Professional Documents
Culture Documents
Sony Hdr-cx405 Hdr-cx440 Hdr-pj410 Hdr-pj440 1st-Edition SM
Sony Hdr-cx405 Hdr-cx440 Hdr-pj410 Hdr-pj440 1st-Edition SM
HDR-CX405
HDR-CX440
HDR-PJ410
HDR-PJ440
SERVICE MANUAL
1st Edition
警告
このマニュアルは, サービス専用です。
お客様が, このマニュアルに記載された設置や保守, 点検, 修理などを行うと感電や火災,
人身事故につながることがあります。
危険をさけるため, サービストレーニングを受けた技術者のみご使用ください。
WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440
注意 FÖRSIKTIGHET!
CAUTION
PAS PÅ
Danger of explosion if battery is incorrectly replaced.
Fare for eksplosion, hvis batteriet ikke udskiftes
Replace only with the same or equivalent type rec-
korrekt.
ommended by the manufacturer.
Udskift kun med et batteri af samme eller tilsvarende
When you dispose of the battery, you must obey the
type, som er anbefalet af fabrikanten.
law in the relative area or country.
Når du bortskaffer batteriet, skal du følge
lovgivningen i det pågældende område eller land.
ATTENTION
HUOMIO
Il y a danger d’explosion s’il y a remplacement incor-
rect de la batterie. Remplacer uniquement avec
Räjähdysvaara, jos akku vaihdetaan virheellisesti.
une batterie du même type ou d’un type équivalent
Vaihda vain samanlaiseen tai vastaavantyyppiseen,
recommandé par le constructeur.
valmistajan suosittelemaan akkuun.
Lorsque vous mettez la batterie au rebut, vous devez
Noudata akun hävittämisessä oman maasi tai
respecter la législation en vigueur dans le pays ou la
alueesi lakeja.
région où vous vous trouvez.
FORSIKTIG
VORSICHT
Eksplosjonsfare hvis feil type batteri settes i.
Explosionsgefahr bei Verwendung falscher Batterien. Bytt ut kun med samme type eller tilsvarende
Batterien nur durch den vom Hersteller empfohlenen anbefalt av produsenten.
oder einen gleichwertigen Typ ersetzen. Kasser batteriet i henhold til gjeldende avfallsregler.
Wenn Sie die Batterie entsorgen, müssen Sie die
Gesetze der jeweiligen Region und des jeweiligen
Landes befolgen.
⊼ᛣ
བᵰᤶⱘ⬉∴ϡℷ⹂ˈህӮ᳝⟚⚌ⱘॅ䰽DŽ
াᤶৠϔ㉏ൟࠊ䗴ଚ㤤ⱘ⬉∴ൟোDŽ
໘⧚⬉∴ᯊˈᖙ乏䙉ᅜⳌ݇ഄऎᆊⱘ⊩ᕟDŽ
Note: 注意:
Be sure to keep your PC used for service and checking of this 修理時に使用するパソコンは,ウィルス検出ソフトが常にアッ
unit always updated with the latest version of your anti-virus プデートを行っているパソコンを使用してください。もし,修
software. In case a virus affected unit was found during service, 理を行うセット,もしくはパソコンがウィルスに感染している
contact your Service Headquarters. 事が判明した場合は,ソニーグループ内は社内技術相談窓口に,
特約店様は特約店様専用電話窓口(修理窓口)にご相談くださ
い。
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered UNLEADED SOLDER
connections. Check the entire board surface for solder splashes This unit uses unleaded solder.
and bridges. Boards requiring use of unleaded solder are printed with the lead free
2. Check the interboard wiring to ensure that no wires are “pinched” mark (LF) indicating the solder contains no lead.
or contact high-wattage resistors. (Caution: Some printed circuit boards may not come printed with
3. Look for unauthorized replacement parts, particularly transistors, the lead free mark due to their particular size.)
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs : LEAD FREE MARK
of deterioration. Point them out to the customer and recommend Be careful to the following points to solder or unsolder.
their replacement.
5. Check the B+ voltage to see it is at the values specified. • Set the soldering iron tip temperature to 350 °C approximately.
6. Flexible Circuit Board Repairing If cannot control temperature, solder/unsolder at high temperature
• Set the soldering iron tip temperature to 350 °C approximately. for a short time.
• Do not touch the soldering iron on the same conductor of the Caution: The printed pattern (copper foil) may peel away if the
circuit board (within 3 times). heated tip is applied for too long, so be careful!
• Be careful not to apply force on the conductor when soldering Unleaded solder is more viscous (sticky, less prone to
or unsoldering. flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440
Model Information
MODEL GROUP
Projector Model: PJ410/PJ440
Non Projector Model: CX405/CX440
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5
Table of Contents
Model Information
Manual Structure
1. Trouble Shooting
2. Service Note
3. Adjustment
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 1
4-2-5. Cabinet (R) Section (Projector Model). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-13
4-2-6. LCD Section (Projector Model). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-15
4-2-7. Cabinet (R) Section (Non Projector Model). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-19
Revision History
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 2
Manual Structure
This manual describes the information items that premise the service based on the components parts assuming use of
system and service engineers.
Related manuals
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 3
Section 1
Trouble Shooting
If an error occurs in this unit, the self-diagnosis function starts working and a code consisting of one alphabet and a
four-digit number appears on the LCD. Classification of persons in charge, classification of faulty blocks, and details
of errors can be checked by referring to this indication of five alphanumeric characters in the self-diagnosis code table.
The history of past errors can be checked in “Usage and Diag record” on the DATA tab of the Adjust Manual.
The self-diagnosis function is also described in the operation manual.
The boards and functions used in this model are mentioned in the following table.
Board Function
CM board Imager
MM board Internal memory
WF board Wireless LAN module
PJ board Projector
VC board CPU, Power, Lens drive, 3-axis angular velocity sensor, Other function
Self-diagnosis Code
Repaired by:
Continued
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 1-1
Self-diagnosis Code
Repaired by:
E 41 00 Abnormality of the wireless LAN The peripheral circuit of between CPU and wireless LAN
module or CPU module may be faulty.
Replace the board that contains this peripheral circuit.
E 61 00 Difficult to adjust focus Turn power off and turn power on again. When this error is
(Cannot initialize focus) not cleared, the focus control signal for the lens block may
be faulty.
Check whether this error is due to the lens or the board.
Replace the faulty lens or board.
E 61 10 Zoom operations fault Turn power off and turn power on again. When this error is
(Cannot initialize zoom lens) not cleared, operate the zoom lever and check following
items.
• When zooming is performed, the zoom control signal
for the lens block may be faulty.
• When zooming is not performed, the zoom motor
drive circuit may be faulty.
Check whether this error is due to the lens or the board.
Replace the faulty lens or board.
E 61 11 Focus or zoom fault Check both C: 32: 60 and E: 61: 10 of the self-diagnosis
code.
E 61 30 Reset position detection error on the Turn the power on to open lens barrier. Disconnect the bat-
stepper iris initializing tery or power cord, and then connect again. And confirm
that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive cir-
cuit in lens drive block. If iris blades work normally, con-
firm that they are closing completely and confirm following
items.
• Case of the iris blades do not close normally. Replace
the lens block.
• Case of “E: 61: 30” is appeared and iris blades closed
completely. Confirm that communication with lens
block is normal.
• Case of LCD is not displayed normally, check that
connection between imager board and main board.
• Case of LCD is displayed normally, replace the lens
block.
E 61 31 Error in detection of the Reset Posi- Check the signal line connection between the lens block and
tion at the time of Stepper IR Filter the lens control circuit.
initialization Check whether this error is due to the lens or the board.
Replace the faulty lens or board.
E 62 00 Handshake correction function does The peripheral circuit of the PITCH angular velocity sensor
not work well. (With PITCH angu- may be faulty.
lar velocity sensor output stopped) Replace the board that contains this peripheral circuit.
E 62 01 Handshake correction function does The peripheral circuit of the YAW angular velocity sensor
not work well. (With YAW angular may be faulty.
velocity sensor output stopped) Replace the board that contains this peripheral circuit.
E 62 02 Abnormality of IC for steadyshot. Check signal line connections from CPU through hand-
shake correction IC to PITCH/YAW drive.
When there is no problem with the connections, replace the
board that contains this peripheral circuit.
E 62 03 Communication error of handshake The steadyshot circuit may be faulty.
correction IC and CPU Replace the board that contains this peripheral circuit.
E 62 04 Image vibration correction during The image vibration angular velocity sensor (ROLL SEN-
handshake function does not work. SOR) peripheral circuit may be faulty.
Replace the board that contains this peripheral circuit.
Continued
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 1-2
Self-diagnosis Code
Repaired by:
*1: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items. After
the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
*2: Function of this code is not provided in this unit.
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 1-3
1-2. Method of Coping with Shift Lens Error
Identify the cause of the problem (lens or VC-1023 board), and replace the faulty lens or the VC-1023 board.
Start the Adjust Manual in the Adjust Station and execute the “Measure to E:62:11/12” on the SERVICE tab.
Then confirm that the shift lens moves. If it does not move, replace the lens block.
Identify the cause of the problem (lens or VC-1023 board), and replace the faulty lens or the VC-1023 board.
Start the Adjust Manual in the Adjust Station and execute the “Measure to E:62:11/12” on the SERVICE tab.
Then confirm that the shift lens moves. If it does not move, replace the lens block.
Identify the cause of the problem (lens or VC-1023 board), and replace the faulty lens or the VC-1023 board.
Check the connection between the lens block and VC-1023 board.
Identify the cause of the problem (lens or VC-1023 board), and replace the faulty lens or the VC-1023 board.
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 1-4
Section 2
Service Note
• Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
• Do not touch the conductive side of flexible boards with bare hands.
• Plug in a flexible board straight, fully into the connector until it reaches the end inside.
OK NG NG
(The flexible board was plugged in (The flexible board was plugged in (The flexible board was not plugged in
straight and completely) crooked.) completely.)
Flexible Flexible
Board Flexible Flexible Board Flexible
Board Board Board
Reference line Reference line
Flexible
Reference line Board
• When opening the connector's holder in direction A, do not open it with excessive force.
Holder
A
Connector
A Flexible Board
• When closing the connector's holder, press it evenly while pushing a flexible board in direction B.
Holder
Connector
Flexible Board
Insulation side
• Make sure that the flat cable and flexible board are not cracked or bent at the contact end.
• The proper way to disconnect a connector is to grab the connector instead of the wires. If you pull on the wires,
they might be broken.
• The proper way to connect a connector is to grab the connector instead of the wires. If you push on the wires, they
might be broken.
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 2-1
2-2. Power Supply during Repairs
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 2-2
2-3. Precaution on Replacing the VC-1023 Board
The board for repair is not recorded the information peculiar to a model. Therefore the following data are needed to
write.
Note
The [LOAD AND WRITE] function in “ADJUSTMENT DATA BACKUP” on the DATA tab in the Adjust Manual
overwrites all data of the unit. Therefore execute the [LOAD AND WRITE] before performing the following operation.
The destination data stored in the repairing board is different from the destination setting stored in the board before
replacement in some cases.
When the board has been replaced with a repairing board, be sure to set the destination.
When you replace to the repairing board, get the USB serial number from the former one.
The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have
been written.
These IDs have not been written in a new repairing board. Therefore, after the board has been replaced, be sure to write
these IDs to a new repairing board.
Before replacing the board with a repairing board, be sure to extract the following data from the former one.
• Fixed value (that shows irradiation performance of the projector)
• Serial number of the projector unit
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 2-3
2-3-5. Update of MAC Address
When a board that contains Wi-Fi has been replaced or when replacing a board that contains the main IC (CPU), the
IC’s unique number (MAC address) must be reloaded.
1. Start the Adjust Manual in the Adjust Station and execute the “Wireless LAN Setting (MAC Address)” on the
ADJUST tab.
2. Operate the unit to initialize of SSID/PW.
Applicable parts:
• VC-1023 BOARD, COMPLETE (SERVICE)
• WF-1004 BOARD, COMPLETE
Note
After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required.
Accordingly, download the Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach
it to the set when returning the set to customer.
Unless these script files are executed, the following symptoms may appear. Make sure execute the above script files.
• The internal memory is not recognized as a media.
• The management file saved in the internal memory cannot be repaired.
• The internal memory cannot be formatted.
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 2-4
START
Execute
Select the "USB CONNECT" to establish the "[][]DdmMmcMakePartition_v[].vbe"
the connection
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 2-5
2-4. Checking the Wi-Fi Function
After this unit has been disassembled and reassembled, check the Wi-Fi function.
Required equipment:
Windows PC or smartphone with Wi-Fi interface
Procedure:
1. Turn on the power of the unit and enable the Wi-Fi function.
(Upon completion of the preparation for Wi-Fi connection, the password for Wi-Fi connection is displayed.)
2. Confirm on the PC or the smartphone that the unit is detected as a connectable wireless network.
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 2-6
2-5. Note on Replacing Projector Unit (Projector Model)
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
If you have received an indication on the projector’s projection function from the customer, check defective part
according to the following flowchart.
When a defective part has been clarified, repair the projector according to the check result.
Note
The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down. Wipe the lens gently with a soft cloth such as
a cleaning cloth or glass cleaning cloth.
Note
Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with
water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning
cloth, as they will damage the lens surface.
Indicated defective
projector received
NG NG
Measure brightness. A Inspect projector
( 2) LED. ( 1)
OK OK
- Replace projector unit (light emitting block). (*1)
- Replace PJ board. (*1)
- Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
- Fixed value input
Enter the number on the label attached to the unit.
- Serial number input
LD40Syywwnnnnn Enter the red part.
NG
Inspect projector
LED. ( 1)
OK
END
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 2-7
Projector problem checking procedure (indication on brightness)
Indicated defective
projector received
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
No
Indication on
brightness
B
Yes
NG
Measure brightness.
( 2)
OK A
NG
Inspect projector
LED. ( 1)
OK
NG
Measure brightness.
( 2)
OK
END
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 2-8
Section 3
Adjustment
For adjusting these models, the Adjust Station and the Adjust Manual are required.
Adjust Station
It is the software to start up Adjust Manual for each model.
The installer of the Adjust Station and the installation manual are attached, be sure to confirm the contents of them.
Adjust Manual
It is the software to adjust and check digital cameras and camcorders for service.
The installer of the Adjust Manual and the installation manual are attached, be sure to confirm the contents of them.
Note
Be sure to install Adjust Station first.
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 3-1
Section 4
Replacement of Main Parts
L Top Assy
BT Panel
CX440/PJ410/PJ440
Control Switch Block
MM-102 Board
• FP-2060 Flexible Board
BT Lid Assy
Lens Block
• CM-1004 Board
• FP-2190 Flexible Board
VC-1023 Board
View Position
Top View
Back View
Left View
Front View
Right View
Bottom View
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-1
4-2. Disassembly
• Refer to “Overall Section-1 (Projector Model)” on exploded view for Ref. No.
[1] 4
Overall Section-2
[3] 3 #12
(Projector Model)
#12
A
#12
(Claws)
(Claws) #2
#2 [5] 5
A #2
#2
{1}
[4] 2 [2] 1
Disassembly Places
機種によって形状がイラストと異なる場合があります。
[1] #12 X 1
Left View
#12
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-2
[2] Open the LCD {1} → #2 X 2
Bottom View
Back View
{1} #2
#2
#2
#12
Back View
#12
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-3
4-2-2. Overall Section-1 (Non Projector Model)
• Refer to “Overall Section-1 (Non Projector Model)” on exploded view for Ref. No.
Overall Section-2
[1] 54
[3] 53 #12
(Non Projector Model)
#12
A
#12
(Claws)
(Claws) #2
#2 [5] 55
A #2
#2
{1}
[4] 52 [2] 51
Disassembly Places
機種によって形状がイラストと異なる場合があります。
[1] #12 X 1
Left View
#12
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-4
[2] Open the LCD {1} → #2 X 2
Bottom View
Back View
{1} #2
#2
#2
#12
Back View
#12
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-5
4-2-3. Overall Section-2 (Projector Model)
• Refer to “Overall Section-2 (Projector Model)” on exploded view for Ref. No.
119
120 (Note 1)
126 118
#140 #12 #2
[2] 113
117
D BT901
#12 A 108
#140 (including CP001
[3] 109 (CMOS imager)) 121 112
[1]111
#172 #172
107
110 106
SP901
PJ440 104
Cabinet (R) Section
ns 123 (Projector Model)
(Note 2) 105 B
[1] ns
(Note 2) C
103
ns
(Note 2) #12 B
PJ410: CEN, CEH,
A
E35, E37, EA8 116
#12 D
#2
122 C
#2
MIC901
ns
ns
[4] 102
125
124
101 125
Note 1
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-6
Note 2
MM-102基板またはFP-2060フレキシブル基板のどちらかが故
障した場合は,下記の3部品を全てセットから取り外して破棄し
てください。
・MM-102基板
・FP-2060フレキシブル基板
・ネジ
上記3部品は無い場合でも,セットの動作に影響はありません。
部品を取り外すとデモ画面は使用できなくなります。
Disassembly Places
機種によって形状がイラストと異なる場合があります。
[1] #140 X 1
Left View
#140
[2] #2 X 1 → #12 X 1
Top View
#2 Left View
#12
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-7
[3] #12 X 1 → Open the LCD {1} → #2 X 1
Top View
Right View
#12 #2
{1}
[4] #2 X 1 → #12 X 1
Top View
Right View
#12
#2
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-8
Notes on Assembling the Overall Section-2
How to distinguish the side of Optical Filter Block facing to Lens Device
The one side of the Optical Filter Block has treated with IR cut coating.
Mount the Optical Filter Block facing the IR cut coated side to the lens
device. Distinguish the IR cut coated side from the other by applying the
fluorescent light to the Optical Filter Block in the dark place (cut off the
outside light).
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-9
4-2-4. Overall Section-2 (Non Projector Model)
• Refer to “Overall Section-2 (Non Projector Model)” on exploded view for Ref. No.
175
176 (Note)
177 174
#140 #12 #2
[2] 161
173 D BT901
CX440
#140 #12 A 158
[3] (including CP001 160
159 (CMOS imager)) 166
[1]167
#172 #172
157
168 156
SP901 B
CX440 154
170 Cabinet (R) Section
155 (Non Projector Model)
151
#12 C
153
B
169 #12
MIC901 A
ns 165
ns
D
#2
C
#2
Note
Disassembly Places
機種によって形状がイラストと異なる場合があります。
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-10
[2] #2 X 1 → #12 X 1
Top View
#2 Left View
#12
Right View
#12 #2
{1}
[4] #2 X 1 → #12 X 1
Top View
Right View
#12
#2
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-11
Notes on Assembling the Overall Section-2
How to distinguish the side of Optical Filter Block facing to Lens Device
The one side of the Optical Filter Block has treated with IR cut coating.
Mount the Optical Filter Block facing the IR cut coated side to the lens
device. Distinguish the IR cut coated side from the other by applying the
fluorescent light to the Optical Filter Block in the dark place (cut off the
outside light).
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-12
4-2-5. Cabinet (R) Section (Projector Model)
• Refer to “Cabinet (R) Section (Projector Model)” on exploded view for Ref. No.
210
211
ns LCD Section
(Projector Model)
#288
(Note 1)
209 208
(Note 3)
(Claws)
#2
205
#2
203
201 204
202
(Claws)
(Claws)
#30
Note 1
このねじは再利用することができません。
サービス対応時に一度でも外した場合は新品のねじと交換
してください。
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-13
Note 2
非常に弱い 弱い 指サック着用のこと
(持ってはいけない) (取り扱い注意)
レバー
レンズ部 銅板 フレキ接点
シート 銅板 コネクタ部
プロジェクターを使用した後は,プロジェクターユニットが
熱くなっています。特に銅板の部分は高温になります。
部品を交換する時は,温度が下がってから作業を行なって
ください。
Note 3
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-14
4-2-6. LCD Section (Projector Model)
• Refer to “LCD Section (Projector Model)” on exploded view for Ref. No.
264
#288
(Note 1)
262
259
263
(Note 2)
261 265 #2
(Note 4)
(14 x 4.5 mm)
(Claws)
260
258
257
LCD901 252
256
#11
255
253
254
ns
BH4600
(Note 3)
BT4600
(Note 3) 251
Note 1
このねじは再利用することができません。
サービス対応時に一度でも外した場合は新品のねじと交換
してください。
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-15
Note 2
マグネットを取付ける際は,マ−キング面を図の位置にあわせ
てください。
Marking
マーキング
Note 3
Note 4
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-16
Notes on Assembling the LCD Section
Adhesive tape
Adhesive tape
Adhesive tape Valley fold
Mountain fold
Mountain fold
Adhesive tape
Adhesive tape
FP-2193
Flexible Board
FP-2184
Flexible Board
Adhesive tape
Valley fold
Valley fold
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-17
2 Roll the FP-2184/2193 Flexible Board 2 times
in the Hinge Assy as shown in the figure below.
Flexible Board
Hinge Assy
2 Times
FP-2184/2193
Flexible Board
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-18
4-2-7. Cabinet (R) Section (Non Projector Model)
• Refer to “Cabinet (R) Section (Non Projector Model)” on exploded view for Ref. No.
314
ns 315
#288
(Note 1) 317
#288
ns (Note 1) 308
310
(Note 4) 312 #2
313
(Note 2)
#2 316
(Note 5)
(14 x 4.5 mm)
311 (Claws)
307
306
302 ns 305
#2
(Claws)
BH4500
(Note 3)
BT4500 303
(Note 3)
301
(Claws)
(Claws)
Note 1
このねじは再利用することができません。
サービス対応時に一度でも外した場合は新品のねじと交換
してください。
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-19
Note 2
マグネットを取付ける際は,マ−キング面を図の位置にあわせ
てください。
Marking
マーキング
Note 3
Note 4
Note 5
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-20
Notes on Assembling the Cabinet (R) Section
Adhesive tape
Adhesive tape
Adhesive tape Valley fold
Mountain fold
Mountain fold
Adhesive tape
Adhesive tape
FP-2193
Flexible Board
FP-2184
Flexible Board
Adhesive tape
Valley fold
Valley fold
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-21
2 Roll the FP-2184/2193 Flexible Board 2 times
in the Hinge Assy as shown in the figure below.
Flexible Board
Hinge Assy
2 Times
FP-2184/2193
Flexible Board
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 4-22
Section 5
Repair Parts List
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some The components identified by mark or dotted line with
differences from the original one. mark are critical for safety.
• Items marked “*” are not stocked since they are seldom Replace only with part number specified.
required for routine service. Some delay should be anticipated
Les composants identifiés par une marque sont
when ordering these items.
critiques pour la sécurité.
• The mechanical parts with no reference number in the
Ne les remplacer que par une pièce portant le numéro
exploded views are not supplied.
spécifié.
• Due to standardization, replacements in the parts list may be
different from the parts specified in the diagrams or the
components used on the set. CAUTION
• ns: Not supplied part. Danger of explosion if battery is incorrectly replaced.
• CAPACITORS: Replace only with the same or equivalent type.
uF: μF Dispose of used batteries according to the instructions.
• COILS
uH: μH ⌞ᝅ
• RESISTORS
ྲ᷌⭥⊐ᴤᦒнᖃՊᴹ⠶⛨ড䲙DŽ
All resistors are in ohms.
ਚ㜭⭘਼ṧ㊫රᡆㅹ᭸㊫රⲴ⭥⊐ᶕᴤᦒDŽ
METAL: metal-film resistor
࣑ᗵ᤹➗䈤᰾༴㖞⭘ᆼⲴ⭥⊐DŽ
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS The components identified by mark contain confidential
In each case, u: μ, for example: information.
uA... : μA... , uPA... : μPA... , uPB... : μPB... , Strictly follow the instructions whenever the components
uPC... : μPC... , uPD... : μPD... are repaired and/or replaced.
• Color Indication of Appearance Parts Destroy and discard the prescribed board and IC
Example: after they are replaced.
(SILVER) : Cabinet’s Color
(Silver) : Parts Color Les composants identifiés par le symbole contiennent
des informations confidentielles.
Suivez scrupuleusement les instructions chaque fois
qu'un composant est remplacé et / ou réparé.
Veuillez détruire et éliminer les circuits imprimés et / ou
les circuits intégrés que vous avez remplacés.
ḽ䇼ᴿⲺݹԬऻᵰᇼؗᚥȾ
ᴪᦘᡌ㔪ݹؤԬᰬθ䈭ћṲ䚫ᆾ示Ⱦ
ᴪᦘⲺ⭫䐥ᶵૂ,&θᓊҾԛᣛᓕȾ
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5-1
5-2. Exploded View
[1] 4
Overall Section-2
[3] 3 #12
(Projector Model)
#12
A
#12
(Claws)
(Claws) #2
#2 [5] 5
A #2
#2
{1}
[4] 2 [2] 1
Ref. No.
or Q'ty Part No. SP Description
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5-2
Overall Section-1 (Non Projector Model)
Overall Section-2
[1] 54
[3] 53 #12
(Non Projector Model)
#12
A
#12
(Claws)
(Claws) #2
#2 [5] 55
A #2
#2
{1}
[4] 52 [2] 51
Ref. No.
or Q'ty Part No. SP Description
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5-3
Overall Section-2 (Projector Model)
119
120 (Note 1)
126 118
#140 #12 #2
[2] 113
117
D BT901
#12 A 108
#140 (including CP001
[3] 109 (CMOS imager)) 121 112
[1]111
#172 #172
107
110 106
SP901
PJ440 104
Cabinet (R) Section
ns 123 (Projector Model)
(Note 2) 105 B
[1] ns
(Note 2) C
103
ns
(Note 2) #12 B
PJ410: CEN, CEH,
A
E35, E37, EA8 116
#12 D
#2
122 C
#2
MIC901
ns
ns
[4] 102
125
124
101 125
101 A-2067-220-A CABINET BLOCK ASSY (217) 120 A-1992-200-A WF-1004 BOARD, COMPLETE
102 A-2069-583-A VC-1023 BOARD, COMPLETE (SERV- 121 1-889-222-11 FP-2201 FLEXIBLE BOARD
ICE) (PJ440)
102 A-2073-564-A VC-1023 BOARD, COMPLETE (SERV- 122 4-282-293-01 SHEET (ST (381)), SHIELD
ICE) (PJ410) 123 4-568-328-01 SHEET (478), VC RADIATION
103 4-476-262-01 RETAINER (453), HDMI 124 4-568-562-01 SHEET (T1) (478), RADIATION
104 1-889-184-11 FP-2190 FLEXIBLE BOARD 125 4-568-563-01 SHEET (T2) (478), RADIATION
126 4-489-010-01 SHEET (ANT), ADHSIVE
105 8-848-900-01 DEVICE, LENS LSV-1610A
106 1-856-432-21 FILTER BLOCK, OPTICAL BT901 1-780-826-11 * TERMINAL BOARD, BATTERY
107 4-436-733-01 RUBBER (1610), SEAL MIC901 1-542-948-11 MICROPHONE UNIT
108 A-1903-090-A CM-1004 BOARD, COMPLETE SP901 1-858-075-41 SPEAKER (1.8CM)
109 A-1998-288-A CABINET ASSY (449), INNER #2 2-635-562-31 SCREW (M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
110 1-887-155-11 FP-2060 FLEXIBLE BOARD (PJ410:
CEN, CEH, E35, E37, EA8/PJ440) #140 2-635-562-01 SCREW (M1.7)
111 A-2066-983-A MM-102 BOARD, COMPLETE (PJ440) #172 2-178-410-01 TITE (UB TITE) 1.4
112 1-838-712-61 CABLE, BUILT-IN USB
113 1-492-709-11 SWITCH BLOCK, CONTROL (PS45300)
116 4-476-291-01 BATTERY (441), DUMMY
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5-4
Overall Section-2 (Non Projector Model)
175
176 (Note)
177 174
#140 #12 #2
[2] 161
173 D BT901
CX440
#140 #12 A 158
[3] (including CP001 160
159 (CMOS imager)) 166
[1]167
#172 #172
157
168 156
SP901 B
CX440 154
170 Cabinet (R) Section
155 (Non Projector Model)
151
#12 C
153
B
169 #12
MIC901 A
ns 165
ns
D
#2
C
#2
151 A-2067-220-A CABINET BLOCK ASSY (217) 172 4-568-563-01 SHEET (T2) (478), RADIATION
152 A-2063-953-A VC-1023 BOARD, COMPLETE (SERV-
ICE) (CX440) 173 1-889-592-11 AN-1006 FLEXIBLE BOARD (CX440)
152 A-2073-563-A VC-1023 BOARD, COMPLETE (SERV- 174 1-889-209-11 FP-2200 FLEXIBLE BOARD (CX440)
ICE) (CX405) 175 A-2040-416-A NFC BLOCK ASSY (14Y_TERA) COMP
153 4-476-262-01 RETAINER (453), HDMI (Note) (CX440)
154 1-889-184-11 FP-2190 FLEXIBLE BOARD 176 A-1992-200-A WF-1004 BOARD, COMPLETE (CX440)
177 4-489-010-01 SHEET (ANT), ADHESIVE
155 8-848-900-01 DEVICE, LENS LSV-1610A
156 1-856-432-21 FILTER BLOCK, OPTICAL BT901 1-780-826-11 * TERMINAL BOARD, BATTERY
157 4-436-733-01 RUBBER (1610), SEAL MIC901 1-542-948-11 MICROPHONE UNIT
158 A-1903-090-A CM-1004 BOARD, COMPLETE SP901 1-826-837-91 SPEAKER (1.3CM)
159 A-1998-288-A CABINET ASSY (449), INNER #2 2-635-562-31 SCREW (M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
160 1-838-712-61 CABLE, BUILT-IN USB
161 1-492-709-11 SWITCH BLOCK, CONTROL (PS45300) #172 2-178-410-01 TITE (UB TITE) 1.4
165 4-476-291-01 BATTERY (441), DUMMY
166 1-889-222-11 FP-2201 FLEXIBLE BOARD
167 A-2066-983-A MM-102 BOARD, COMPLETE (CX440)
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5-5
Cabinet (R) Section (Projector Model)
210
211
ns LCD Section
(Projector Model)
#288
(Note 1)
209 208
(Note 3)
(Claws)
#2
205
#2
203
201 204
202
(Claws)
(Claws)
#30
Ref. No.
or Q'ty Part No. SP Description
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5-6
LCD Section (Projector Model)
264
#288
(Note 1)
262
259
263
(Note 2)
261 265 #2
(Note 4)
(14 x 4.5 mm)
(Claws)
260
258
257
LCD901 252
256
#11
255
253
254
ns
BH4600
(Note 3)
BT4600
(Note 3) 251
Ref. No.
or Q'ty Part No. SP Description
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5-7
Cabinet (R) Section (Non Projector Model)
314
ns 315
#288
(Note 1) 317
#288
ns (Note 1) 308
310
(Note 4) 312 #2
313
(Note 2)
#2 316
(Note 5)
(14 x 4.5 mm)
311 (Claws)
307
306
302 ns 305
#2
(Claws)
BH4500
(Note 3)
BT4500 303
(Note 3)
301
(Claws)
(Claws)
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5-8
5-3. Fuse
4.45V
F003
VC-1023 BOARD (SIDE B)
5V
F001
4.45V
F002
Primary side
Ref. No.
or Q'ty Part No. SP Description
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5-9
5-4. Accessories
This Item is not supplied with the unit as an accessory, but it is prepared as a service part.
When the customer requests printed one, ask Head Quarter.
941
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 5-10
Section 6
Frame Schematic Diagrams
Frame Wiring (1/2)
CX440/PJ410/PJ440
LENS BLOCK
CN2302
3 4
1 2
1 39
1
25
1
1 18
CN8101
26
24
24
CN2301
1 18
FP-2200
FP-2190 FLEXIBLE BOARD ET2301
FLEXIBLE
BOARD FP-2060
FLEXIBLE
BOARD
24 1
18 1
BUILT-IN
USB CABLE CONTROL
1 39 SWITCH
BLOCK
(PS45300)
CHARGE
MIC901 39 1
1
2 38
39
14 13 20 19 26 25
38 2 12 1 18 1 24 1
CN4012
61
CN4005 CN4902
6 1
UNIT 5 1
8
CN4000
21 1
Projector Model
1
2
CN4901
CN3201 CN9000 2 60
CN4001
CN4011
19 1 19 1 CN7101 1 61
10
9
2318 2 20 2318 2 19 12
2 1 22 21 22 21
4 3
1
FP-2201 BT901
FLEXIBLE
BOARD
FLEXIBLE
BOARD
FLEXIBLE BOARD S BATTERY (Page 6-2) (Page 6-2)
TERMINAL
Non Projector Model Projector Model
10
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 6-1
Frame Wiring (2/2)
VC-1023
BOARD
(SIDE B)
A
(Page 6-1)
1 61
CN4500
402 38
41 S4501
1 39
(MULTI-SELECTOR)
3841
39
CN8040
S4500
402
1
FP-2184
FLEXIBLE BOARD BT4500
1 39 LITHIUM 2.7 INCH LCD901
BATTERY WIDE COLOR (LCD MODULE)
LCD
Projector Model
VC-1023 1
BOARD
(SIDE B)
B
(Page 6-1)
1 61 FP-2106
FLEXIBLE BOARD
45
43
2 44
PJ-1009 BOARD PJ-1009 BOARD
1
PROJECTOR
CN5503
(SIDE A) (SIDE B)
UNIT
CN8502
41
1
46 42
45
10
45 1
44 2
CN8504
CN8503
2 60
1 59
1 CN3700 59
522 5053 S4601
1 51
(MULTI-SELECTOR)
CN4600
41
39
38
S4600
FP-2193 1 51
FLEXIBLE BOARD
402
1
S4602
PROJECTOR
BT4600
LITHIUM 2.7 INCH LCD901
BATTERY WIDE COLOR (LCD MODULE)
LCD
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 6-2
Revision History
HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440 3
HDR-CX405 (U2)
HDR-CX405 (CA2)
HDR-CX405 (CEN)
HDR-CX405 (CEH)
HDR-CX405 (CEL)
HDR-CX405 (E23)
HDR-CX405 (E35)
HDR-CX405 (E37)
HDR-CX405 (EA8)
HDR-CX405 (AU2)
HDR-CX405 (CN1)
HDR-CX405 (KR2)
HDR-CX405 (HK1)
HDR-CX440 (U2)
HDR-CX440 (E23)
HDR-PJ410 (CEN)
HDR-PJ410 (CEH)
HDR-PJ410 (CEL)
HDR-PJ410 (E35)
HDR-PJ410 (E37)
HDR-PJ410 (EA8)
HDR-PJ410 (AU2)
HDR-PJ410 (CN1)
HDR-PJ410 (KR2)
HDR-PJ440 (UC2)
HDR-PJ440 (E23)
HDR-PJ440 (E35)
HDR-PJ440 (KR2) Printed in Japan
HDR-PJ440 (HK1) Sony Corporation 2015. 01 08
9-896-718-11 © 2015