Professional Documents
Culture Documents
Deh 2300
Deh 2300
Deh 2300
DEH-2300
DEH-230 X1M/UC
X1M/UC
DEH-23 X1M/UC
- This service manual should be used together with the following manual(s):
Model No. Order No. Mech. Module Remarks
CX-958 CRT2423 S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly
CONTENTS
1. SAFETY INFORMATION ............................................2 7. GENERAL INFORMATION .......................................40
2. EXPLODED VIEWS AND PARTS LIST .......................2 7.1 DIAGNOSIS ........................................................40
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .....8 7.1.1 TEST MODE ..............................................40
4. PCB CONNECTION DIAGRAM ................................24 7.1.2 DISASSEMBLY .........................................43
5. ELECTRICAL PARTS LIST ........................................32 7.1.3 CONNECTOR FUNCTION DESCRIPTION .......47
6. ADJUSTMENT..........................................................36 7.2 PARTS .................................................................48
7.2.1 IC................................................................48
7.2.2 DISPLAY ....................................................55
7.3 OPERATIONAL FLOW CHART ...........................56
8. OPERATIONS AND SPECIFICATIONS.....................57
1. SAFETY INFORMATION
CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of
California to cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
8
2
9 11
7
14 16
1
15
10
13
12
2
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
NOTE:
- Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List.
- Screws adjacent to ∇ mark on the product are used for disassembly.
Mark No. Description Part No. Mark No. Description Part No.
1 Cord Assy CDE6468 * 11-1 Warranty Card See Contrast table(2)
2 Spring CBH1650 11-2 Owner’s Manual See Contrast table(2)
3 Screw CBA1002 11-3 Installation Manual See Contrast table(2)
* 4 Polyethylene Bag CEG-127 * 11-4 Card See Contrast table(2)
5 Screw CRZ50P090FMC 12 Carton See Contrast table(2)
Part No.
Mark No. Symbol and Description DEH-2300/X1M/UC DEH-230/X1M/UC DEH-23/X1M/UC
* 11-1 Warranty Card Not used CRY1070 Not used
11-2 Owner’s Manual CRD3279 CRD3357 CRD3279
11-3 Installation Manual CRD3280 CRD3360 CRD3280
* 11-4 Card ARY1048 Not used ARY1048
12 Carton CHG4154 CHG4275 CHG4155
3
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
2.2 EXTERIOR
4
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
Part No.
Mark No. Symbol and Description DEH-2300/X1M/UC DEH-230/X1M/UC DEH-23/X1M/UC
45 Detach Grille Assy CXB6144 CXB7141 CXB6145
56 Keyboard Unit CWM7303 CWM7303 CWM7304
65 Grille Unit CXB7181 CXB7300 CXB7178
5
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
6
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
Mark No. Description Part No. Mark No. Description Part No.
1 Control Unit CWX2411 46 •••••
2 Connector(CN802) CKS2192 47 Ball CNR1189
3 Connector(CN801) CKS2193 48 Belt CNT1086
4 Connector(CN701) CKS2773 49 Roller CNV4509
5 Connector(CN101) CKS3486 50 Arm CNV6037
7
Downloaded from www.Manualslib.com manuals search engine
1 2 3 4
DEH-2300,230,23
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
A TUNER AMP UNIT
A
FM/AM TUNER UNIT
FM/AM 1ST IF 10.7MHz MPXREF 41kHz
ANTENNA CN402 AMRF T51 Q51 CF51 CF52 CF53 AMDET
AMANT
28 ATT L ch
IC 2 FM MPX 6
R ch
5
IC 3
IMG ADJ AM 2ND IF X901 EEPROM
450kHz 10.25MHz
FMLOCL
VDD
STIND
SDBW
DGND
FMSD
DI/DO
CREQ
VCC
RF ADJ
NL1
NL2
CE2
CE1
WC
NC
NC
NC
CK
SL
LOCH LOCL
23 25 7 17 20 22 10 19 14 24 9 11 12 15 16 8 13 2 3 4 1
Q411
PDIO
PCE2
PCK
PCE1
SL
SD
PDIO
LOCL
VCC VDD
18 TOP HOME
4
SPINDLE M S801
C MOTOR 12
SOP
HOME
11
CN801 SOM
14
1 COP
CARRIAGE M 13 COM 1 CDLOAD CDLOAD
MOTOR 2 FWD 6 19
10 28 CDEJET EJET
LOP REV 5 20
9 21 CONT CONT
LOM MUTE 11 14
LOADING 3
MOTOR
M
4
CN802
EJTSNS EJTD
3 22 3
1 DSCSNS DINC
23 2
CLAMP CLAMP
VD 21 4
SELECT Q981
SENSE D802 D801 VD
S802 VD 24 1 B.U
2 CLAMP
DISC SENSE +5V REGULATOR
4 IC 701 2
D PHOTO UNIT(S8) VDD
BA05SFP
IN
Q982
1 CD5VON CD5VON
7 18
VDCONT
8
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-2300,230,23
CN301
REAR L CH
Q346
SYSTEM
CONTROLLER
IC 601(1/2)
PE5196A
6
SD
76
SL
14
PCE
13
PCK
48
TUNPCE2
12
PDO
PDIO 11
PDI VST
VCK Q363
57 VDT
LOCL
CN901
Q903
BACKUP
VDD B.U B.U
FUSE
10A B
2
BACK UP
GND
1
VST/ VCK/ VDT GND
2 POWER AMP
IN2_L
E.VOL 23 FL—
9
FL–
FIE/EQ 10 14 21 FL+
3 Frontout_L FL IC 302 11
IN3_L FL+
11 12 RL PAL006A 3 RL—
IC 301 Rearout_L 10
RL–
PML003AM 5 RL+
12
RL+
MUTE STBY B.REM
22 4 25
SYSPW
SYSTEM
CONTROLLER
IC 601(2/2) C
PE5196A
42
SYSPW B.REM
31 CDLOAD 5
34 CDEJET B.REM
23 CONT
44
80 MUTE
EJTSNS
79
DSCSNS
B KEYBOARD UNIT
27
CLAMP
CN601 CN1801
8 20
KYDT 3 3 KYDT
22 9 LCD
VDCONT 4 4 18
DPDT DPDT
RESET
60 1 IC 602 2
RESET VDD
S—80834ANY
VDD
56
5 5 VDD
10 VLCD
41
SWVDD Q650
35
CD5VON
KEY CONT.
LCD DRIVER
D
IC 1801
KEY MATRIX PD6340A
22 23
X1801
9
Downloaded from www.Manualslib.com 5manuals search engine 6 7 8
1 2 3 4
DEH-2300,230,23
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)
Note: When ordering service parts, be sure to refer to “EXPLODED VIEWS AND PARTS LIST” or “ELECTRICAL PARTS
LIST”.
A
A TUNER AMP UNIT
A-a
Large size
SCH diagram
A-a A-b
FM/AM TUNER UNIT
FM(100%):-19.5dBs
CN402
AM(30%):-30dBs
A-a A-b Guide page
183
DSP-201M-S00B
162
162
183
CN403
272
822
473
PE5196A
SYSTEM CONTROLLER
CN601
B
KEYBOARD
UNIT
D
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and For resistors and capacitors in the circuit diagrams, their resistance values or
discrete resistors. capacitance values are expressed in codes:
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and Ex. *Resistors
discrete capacitors. Code Practical value
The > mark found on some component parts indicates 123 12k ohms
the importance of the safety factor of the part. 103 10k ohms
Therefore, when replacing, be sure to use parts of
identical designation. *Capacitors
Code Practical value
A
103 0.01µF
101/10 100µF/10V
10
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-2300,230,23
A-b A
FM(100%):+3.6dBs
AM(30%):-6.9dBs
CD:+9.4dBs
CD:+10.2dBs
E.VOL
FIE/EQ
CN301
B.REM
332/16
CN901
POWER AMP
PAL006A
FM(100%):+29.6dBs
AM(30%):+19.1dBs
CD:+36.2dBs
>
CEK1136
600µH
331/16
RESET
A.SENS
B.SENS
CN605
CONTROL UNIT
CD:+4.1dBs
D
C
1
A-a A-b
FM(100%):-19.5dBs
AM(30%):-30dBs
162 162
272
272
183 183
B
FM/AM TUNER UNIT
C
TUNER AMP UNIT
A
D
DSP-201M-S00B
CN402
CN403
12
1
A-a
Downloaded from www.Manualslib.com manuals search engine
2 3 4
RESE
5
822
473
2
SYSTEM CONTROLLER
6
6
CN601
B
KEYBOARD
UNIT
7
7
NOTE :
CONTROL UNIT
8
*Capacitors
8
A-a
Code Practical value
103 0.01µF
101/10 100µF/10V
13
DEH-2300,230,23
A-a A-b
B
C
A
D
B
D
A
14
A-a A-b
1
1
A-b
FM(100%):+3.6dBs
E.VOL
FIE/EQ
CN301
B.REM
3
3
CN901
332/16
POWER AMP
PAL006A
4
4
FM(100%):+29.6dBs
AM(30%):+19.1dBs
CD:+36.2dBs
>
CEK1136
600µH
5 6 7 8
DEH-2300,230,23
A-a A-b
CEK1136
A
600µH
331/16
C
CD:+4.1dBs
A.SENS
B.SENS
CN605
D
RESET
CONTROL UNIT C
A-b 15
2
B KEYBOARD UNIT
LCD DRIVER
KEY CONTROLLER
LCD CAW1606
16 B
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-2300,230,23
EQ
A
IL1801, 1802:CEL1638(14V 40mA) CN601
(DEH-23/X1M/UC)
IL1801, 1802:CEL1651(14V 40mA)
(DEH-2300/X1M/UC) B
CLK LOUD
(DEH-230/X1M/UC)
R1708, 1710, 1712:181
BSM
(DEH-23/X1M/UC)
C
D1701-1708:SML210DT
D1701-1708:SML210PT
(DEH-2300/X1M/UC)
(DEH-230/X1M/UC)
(DEH-23/X1M/UC)
A
C CONTROL UNIT
PICKUP UNIT
(SERVICE)(P8)
CN101
RF-AMP, SE
CL203IRXTU CL203IRXTU
D PHOTO UNIT(S8)
Q1 CPT230SX-TU Q2 CPT230SX-TU
CN802
SPINDLE MOTOR
M3 CXB2562
CARRIAGE MOTOR
M1 CXB2190
D LOADING MOTOR
CD DRIVER
M2 CXB2195
CN801
18 C D
Downloaded from www.Manualslib.com
1 manuals search engine
2
BA05SFP
5V REGULATOR
3 4
5 6 7 8
DEH-2300,230,23
SWITCHES:
CONTROL UNIT
S801 : HOME SWITCH.....ON-OFF
S802 : CLAMP SWITCH....ON-OFF
The underlined indicates the switch position.
CN701
CN605
A
Note:1. The encircled numbers denote measuring pointes in the circuit diagram.
2. Reference voltage
REFO:2.5V
- Waveforms
1 RFI 0.5V/div. 0.5µs/div. 1 CH1: RFI 1V/div. 0.5ms/div. 1 CH1: RFI 1V/div. 0.5ms/div.
Normal mode: play 2 CH2: MIRR 5V/div. 2 CH2: MIRR 5V/div.
Test mode: Tracking open Normal mode: The defect part
passes 800µm
REFO →
REFO →
REFO →
REFO →
REFO →
REFO → REFO →
REFO →
REFO →
REFO → REFO →
GND →
REFO → REFO →
REFO →
20
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
REFO →
REFO →
REFO →
REFO → REFO →
REFO →
REFO →
REFO →
REFO →
GND →
REFO →
REFO → REFO →
REFO →
GND → GND →
GND →
REFO → REFO →
GND → GND →
21
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
REFO →
REFO → REFO →
22
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
23
Downloaded from www.Manualslib.com manuals search engine
1 2 3 4
DEH-2300,230,23
CORD ASSY
Connector Capacitor
SIDE A
B
C B
24 A
Downloaded from www.Manualslib.com
1 manuals search engine
2
CN701
3 4
CN1801
5 6 7 8
DEH-2300,230,23
SIDE A
3
1 2
C
FM/AM TUNER UNIT
FRONT
A
A TUNER AMP UNIT
4 3
5 2
6 1
1 6
2 5
3 4
26 A
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-2300,230,23
SIDE B
4 3
1 6 5 2
2 5 6 1
3 4
FRONT
EJECT
A
→
↑
↓
BSM
6 CLK
B
54
3 2
C
1
SOURCE
SOURCE
KEYBOARD UNIT
VOL-
VOL+
VOL+
VOL-
LOUD
D
EQ
B
28 B
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
1 2 3 4
DEH-2300,230,23
SIDE B
A
B
CN601
C
A
KEYBOARD UNIT
D
B
D
A
30
C CONTROL UNIT
1
1
PICKUP UNIT(SERVICE)(P8)
M1 CARRIAGE MOTOR
HOME
M3 SPINDLE MOTOR
3
3
4
4
3
2 C CN802
1
SIDE A
1 2 3 4
DEH-2300,230,23
SIDE B
CLAMP
B
CONTROL UNIT
C
C
32
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
--- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ -------------------------
R 629 RS1/16S473J C 366 CKSQYB474K16
R 630 RS1/16S822J C 367 CKSQYB474K16
R 631 RD1/4PU102J C 368 CKSQYB474K16
R 649 RS1/16S222J C 369 CKSQYB474K16
R 650 RD1/4PU222J C 370 CKSQYB474K16
33
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
--- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ -------------------------
RESISTORS R 1803 RS1/16S471J
R 1804 RS1/16S471J
R 1701 RS1/16S151J R 1805 RS1/16S471J
R 1702 RS1/16S181J R 1806 RS1/16S471J
R 1703 RS1/16S181J
R 1704 RS1/16S181J CAPACITORS
R 1705 RS1/16S181J
C 1801 CKSRYB103K50
R 1706 RS1/16S151J C 1811 CKSQYF104Z25
R 1707 RS1/16S151J C 1812 CKSQYF104Z25
R 1708 RS1/16S151J
Unit Number : CWX2411
R
R
1709
1710
RS1/16S181J
RS1/16S151J C Unit Name : Control Unit
R 1711 RS1/16S181J
R 1712 RS1/16S151J
MISCELLANEOUS
R 1713 RS1/16S131J
IC 201 IC UPD63711GC
R 1801 RS1/16S222J
IC 301 IC BA5985FM
R 1802 RS1/16S222J
IC 701 IC BA05SFP
Q 101 Transistor 2SB1132
R 1803 RS1/16S471J
D 801 LED CL203IRXTU
R 1804 RS1/16S471J
R 1805 RS1/16S471J
D 802 LED CL203IRXTU
R 1806 RS1/16S471J
X 201 Ceramic Oscillator 16.934MHz CSS1456
S 801 Spring Switch(HOME) CSN1051
CAPACITORS S 802 Spring Switch(CLAMP) CSN1052
C 1801 CKSRYB103K50
C 1811 CKSQYF104Z25
RESISTORS
C 1812 CKSQYF104Z25
R 101 RS1/8S120J
R 102 RS1/8S100J
Unit Number : CWM7304(DEH-23/X1M/UC)
B Unit Name : Keyboard Unit
R
R
R
103
201
202
RS1/16S222J
RS1/16S104J
RS1/16S103J
MISCELLANEOUS
R 203 RS1/16S393J
IC 1801 IC PD6340A R 204 RS1/16S103J
D 1701 LED SML210DT R 205 RS1/16S103J
D 1702 LED SML210DT R 206 RS1/16S182J
D 1703 LED SML210DT R 207 RS1/16S123J
D 1704 LED SML210DT
R 302 RS1/16S153J
D 1705 LED SML210DT R 303 RS1/16S103J
D 1706 LED SML210DT R 501 RS1/16S102J
D 1707 LED SML210DT R 502 RA4C681J
D 1708 LED SML210DT R 601 RS1/16S102J
D 1801 Diode MA152WK
R 602 RS1/16S102J
D 1802 Diode MA152WA R 605 RS1/16S0R0J
D 1811 LED NSSW440-9159 R 606 RS1/16S0R0J
D 1812 LED NSSW440-9159 R 801 RS1/8S751J
X 1801 Ceramic Resonator 4.97MHz CSS1422 R 803 RS1/8S751J
IL 1801 Lamp 14V 40mA CEL1638
R 902 RS1/16S0R0J
IL 1802 Lamp 14V 40mA CEL1638 R 906 RS1/16S0R0J
LCD CAW1606
CAPACITORS
RESISTORS
C 101 CKSRYB102K50
R 1701 RS1/16S151J C 102 CKSRYB104K16
R 1702 RS1/16S181J C 103 CEV101M6R3
R 1703 RS1/16S181J C 104 CEV470M6R3
R 1704 RS1/16S181J C 105 CKSQYB334K16
R 1705 RS1/16S181J
C 106 CKSQYB334K16
R 1706 RS1/16S151J C 107 CKSQYB334K16
R 1707 RS1/16S151J C 201 CKSRYB104K16
R 1708 RS1/16S181J C 202 CKSRYB471K50
R 1709 RS1/16S181J C 203 CKSRYB104K16
R 1710 RS1/16S181J
C 205 CEV101M6R3
R 1711 RS1/16S181J C 206 CKSRYB104K16
R 1712 RS1/16S181J C 207 CKSRYB104K16
R 1713 RS1/16S131J C 208 CKSRYB104K16
R 1801 RS1/16S222J C 209 CKSRYB104K16
R 1802 RS1/16S222J
34
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
C 215 CKSRYB104K16
C 216 CCSRCJ3R0C50
C 217 CCSRCH270J50
C 218 CKSRYB104K16
C 219 CCSRCH181J50
C 220 CCSRCH510J50
C 221 CKSRYB682K25
C 222 CEV220M6R3
C 223 CKSRYB103K25
C 224 CKSRYB224K10
C 301 CEV101M10
C 603 CCSQSL152J50
C 604 CCSQSL152J50
C 702 10µF/10V CCH1349
C 703 CKSQYB334K16
Unit Number :
D Unit Name : Photo Unit(S8)
Q 1 Photo-transistor CPT230SX-TU
Q 2 Photo-transistor CPT230SX-TU
35
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
6. ADJUSTMENT
6.1 CD ADJUSTMENT
1) Precautions 2) Test Mode
• This unit uses a single power supply (+5V) for the reg- This mode is used for adjusting the CD mechanism
ulator. The signal reference potential, therefore, is module of the device.
connected to REFO(approx. 2.5V) instead of GND.
If REFO and GND are connected to each other by mis- • Test mode starting procedure
take during adjustments, not only will it be impossi- Reset while pressing the 4 and 6 keys together.
ble to measure the potential correctly, but the servo
will malfunction and a severe shock will be applied to • Test mode cancellation
the pick-up. To avoid this, take special note of the fol- Switch ACC, back-up OFF.
lowing.
Do not connect the negative probe of the measuring • After pressing the EJECT key, do not press any other
equipment to REFO and GND together. It is especially key until the disk is completely ejected.
important not to connect the channel 1 negative
probe of the oscilloscope to REFO with the channel 2 • If the ] or [ key is pressed while focus search is in
negative probe connected to GND. progress, immediately turn the power off (otherwise
Since the frame of the measuring instrument is usual- the actuator may be damaged due to adhesion of the
ly at the same potential as the negative probe, change lenses).
the frame of the measuring instrument to floating sta-
tus. • Jump operation of TRs other than 100TR continues
If by accident REFO comes in contact with GND, after releasing the key. CRG move and 100TR jump
immediately switch the regulator or power OFF. operations are brought into the “Tracking close” sta-
tus when the key is released.
• Always make sure the regulator is OFF when connect-
ing and disconnecting the various filters and wiring • Powering Off/On resets the jump mode to “1TR”, and
required for measurements. the automatic adjustment value to the initial value.
36
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
- Flow Chart
4 6
Test Mode In
Reset
Select CD SOURCE
BAND 3 6
Power ON
(Adjustment for T.Offset)
Power ON
TRK MIN SEC
(Not adjustment for T.Offset)
Display 00 00 00 TRK MIN SEC
Display 99 99 99
Power OFF
BAND 3 6 1 ] [ 2
Display
91 91 91 Display 0x 0x 0x 00 00 00 00 00 00 00 00 00
or or or
TRK MIN SEC TRK MIN SEC TRK MIN SEC
99 99 99 99 99 99 99 99 99
Power OFF
BAND 1 6 3 ] [ 2
T.Close and
F,T AGC and T. Close and RF AGC Coefficient Display/ CRG+ CRG- T.Balance
RF AGC and Fit Servo Rough Servo and RF AGC Adjustment
Fit Servo TRK MIN SEC TRK MIN SEC
Display 8x 8x 8x 8x 8x 8x
or or
TRK MIN SEC TRK MIN SEC
9x 9x 9x 9x 9x 9x
Tracking
Power OFF Open
BAND 1 3 6 ] [ 2
*4 *5 *6 CRG-/TR Jump- *6
F, T, RF AGC/ F, T AGC and CRG/TR Jump NO. CRG+/TR Jump+ *7
F.Bias Display Select RF AGC Select TRK MIN SEC
Power OFF
Display
8x 8x 8x
or
BAND TRK MIN SEC
2
9x 9x 9x
Tracking
Open
TRK MIN SEC
Display 8x 8x 8x
or
TRK MIN SEC
9x 9x 9x
37
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
• Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFOUT
• Disc • ABEX TCD-784
• Mode • TEST MODE
CONTROL UNIT
E
F L.P.F.
Xch Ych
E 100kΩ
Oscilloscope
REFO 390pF
F 100kΩ
390pF
REFO REFO
L.P.F.
• Checking Procedure
1. In test mode, load the disc and switch the 5V regulator on.
2. Using the ] and [ buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjust-
ment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase differ-
ence is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver-
age angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
38
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
0° 30°
45° 60°
75° 90°
39
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 TEST MODE
- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the
error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the
users and also for facilitating trouble analysis and repair work in servicing.
40
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
41
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
42
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
7.1.2 DISASSEMBLY
- Removing the Case Unit (not shown)
1. Remove the Case Unit.
Fig.1
CD Mechanism Module
Cover
- Removing the Tuner Amp Unit
Fig.2
Remove the screw. (Fig.3)
Fig.3
Tuner Amp Unit
43
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
B A
Arm A
Arm
B A
44
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
A A
45
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
A
A
Loading Motor
Pickup Unit
Shaft
46
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
15 13 11 9 7 5 3 1
16 14 12 10 8 6 4 2
1. BACK UP
2. GND
3. NC
4. ACC
5. B.REM
6. NC
7. NC
8. NC
9. FL-
10. RL-
11. FL+
12. RL+
13. FR-
14. RR-
15. FR+
16. RR+
47
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
7.2 PARTS
7.2.1 IC
- Pin Functions(PE5196A)
Pin No. Pin Name I/O Format Function and Operation
1 MODEL1 I Model select input
2 NL1 I Noise level input
3 NL2DT I Noise level input 2
4 AVSS AVSS
5 ST I Stereo input
6 SD I SD signal input
7 AREF1 AVREF1
8 KYDT I Key data input
9 DPDT O C Key data output
10 SDBW I SDBW input
11 TUNPDI I PLL IC data input
12 TUNPDO O C PLL IC data output
13 TUNPCK O C PLL IC clock output
14 TUNPCE O C PLL IC chip enable output
15 currq O C Tuner voltage FIX output
16 XSI I C CD LSI serial data input(TSI)
17 XSO O C CD LSI serial data output(TSO)
18 XSCK O C CD LSI serial clock output(TSCK)
19 drst O C RDS decoder reset output
20 ADPW O C A/D converter power output
21 fm/AM O C Tuner power supply control output
22 VDCONT O C VD power supply control output
23 CONT O C Servo driver power control output
24 XAO O C CD LSI command / data control output
25 xrst O C CD LSI reset control output
26 xstb O C CD LSI strobe output
27 CLAMP I Disc clamp sense input
28 MIRR I Mirror detection input
29 FOK I Focus OK signal input
30 LOCK I Spindle lock detector input
31 CDLOAD O LOAD motor loading control output
32 TELIN I Cellular mute input
33 VSS VSS
34 CDEJECT O LOAD motor eject control output
35 CD5VON O C CD +5V power supply control output
36–39 NC Not used
40 RECIEVE O C RDS decoder receiving output
41 swvdd O C Grille microcomputer power supply control output
42 SYSPW O C System power supply control output
43 ILMPW O C Illumination power output
44 mute O C Mute output
45 PEE O C Beep tone output
46 LOCH O C LOCH output
47 RDS57K I 57kHzBP-OUT sense input
48 TUNPCE2 O C EEPROM chip enable output
49 PCL O C Test mode clock adjustment output
50 VCK O C Clock output for electronic volume
51 VDT O C Data output for electronic volume
52 ANTPW O Antenna power output
53 VST O Strobe pulse output for electronic volume
54 DALMON O Stand-by output
55,56 NC Not used
57 LOCL O LOCL output
58 rdslk I RDSLK input
48
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
80 61
1 60
S-80834ANY
20 41
21 40
1 2 3
OUT VDD VSS
49
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
*PD6340A
33
48
32 49
17 64
16
50
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
51
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
1
1
26
21 100
80
50
40 76
61
51
75
41
60
52
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
PAL006A
sw_vcc
Protector;
Over voltage
1
TAB Reference
amp_vcc
2 Stand-by
P-GND2 Circuit
+-
3
OUT2-
1CM
Offset Protector;
4
-+
5
OUT2+
6
VCC
+-
7
OUT1-
1CM
Offset
8
P-GND1 Detection
-+
9
OUT1+
10
SVR
11
IN1
12 13
IN2
Protector; amp_vcc
S-GND Short circuit
14
IN4
15
IN3
16
AC-GND
17
+-
OUT3+
1CM
18
Offset
P-GND3 Detection
19
-+
OUT3-
20 21
VCC
+-
OUT4+
1CM
22
Offset
MUTE Detection
23
-+
OUT4-
24 25
P-GND4
SWITCH
sw_vcc
stby
Protector;
Over current limit
Mute circuit
53
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
IC 3
IMG ADJ AM 2ND IF X901 EEPROM
450kHz 10.25MHz
FMLOCL
VDD
STIND
SDBW
DGND
FMSD
DI/DO
CREQ
VCC
RF ADJ
NL1
NL2
CE2
CE1
WC
NC
NC
NC
CK
SL
LOCH LOCL
23 25 7 17 20 22 10 19 14 24 9 11 12 15 16 8 13 2 3 4 1
54
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
55
COM3A COM3A 50
COM2A COM2A 49
COM1A COM1A 48
COM2B COM2B
47
COM0A COM0A 46
COM2C COM2C
COMMON
45
SEGMENT
COM3B COM3B 44
COM2D COM2D 43
COM1B COM1B 42
COM0B COM0B 41
SEG39 40
SEG38 39
SEG37 38
SEG35 37
SEG34 36
SEG33 35
SEG32
34
SEG31 33
SEG30 32
SEG29
31
SEG28 30
SEG27 29
SEG26
28
SEG25
27
SEG24
26
SEG23
25
SEG22
24
SEG21 23
SEG20 22
SEG19 21
SEG18
20
SEG17
19
SEG16
18
SEG15 17
SEG14
16
SEG13 15
SEG12 14
SEG11 13
SEG10 12
SEG9 11
SEG8 10
SEG7 9
SEG6 8
SEG5 7
SEG4 6
SEG3
5
SEG2
4
NC
3
NC 2
SEG36 1
- CAW1606
7.2.2 DISPLAY
DEH-2300,230,23
DEH-2300,230,23
Power ON
VDD=5V
68pin
bsens
64pin
BSENS=L
asens
63pin
ASENS=L
dsens
65pin
DSENS=L
ADPW←H
20pin
SWVDD←L
41pin
300ms
In case of the above signal, the communication
Source keys with Grille microcomputer may fail.
operative If the time interval is not 300msec, the oscillator
may be defective.
Source ON
SYSPW←H
42pin
56
Downloaded from www.Manualslib.com manuals search engine
DEH-2300,230,23
Key Finder
Head Unit
AUDIO button
BAND button
57
Downloaded from www.Manualslib.com manuals search engine
Basic Operation
58
To Listen to Music Basic Operation of Tuner
The following explains the initial operations required before you can listen to music.
Note:
• Loading a disc in this product. Manual and Seek Tuning
1. Select the desired source (e.g. Tuner). • You can select the tuning method by changing the length of time you
press the 2/3 button.
DEH-2300,230,23
Note:
• Up to 18 FM stations (6 in FM1, FM2 and FM3) and 6 AM stations
can be stored in memory.
• You can also use the 5 or ∞ buttons to recall broadcast stations
memorized in buttons 1 through 6.
Basic Operation
Eject
Note:
CD Loading Slot • The CD function can be turned ON/OFF
with the disc remaining in this product.
Note: • A disc left partially inserted after ejection
• The built-in CD player plays one standard 12 cm may incur damage or fall out.
or 8 cm (single) CD at a time. Do not use an
Note:
• If a disc cannot be inserted fully or playback fails, make sure the recorded side is down.
Push the EJECT button and check the disc for damage before reinserting it.
• If a disc is inserted with the recorded side up, it will be ejected automatically after a few
moments.
• If the built-in CD player cannot operate properly, an error message (such as “ERR-14”)
appears on the display. Refer to “Built-in CD Player’s Error Message”.
59
DEH-2300,230,23
Connection Diagram
60
This product
Power amp
Rear output
(sold separately)
DEH-2300,230,23
Connecting cords
with RCA pin plugs
(sold separately).
Antenna jack Fuse
8.2 SPECIFICATIONS
General CD player
Power source .......... 14.4 V DC (10.8 – 15.1 V allowable) System .................................... Compact disc audio system
Grounding system ........................................ Negative type Usable discs .................................................. Compact disc
Max. current consumption ...................................... 10.0 A Signal format .................... Sampling frequency: 44.1 kHz
Dimensions Number of quantization bits: 16; linear
(DIN) (chassis) ...... 178 (W) × 50 (H) × 159 (D) mm Frequency characteristics .............. 5 – 20,000 Hz (±1 dB)
[7 (W) × 2 (H) × 6-1/4 (D) in] Signal-to-noise ratio ...... 94 dB (1 kHz) (IHF-A network)
(nose) ............ 188 (W) × 58 (H) × 19 (D) mm Dynamic range ............................................ 92 dB (1 kHz)
[7-3/8 (W) × 2-1/4 (H) × 3/4 (D) in] Number of channels ............................................ 2 (stereo)
(D) (chassis) ...... 178 (W) × 50 (H) × 164 (D) mm
[7 (W) × 2 (H) × 6-1/2 (D) in] FM tuner
(nose) ............ 170 (W) × 48 (H) × 14 (D) mm Frequency range .................................... 87.9 – 107.9 MHz
[6-3/4 (W) × 1-7/8 (H) × 1/2 (D) in] Usable sensitivity ...................................................... 9 dBf
(0.8 µV/75 Ω, mono, S/N: 30 dB)
Weight ........................................................ 1.4 kg (3.1 lbs) 50 dB quieting sensitivity .... 15 dBf (1.5 µV/75 Ω, mono)
Electrode dark current .................................... 6mA or less Signal-to-noise ratio ...................... 70 dB (IHF-A network)
Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo)
Amplifier Frequency response ...................... 30 – 15,000 Hz (±3 dB)
Continuous power output is 22 W per channel min. into 4 Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)
ohms, both channels driven 50 to 15,000 Hz with no more Selectivity .................................................................. 70 dB
than 5% THD. Three-signal intermodulation
Maximum power output ...................................... 50 W × 4 (desired signal level) ........................................ 30 dBf
Load impedance .......................... 4 Ω (4 – 8 Ω allowable) (two undesired signal level: 100 dBf)
Preout maximum output
level/output impedance ............................ 2.2 V/1 kΩ AM tuner
Equalizer (3-Band Equalizer) Frequency range ...................... 530 – 1,710 kHz (10 kHz)
(Low) .................................................. Level: ±12 dB Usable sensitivity .............................. 18 µV (S/N: 20 dB)
(Mid) .................................................... Level: ±12 dB Selectivity ................................................ 50 dB (±10 kHz)
(High) .................................................. Level: ±12 dB
Loudness contour
(Low) .................. +3.5 dB (100 Hz), +3 dB (10 kHz)
(Mid) ................ +10 dB (100 Hz), +6.5 dB (10 kHz)
(High) ................ +11 dB (100 Hz), +11 dB (10 kHz)
(volume: –30 dB)
Note:
• Specifications and the design are subject to possi-
ble modification without notice due to improve-
ments.
61
Downloaded from www.Manualslib.com manuals search engine