Professional Documents
Culture Documents
Imagepress Server g100
Imagepress Server g100
This installation procedure is written in Japanese and English. The installation procedure for Japan model is described in Japanese and one for the other models is
described in English. These procedures are different from each other. Follow the procedure corresponding to the installed model.
- Japanese: The installation procedure for Japan model
- English: The installation procedure for the other models except for Japan model
この設置手順書には、和文と英文の設置手順が記載されている。和文では日本モデル用の設置手順が記載されており、英文では日本モデル以外のその他のモデル用の設
置手順が記載されている。それぞれの設置手順は異なっているので、モデルに応じた手順に従うこと。
・和文: 日本モデル用設置手順
・英文: 日本モデル以外のその他のモデル用設置手順
ENGLISH 日本語
Before Connection > Installing the license 2
Securing space for installation [4] Cross Ethernet [5] Shield Ethernet [6] Open I/F PCB X 1
Cable X 1 Cable (3.0 m) X1
A space of 200 mm or more is required from the back of this equipment.
Rear
F-1-2
NOTE: [10] Open I/F PCB [11] Card Spacer X 1 [12] Screw (TP; M3x6) X 4
[3] Power Cord: The connector has a different shape depending on locations. Mounting Plate X 1
Use the correct power code to match the location/area of installation.
Make sure not to leave unused power code at the site.
The parts ([10] to [12], and [13] to [16]) are packed in single bags.
• [10] to [12]: To be used when installing the Open I/F PCB.
• [13] to [16]: To be used when installing the PS Unit.
F-1-3
[13] Wire Saddle X 4 [14] Screw with [15] Stepped Screw Turning OFF the power of the host machine
Toothed Washer (M4) X 2
(Binding; M4x8) X 4 Check that the main power switch is OFF.
1) Turn OFF the main power switch of the host machine.
2) Be sure that display in the Control Panel and the lamp of the main power supply are turned
off, then disconnect the power plug.
[16] Screw (TP; M3x6) X 6 Check when Connecting the Power Plug to an Outlet
Use 2 of them When connecting the power plug of this equipment to an outlet, be sure to use an outlet of a
system different from that of the host machine.
F-1-5
Installation Procedure
2) Disconnect the Reader Communication Cable and release the 2 Lock Levers.
4x
F-1-7
2x
F-1-8
4) Remove the Face Plate (the removed Face Plate will not be used). 6) Remove the Bypass PCB (the removed Bypass PCB will not be used).
• 2 Screws (The removed screws will be used in step 8.) • 2 Screws (The removed screws will be used in step 8.)
• 1 Connector
NOTE:
Ask the user to store the Face Cover, in case it is needed in the future. NOTE:
Ask the user to store the Bypass PCB, in case it is needed in the future.
2x
2x
1x
F-1-9
F-1-11
5) Remove the screw and replace it with the Card Spacer (the removed screw will be used in
step 8). 7) Install the Open I/F PCB Mounting Plate.
• 1 Screw (TP; M3 x 6)
1x
1x
TP
M3x6
F-1-10
F-1-12
8) Install the Open I/F PCB. 10) Turn over the 2 Lock Levers, and push in and secure the Main Controller PCB 2.
• 1 Connector • 2 Screws (Install in order of bottom and top.)
• 5 Screws (Use the screws removed in steps 4, 5, and 6.)
• 3 Screws (TP; M3 x 6) CAUTION:
Be sure to perform the work in the order from 1 to 5 in the figure because the connector
of the Main Controller PCB 2 may not be connected.
1x
2x
2x
6x
TP
M3x6
F-1-13
9) Release the 2 Lock Levers in the direction of the arrows, and uniformly push in the Main
Controller PCB 2 with both hands until it stops. F-1-15
Install the Main Controller PCB 2 while paying attention not to trap cables.
12) Connect the Interface Cable to the Open I/F PCB.
1x
Lock
Lever
F-1-14 F-1-16
CAUTION:
When installing the Box Left Cover, be careful not to trap cables. 2x
4x
F-1-18
2) Hook the Support Plate to the screw (right side) loosened in step 1, and install it in the
F-1-17
direction of the arrow..
• 1 Screw (TP; M3 x 6)
1x
Screw
TP
M3x6
Screw Support Plate
F-1-19
3) Hook the Support Plate to the screw (left side) loosened in step 1, and install it in the 5) Install the 2 Stepped Screws (M4) to the Support Plate.
direction of the arrow.
• 1 Screw (TP; M3 x 6)
2x
1x
Stepped Screw
Stepped Screw
M4 Support Plate
Stepped Screw
6) Remove the 8 screws of the PS Unit. (the removed screw will be used in step 7)
F-1-22
F-1-20
7) Install the PS Unit Fixation Plate. 9) Remove the 2 Face Seals of the Rear Lower Cover (the removed Face Seals will not be
• 4 Screw (Use the screws removed in steps 6.) used).
CAUTION:
Be sure to install it in the correction direction.
4x
F-1-25
8) Hook the PS Unit to the 2 Stepped Screws (M4) tightened in step 5, and install it.
• 4 Screws with Toothed Washer (Binding; M4 x 8)
4x
F-1-24
11) Connect the Interface Cable to the PS Unit. 13) Close the HDD Cover.
• 2 Wire Saddles
1x
2x
F-1-27
F-1-29
12) Open the HDD Cover, connect one end of the Cross Ethernet Cable to the host
machine and then connect another end to the PS Unit.
1x
1x
F-1-28
15) Remove the label, and connect the Power Cord. 17) Connect the power plug to the outlet of the host machine.
16) Secure the Power Cord and the Shield Ethernet Cable in place.
• 2 Wire Saddles
18) Connect the power plug to the outlet of the PS Unit.
CAUTION:
• Use the correct power code to mach the location/area of installation. Make sure not CAUTION:
to leave unused power code at the site. Be sure to use an outlet of a system different from that of the host machine.
• Be sure to use the network cable with Category 5e or higher. In addition, a sealed
type (STP cable) is recommended. When using the non-sealed type (UTP cable),
it may influence the surrounding electronic equipments via network cable.
19) Turn ON the main power switch of the host machine.
2x
20) "Turn ON the main power of the host machine again." is displayed on the touch panel,
turn OFF the main power switch of the host machine.
F-1-30
1) Select Settings/Registration > [Function Settings] > [Web Access] > [Settings] > [Privacy 1) Select [Fiery] from the main menu on the host machine's LCD.
Policy and Regulations], and set the following items to "ON".
• Full Screen: ON
• Hide Buttons in Toolbar: ON
• Hide Address in Toolbar: ON
F-1-33
CAUTION:
Use single-byte upper case to enter F of "Fiery.1". Use single-byte lower case to enter
other characters.
F-1-32
F-1-34
F-1-37
F-1-35
Check that the items in the General Setup are set, and perform [Save Changes] even if there
is no change. The setting will not be completed unless [Save Changes] is pressed.
4) Check the settings of server, network, printer and PDL. When making each setting, the
setting will not be completed unless [Save Changes] is pressed.
F-1-38
F-1-36
1) Select [Fiery] from the main menu on the host machine's LCD.
F-1-39
6) The confirmation screen will appear, and then press [Reboot Now].
F-1-41
F-1-40
F-1-42
Installation Procedure > Checking the Operation After Making the Settings 15
Installation Procedure > Executing image Quality Adjustment 16
Connecting to the Network
3) Select [Info] > [Print Pages] > [PS Test Page].
Ask the network administrator to connect to the network, make settings and output the test
print.
Refer to "Configuration and Setup" in User's Manual for details of checking work.
2
3
Executing image Quality Adjustment
1 Execute the image quality adjustment shown below at installation. (Refer to "Installation" in
Service Manual for host machine.)
• Auto Gradation Adjustment
• Register Paper to Adjust
• Execution of Correct Shading
F-1-43
• Auto Correct Color Tone Settings (Only when installing the Image Reader Unit)
4) Press [Yes].
F-1-44
本設置手順書の見方について 接続前の準備
注意 :
ライセンスのインストール
以下は日本モデル用の設置手順が記載されている。 同梱されているライセンス証書を取出し、事前にライセンスキーを取得しておく。 EFI コントロー
日本モデル以外の設置手順は、 英文設置手順に従うこと。 ラーの設定は、 本体の操作部から Web ブラウザで行う。
以下の手順でライセンスの登録を行う。
イラスト内のシンボルマークについて
1) 管理者 ( モード ) で本体にログインする。
本手順書では、 よく行う動作などについてシンボルマークで表現している。
工場出荷時のパスワードは下記である。
ビス
・ システム管理部門 ID : 7654321
・ システム管理暗証番号 : 7654321
1x 1x 1x 1x
200 mm以上 本機
背面
同梱部品の確認
メモ :
[10] オープンI/F基板 [11] カードスペーサー X 1 [12] ビス (TP; M3x6) X 4
[10] ~ [12]、 [13] ~ [16] はそれぞれ 1 つの袋にまとめて梱包されている。
取付け板 X 1
・ [10] ~ [12]: Open I/F PCB 取付け時に使用する。
・ [13] ~ [16]: PS ユニット取付け時に使用する。
F-1-3
同梱部品の確認 18
取付け概略図 19
[13] ワイヤサドル X 4 [14] 歯付き座金付ビス [15] 段ビス (M4) X 2 本体主電源 OFF の確認事項
(バインド; M4x8) X 4
本体の主電源が OFF であることを確認する。
1) 本体の主電源スイッチを OFF する。
2) 操作パネルの表示と主電源ランプが消えたことを確認してから電源プラグを外す。
電源接続時の確認
[16] ビス (TP; M3x6) X 6
本機の電源プラグをコンセントに差込む場合、 本体と別系統のコンセントを使用すること。
2本使用
取付け概略図
F-1-4
F-1-5
取付け概略図 19
設置手順 > オープン I/F 基板の取付け 20
4x
F-1-8
4) 目隠し板を外す ( 外した目隠し板は使用しない )。
・ ビス 2 本 ( 外したビスは手順 8) で使用する )
F-1-6
メモ :
外した目隠し板はユーザーに渡し、 保管して頂くこと。
2) リーダー通信ケーブルを外し、 ロックレバー 2 箇所を解除する。
1x 2x
F-1-9
F-1-7
1x
1x
TP
M3x6
F-1-10
F-1-12
6) バイパス基板を外す ( 外したバイパス基板は使用しない )。
・ ビス 2 本 ( 外したビスは手順 8) で使用する ) 8) オープン I/F 基板を取付ける。
・ コネクタ 1 箇所 ・ コネクタ 1 箇所
・ ビス 5 本 ( 手順 4)、 5)、 6) で外したビスを使用する )
メモ : ・ ビス (TP; M3 x 6) 3 本
外したバイパス基板はユーザーに渡し、 保管して頂くこと。
1x
2x
2x
6x
1x
TP
M3x6
F-1-13
F-1-11
9) ロックレバー 2 箇所を矢印の方向に解除し、 メインコントローラー基板 2 を突当たるまで両 10) ロックレバー 2 個を倒して、 さらにメインコントローラー基板 2 を押込み、 固定する。
手で均等に押込む。 ・ ビス 2 本 ( 下、 上の順に取付ける )
注意 : 注意 :
ケーブル類をはさみこまないように注意して、 メインコントローラー基板 2 を取付ける。 メインコントローラー基板 2 のコネクタが接続されていない場合があるため、 図の 1 ~ 5
の順番で確実に作業を行うこと。
2x
ロック
レバー
F-1-14
F-1-15
11) リーダー通信ケーブルを取付ける。
1x
F-1-16
PS ユニットの取付け
13) インターフェースケーブルをボックス左カバーの穴に通して、 ボックス左カバーを取付ける。
・ ビス 4 本
1) 後上カバーの目隠しシール 2 枚を剥し、 ビス 2 本を緩める ( 剥した目隠しシールは使用し
注意 : ない )。
ボックス左カバーを取付ける際は、 ケーブル類を挟まないように注意すること。
2x
4x
F-1-18
1x
ビス
TP
M3x6
ビス 支持板
F-1-19
2x
1x
段ビス
段ビス
M4 支持板
支持板 段ビス
ビス
TP
支持板
M3x6
ビス F-1-22
F-1-20
ビス 8x
2x
F-1-23
F-1-21
注意 :
取付ける向きを間違えないこと。
4x
F-1-26
4x
歯付き
座金付ビス F-1-27
バインド; M4x8
F-1-25
1x
2x
F-1-28
F-1-30
12) HDD カバーを開き、 クロスイーサネットケーブルを本体と PS ユニットに接続する。
1x
1x
F-1-29
1x
22) CNT-TYPE の値が “454” であることを確認する。
・ サービスモード ( レベル 1) > COPIER > OPTION > INT-FACE > CNT-TYPE
F-1-31
ウェブブラウザーの表示範囲設定 設置後の設定
1) 設定 / 登録 > [ ファンクション設定 ] > [ ウェブブラウザー ] > [ 仕様設定 ] > [ 機能制限設 1) 本体の液晶表示部上のメインメニューから [Fiery] を選択する。
定 ] から以下項目を 「ON」 に設定する。
・ 最大表示モードの ON/OFF : ON
・ ツールバーのボタン部の表示制限 : ON
・ ツールバーのアドレス部の表示制限 : ON
F-1-34
注意 :
Fiery.1 の F は半角大文字で入力する。 それ以外は半角小文字で入力する。
F-1-33
F-1-35
F-1-38
F-1-36
F-1-39
F-1-37
設置後の動作確認
5) 全ての設定完了後、 [ 設定終了 ] を押下する。
以下の手順で、 テストページ、 設定ページを出力し、 本体と本機の接続および本機の設定を
確認する。
F-1-40
F-1-42
F-1-41
7) PS ユニットが再起動される ( 約 10 分 )。
F-1-43
ネットワークへの接続
3) [ 情報 ] > [ ページの印刷 ] > [PS テストページ ] を選択する。
ネットワーク管理者にネットワークへの接続、 設定およびテストプリントを依頼する。 確認作業
は、 ユーザーマニュアルの 「設定管理」 を参照して行う。
2
3
画質調整の実施
1
設置時には、 以下の画質調整を行う ( 本体サービスマニュアル参照 )。
・ 自動階調補正
・ 補正用紙登録
・ 濃度ムラ補正
・ 自動色調補正 ( イメージリーダーユニット設置時のみ )
F-1-44
4) [ はい ] を押下する。
F-1-45