Professional Documents
Culture Documents
VRX932LAP
VRX932LAP
Technical Manual
JBL VRX932LAP/230
SPECIFICATIONS
ACOUSTIC & ELECTRICAL SPECIFICATIONS: • Cabinet: Enclosure (Not For Sale)
• DPC-2 Internal Amplification Output • Grille: 352282-001
(at normal load): 1750 Watts Peak, 875 Watts Continuous • Low Frequency 2262FF, 305 mm (12 in) dual voice coil
• Frequency Response: 75 Hz - 20 kHz (±3 dB) Transducer: Differential Drive(R) woofer with neo-
• Frequency Range: 57 Hz - 20 kHz (–10 dB) dymium-magnet
• Maximum Peak Output: 136 dB SPL at 1m • Bandpass Nominal
• Signal Processing: DSP based, resident in Input Module Inpedance: 2 x 2 ohms
• AC Power Operating Range: 90-132 VAC or 216-264 VAC, 50/60Hz • DC Resistance: 5.1 ohms ± 10%
• AC Input Connector: Neutrik PowerCon (NAC 3MPA) • High Frequency (3) 2408J, 38 mm (1.5 in) voice coil,
• AC Loop Through Connector: Neutrik PowerCon (NAC 3MPB) Transducer neodymium compression driver
• Audio Input Connector: XLR with loop through • Bandpass Nominal
• AC Current Requirements: 6A per system at 120V, 3A per system Inpedance: 4 ohms
at 240V • DC Resistance: 8.9 ohms ± 0.2%
• AC Line Voltage: User selectable:120V/240V (-15%,+10%)
• System Managerment: DSP based limiters for mechanical and AURAL SWEEP TEST SPECIFICATIONS:
thermal protection A. System Aural Sweep Test: 0.8V (Gain fully CCW)
• User Controls: Input Attenuator (0-16 dB), ACS Array B. L.F. Aural Sweep Test: 7V Input, 10 Hz to 1 kHz
Configuration Selector), HF level adjust- C. H.F. Aural Sweep Test: 1.0V Input, 200 Hz to 1.5 kHz
ment (+3 dB, 0 dB, –3 dB)
• DPC-2 Output as (Continuous IEC shaped pink noise into rated load PHYSICAL SPECIFICATIONS:
impedance): LF:750 Watts, HF: 125 Watts • Enclosure Dimensions: 349 x 597 x 444 mm D
• DPC-2 Output section LF: Dual-Bridged Technology(TM) ,Class D (13.75 x 23.5 x 17.5 in. D)
HF:Bridged Class D • Net Weight: 52 lb (24 kg.)
WARRANTY INFORMATION:
SYSTEM COMPONENTS:
• Refer to Warranty Statement packed with each product.
GRN/BLK YEL/BLK
LF-2
BLU
GRN YEL
Carton
364342-001
NOT USED SCHEMATIC
NOT USED
26.5” YEL/BLK
.250 SERIES,RECEPTABLE/TAB FASTON PIGGYBACK
26.5” YELLOW
.187 SERIES,RECEPTABLE/TAB FASTON PIGGYBACK
20.5”GRN/BLK
02-13
JBL VRX932LAP/230
COMPONENT EXPLODED VIEW
Wire Harness Amp Board
364338-004 443941-001
Screw (10) Input Board
804-51110-12 443920-001
10-32 x 3/4
OVAL,PH,BLK Modular PCB Bolt,Horn (2)
ZINC, LCS 444087-001 854-00000-60
1/4-20 X 3 3/4
Amplifier Trim Interface PCB HEX,CLRZINC,LCS
Enclosure Assembly 363560-001 443807-001
VRX932LAP/240 Washer, Horn Bolt (2)
(Not Available for Sale) 844-01110-07
T-Nut (10) 1/4, SAE,REG,
Corner Bracket (4) 352214-001 BLK,ZINC,LCS
364255-001 10-32 X 1/4
Screw (8) ZINC PLATED
90 DEG 352051-001 Washer (2)
(Internal cabinet) Amplifier 844-03110-06
M10 X 25MM
FLT,HEX,BLK Driver, HF 3/8 BLK
Screw (8) ZINC,LCS 2408J Split Lock
882-41110-12 (361549-003X)
6 X 3/4 Diaph Repl
PAN,PH,PB,BLK D16R2408
ZINC, LCS Drop Lever (2)
Brackets 364591-003
Blk
Screw, (2)
Gasket 354379-003
339391-001 3/16 DIA X 1 LG
12” (Shldr)
806-11010-12 ZINC,LCS
Dust Dome 1/4-20 X 3/4
71646-04 FLT,PH,UNC,
BLK ZINC,L
Pole Mount
Nut (6)
804-90003-00
T-Nut, Short Barrel
Pole Mount
JBL VRX932LAP/230
AMPLIFIER ASSEMBLY
363679-004
Amp Board
443941-001
Input Board
443920-001
Modular PCB
444087-001
Interface PCB
443807-001
FCC Label
364171-001
JBL VRX932LAP/230
JBL VRX-AF
ARRAY FRAME ASSEMBLY
Manual
353551-007
• 4” 1/4-20 bolts to horn — 5” — caution! You can break the horn at 60”/lbs,
which is prety easy with a ratchet (pull on the end of a 1’ handle with 5
pounds). 35”/lbs = 2.9 ft/lbs.
• M10 rigging screws — 40”/lbs minimum; don’t forget the threadlock! Ditto
the 1/4-20’s on the pole mount (except no threadlock)
Bumper (2)
Side Pole (2) 353696-001
361272-001
Thread Lock, Loctite
222 or Eng Equiv