5 to 4.0 = Factory-installed
nozzle rack 30 27 2.1 0.55 0.64
6LA 40 30 2.5 0.53 0.62
Adjustable arc with red #5 to #8 = Factory-installed
nozzle rack red nozzle number Gray 50 33 2.8 0.49 0.57
60 35 3.0 0.47 0.54
Examples: 30 29 2.8 0.64 0.74
PGP-ADJ = 4" pop-up, adjustable arc 7LA 40 32 3.1 0.58 0.67
PGP-ADJ-B-3.0 = 4" pop-up, adjustable arc, and 3.0 blue nozzle
Gray 50 35 3.5 0.55 0.64
PGP-ADJ-07 = 4" pop-up, adjustable arc, and #7 red nozzle
60 37 3.8 0.53 0.62
30 31 3.4 0.68 0.79
PGP Red Standard Nozzle 8LA 40 34 3.9 0.65 0.75
Gray 50 37 4.4 0.62 0.71
60 38 4.7 0.63 0.72
30 33 4.3 0.76 0.88
9LA 40 37 5.0 0.70 0.81
info@wise-engg.com
Nozzle Pressure Radius Flow Precip in/hr Nozzle Pressure Radius Flow Precip in/hr
PSI ft. GPM PSI ft. GPM
0.12 0.14 1.2
0.14 0.16 31 1.4 Red (P/N 130900)
Red Blue 31 1.5
1.8
30 29 0.7 0.16 0.19 1.9
2 40 30 0.8 0.17 0.20 25 33 1.4 0.25 0.29
Red 50 30 0.9 0.19 0.22 2.0 35 33 1.7 0.30 0.35
Blue (P/N 665300)
60 31 1.0 0.20 0.23 Blue 45 34 2.0 0.33 0.38
55 34 2.1 0.35 0.40
3 31 1.0 65 34 2.3 0.43 0.50
Red 31 1.2 Gray (P/N 233200)
1.3 2.5
Blue
30 32 1.2 0.23 0.26
4 40 33 1.4 0.25 0.29
Red 50 34 1.6 0.27 0.31
60 34 1.8 0.30 0.35 25 35 2.2 0.35 0.40
1.6 3.0 35 36 2.7 0.40 0.46
5 1.8 Blue 45 38 3.0 0.40 0.46
Red 55 39 3.4 0.43 0.50
65 39 3.7 0.47 0.54
30 34 2.0 0.33 0.38
6 40 36 2.4 0.36 0.41
Red 50 38 2.7 0.36 0.42 Blue
60 38 2.9 0.39 0.45 41
41
7 25 37 3.7 0.52 0.60
Red 5.0 35 39 4.5 0.57 0.66
Blue 45 42 5.0 0.55 0.63
30 37 3.2 0.45 0.52 55 42 5.7 0.62 0.72
40 39 3.7 0.47 0.54 65 42 6.2 0.68 0.78
Red 50 41 3.9 0.45 0.52
60 42 4.6 0.50 0.58
Blue
41
Red
5.5 25 37 6.0 0.84 0.97
40 44 6.0 0.60 0.69 8.0 35 41 7.0 0.80 0.93
10 50 46 6.8 0.62 0.71 Blue 45 44 8.0 0.80 0.92
Red 60 47 7.6 0.66 0.76 55 46 9.0 0.82 0.95
70 49 8.2 0.66 0.76 65 46 9.8 0.89 1.03
Red
51 10.5
40 46 10.5 0.96 1.10
50 48 11.9 0.99 1.15
Red 60 50 12.7 0.98 1.13
70 52 14.1 1.00 1.16
PGP-ADJ
Bold = Recommended pressure
Easy arc and radius adjustment
Note:
All precipitation rates calculated for 180° operation. For the
precipitation rate for a 360° sprinkler, divide by 2.
info@alrayyanksa.com
Subject: irrigation material submittal
info@alrayyanksa.com
Built on Innovation®
hunter.info/WAND
unlimited numbe
X2™ CONTROLLER of controllers,
receive instant
The versatile X2 Controller delivers highly efficient and reliable automatic status updates,
irrigation for residential and light commercial applications. The simple, plug-in and get system
WAND Module enables smart irrigation management with Hydrawise Software alerts via
for remote access and programming. Hydrawise
Software.
WAND offers the latest wireless Bluetooth® Technology, so you can operate
the system remotely with your smartphone. Developed with professional
contractors in mind, this capability lets you easily install the X2 Controller
using the Hydrawise App if Wi-Fi is unavailable. It also allows you to access the
controller when it’s in a hard-to-reach location or you want to maintain distance
for security or health reasons. Learn more. Visit
hunterindustries
The X2 Controller is the ideal tool for maintaining healthy landscapes and saving com or contact
water. Once online, you’ll save time with preprogrammed irrigation schedules your local Sales
that you can send to multiple controllers in seconds. You can also manage an Manager.
info@alrayyanksa.com
Speed up maintenance Control X2 remotely with ROAM (1,000') or
ROAM XL (2 miles).
info@alrayyanksa.com
X2 FEATURES & SPECIFICATIONS
• Wi-Fi capable managed by Hydrawise Software • Provides online irrigation management with
• 3 flexible programs with 4 start times each with run controller status and faulty wiring alerts
times up to 6 hours • Increased programming with 6 start times with run
• Backlit display provides optimal visibility in any setting times up to 24 hours
• Compliant junction box allows connection with 110 • Predictive Watering® provides precise
and 220 V power supplies weather adjustments for maximum water
savings
• QuickCheck™ Technology provides simple
diagnostics of faulty field wiring • Compatibility with Amazon Alexa™ and
Control4® home automation
• Hide Programs option displays one program and one
start time for simplification • Bluetooth pairing makes connecting to Wi-Fi
faster and easier
• Suspend irrigation for up to 99 days during the off
season • Use your smartphone as a manual remote when Wi-
• Short-circuit protection detects wiring faults and Fi is unavailable or controller is hard to access
skips the station without system damage • Copy and paste Hydrawise Software scheduling to
• Easy Retrieve® Memory backs up the any X2 Controller for full schedule setup in
full irrigation schedule seconds with Rapid Programming Technology
• Delay Between Stations for slow-closing • Warranty period: 2 years
valves or pump recharge
Model
• Cycle and Soak prevents water waste and runoff in
areas with elevation changes or tight soils
X2
• Seasonal adjustment for quicker schedule
Plastic, IP44
adjustments without changing run times
• Warranty period: 2 years
Height: 9"
Width: 7½"
Depth: 3⅞"
Model Description
Amazon Alexa is a trademark of Amazon.com Inc. or its affiliates. Control4 is a EPA WATERSENSE APPROVED
registered trademark of Control4 Corporation in the United States and/or other Recognized as a responsible water-saving tool by the
countries. The Bluetooth® word mark and logos are registered trademarks owned by U.S. Environmental Protection Agency
Bluetooth SIG Inc. and any use of such marks by Hunter Industries is under license. when installed with the WAND module.
info@alrayyanksa.com
Website hunterindustries.com | Customer Support 1-800-383-4747 | Technical Service 1-800-733-2823
Helping our customers succeed is what drives us. While our passion for innovation and engineering
is built into everything we our
info@wise-engg.com
info@wise-engg.com
Subject: irrigation material submittal
info@alrayyanksa.com
MESC
Irrigation Control Wire
UF Direct Burial
CONDUCTOR:
Solid / Stranded Plain Copper
INSULATION:
PVC Insulation According to UL 493 rated 600V
APPLICATION:
Specially designed for Direct Burial use in commercial
sprinkler and irrigation systems, golf courses, highways,
public parks, plantations and commercial farms.
PACKING:
Spools : 2500 feet
Shrink Wrap : 500 Feet
(no x
AWG mm) (mm) (mm) (Kg/Km)
info@wise-engg.com
3M™ Direct Bury Splice Kit DBR/Y-6
Applications The 3M™ Direct Bury Splice Kit DBR/Y-6 is used to electrically connect two or more pre–
stripped copper wires and moisture seal the connection for direct burial.
The kit includes a 3M™ Performance Plus Wire Connector R/Y+ and a high impact, UV-
resistant polypropylene tube prefilled with moisture-resistant grease.
RoHS 2002/95/EC
RoHS Compliant 2002/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the
maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance
is in an application that is exempt under RoHS. This information represents 3M’s knowledge and belief, which may be based in whole
or in part on information provided by third party suppliers to 3M.
Construction:
Tube : Impact and UV Resistant Light Blue Polypropylene
Dimensions: Length: 3.7in., Cover: 1.5in.x 1.1in., Diameter: 1in.
Grease: 711B
R/Y+ Connector: Steel Spring, Flame Retardant Insulator
Instructions
1) ¾ in. 2)
3) 4) 5)
Installation Tip:
If having difficulty getting the twist-on connector down into the tube when using small
gauge wires, use a thin non-conductive object to push the connector to the bottom of the
tube. Upon removal of the object, ensure that no voids or water paths remain in the
grease.
info@alrayyanksa.com
3M™ Direct Bury Splice Kit DBR/Y-6
Combination Chart
Example:
3 #14 SOL and
1 #12 STR
Shelf Life & This product has a 5-year shelf life from date of manufacture when stored in a
Storage humidity controlled storage (10°C/50°F to 27°C/80°F and <75% relative humidity).
Availability From your local distributor; or from 3M.com/electrical [Where to Buy] or call
1.800.245.3573.
Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information
believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must
evaluate it and determine if it is suitable for your intended application. You assume all risks and liability
associated with such use. Any statements related to the product, which are not contained in 3M’s current
publications, or any contrary statements contained on your purchase order, shall have no force or effect unless
expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited This product will be free from defects in material and manufacture at the time of purchase. 3M MAKES NO
Remedy; Limited OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
Liability MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product
or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any
indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal
theory asserted.
3M is a trademark of 3M Company.
info@alrayyanksa.com
info@wise-engg.com
BUBBLERS
FEATURES
• Pressure compensation ensures uniform output across various pressures
• ½" inlet
• Flow marked top for easy identification
0.9 Trickle
50 0.11 1.9 Trickle
Trickle
Trickle/
Umbrella
5-CST-B
1.0
150
1.4
2.1 210 1.5 1.5
2.5 0.10 1.6
76 Visit hunterindustries.com
Integral compact pressure-compensated
dripper, for permanent drip applications,
for growers who seek quick ROI. Ideal for
permanent crops in complex topography.
12009 - 12010 - 16009 - 16010 - 16011 - 16012
20010 - 20012
Drainage The dripper integrates a drainage mechanism that drains water from the pipe at the end of the
mechanism irrigation cycle, to allow easier recoiling of the dripline at the end of the crop cycle. Also helps in
countries where temperatures may drop below zero.
Continuously Flushes debris throughout operation, while ensuring constant dripper operation even in
self-flushing challenging water quality.
Wide filtration Ensures optimal performance even under harsh water conditions, preventing the entrance of
area sediment into the labyrinths.
TurboNet™ Labyrinth ensures wide water passages, to increase flushing efficiency. The water is drawn into
the dripper from the stream center, preventing the entrance of sediments into the drippers.
Specifications
Pressure-compensated range according to table below.
Recommended filtration: depending on dripper flow rate. Filtration method selected based on the kind and concentration
of dirt particles contained in the water. Wherever sand exceeding 2 ppm exists in the water, a Hydrocyclone shall be
installed before the main filter. Where sand/silt/clay solids exceed 100 ppm, pre treatment shall be applied following
Netafim expert instructions.
TurboNet™ labyrinth with large water passage.
Weldable into thick wall driplines (0.90, 1.00, 1.10, 1.20 mm).
Injected dripper, very low CV with injected silicon diaphragm.
High UV resistant. Resistant to standard nutrients used in agriculture.
Meets ISO 9261 Standards.
info@alrayyanksa.com
Drippers technical data
Model Inside diameter Wall thickness Outside diameter Max. working Max. flushing KD
(mm) (mm) (mm) pressure (bar) pressure (bar)
Model Wall thickness Distance between Coil length Average* coil Coils in a 40 feet Total in a 40 feet
(mm) drippers (m) (m) weight (kg) container (units) container (m)
* Calculated weight average. For further details see “Average Coil Weight Disclaimer”
info@alrayyanksa.com
2
DripNet PC™ 12009
Catalog number 17171 - (any of below 6 digits)
Flow Distance between drippers (m)
rate
(l/h) 0.15 0.20 0.25 0.30 0.33 0.40 0.50 0.60 0.65 0.70 0.75 0.80 0.90 1.00
0.4
0.6
1.0 000100
1.6 000200
2.0
2.3
3.0
3.5
3.8
Bundled
coil length 500 500 500 500 500 500 500 500 500 500 500 500 500 500
(m)
Bundled
coil length 500 500 500 500 500 500 500 500 500 500 500 500 500 500
(m)
info@alrayyanksa.com
DripNet PC™ 16010
Catalog number 17665 - (any of below 6 digits)
Flow Distance between drippers (m)
rate
(l/h) 0.15 0.20 0.25 0.30 0.33 0.40 0.50 0.60 0.65 0.70 0.75 0.80 0.90 1.00
0.4
000014 000020 000019
0.6
000250 000370 000390 000547 000600 000620 000700 000750 000790 000800 000900 000950
1.0
001060 001160 001450 001625 000005 001820 001875 002060 002125 002160 002200 002600 002800 003050
1.6
005820 006025 006075 006270 006280 006470 006620 006860 006890 007000 007210 007460 007550 007830
2.0
008430 008460 008530 005833 008550 008600 009592 009587 008570 009594 009595 009596 009597
2.3
3.0
009620 009635 009685 009690 009790 009940 010120 010160 010250 010530 010720 010800 011120
3.5
3.8
012300 012350 012400 000016 012560 012600 012700 012735 012750 012800 012830 012860 013000
Bundled
coil length
(m) 500 500 500 500 500 500 500 500 500 500 500 500 500 500
Bundled
coil length 500 500 500 500 500 500 500 500 500 500 500 500 500 500
(m)
Bundled
coil length 400 400 400 400 400 400 400 400 400 400 400 400 400 400
(m)
info@alrayyanksa.com
@netafim.com
W
a
n
t
t
o
k
n
o
w
m
o
r
e
?
p
r
o
d
u
c
t
s
_
s
o
l
u
t
i
o
n
s
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
1- Irrigation material Specification
Subject: irrigation material submittal
Specification
IRRIGATION PART
GENERAL
1.1. Description
The scope of work shall be read in conjunction with the contract material
specifications, contract drawings and installation details and it includes but
not limited to the following:
A. The contractor shall prepare the shop drawings showing but not limited to The
Main line route and sizes, Laterals route and sizes, solenoid valves, control
wires route and numbers, Irrigation Controllers, sprinklers, integrated dripper
lines, on line drippers, Bubblers and flush valves.
B. The contractor shall submit for client approval all technical information and
samples of the materials he intends to use. These materials should be in
accordance with the material specifications of this project.
C. The contractor shall commission the irrigation system upon completing the
work and then shall be handed over.
D. The contractor and upon completing the work shall provide the client with
three original sets of As-Built drawings accurately reflecting the executed
works and installation details.
E. The contractor shall upon completing the works provide the client with
detailed Operation and Maintenance Manuals (With applicable Arabic
translations) in three originals. The manuals shall include but not limited to:
i. Complete and marked literature of all products used on the
projectand its reordering part numbers.
F. The client prior to issuing the project handing over certificate shall approve
the As-Built drawings and the operation & maintenance manual.
1.3. Quality assurance
C. DIN 8074: This standard specifies dimensions for pipes made of high-density
polyethylene (HDPE).
D.DIN 8072: This standard specifies dimensions for pipes made of linear low-
density polyethylene (LLDPE).
F. BS: 1780: Specification for bourdon tube pressure and vacuum gauges.
G.BS: 3505: Specification for uPVC pressure pipes for cold potable water.
H.BS: 4346: Joints and fittings for use with uPVC pressure pipes
I. BS: 5150: Specification for cast iron wedge and double disk gate valves for
general purposes.
J. BS: 5154: Specification for copper alloy globe, globe stop and check, check
and gate valves for general purposes
1.5 SUBMITTALS
A. Shop Drawings: The contractor to prepare the project shop drawings in
three sets which to be approved by the client representative prior to
commencing installation work. The contractor shall prepare the shop
drawings showing but not limited to The Main line route and sizes, Laterals
route and sizes, solenoid valves, control wires route and numbers, Irrigation
Controllers, sprinklers, integrated dripper lines, on line drippers, Bubblers and
flush valves.
B. Products: The contractor shall submit for client approval prior to commencing
installation works; the products he intends to use with all technical details and
literature in accordance with the specifications below.
C. Operation and Maintenance Manuals: The contractor shall submit three sets
of the detailed Operation & Maintenance Manual with equipment reordering
codes and literature.
D. As-Built Drawings: The contractor shall submit three sets of the complete
project as-built drawings reflecting the actual site installation.
PART 2 - PRODUCTS
2.1. GENERAL
E. Flexible Pipes for irrigation on line drippers shall be in the required sizes as
shown on the drawings and B.O.Q extruded from linear low density
polyethylene version raw material. Pipes shall be resistant to algae and
ultraviolet deterioration with Carbon Black content not less than 2.25 %.
A. SPRINKLERS:
The sprinkler shall be available with a 4", 6", or 12" (10 cm, 15 cm, or 30
cm) pop-up stroke, depending on the body specified, to bring the nozzle
into a clean environment. The sprinkler shall be available as an
aboveground shrub head. The sprinkler shall have the option of either a
factory-installed or field-installed drain check valve capable of checking
up to 10' (3.0 m) in elevation change. When specified as factory-installed,
the sprinkler shall have the words “CHECK VALVE” stamped in white
lettering on the body cap. The sprinkler shall have available an optional,
Snap-On cap, molded in purple alcryn rubber, or a replacement body
cap, molded in purple to indicate the use of reclaimed water. A vandal–
resistant locking cap shall be available as a field-installed option.
The strip pattern nozzle shall be available with models to cover the
following strip pattern:
The sprinkler shall be available with a 4", 6", or 12" (10 cm, 15 cm, or
30 cm) pop-up stroke, depending on the body specified, to bring the
nozzle into a clean environment. The sprinkler shall have the
option of either a factory-installed or field-installed drain check valve
capable of checking up to 14' (4.3 m) in elevation change. The
sprinkler shall come with a gray body cap to indicate the MPR40
product line for easy identification in the field except for conditions as
when reclaimed water units are ordered. The sprinkler shall have
available an optional, Snap-On cap, molded in purple, a replacement
body cap, molded in purple to indicate the use of reclaimed water, or a
pre-installed molded purple body cap to indicate the use of reclaimed
water.
The part-circle sprinkler shall have an infinitely adjustable arc from 45°
to 105°, 90° to 210° or between 210° to 270° depending on the model
selected. The full circle sprinkler shall irrigate a full 360°. The 45° to
105° model shall not require coverage from adjacent sprinklers closer
than 1 m from the head.
This same ratcheting action shall allow the orientation of the left edge
of the variable arc when installed on a fixed riser or in a pop-up body.
This is independent of and in addition to any ratchet that may exist in a
pop-up body.
The sprinkler shall have a Pressure Port™ feature that will ensure
better dispersal and close-in watering.
The sprinkler shall be equipped with a drain check valve to prevent low
head drainage, and be capable of checking up to 15 feet (4.5 m) in
elevation change.
When specified, the sprinkler shall have high speed feature that cuts
full circle rotation time from three minutes to one, for quick and light
wet downs of sports fields or any areas that require dust control.
When specified, the sprinkler (full circle version) shall have Dual
Opposing Nozzle for superior coverage with maximum efficiency. The
primary and secondary nozzles on opposing sides of the turret,
causing streams arc in opposite direction as the sprinkler rotates to get
outstanding midrange and close in watering.
The sprinkler shall have a rubber cover firmly attached to the top of the
riser. When specified, the sprinkler shall have a cover molded of
purple Alcryn rubber to indicate the use of reclaimed water. A
protective rubber boot shall surround the rubber cover when sprinkler
is in the retracted position.
Model:
Features:
For use with Funny Pipe and other thick walled 1/2” ID tubing.
Use in drip irrigation, home sprinkler systems & other residential irrigation
applications.
Spiral barb design allows quicker twist-on installation.
Made of Celcon® plastic resin providing long term durability.
Model:
0.49” ID
Features:
The dripper shall have a single outlet, flow rate base color coded and it shall
be available in 2, 4, 8.5 and 25 Liters per Hour (LPH).
The drippers shall be of the pressure compensating type (the flow shall be
unaffected by varying inlet pressure and field slope) and continuously
selfcleaning type (high resistance to clogging).
The dripper shall have large, wide and deep flow path cross section to
minimize clogging and ensuring exact flow rate in all conditions
The dripper shall have a uniform flow rate at a pressure range of 0.5 - 4.0
bars.
The 2.0, 4.0 and 8.5 drippers shall be of the barb type with flat or nipple
outlet.
The 25.0 (LPH) dripper shall be of the barb type with nipple outlet with a
special dust cap.
The dripper shall have a single outlet, flow rate base color coded and it shall
be available in 1.2, 2, 3, 4, 8 and 12 Liters per Hour (LPH) flow rates.
The dripper shall be of the compact pressure compensating type (the flow
shall be unaffected by varying inlet pressure and field slope) and continuously
self-cleaning type (high resistance to clogging).
The dripper shall have large, wide and deep flow path cross section to
minimize clogging and ensuring exact flow rate in all conditions.
The 1.2 (LPH) dripper shall have a flow path with width 0.67 mm, depth 0.77
mm and length 35 mm.
The 2.0 (LPH) dripper shall have a flow path with width 1.03 mm, depth 0.75
mm and length 35 mm.
The 3.0 (LPH) dripper shall have a flow path with width 1.03 mm, depth 1.08
mm and length 35 mm.
The 4.0 (LPH) dripper shall have a flow path with width 1.32 mm, depth 0.95
mm and length 35 mm.
The 8.0 (LPH) dripper shall have a flow path with width 1.60 mm, depth 1.05
mm and length 35 mm.
The 12.0 (LPH) dripper shall have a flow path with width 1.60 mm, depth 1.05
mm and length 17.5 mm.
The dripper shall have a uniform flow rate at a pressure range of 0.5 - 4.0
bars.
The dripper shall be of the barb type with 3 mm barb outlet, 4 mm barb outlet
or nipple outlet.
The dripper line shall consist of a ultra violet resistant low density linear
polyethylene tube with pressure compensating continuously self-cleaning
integral flat drippers welded to the inside of the wall of the tube at the
specified spacing as an integral part of the tubing assembly.
The tube shall have a 16.2 mm outside diameter and it shall have 1.0 mm
wall thickness (3.5 bars maximum working pressure)
The dripper shall be available in 1.0, 1.6, 2.3 and 3.5 liters per hour (LPH)
flow rates utilizing a combination turbonet flow/reduced pressure
compensation cell mechanism with a double labyrinth path and a silicon
diaphragm to maintain uniform discharge rates.
The dripper shall have a double labyrinth path above and below the
diaphragm, providing a wide cross section passage.
The 1.0 (LPH) dripper shall have a constant K=1.0 & flow exponent X=0
and a flow path with width 0.83 mm, depth 0.74 mm and length 40 mm.
The 1.6 (LPH) dripper shall have a constant K=1.6 & flow exponent X=0 and
a flow path with width 1.26 mm, depth 0.70 mm and length 40 mm.
The 2.3 (LPH) dripper shall have a constant K=2.3 & flow exponent X=0 and
a flow path with width 1.26 mm, depth 1.00 mm and length 40 mm.
The 3.5 (LPH) dripper shall have a constant K=3.5 & flow exponent X=0 and
a flow path with width 1.59 mm, depth 1.15 mm and length 40 mm.
The dripper shall have a root physical barrier improves resistance to clogging
caused by root penetration.
The dripper line shall be suitable for surface and subsurface irrigation.
The dripper shall have a uniform flow rate at a pressure range of 0.5 - 4.0
bars.
The electrical solenoid valves shall be of the globe type normally closed,
electronically actuated, diaphragm operated.
The valve shall be available in a globe body style with 1", 1 ½", or 2" Female
National Pipe Thread (FNPT) inlet and outlet. The 3" model shall be available
in a combination globe/angle configuration. When specified, the valve shall be
configured with British Standard Pipe threads. The valve shall be equipped
with a flow control mechanism with removable handle that will regulate flow
from full on to completely off. When specified for use with reclaimed water, a
reclaimed water identifier handle shall be available.
The standard solenoid shall be a 24 VAC unit with a 350mA inrush current
and 190mA holding current at 60 cycles and a 370 mA inrush current and 210
mA holding current at 50 cycles. When specified, the unit shall be equipped
with a DC latching solenoid for use with battery-operated controllers. The
solenoid shall be an encapsulated, one-piece unit with captive plunger. It shall
be equipped with manual internal and external bleed capability to release the
upper chamber water to the downstream piping, or to atmosphere, allowing
the valve to open.
Air relief valves shall be of the sizes shown on the Drawings and shall be of
the kinetic/automatic type that will automatically release air when the lines are
being filled with water and when air entrapment occurs while the system is
working.
The Valves shall be of the 2”size with plastic or brass male base. The body of
the valve shall be constructed heavy duty plastic.
The working components of the valve shall be constructed of 100% corrosion
resistant materials to ensure maximum life and minimum water loss due to
leaks.
The Air Release valve shall employ roll seal mechanism made of EPDM and
shall remain open even when pipeline air pressure reaches 10 psi.
Gate valves shall be designed for a working pressure of not less than 10 bars
and water operating temperature of 45° C.
Valves shall be the same size as the incoming line size with a clear waterway
equal to the full nominal diameter of the valves and shall be opened by
turning counter clockwise.
The operating nut or wheel shall have an arrow cast in valve indicating the
direction of opening.
Valves smaller than 75 mm shall be all bronze or brass conforming to BS
5154 with threaded inlet and outlet.
Valves 75 mm and larger shall be cast iron body, and shall conform to BS
5150 with flanged inlet and outlet.
The valve boxes shall have enclosures, which are made of M 80064F series
injected molded grade High Density Polyethylene (HDPE) with ultra violet
additives, according to ASTM-D-1238.
It shall be light in weight with reduced side angles and increased break
resistance.
The valve box shall be non-conductive or sparking.
The valve boxes shall be available in sizes 610, 910, 1419, 1320 and 1324
depending on installation requirements as per scope of work, specifications
and drawings.
The filtration system shall consist of a twin disc filter Battery having two or
more 4” units depending on the flow and the water quality as specified on the
drawings. Each unit shall be capable to filter between 160 and 450 GPM
depending upon the quality of water.
The filters shall be of the ‘grooved disc’ design providing both surface and
depth filtration in a compact design, thus leading to bigger filtration area and
giving extra protection to the system.
The filtration rate of the filter shall be compatible with the irrigation system
flow and pressure and the filter shall be rated for pressure not less than 10
Bars.
The filters could have the capability to be assembled on a filter battery with
automatic ‘backwash’ system controlled by a pressure differential switch. The
manifold of the battery shall be black steel epoxy coated, pipes.
Filtration shall not be less than 120 meshes, unless otherwise indicated on
the contract drawings.
2.5. Irrigation controllers and irrigation cables and central control system
3Part 1 – General
1.1 The Central Control System shall consist of internet hosted control software capable
of monitoring and managing an unlimited number of dial-based commercial irrigation
controllers via Wi-Fi or Local Area Network (LAN) connections.
A. The Central Control System shall display in an internet browser the status of
all controllers in list and/or map overviews, including controller dial position,
adjustment status, and any timed weather shutdowns.
All controllers shall be visible in a live, online map and located automatically
based on the user-supplied controller address.
I. The map shall be selectable between “street” and “satellite” or terrain views.
II. The map shall automatically size to the extents of the controller locations to
show all controllers, and users may then zoom, pan, and navigate freely
throughout the map for controller selection purposes.
B. The Central Control System shall permit selection of any controller, and then
offer full remote programming of all controller features in the browser,
including irrigation scheduling, controller settings, and weather-based
watering adjustments.
C. The Central Control System shall allow the user full remote control
capabilities, including starting and stopping individual stations and programs,
or setting the controller to Off for a user-defined number of days. The System
shall also allow quick adjustment of irrigation amounts by a percentage value.
D. The Central Control System shall be compatible with locally-installed smart
weather adjustment sensors, which may adjust each controller’s irrigation
amounts automatically based on local climate conditions, and shall report
such adjustments in the browser to the user. The software shall also report
controller shutdowns due to active rain, freeze, or other sensors.
E. The Central Control System shall display the forecast weather for each
controller several days in advance, and shall enable automatic shutdowns of
irrigation when forecasted temperature or chance of rainfall exceeds a
userspecified amount.
F. The Central Control System shall have multi-user permissions for
maintenance organizations, where each controller shall have a designated
owner, who may then grant control access for specified controllers to other
authorized personnel by email address.
I. Both crewmembers and controllers may be organized into named
groups.
II. Access may be granted or cancelled at any time (by individual or
group) by the designated owner.
G. The Central Control Software shall automatically alert owners and/or
designated crewmembers via SMS text messages when selected alarms
occur at a controller location, indicating the controller and the type of alarm for
rapid response or repair.
4Part 2- Security
2.1 The Central Control Software shall use transport layer security to ensure
secure IoT (Internet of Things) communication.
A. The Central Control Software users shall also be protected by a well
designed application layer security model that protects the settings and
communication of each of user.
B. The Central Control Software shall be protected by Network Layer Security
designed to minimize potential attack surface.
5Part 3 - Communications
3.1 Controllers in the System shall be connected to the internet via either Wi-Fi, or
Ethernet/LAN, through local routers.
A. Wi-Fi connections shall conform to 802.11 b/g/n standards, with all necessary
approvals and compliance for 2.4 GHz wireless devices.
B. Ethernet connections shall be by standard RJ-45 hardwired jack to the
network via approved cable (CAT5, CAT5e, CAT6, or equal).
C. Communications modules shall be affixed to the host controllers via a
dedicated, manufacturer-supplied opening or knockout in the controller
enclosure.
I. Communication modules shall be of robust construction designed for
outdoor use.
II. All communication modules shall feature readily visible status lights
(LEDs) to show status of communications with the local router,
network, and central control software.
6Part 4 - Compatible Controllers
4.1 The irrigation controllers shall be supplied by the same manufacturer of the Central
Control System, and warrantied for use together as a complete system.
A. The controllers shall be commercial grade irrigation products with the ability to
run at least two irrigation stations, plus a Pump/Master Valve output,
simultaneously.
B. The controllers shall have at least 4 automatic irrigation programs with the
ability to overlap programs to complete watering in larger systems.
C. The controllers shall have familiar dial and pushbutton control panels to
enhance user ease of programming in the field. The controller features shall
be operable either in the field, or via the Central Control Software.
D. The controllers shall include water-saving features such as cycle and soak,
delay between stations, rain sensor inputs with automatic shutdown, and
manual or automated Seasonal Adjustment.
E. The controllers must be compatible with a local, license-free remote control
that is independent of internet connectivity.
F. The Central Control Software shall detect any settings or scheduling conflict
between the software and the hardware, and shall alert the user if a conflict is
detected. The software shall have the ability to identify and display any
conflicts, and allow the user to decide which settings shall be used.
Part 1 – General
1.1 The controller shall be a full-featured commercial-industrial product for the purpose
of irrigation management and monitoring of control valves, flow, and sensors, via
tow-wire decoder connections
B. Plastic Pedestal
1. Pre-assembled controller dimensions shall be: Height 39”/90 cm, Width
24”/61cm, Depth 17”/43 cm.
2. The enclosure shall be of double-walled roto-molded construction for
durability and insulation.
3. Plastic pedestal shall be mounted on concrete slab with pre-installed PVC
conduit sweeps for underground wire runs, including separate sweeps for AC
power wiring, earth ground, and field wiring.
4. Surge protection shall include a self-resetting thermal circuit breaker in the
transformer, glass 250V fast blow fuse, positive temperature coefficient (PTC)
breakers at key points, and gas-filled spark gap arresters where necessary.
5. Controller shall include copper-clad steel ground lug for connection to earth
ground hardware.
6. A 751CH key shall be mounted in the enclosure door for security
a. Two (2) keys shall be provided per each controller
2.3 Warranty
A. Wall mount and pedestal enclosure and installed equipment shall carry a conditional
5 year warranty
B. Panel shall include ‘soft keys’ labeled for different functions in different screens to
facilitate programming and navigation
C. Panel shall include an SD card reader for storage of backups and logs, as well as
field updates of software
4. The field decoders shall be directly programmable with station numbers, and
shall not require serial number assignments at the controller panel. The
controllers shall also be addressable in the field with a wireless handheld
programmer connection.
5. The decoder output module(s) shall be equipped with status LEDs, and shall
be locked into place with a sliding lock. A warning LED shall flash when the
slide is in the unlocked position. Operation of the slide lock shall also reboot
the controller operating system. The control panel shall not require a
dedicated “reset” button.
B. A programmable rain delay shall allow the user to specify a number of days for the
controller to remain shut down after restoration of a sensor alarm, such as a rain
event.
3.7 Pump / Master Valve Outputs
A. The controller shall have 3 built-in P/MV outputs with a capacity of up to .800
mA each
a. Each P/MV output shall have at least 12.5kV surge protection, supplemented
by copper induction coils
4.1 General
A. Display shall be selectable in 12 languages
B. The display shall include selectable settings for date, time, units of
measurement, and regional preferences.
4.2 Programming
A. The controller shall have 32 independent programs with unique day
schedules, start times, and station run times
B.Each program shall allow Day of Week, Interval, or Odd/Even schedule
types
C.Each program shall offer up to 10 start times
D. Each program may be allowed to overlap, stack, or SmartStackTM to a
user specified maximum number of simultaneous programs
E. Each program may have programmable Non-Water Windows, during which
automatic irrigation will not be allowed
1. Missed irrigation as a result of water window violations is logged and
announced as an alarm
2. Manual irrigation for maintenance purposes shall not be inhibited by Non
Water Windows
D.The controller shall have true Calendar Date Off programming, allowing
specific dates to be skipped at any time of year, by program. Off dates may
be recurring, or one-time occurrences
E. The controller shall provide a User Management function to limit access
to programming and other operations, with unique passwords for multiple
users, permitting either full or partial access to controller functions
1. User logins and activities shall be tracked by user ID, if password security is
enabled
2. The controller shall automatically log users out after a period of inactivity
F. The controller shall allow Easy RetrieveTM backup of all programming and
configuration to preserve the original configuration, which may be restored at
any time
1. The backup file shall also be stored to an SD card if desired
2. Multiple backups may be stored with unique file names on the SD card for
different scenarios
G.The controller shall log all incidents and activity, organized into the following:
1. Alarm Logs shall include the last 250 alarm events with date/time stamp to
the second
2. Controller Logs shall include the last 250 controller events
3. Station Logs shall include the last 1500 recorded irrigation events of all types
4. All logs shall appear in the selected language of the controller
H.Flow Operations
1. Controller shall feature independent flow management and flow monitoring in
each of up to 6 flow zones.
2. Controller shall allow flow budgeting at flow zone and mainline levels to
monitor total monthly water usage, and provide an alarm when the
budgeted amount is exceeded
J. Flow monitoring uses a flow sensor to monitor actual flow, and intervene
when high or low flow conditions are detected
1. Controller shall allow the station flows to be learned and entered
automatically.
2. The station flow values shall be adjustable for high and low flow alarm limits
3. The station flow alarm settings shall have an adjustable delay factor to allow
flow to stabilize
4. Each flow zone shall have an absolute high flow limit, independent of the
station level flow monitoring
5. Each flow zone shall allow Unscheduled Flow allowances to permit manual
watering within user programmable limits
6. Each flow zone shall include adjustable recovery settings for high level flow
alarms, allowing irrigation to be automatically allowed after an elapsed
period of time, or manually only, requiring a user to visit and clear the alarm
K.Flow operations shall also include the ability to assign a separate flow sensor
and master valve to the mainline level, above the independent flow zones, to
monitor and protect long runs of mainline pipe
1. Flow monitoring at the mainline level shall allow faster reaction to high or
unexpected flow conditions, without the delay of station level diagnostics
2. Mainline protection may have its own monthly water budget, high flow and
unscheduled flow limits, separately from lower level flow zone assignments
The Solar Sync shall automatically adjust run times for controller stations based on a local
evapo-transpiration sensor, connected to a compatible automatic irrigation controller via
SmartPort interface.
The Solar Sync shall include only local evapo-transpiration data, “local data” being defined
as sensed climatological conditions within the immediate coverage area of the irrigation
system, from a sensor dedicated to that purpose. The Solar Sync shall not require
broadcast, subscription, or other generalized weather data, and shall function as a
standalone ET-based irrigation system when directly connected to a compatible automatic
irrigation controller of up to 48 stations.
The Solar Sync shall consist of two physical components, including a Solar Sync
Sensor mounted in an optimum location for measurement of climatological data, and a
module, containing database information which shall be connected to the irrigation
controller’s SmartPort.
The Solar Sync Sensor shall be mounted within 200 ft./60m of the irrigation controller. The
Solar Sync Sensor shall include individual sensors for solar radiation, and air temperature,
and shall also include a rain sensor. The rain sensor shall be capable of interrupting the
power from the irrigation controller to the valves when rainfall exceeds a pre-selected
amount.
The rain sensor circuitry shall utilize 2 sets of hygroscopic disks to activate switches in the
unit. One switch will be for the total rainfall compensation unit and the other for the Quick
Response unit. The Quick Response unit will turn off the irrigation system within 5
minutes of the onset of precipitation, depending on the intensity.
The sensor shall be adjustable by turning a plastic collar on the device that regulates an
opening, thus varying the rate of evaporation from the disks.
In addition, the built-in temperature sensor shall be capable of interrupting the power from
the irrigation controller to the valves when ambient air temperature falls below 37 degrees
Fahrenheit (3 degrees Centigrade).
All sensors shall be integrated into a single array, and shall be housed in an UV and
corrosion resistant plastic casing.
The sensor shall have an integral, adjustable, aluminum, mounting bracket that allows
installation on angled, as well as perpendicular surfaces. The sensor shall have a mounting
option that allows for installation on a rain gutter.
The Solar Sync shall permit the user to designate a no water window that prevents any
irrigation from occurring during a specific period of the day.
The Solar Sync shall be fully functional with 24VAC input or less, with a max current draw of
25ma, and shall not require a dedicated high-voltage transformer or connection. The Solar
Sync system shall be CE [C-tick] approved.
The Solar Sync shall be installed in accordance with the manufacturer’s published
instructions, and shall carry a conditional five-year exchange warranty for wired sensor and
receiver and ten-years for wireless sensor only.
The soil moisture monitoring system shall consist of a solid-state, low-voltage, outdoor
control module mounted within 6 ft/2 m of the host irrigation controller, wired to a soil
moisture probe consisting of ABS plastic caps with stainless steel body over a hydrophilic
fabric covered granular matrix with embedded stainless steel electrodes.
The soil moisture control module shall operate on 24 VAC power from the host controller.
The control module shall have color-coded wiring for all connections including 24V power,
the soil probe, and the module output. The output shall consist of a relay-actuated,
normallyclosed contact closure suitable for compatible controller sensor input, or for
common wire interrupt in a 24 VAC irrigation valve wiring system.
The soil moisture control module shall be designed for outdoor mounting, although
protection from direct sunlight and direct sprinkler spray is recommended. The control
module itself shall be NEMA 3R rated and shall be operable from 0° F/-17° C to 140° F/60°
C. The control module shall be provided with suitable mounting hardware for common
exterior applications, including screws and anchors. The control module shall display FCC,
CE, and C-tick approvals.
The soil moisture control module shall have an LCD display and sealed pushbuttons for
programming.
The module shall display current soil moisture level, and shall permit the operator to update
the reading at any time.
The module shall allow the user to visually set the desired moisture level, and shall provide
sensor output to the controller, or common wire interrupt, when the level is reached.
The module display shall indicate whenever the module has interrupted irrigation. The
soil moisture control module shall also permit an override or “pause” by the user, to
permit irrigation regardless of moisture level under special circumstances. The control
module shall provide a clear visual indication when it is overridden, until the operator
restores it to normal control.
The soil moisture probe may be installed up to 1000 ft/300 m from the control module, using
18 AWG/1 mm2 direct burial rated wire. No more than one soil moisture probe shall be
connected to a single soil moisture control module. [Multiple control modules may be
connected to controllers having more than one available sensor input.]
The soil moisture probe shall be located within the last zone of irrigation scheduled to run in
the controller, to prevent premature interruption of normal watering. The soil moisture probe
shall be placed in the sunniest, driest spot of the irrigated area.
The soil moisture probe shall be installed so that it is in full contact with the native soil. The
soil moisture probe shall be placed in a vertical position (within 45°) within the root zone of
irrigated plants that are typical of the landscape. The probe may not be installed
horizontally, under any circumstances.
The probe may be installed in a bored hole of 7/8”/22 mm diameter, followed by a slurry
mixed of water and native soil, to enhance contact with the soil.
The soil moisture monitoring system shall have a minimum 5 year manufacturer’s warranty.
The control module and the probe must be separately available as replacement parts, if
needed.
2.5.5 - Cables:
a. Power Supply Cables: All 230/240 volt cables shall be as per SASO
and IEC standards.
iii. The cables conductor shall be solid copper, U.F. type. Each
conductor shall have PVC insulation.
7. IRRIGATION MISCELLANEOUS
Irrigation Drip Line Stakes: Stakes for securing flexible pipes shall be galvanized steel wire,
Gauge 8. Minimum overall length of hoop-shaped stake is 20cm.
Non-metallic Nipple: Nipples where used shall conform to SAS 14/15, Class 5
uPVC or BS 4346: Part I, uniformly grey in color.
Keys: the Contractor shall provide Keys for all valves, controller cabinets, boxes, quick
couplers, etc. The number of keys to be provided to the Engineer for each type of fitting
shall be six (6).
Hoses: Hoses, quick couplers and appropriate connectors shall be provided
by the Contractor for quick coupling valves, drain down points, 'Y' strainer
blow down points, etc.
Quick couplers and hoses - One (1) quick coupler with swivel end unit and twenty five (25)
meters of industrial weight double nylon cord reinforcement hose for each installed eight (8)
quick coupling valves.
PART3. EXECUTION
3.1. Protection
3.2.1. The Contractor shall stake-out the locations of all pipe and valves and the
layout of work as accurately as possible.
3.2.2. The Contractor shall verify all horizontal and vertical site dimensions prior to
staking.
3.2.3. The Contractor will be responsible for relocating any existing services after
first obtaining the Engineer's approval. The Contractor shall remove and relocate
such services, at his own expense, if so directed by the Engineer.
3.2.4. Before starting work on irrigation systems, the Contractor shall carefully
check all grades to determine that work may safely proceed, keeping within the
specified material depths.
3.2.5. Fittings installed on pipes beneath pavements or walls shall be shown on
drawings.
3.2.6. All changes shall be recorded on daily basis on the “As-Built" worksheets.
3.3. Inspection: The Contractor shall inspect all products for damage immediately
before installation. Any products that are found to be damaged or not in
accordance with the specifications shall immediately be repaired or removed from
the site and replaced. Repairs shall not be undertaken without the Engineer's
approval of Contractor's proposed action.
3.4. Installation
1. Jointing:
3.4.8. Tagging and Identification: All remote control valves, motor-operated valves,
pressure reducing valves, manually-operated gate valves and controllers shall be
tagged and identified. All identifying numbers shall be consistent with like
designations indicated on the irrigation controller schedule.
3.4.9. Site Equipment Installation:
a.Isolation Valve/Gate Valve: Shall be installed as detailed and where
indicated on Drawings.
b. Remote Control Valve Assembly: Shall be installed in the positions as
indicated in the details, remote control valve assembly comprising gate
valve, remote control valve with pressure regulator, and all
appurtenances. Valve boxes containing the assembly shall not be
placed closer than 300mm to paved areas. When the pressure gauge
has been properly attached, the outlet pressure shall be set as
required during coverage tests.
c.Valve Boxes: Shall be installed as detailed and where indicated on
Drawings. All valves and valve assemblies shall be mounted in boxes
as detailed.
- The top of all boxes shall be set parallel with the grade and as detailed in
a neat and orderly fashion.
- Shall be placed parallel to paving, curbs, walls or similar structures and
where more than one box, parallel to each other.
- All box locations shall be reviewed with the Engineer prior to installation
of valves.
- Valve boxes shall not rest on or come in contact with the valve, piping,
hose or conduit.
- Valve circuit number of the remote control valve shall be painted on rim
of box, such that:
iv. A soak away 500 mm deep shall be provided under all valve boxes
using clean crushed aggregate 20 - 30 mm nominal size.
d. Control System:
- Irrigation Controller:
- Irrigation/Electrical:
e. Sprinkler heads:
- Lawn rotary sprinkler heads with 1/2" (12.7 mm) inlet
shall be connected to the lateral line by installing a 12.7 mm (1/2”) PE
flexible swing joint assembly and as shown on the detail drawings.
- Lawn rotary sprinkler heads with 3/4" (19 mm) inlet shall be
connected to the lateral line by installing a 3/4" (19 mm) PE flexible swing
joint assembly and as shown on the detail drawings.
- Lawn rotary sprinkler heads with 1" (25.4 mm) inlet or greater shall
be connected to the lateral line by installing an equivalent size PVC arm
swing joint assembly and as shown on the detail drawings.
g. Concrete Pads:
3.5.1. Purging:
b. Test shall be made only after completion of the above operations and
not until at least seven days after the last concrete thrust anchor block
has been cast.
c. Contractor shall supply all testing material and equipment, including
all caps, valves, pumps, tanks and gauges as required.
d. Pressure gauges shall be dual reading in bar and PSI units.
Calibration shall be such that accurate determination of potential
pressure loss can be ascertained.
e. The section of the main pipeline to be tested shall be filled with
potable water and all air expelled. After the main pipeline has been
completely filled, the pressure shall be steadily and gradually
increased until the specified test pressure has been reached.
Simultaneous pressure and leakage tests and separate pressure test
shall be made at 150 % of working pressure at the point of test, but not
less than 125% of normal working pressure at highest elevation.
Separate elevation test shall be made at 150 % of normal working
pressure of the segment tested. Duration of simultaneous pressure
and leakage tests shall be 2 hours and duration of separate pressure
tests shall be 1 hour. All testing shall comply with AWWA M23-80,
Polyvinyl Chloride Pipe Design and Installation. A graph shall be
produced showing water input against time and the test shall run until
the graph curve flattens out. Testing shall comply with AWWA
specifications and requirements.
f. Separate tests shall be applied to the lateral distribution pipe work
and the irrigation pipe work from the remote control valves outwards.
Test pressures for these shall be as described above.
g. When testing the irrigation lines from the valves, discharge devices
shall be replaced with temporary plugs or caps.
h. All trenches with pipe installed shall be immediately backfilled with
preliminary sand backfill sufficient to prevent arching or slipping under
pressure. All joints, fittings and connections are to remain exposed
until successful completion of hydrostatic testing.
i. Other than for preliminary sand backfill over pipes, no work shall be
covered before it has been inspected, tested and approved by the
Engineer
j. During the tests, all exposed couplings, fittings and valves shall be
carefully examined for defects and leakage. Leaking pipes, couplings,
joints, fittings and equipment shall be repaired or replaced and the
section retested as previously specified.
k. Upon receipt of approval of the Engineer to proceed, the remaining
backfill shall be placed and compacted to ninety percent (90%) of
maximum dry density.
3.5.3. Final System Test:
The tests as specified above shall be repeated for the entire network after pipelines
have been backfilled, cleaned and inspected. Each test shall be restricted to pipes of
one class and particular care shall be taken to isolate air valves, etc. and not to apply
higher pressures than specified at any point on the pipeline and to ensure that the
pipelines are adequately anchored before any test is carried out.
1. Test Results:
Written records of every test clearly identifying the tested section of the pipe together
with time of test and name of testing engineer in tabulated format shall be submitted
for review and approval by the Engineer upon completion of the tests.
3.6 Flushing:
3.6.3. The lines shall be operated for a period of 24 hours, not necessarily in one
continuous period, and all sprinklers, emitters and dripper lines checked for
satisfactory operation. Any faulty/blocked emitters shall be replaced.
END OF SECTION
4-Irrigation pipe and fittings
MAIS company
info@alrayyanksa.com
info@wise-engg.com
Al Rayyan Nursery Company CLA-CIJjJI cil!JJI cJJLu.a..o �J...W
C.r 2053029968 2053029968 ...::, .._,..
A�AYYAN
3. WELDING FITTINGS
These fittings are used to connect large diameter pipes, in such
applications as Central pivot.
6. ACCESSORIES
In addition to producing Bubbters and Drippers, Mais also produces
accessories such as Tubing distribution small stake, Bubbler stake,
Puncher, Tree Clip, Valves and others.
7. DISC FILTERS
8. MAIS PC TONE
9. MAIS TONE
--
Al Rayyan Nursery Company CJ.!...CIJj.JI 6'-!J J I c.Ul..w...o a.S J.ill
C.r 2053029968 2053029968 -::, .._,.,
A�AYYAN
I
� . -
W.P. = 4 BAR
-
II 1.0. Unit Weight
Nominal 0.0. I 0.0. W.T.
Size (mm) ! (mm) (mm) (mm) (grim}
--
-- 16 16 1.2 13.6 59
-- 20 20 1 .5 17.0 90 -
-- 25
32
25
32
2.0
2.0
21.0
28.0
145
188
- 4 BAR
PIPES DIMENSIONS BASED ON AUSTRALIAN STANDARD AS 2698.1 -1984
I . .
WP.
I
-� ---- - -- -· - --
Nominal 0.0.
Size (mm)
0.0.
(mm)
W.T
(mm) II 1.0.
(mm)
I
Unit Weight
(grim)
--
+
4.5 4.50 0.75 3.00 8
5.8 5.80 0.90 I
I
4.00
I 12
- 16.0 16.00 1.50 13.00 68
25.0 25.00 1.50 I 22.00 111
0.0. Outs,de Diameter
W.P. = Work,ng Pressure AT 20°C
W.T. Wall Thickness
I.D. Inside Diameter
Al Rayyan Nursery Company CL!-CIJj.JI C:.,�JJI cilWLO cr..=:,µi,
C.r 2053029968 2053029968 ..::,.__,..
A�AYYAN
305
�-----�
Clamp Saddle with Two Bolts
mm X inch
75 X 1 l /2"
90 X l /2"
90 X 3/4"
25 X 1/2"
90 X 1"
25 X 3/4"
90 X 1 l /4"
32 X 1 /2"
90 X 1 1/2"
32 X 3/4"
90 X 2"
32 X 1"
90 X 2 l /2"
40 X 1/2"
110 X l /2"
40 X 3/4"
110 X 3/4"
40 X 1"
110x1"
50 X l /2"
110 X 1 l /4"
50 X 3/4"
110 X 1 l /2"
SQ X 1"
110 X 2"
110 X 2 l /2"
110 X 3"
125 X 1 /2"
125 X 3/4"
125 X 1"
125 X 1 l /4"
125 X 1 l /2"
125 X 2"
125 X 2 l /2"
125 X 3"
125 X 4"
160 X l /2"
160 X 3/4"
160 X 1"
* High Pressure 160 X 1 1 /4"
160x1 1 /2"
160 X 2"
160 X 2 1 /2"
J
160 X 3"
160 X 4"
2QQ X 2"
Al Rayyan Nursery Company CL!,..C.IJjJI cil!JJI c..ULw..o CI..=:)J--,W
C.r 2053029968 2053029968 -=, •._,.,
A�AYYAN
FEATURES·
The dnpper has the following advantages:
• Turbulant flow to resist blockage
• Dripper line stability provided by logs in base
• Clean easily due to its removable cap
• 4mm Barbep inlet
APPLICA TION
Landscaping, Orchards, Vineyards, Green houses, Shrubs.
C Code#
CTK4
Discharge UH
4L/HR
--
�
1.00
4.00
Pressure (Bar)
1.5
4.80
2.00
5.40
CTKB BL/HR 9.00 9.00 10. 50
1
CTKP 2 2L/HR 2.05 2.10 2.10
CTKP 4 4L/HR 4.10 4.10 4.20
CTKP B BL/HR 8.20 8.20 8.30
info@alrayyanksa.com
Al Rayyan Nursery Company CJ..!----C.IJµI ul!JJI cUl..w.o CI..=>J---W
C.r 2053029968 2053029968 ..:., .._,..,
A�AYYAN
r:uc: In.JI c-·.1t,JJI <.lil.uLQ O pi,
LJ.:WJ19'-1cw' �u1J
unJ.14L:>gJg
PE. PIPES & FITTINGS
J
info@alrayyanksa.com
info@alrayyanksa.com
info@alrayyanksa.com
info@alrayyanksa.com
info@alrayyanksa.com
info@alrayyanksa.com
info@alrayyanksa.com
Irrigation pipe and fittings ALAWASAIL company
info@alrayyanksa.com
Technical Material Submittal
info@alrayyanksa.com
CONTENTS Page Nu.
• Alwasail pressure compensating THABIT DRIPLINE 3
• ROTORS 87
• SPRAYS 121
• nozzles 132
• Controllers 162
www.alwasail.com
info@alrayyanksa.com
o@
www.alwasail.com
info@alrayyanksa.com
Thabit PC Dripline with flat internal dripper
Manufacturer Company:
Thabit PC Dripline is an effective and economical choice for your drip irrigation network and now comes in a wide
range of standard pipe and tape sizes.Thatmanagesyouofmoreflexibleirrigationdesign.
Model:
Features:
info@alrayyanksa.com
Thabit PC Dripline Dimensions
pipe
Pipes
ter mm 0.7 0.8 0.9 1.0 1.1 1.2
ter mm 8 10 12 15 18 24 36
16 13.8
17 16.1 17 16.1
18 15.7 22 21.2
20 17.6
25 24.7
Enclosure:
Product brochure.
www.alwasail.com
info@alrayyanksa.com
in
in
Applications
Features
Specifications
®
• Manufactured from the finest raw materials that
provide durability and long-lasting performance
I PAGE15
• Excellent emission uniformity
• Excellent flow coefficient
• Low friction losses due to the ultra-slim design of the emitter
• Special labyrinth design ensures high turbulent flow of the
water
• High UV resistance
• Resistant to all nutrients used in agriculture
in
Thabit PC Dripline is an effective and economical
choice for your drip irrigation network and now
comes in a wide range of standard pipe and tape
sizes that allow you more flexible irrigation design.
P
,
Flow Chart
- 1,0 1/h
- 1,5 1/h
- 2,0 1/h
0,0 0,5 1,0 1,5 2,0 2,5 3,0 - 2,4 1/h
3,5 4,0 4,5
Pressure@ Emitter (bar) - 3,8 1/h
17mm
Flat Pipe Dimensions
Nominal Inner Wall Thickness MM
18mm 15.7mm
Diamete Diameter 8 10 12 15 18 24 36
r
20mm 17.6mm
in
25mm 24.7mm
www.alwasail.com
info@alrayyanksa.com
Hodhod PC Online Emitter
The most versatile and easy-to-install Pressure Compensating emitter for a greatvarietyofapplications.
MODELS:
info@alrayyanksa.com
Features:
- UltrasonicWeldingTechnology
The advanced welding process of Hodhod PC eliminates the problem all online emitters eventually face, leakage
between the body and the cover of the emitter. In our emitter, this is prevented by a parallel formation and
welding of the cover, around the edge of the body of Hodhod PC making it impossible to leak regardless of the
climatic or pressure conditions.
info@alrayyanksa.com
Hodhod Online PC EmitterFlow Curves
info@alrayyanksa.com
Applications
• Precision Irrigation • Gardening
• Uneven terrain • Landscaping
• Greenhouses & Nurseries • Hydroponics
• Orchards • Soilless culture
Features
• Pressure Compensating (PC)
Hodhod PC emitters incorporate a silicone membrane which enables the delivery of precise and equal amounts
of water over a broad pressure range. Designed for precision irrigation needs,ranging from a home to the most
advanced hydroponic application.
• Drain (D) and Non-Drain (ND) Options
With the Non-Drain system of Hodhod PC, the pipe remains full of water during irrigation intervals, ensuring
immediate & uniform irrigation along the pipe. Non-Drain emitters eliminate drainage, refill effects, and improve
efficiency in pulse irrigation. In order to achieve the Non-Drain function, emitter opens at 0.30 & closes at 0.20 bar.
info@alrayyanksa.com
• Ultrasonic Welding Technology
The advanced welding process of Hodhod PC eliminates the problem all online emitters eventually face, leakage
between the body and the cover of the emitter. In our emitter, this is prevented by a parallel formation & welding of
the cover, around the edge of the body making it impossible to leak regardless of climate or pressure conditions.
Specifications
• Color Coded for wide range of flow rates 2.0, 4.0, 8.0 & 24 L/H
• For installation in pipes 12-32 mm & wall thickness from 0.9- 1.2mm
• Wide pressure compensation range
• Cross-shaped water inlet
• Wide & accurate water passages along the special labyrinth
design that ensures highly turbulent flow
• Continuous self-cleaning mechanism ensures non-clogging
• Resistant to standard nutrients used in agriculture & UV Part Numbering System
resistant WS-HDPC - x - D/ND
• Injected molded emitters with excellent Coefficient of Variation WS-HDPC Hodhod Online Emitter
(CV)
• Can be installed manually exactly where they are required X Emitter Flow
• The number of emitters can be increased to increase water D/ND Drain/Non Drain
supply
• Design allows the installation of manifold outlet with multiple
outputs
• One type of outlet suitable for 3mm internal diameter micro-
tube and press-fit nipple connectors
® I PAGE19
Flow Chart
2
- 4,0 1/h
0
8,0 1/h
0,0 0,5 1,0 1,5 2,0 2,5 3,0
3,5 4,0 4,5 - 24,0 1/h
Pressure@ Emitter (bar)
Drain Hodhod
PC Emitter J
Non Drain
Hodhod PC
Emitter j
Applications
• Precision Irrigation • Gardening
• Uneven terrain • Landscaping
• Greenhouses & Nurseries • Hydroponics
• Orchards • Soilless culture
Features
• Pressure Compensating (PC)
Hodhod PC emitters incorporate a silicone membrane which enables the delivery of precise and equal amounts
of water over a broad pressure range. Designed for precision irrigation needs,ranging from a home to the most
advanced hydroponic application.
• Drain (D) and Non-Drain (ND) Options
With the Non-Drain system of Hodhod PC, the pipe remains full of water during irrigation intervals, ensuring
immediate & uniform irrigation along the pipe. Non-Drain emitters eliminate drainage, refill effects, and improve
efficiency in pulse irrigation. In order to achieve the Non-Drain function, emitter opens at 0.30 & closes at 0.20 bar.
• Ultrasonic Welding Technology
The advanced welding process of Hodhod PC eliminates the problem all online emitters eventually face, leakage
between the body and the cover of the emitter. In our emitter, this is prevented by a parallel formation & welding of
the cover, around the edge of the body making it impossible to leak regardless of climate or pressure conditions.
Specifications
• Color Coded for wide range of flow rates 2.0, 4.0, 8.0 & 24 L/H
• For installation in pipes 12-32 mm & wall thickness from 0.9- 1.2mm
• Wide pressure compensation range
• Cross-shaped water inlet
• Wide & accurate water passages along the special labyrinth
design that ensures highly turbulent flow
info@alrayyanksa.com
Flow Chart
2
- 4,0 1/h
0
8,0 1/h
0,0 0,5 1,0 1,5 2,0 2,5 3,0
3,5 4,0 4,5 - 24,0 1/h
Pressure@ Emitter (bar)
Drain Hodhod
PC Emitter J
Non Drain
Hodhod PC
info@alrayyanksa.com
Alwasail Barbed Fittings for Driplines
Manufacturer:
Features:
Specifications:
info@alrayyanksa.com
Applications Features
Alwasail fittings have a wide application field including • Reduced installation costs with quick, easy assembly.
irrigation, water industries, telecommunication, & mining. • Made from high-quality virgin Polypropylene
They are all manufactured from tough engineering Injection material. Suitable for reuse.
material to withstand UV radiation, corrosion, severe • High rigidity/heat resistance & low moisture
environmental conditions, pressure, temperature, absorbency.
mechanical & hydraulic loads, etc. • Available to be produced with different
standards, thread & material upon request.
Specifications • Designed to comply with pipe manufactured to
Australian Standard AS2698.1 & European standard.
• Available • Comply with statutory regulations in the USA &
Europe for PE pipe from 4mm to 32mm dia
regarding materials intended to come in contact with
• Nominal Working pressure: 3
bar food stuff.
• BSP threading connection
• Packing: Standard Carton Box Size • Approved by TUV CERT ISO9002 Certification
Body of RWTUVGMPH.
I
tubing or dnpline with barbed
couplings.
Elbows
info@alrayyanksa.com
MALE ADAPTERS CONNECTORS
TailxBSP male (mmxinch) LinexLine (mmxmm)
NOM. ITEM QTY PER WElGHT NOM. ITEM QTY PER WEIGHT
DIAMETER CODE CARTON KGS DIAMETER CODE CARTON KGS
;,:.
7.30 ,.
� ..-(""'' -::_." ...........
'
ELBOWS ,,.
6.35
LinexLine (mmxmm)
5.20 NOM. ITEM QTY PER WEIGHT
DIAMETER CODE CARTON KGS
nfo info@alrayyanksa.com
Quick coupling valve:
Manufacturer Company:
Model:
Features:
Specifications:
nfo
info@alrayyanksa.com
Quick Coupling
Valves and Accessories
Applications Models
Often used in garden centers, the connection points can be WSI-AE-QCV34
used to connect bench sprinklers or for hand. Alwasail also Description: Quick Coupling Valve
offers accessories such as a brass key and a swivel elbow. Dimensions: 3/4” Female BSP
Features thread inlet size
WSI-AE-QCV10
• One piece of solid brass construction for durability.
• Stainless steel spring prevents leakage. Description: Quick Coupling Valve
Dimensions: 1” Female BSP
• Drain hole in the body to minimize debris collection.
thread inlet size
• Specially designed grommet.
• Lid auto closes when not in use. WSI-AE-QCE34
• Brass spiral turn and lock key. Description: Quick Coupling Elbow
• Inbuilt handle designed for gripping. Dimensions: 3/4”x 3/4” Female x Male,
Inlet x Outlet, BSP thread inlet size
• Optional locking cover.
• Elbow with leakage free design. WSI-AE-QCE10
Specifications Description: Quick Coupling Elbow
Dimensions: 1”x 1” Female x Male, Inlet
• Cover made of Thermo-Plastic Elastomer x Outlet, BSP thread inlet size
• Maximum working pressure – 145 PSI
WSI-AE-QCK34
• Male - female threaded inlet connection at elbow
Description: Quick Coupling Key
• 360-degree rotation elbow
Dimensions: 3/4” Top Pipe Thread Male BSP
RIV
Rubinetterie italiane velatta SPA
Components LTD
ITALY
Model:
Enclosure:
Product brochure.
info@alrayyanksa.com
Series
info@alrayyanksa.com
RIV 2010
Gate valve F/F
full bore - steel
handwheel
info@alrayyanksa.com
Technical data
Materials
1 Body Brass 1/2" - 2" CW617N<BR> 2"1/2 - 6"
CB754S
2 Wedge Brass CB754S
3 Gasket Fibre
5 Gasket P.T.F.E.
7 O-Ring NBR
Notes The max. working pressure (PN) means at a room temperature of about 23°C.
info@alrayyanksa.com
Valve Boxes
Manufacturer Company
Alwasail Industrial Company
Qassim, KSA
Models:
- WS-VB-610 (Round 6”)
- WS-VB-910 (Round 9”)
- WS-VB-1419 (Rectangular 12” Standard)
- WS-VB-1320 (Rectangular 12” Jumbo)
- WS-VB-1324 (Rectangular 15” Super Jumbo)
- WS-VB-1370 (Rectangular 18” Super Jumbo)
Features:
• Thicker wall dimensions for more strength & durability.
• Reinforced covers for heavier loads.
• Reinforced ribs offer exceptional sidewall strength.
• Overlapping covers prevent dirt and grass from getting in between cover and body.
UV inhibitors prevent discoloration and cracking.
Product brochure
info@alrayyanksa.com
Valve boxes:
Manufacturer Company:
SERIES 610:
Item Description Material
Code
6” Round Valve Box - Complete(GR Body & GR Cover) WS-GB 610-G
6” Round Valve Box Cover - Green WS-GB 610-CG
6” Round Valve Box Body - Green WS-GB 610-BG
SERIES 910:
Item Description Material
Code
10” Round Valve Box - Complete(GR Body & GR Cover) WS-VB 910-G
10” Round Valve Box Cover - Green WS-VB 910-
CG
10” Round Valve Box Body - Green WS-VB 910-BG
S.S. Bolt & Nut M8x80mm (Optional) WS-VB 910-
SSB
SERIES 1111:
Item Description Material
Code
11” Round Valve Box – Complete (GR Body & GR Cover WS-VB 1111-G
11” Round Valve Box - Cover Green WS-VB 1111-
CG
11” Round Valve Box - Body Green WS-VB 1111-
BG
S.S. Bolt & Nut M8x80mm (Optional) WS-VB 1111-
SSB
SERIES 1419:
Item Description Material
Code
12” Standard Rectangular Valve Box - Complete (GR Body & GR Cover) WS-VB 1419-G
12” Standard Rectangular Valve Box - Cover Green WS-VB 1419-
CG
12” Standard Rectangular Valve Box - Body Green WS-VB 1419-
BG
S.S. Bolt & Nut M8x80mm (Optional) WS-VB 1419-
SSB
info@alrayyanksa.com
SERIES 1419 (6” Standard Extension Low Profile Valve Box):
6” Standard Extension Valve Box - complete (GR Body & GR Cover WS-VBEX 1419-G
info@alrayyanksa.com
SERIES 1320:
Item Description Material Code
12” Jumbo Rectangular Valve Box - Complete (GR Body & GR Cover) WS-VB 1320-G
12” Jumbo Rectangular Valve Box - Cover Green WS-VB 1320-CG
12” Jumbo Rectangular Valve Box - Body Green WS-VB 1320-BG
S.S. Bolt & Nut M8x80mm (Optional) WS-VB 1320-
SSB
SERIES 1324:
Item Description Material Code
15” Big Jumbo Rectangle Valve Box - Complete (GR Body & GR Cover) WS-VB 1324-G
15” Big Jumbo Rectangle Valve Box - Cover Green WS-VB 1324-CG
15” Big Jumbo Rectangle Valve Box - Body Green WS-VB 1324-BG
S.S. Bolt & Nut M8x80mm (Optional) WS-VB 1324-
SSB
SERIES 1730:
Item Description Material Code
18” Super Jumbo Rectangle Valve Box - Complete (GR Body & GR Cover) WS-VB 1730-G
18” Super Jumbo Rectangle Valve Box - Cover Green WS-VB 1730-CG
18” Super Jumbo Rectangle Valve Box - Body Green WS-VB 1730-BG
S.S. Bolt & Nut M8x80mm (Optional) WS-VB 1730-
SSB
Features:
Features
• Thicker wall dimensions for more strength & durability.
• Reinforced covers for heavier loads.
• Reinforced ribs offer exceptional sidewall strength.
• Overlapping covers prevent dirt and grass from
getting in between cover and body.
• UV inhibitors prevent discoloration and cracking.
Specifications
• High-impact, high-density/polyethylene structure.
• 6", 10" & 11" sizes are available in boxes
• 12", 15" & 18" Sizes are available in round or rectangle.
ed No Cracks Green
ed No Cracks Green
SERIES 610
Box
6" Round Valve
ITEM CODE QUANTITY
DESCRIPTION
WS-GB 610-G 90 Per Carton
5- 3/4"
6" Round Valve Box - Complete (GR
Body & GR Cover)
WS-GB 610-CG 90 Per Carton
6" Round Valve Box Cover - Green
WS-GB 610-BG 90 Per Carton
6" Round Valve Box Body - Green
8-3/8"
Item Code Pallet Size CM (L x Bx H) Qty. Per Pallet Weight Per Unit Net Weight Per Pallet
WS-VB-610 130 x 110 x 164 360 1.0692 kg 384.912 kg
SERIES 910
10" Round Valve Box 1 • 1/8"
10" Round Valve Box Cover - Green WS-VB 910-CG 36 Per Carton
10" Round Valve Box Body - Green WS-VB 910-BG 36 Per Carton 10·
S.S. Bolt & Nut M8x80mm (Optional) WS-VB 910-SSB 36 Per Carton
Item Code Pallet Size CM (L x Bx H) Qty. Per Pallet Weight Per Unit Net Weight Per Pallet
WS-VB-910 130 x 110 x 164 144 1.2788 kg 184.1472 kg
SERIES 1111
11" Round Valve Box
DESCRIPTION ITEM CODE QUANTITY
11" Round Valve Box - Complete
WS-VB 1111-G 135 Per Carton
(GR Body & GR Cover)
info@alrayyanksa.com
® I PAGE29
SERIES 1419
12" Standard Rectangular Valve Box
DESCRIPTION ITEM CODE QUANTITY
12" Standard Rectangular Valve Box WS-VB 1419- G 90 Per Carton
- Complete (GR Body & GR Cover)
S.S. Bolt & Nut M8x80mm (Optional) WS-VB 1419-SSB 90 Per Carton
Item Code Pallet Size CM (Lx Bx H) Qty. Per Pallet Weight Per Unit Net Weight Per Pallet
WS-VB-1419 130 x 110 x 220 90 4.179 kg 376.11 kg
SERIES 1419
6" Standard Extension Low Profile Valve Box
DESCRIPTION ITEM CODE QUANTITY
6" Standard Extension Valve Box - WS-VBEX 1419-G 90 Per Carton
Complete (GR Body & GR Cover)
S.S. Bolt & Nut M8x80mm (Optional) WS-VBEX 1419-SSB 90 Per Carton
Item Code Pallet Size CM (Lx Bx H) Qty. Per Pallet Weight Per Unit Net Weight Per Pallet
WS-VB-1419 130 x 110 x 220 90 2.3146 kg 210.744 kg
SERIES 1320
12" Jumbo Rectangular Valve Box
DESCRIPTION ITEM CODE QUANTITY
12" Jumbo Rectangular Valve Box WS-VB 1320- G 60 Per Carton
- Complete (GR Body & GR
Cover)
WS-VB 1320-CG 60 Per Carton
12" Jumbo Rectangular Valve Box
- Cover Green
WS-VB 1320-BG 60 Per Carton
12" Jumbo Rectangular Valve Box
- Body Green
S.S. Bolt & Nut M8x80mm (Optional) WS-VB 1320- SSB 60 Per Carton
Item Code Pallet Size CM (Lx Bx Qty. Per Pallet Weight Per Unit Net Weight Per
H) Pallet
WS-VB-1320 130 x 110 x 220 60 5.564 kg 333.84 kg
SERIES 1320
6" Jumbo Extension Valve Box
DESCRIPTION ITEM CODE QUANTITY
6" Jumbo Extension Valve Box - WS-VBEX 1320- G 60 Per Carton
Complete (GR Body & GR Cover)
S.S. Bolt & Nut M8x80mm (Optional) WS-VBEX 1320- SSB 60 Per Carton
Item Code Pallet Size CM (Lx Bx H) Qty. Per Pallet Weight Per Unit Net Weight Per Pallet
WS-VB-1320 130 x 110 x 220 60 3.554 kg 213.24 kg
SERIES 1324
15" Big Jumbo Rectangular Valve Box
DESCRIPTION ITEM CODE QUANTITY
15" Big Jumbo Rectangle Valve Box WS-VB 1324- G 18 Per Carton
- Complete (GR Body & GR Cover)
15" Big Jumbo Rectangle Valve Box WS-VB 1324-CG 18 Per Carton
- Cover Green
15" Big Jumbo Rectangle Valve Box WS-VB 1324-BG 18 Per Carton
- Body Green
S.S. Bolt & Nut M8x80 mm (Optional) WS-VB 1324-SSB 18 Per Carton
Item Code Pallet Size CM (L x B x H) Qty. Per Pallet Weight Per Unit Net Weight Per Pallet
WS-VB-1324 130 x 110 x 220 18 13.418 kg 241.524 kg
SERIES 1730
18" Super Jumbo Rectangular Valve Box
DESCRIPTION ITEM CODE QUANTITY
18" Super Jumbo Rectangle Valve Box WS-VB 1730- G 16 Per Carton
- Complete (GR Body & GR Cover)
18" Super Jumbo Rectangle Valve Box WS-VB 1730-CG 16 Per Carton
- Cover Green
18" Super Jumbo Rectangle Valve Box WS-VB 1730-BG 16 Per Carton
- Body Green
S.S. Bolt & Nut M8x80 mm (Optional) WS-VB 1730-SSB 16 Per Carton
Item Code Pallet Size CM (L x B x H) Oty. Per Pallet Weight Per Unit Net Weight Per Pallet
WS-VB-1730 130 x 110 x 220 16 17.665 kg 282.64 kg
Air Release and Vacuum Valves:
Manufacturer Company:
Model:
Features:
Specifications:
info@alrayyanksa.com
nfo
Applications Features
• Straight flow body with higher flow rates.
Typically used in landscape irrigation at filtration and fertilization
stations, as well as downstream of main control valves to ensure • Aerodynamic full-body kinetic shield
that any entrained air in the water system is released • Dynamic sealing prevents leakage under 1.5 PSI.
automatically in order to maximize system performance. • Fully corrosion, chemical, and fertilizer resistant.
• Lower maintenance and increased life span.
Principles of Operation Specifications
WSI-AV2plus- 225 PSI 5 PSI 0-360
• Pipeline Filling 2
When water enters the valve chamber, the buoyant float causes
the kinetic orifice to close. The unique aerodynamic structure
prevents the float from closing before water reaches the valve.
• Pressurized Operation
When the pipeline is pressurized, air accumulates in the upper part
of the air valve chamber, causing the float to gravitate downward.
The automatic orifice opens, releasing the air. The water level and
float rise after the air is discharged, causing the automatic close.
• Pipeline Draining
A negative differential pressure is created when a pipeline is
drained, causing atmospheric air to push the float downward. The
kinetic orifice remains open, allowing air into the valve chamber
and preventing a vacuum from forming in the pipe.
• Surge Protection (anti-slam)
The anti-slam device is attached to the outlet. It partially closes the
valve’s outlet in the event of a pressure surge. Rising air pressure in
the valve causes the approaching water column to slow down.
• Inflow Protection
A normally closed check device installed on the valve’s outlet that
prevents atmospheric air from entering the valve.
Valve Data
Model Max Working Sealing Air Outtake Air
Code Pressure Pressure (M³/H) Intake
(M³/H)
WSI-AV1-1 225 PSI 5 PSI 0-280 -280-0
WSI-AV2-2 225 PSI 5 PSI 0-360 -360-0
nfo info@alrayyanksa.com
Direct burial decoder cable (UF: Underground Feeder)
(To be used between irrigation controller and electrical solenoid valves)
Manufacturer Company:
Model:
Specifications:
The Decoder cable shall be 2 twisted single conductors insulated wires (with 10 cm lay), so that they stay
together during the installation process and offer some opposition to electrical flow during lightning
strikes.
The decoder cable shall be employed for direct burial use.
The conductor shall be of solid annealed copper meeting the requirements of ASTM Specifications B-3.
The Decoder Cable shall have a temperature rating of between -55°C and 60°C.
The insulation shall be of the solid extracted polyethylene with a thickness of 1.52 mm.
The Decoder cable is available in 14 AWG, 12AW, and 10AWG.
Enclosure:
Product brochure.
info@alrayyanksa.com
1.0 SCOPE:
2.1 Conductor:
Solid annealed copper meeting the
requirements of ASTM specifications B-3.
2.3 Insulation:
Solid extracted polyethylene Insulation
thickness shall be 0.060” (1.52 mm). Conductor
colors are as follows and shall be twisted with
a 4” lay.
12 RED BLUE
MESC 12
10 RED BLUE
MESC 10
info@alrayyanksa.com
M E S C
Middle East Specialized Cables
UF - DIRECT BURIAL IRRIGATION WIRE TWISTED PAIR
Application : Single conductor type UF wire is employed for direct burial use in
commercial sprinkler and irrigation systems, Golf courses, Public parks, Plantations and commercial
produce farms.
CONSTRUCTION
Conductor Solid annealed copper conductor as per ASTM B-3.
Printing (Example) Direct Burial Decoder cable, PE, 600V, 14AWG Manufactured by Middle East
Specialized Cables Co. (MESC), Riyadh in Saudi Arabia
TECHNICAL DATA
Working voltage 600 Volts.
info@alrayyanksa.com
MIDDLE EAST SPECIALIZED CABLES (MESC) reserves the right to make changes to the product described in this data sheet
without prior notice. MESC does not assume any liability which may occur due to the use of the products described herein. The
information contained in this data sheet is the proprietary property of MESC and may not be used, reproduced or disclosed to
others, in whole or in part, without the written authorization of
MESC.
Model:
Material Code
Features:
Specifications:
The device, DBR Direct Bury Splice Kit, shall splice and effectively moisture seal two or more
conductors. The electrical connector shall be a Scotchlok® R.
The device shall be installed per manufacturer’s instructions and all applicable codes.
info@alrayyanksa.com
Irrigation Disc Filters:
Manufacturer:
Description:
With excellent technology, ALWASAIL’s disc filters focus on multiple filtration grades, high efficiency, and
large volume filtration advantage. Additionally, we provide various filters with different pipe sizes and
flow rates & filtration grades (20~400 micron) to satisfy different application needs. They are simple
cleaning with a well-designed structure.
Features:
• Compact structure available in narrow space;
• Gasket set in the lid;
• Innovative grooved discs design retains large amounts of solids;
• Threaded closure system, easy and safe; Low pressure loss;
• Resistant to chemical products;
• Easy installation, easy maintenance;
• Equipped with auxiliary connections;
• Preset 2 ports for connecting pressure gauge.
Enclosure:
Product brochure.
info@alrayyanksa.com
asail
Irrigation Disc Fi
ron mi ron
(40 mesh) (75 mesh)
.... ....
YTYPE
With excellent technology, ALWASAl s disc
filters focus on multiple filtration grades,
high efficiency, and water-saving advan
tage. They are simple cleaning with a
well-designed structure.
Application
Y type disc filters are applicable to low flow
rate water filtering for agriculture irrigation
and landscape irrigation. With built-in pres
sure pipeline, Y type disc filter can efficiently
filter out particles.
BSP/NPT Connection
Pressure Gauges
Connections
Modular Filter:
T interchangeable elements
in different filtration grades
Wide Filtering
Surface
outlet
'
' Effective closure system
· ------ allows discs to be loosened
but not lost during cleaning.
Features
• Compact structure available in narrow space;
• Gasket set in the lid;
• Innovative grooved discs design retains large amounts of solids;
• Threaded closure system, easy and safe; Low pressure loss;
• Resistant to chemical products;
• Easy installation, easy maintenance;
• Equipped with auxiliary connections;
• Preset 2 ports for connecting pressure gauge.
Models & Specifications
Filtering
CONNECTION FILTRATION GRADE Max Flow WEIGHTS
MODEL Surface
BSP (MESH) (Kg)
(GPM)
WSI-F020-Y 120 22 0.39
1" 120 26
1/2" 40/75/120/150 88 20
40/75/120/150 110 25
Head Losses1/2" 75/120 Dimension
132 30 2.60
• YTYPE FILTER HEAD LOSS( 130 micron/ 120 mesh)
75/120 154 35 70
psi/ bar
7.25 0.50 ------------------------------------------------------------------
X
2.90 0.20
2 15 25 (m3/hl
8.8 66 110 (gpm)
Note: The flow rate will fluctuate with different water quality.
MODEL
mm in in mm in
173 mm 186 83
173 186 83
230 9 250 120
230 9 250 120
260 290 140
260 290 140
330 13 360 168
330 13 360 168
Material
HOUSING Maximum Pressure 8 Bar/
FILTERING ELEMENTS 116 Psi
Maximum Temperature
60 CI 140 F
0
info@wise-engg.com
6- Products Warranty
info@alrayyanksa.com
7- compliance sheet
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@alrayyanksa.com
info@alrayyanksa.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com
info@wise-engg.com