RIVIAN
RMS-1021
Rivian Materials Standards
Steel Sheet Rev 1RMS-1021 Steel Sheet, Rev-01
01 Foreword
1a Purpose
This document establishes quirements for material performance, delivery conitions, nd quality for
steel sheet products delvere to Rvian Automotive LC, o its suppliers fr assembly into the vehicle
bls, This speciation shill never supersede appleable ws and regulations. Allmaterlls must meet
legal requirements valid inthe country of wage, Only the English language version of this text shall be
binding
1.2 Development
“This document was developed using best practices of the North American Automotive industry
02. Terms/Abbreviations/Guidance
21 Definitions
2.44 Process Accreditation ~ All materials testing must be conducted by a laboratory or facty
credited t 50 17025 by ar established third-party auditor. Equivalent accreditation may be acceptable
but requires the approval of ian Materials Engineering,
2.4.2 Standard Obsolescence ~ It is the responsibilty ofthe supplier to ensure thatthe most current
‘version ofthis and any cited standards are employed.RMS-1021 Steel Sheet, Rev-01
2.13 tnitial Source Approval ~ Delivery of production goods shall nat be accepted until representative
Init production samples hive been veri for compliance to this speiiation by Rivian Materials
Engineering
2.44 Materials Equivalency ~ Material approved and purchased to ths speciation must be
‘auivalent inal espects tothe inkl samples verified and approved by Ruan Materials Engineering. The
Fight to character materials reserved
2.15 Change Reporting ~The supplier excluevey responsible for reporting al product changes to
Rivian Materials Engineering, Materiols must be retested unless agreed otherwise
24.6 Quality Control ~ Test frequency and sample ste for process control and product continuous
compliance monitoring must neet the agreed quantiles and frequencies as definedin this document and
‘the Conte! Plan and PPAP packages
2.1.7 Drawing Precedence Incase of cnt, the requirements listed on the engineering pat drawing
‘Shall take precedenes over the terms and condtlons ofthis specification
24.8 Product Appearance All material, components and assembles deemed as “appearance items"
must match the corresponding master sample for color, gloss and texture a indeated on the applicable
feleased engineering inforration as approved by Rlvan Design Studio and in accordance withthe
Appearance Approval procedure.
2.19 IMDS Submission A materials used to produce pats under this speciation, must be registred
‘othe International Material Data Sytem prior to beng supplied for production usagRMS-1021 Steel Sheet, Rev-01
2.2. Nomenclature
The following aomencatue shal be wed to specly material rade as defined by this standard
Rolling Type-Min YS-Min UTSSteltype-SH-Coatng Surface Quality
Where
Roling Type ~ishot called (H) or codrolled (CR). For mild stels his ifllowed by aformabity number
from 1 to 5 where the higher number represent better formabilty. Direct strip casting shall adhere to
the CR regulements
[Min YS ste specified minimum veld stress ofthe grade
[Min UTS the specified minimum ultimate tensile stres ofthe grade
Steel Type i the chemistry / manufactring technology used for the steel grade.
ni Stes!
Interstitial Free Ste!
SLA High Strength Low Alo Steel
us —HSLA grades with contd sulphides
BH -Bake Hardenable Ste!
P-Dval Phase Ste!
TR-TAP Stee!
MS ~Martenste steel
SH ie toindieate that the materi sa shoot product
Coating Type it ndleate:he coating type
G1-Gavanzed
EG Electogatvanized
A. Galvannealed
{2MA~Zine Magnesium Alurinum
uc= UncoatedRMS-1021 Steel Sheet, Rev-01
‘Surface Quality =e o indicate whether the pat shall an
- Biposed Quality
U-Unexposed auaity
03. Requirements
3A Grades/Descriptions |
Table 1 Ste! Sheet Grades
Description
pen thio dows
ow enh sppetin with inpoved dma
‘Mu Senet opens
Maden tohgh sven opens
Hea sent aplisons
ed ih reg apstons
‘ein ih trong apeston
ere pesto
TEST 700CIA eh senthapeeaionRMS-1021 Steel Sheet, Rev-01
Grade Description
ae
{abo 3078 a senna wh one bbe desi
euautsaat a” tow sent apes wih moored tk ares
Med Sent opens wth npn iy
‘Meri tegatana roe ty
Tightrope wih improved coy
He tet lesions th inprve
igh tr plo wih imarved city
GhalGor BO "Wah olan th inorved tity
i S501S00¢ Meo Seren apes iden iy
~ Hie ont apieson with impreve iy
Hig rent apiesons with improve uy
Utesgnseenthsplatins
cr Urs sbeng splits
32 Dimensional Tolerances
LR steel sheet shall conforn to tolerances per ISO 16160 and CR steel sheet shall conform to the
ivensonal tolerances in tales 2,3 and 4
“Table 2; With Tolerances fr CR teat grades
—speited wath Tolerance
a =RMS-1021 Steel Sheet, Rev-01
Table 3: Length Tolerances for CR stel grades
‘Spectied Lenath Tolerance
‘Table 4 Thickness Tolerances for CR stel grades
Spectied Thebes (rn) “Tolerance (am
ae Fae
was ra
sa Fas
3.3. Chemical Composition
Compositional requirements of see, inthe as delivered stat, fr each grade shall conform tothe limits
Gefined in Table 5 {in % by mas), Measurement shall be per EN 180 14288. Addtional mits may be