Professional Documents
Culture Documents
Product Catalogue FAHU
Product Catalogue FAHU
TAH series Air Handling Units are Eurovent certified with the best performance of
certified components like AMCA certified fans, UL rated filters and UL rated flexible
Fan Coil Units are designed with low height casing and silent fans that are suitable
for standard and district cooling applications. Fan Coil units tested at UL laboratory
for performance as per AHRI 440 standards and for sound as per AHRI 350 standards.
TAH series Ecology Units are ideal kitchen ventilation product for effective filtration
and odour removal. Factory supplied control panel ensures trouble-free operation by
are also available for sustainable and efficient removal of grease and smoke from the
Condensing units and Roof-top Packaged Air Conditioners are built with
ISO 14001:2004
Environmental Management System certified by Quality Registrar Systems (QRS), UAE.
OHSAS 18001:2007
Occupational Health and Safety certified by Quality Registrar Systems (QRS), UAE.
EN 1886, EN 13053
Determining the Mechanical Characteristics, Ratings and Performance of Air Handling Units By
TUV-NORD, TUV-SUD and Intertek.
Cooler batteries can be selected with one of these
their convenience.
EN 1886 standard is a part of a series of standards for Air Handling Units used for ventilation and air
conditioning of buildings for human occupancy. It considers the mechanical performance of an Air
Handling Unit as a whole and will be supported by a standard for sections and components.
This standard specifies test methods, test requirements and classification for Air Handling Units which are
supplying and / or extracting air, via duct work for ventilating / conditioning a part or the whole of the
building. Except for the thermal and acoustic performance of the casing, the test methods and
requirements are applicable to both complete units and any separate sections.
Filter bypass test is not applicable to the testing of HEPA filters. The test method for the thermal
performance of the casing is applicable to the comparison of different constructions but not to the calculation
Similarly, the test method for the acoustic performance of the casing is applicable to the comparison of
different constructions but not to the provision of accurate acoustic data for specific units.
The ratio between the lowest temperature difference and the mean air to air temperature difference
determines the thermal bridging factor. The classification of thermal bridging factor of Air Handling Units
shall be in accordance with table given below:
Trosten WinTADS offers an incredible flexibility to the user by customizing the unit dimensions in multiples
of 10mm on the width and height meeting all aspects of customer’s requirement. The selection program
provides us with tremendous options in choosing the components and its arrangement, thereby satisfying
passage constraints.
Complete range of construction materials are available including plain galvanized steel, pre-painted
galvanized steel, aluminium and stainless steel. Trosten WinTADS covers a multitude of environments
including the most corrosive atmosphere and offers complete range of components ensures to provide the
environment with quality indoor air. Units can also be designed to suit indoor and out conditions with
with excellent rigidity. Thermal efficiencies, i.e., thermal transmittance and thermal bridging are
addressed by our unique thermal break casing design meeting the European standard EN 1886.
Aluminium profiles are offered with options of anodized finish for anti corrosion and screw less snap fixing
Polyol used for PUF insulation are blended with environment friendly CFC & HFC free agents, self
extinguishable as per ASTM D 3014 standard and the foam insulation conforms to Class “O” of ISO 1182.2
The outer skin and inner skin of the casing comes with a variety of options in choosing sheet thickness
For hygiene applications, food grade gaskets are provided as a standard feature conforming to
ducting, inlet ducting and the radiated sound levels for each octave band based on the specific working
condition and as per the tests carried out conforming to EN ISO 3744:2009 standards.
blades.
Sound performance data is derived from testing performed in accordance with AMCA standard 300. The
effects of various components, casework and unit configurations are taken into account while deriving the
been installed. All unprotected openings should be equipped with protective screen. For any service work
or inspection need to be carried out, all safety isolating switches of the unit should be tripped before the
access doors are opened and before restarting, all safety devices must be reset.
UV lamp status.
nylon caps.
Electrical heaters should be provided with separate power supply, safety thermostat and need to be
interlocked with an air flow switch. Hot water coils need to handled with utmost care while the using the
purge connections for the risk of water hammer or steam discharge. Adequate space need to be provided
in the front of the electric heater and electric control panels in accordance to the local electrical safety
regulations.
All the wheels are statically and dynamically
Fire retardant fabrics are used as flexible connectors between the fan outlet and the unit casing for
Please refer to page nos. 71 to 76 for motor ratings and cable sizing.
TROSTEN WinTADS offers wide range of application flexibility in selecting the coils using different pitches
of 12.5mm OD (1/2”) or 15.8mm OD (5/8”) copper tubes with cooling medium as water (chilled water / hot
water), glycol, steam or refrigerants of R22, R134a, R410a & R407c. Various configurations of coil
arrangements like draw-through, blow through and multi-zone are also offered.
variable air volume systems. These filters shall consist of pleated media pack enclosed in an electro
galvanized steel housing; the media shall be made of ultra fine fiber glass formed in to a series of
pleats.Corrugated Aluminum separators maintain uniform spacing between each pleat to allow
unrestricted air flow. Bar braces shall be installed on both the sides of the filter for extra reinforcement of
the media pack. H10, H11, H13 and H14 class filters are available upon request.
Canister delivery system shall consist of multiple individual canisters in metal execution. Canister shall be
assembled in a galvanized sheet metal holding frame to fit standard dimension filter sections. The
individual canister seals and holds in the frame due to its unique seal and bayonet style clamping
mechanism. Canisters shall be factory pre-filled with user specific media. Each canister shall be vibration
Heat recovery wheels are of air to air rotary heat exchangers with energy recovery over 80%, provide
improved IAQ, control humidity and save energy. By pre-conditioning the incoming fresh air, the heat
recovery wheels with minimal cross contamination, deliver fresh air at conditions close to the room
humidity ratio.
Heat Pipes
Heat pipes are energy efficient thermal superconductors with no moving parts and transfer large amounts
of heat energy across a small temperature gradient. Heat pipes with zero cross contamination are used
air coil and give up heat to the supply air coil before
returning again.
In external type steam humidifiers, the steam
maximum effectiveness by neutralizing biological and chemical contents such as mold, bacteria, viruses,
spores, allergens, VOCs and many other airborne contaminants. The UV lamps direct the UV energy onto
the evaporator coil and drain pan, destroying and preventing mold and other microbial growth.
THU-CSU
Ceiling Suspended Units Model TAH-TCS
Model THU-FMU
THU-FMU
Model THU-FMU
THU-FMU
75
76
T2
TB2
The thermal transmittance factor and thermal bridge factor shall be relaxed to T3 and TB3 respectively for
re-circulated Air Handling Units installed in conditioned plant rooms.
AHU panel insulation shall be injected polyurethane foam and be in accordance to fire retardant
Class O of ISO 1182.2 standards.
77
78
79
80
The fan motor shall meet the safety requirments of the CE and compatible with variable frequency drives.
The motor shall be mounted on a common, torsionally rigid, galvanized steel base frame.
81
82
83
0.20 0.25 0.30 0.35 0.40
SENSIBLE HEAT RATIO = Qs / Qt
50 55
1.15
45 170 0.45
1.10
85
160 1.05
80
80
150 1.00
40 0.50
15.0
0.95
140
80 55
W 0.90
75 ET 0.55
75
BU 130
35 LB 0.85
TE
M
IR
PE
0.60
YA
RA 120 0.80
TU
DR
RE
OF
75 -°
70 F 0.75
D
110 70 0.65
UN
30
°F
PO
0.70 50
R
p-
PE
0.70
em
100
U
0.65
BT
on
65
ati
Y-
70 65 0.75
P
tur
90 0.60
AL
Sa
TH
lb,
25 0.80
Bu
EN
t
0.55
14
80
We
60 0.85
65 60
.0 VO
0.90 0.50 45
DEW POINT TEMPERATURE - °F
%
70
LUME
0.95
90
ENTHALPY - BTU PER POUND OF DRY AIR
0.45
VAPOR PRESSURE - INCHES OF MERCURY
55
55 1.00
%
20
- CU.F
60
25
0%
8
60 0.40
T. PE
50
R
0%
7
50
55 0.35
50
LB. D
15 %
45 60 45 0.30
RY A
50 40
IR
40
40 5 0% %
10 15 40 0.25
45
35 %
40 30 35 0.20
Y
IDIT
SENSIBLE HEAT RATIO = Qs / Qt
40
30 HUM
13.0
5 VE 30
30% A TI 0.15
25
35 REL
8% 20
HUMIDITY RATIO - GRAINS OF MOISTURE PER POUND OF DRY AIR
30 25
20
20% 6% 20 0.10
0 15 25
10 IT Y
20 HUMID 4% 10 35
5 LATIVE 10
0 15 10% RE 0.05
-5 5 10 2% 0
0
12.0
-10 -5 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120
DRY BULB TEMPERATURE - °F
0 5 10 15 20 25 30
Ref:TR/CAT/AHU/REV03