Professional Documents
Culture Documents
Driver Information System: Section
Driver Information System: Section
E
CONTENTS
PRECAUTION ............................................................ 3 Vehicle Speed Signal Inspection ............................ 23 F
Precautions for Supplemental Restraint System Engine Oil Pressure Signal Inspection ................... 23
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN- Water Temperature Signal Inspection .................... 25
SIONER” .................................................................. 3 Engine Speed Signal Inspection ............................. 25 G
Wiring Diagrams and Trouble Diagnosis .................. 3 Fuel Level Sensor Unit Inspection .......................... 26
PREPARATION ........................................................... 4 FUEL LEVEL SENSOR UNIT ............................. 26
Commercial Service Tool ......................................... 4 LOW-FUEL WARNING LAMP ............................. 26
H
COMBINATION METERS ........................................... 5 Fuel Gauge Fluctuates, Indicates Wrong Value, or
System Description .................................................. 5 Varies ...................................................................... 27
UNIFIED METER CONTROL UNIT ...................... 5 Fuel Gauge Does Not Move to Full-position ........... 28
POWER SUPPLY AND GROUND CIRCUIT ........ 6 DTC [U1000] CAN Communication Circuit ............. 28 I
WATER TEMPERATURE GAUGE ........................ 6 DTC [B2205] Vehicle Speed Circuit ........................ 28
ENGINE OIL PRESSURE GAUGE ....................... 6 Electrical Components Inspection .......................... 29
VOLTAGE GAUGE ................................................ 6 FUEL LEVEL SENSOR UNIT CHECK ................ 29 J
TACHOMETER ..................................................... 6 Removal and Installation of Combination Meter ..... 29
FUEL GAUGE ....................................................... 6 COMPASS AND THERMOMETER ........................... 30
SPEEDOMETER ................................................... 6 System Description ................................................. 30
DI
CAN COMMUNICATION SYSTEM DESCRIP- OUTSIDE TEMPERATURE DISPLAY ................. 30
TION ...................................................................... 6 DIRECTION DISPLAY ......................................... 30
Component Parts and Harness Connector Location..... 7 Wiring Diagram — COMPAS — ............................. 31
Combination Meter ................................................... 8 Trouble Diagnoses ................................................. 32 L
CHECK .................................................................. 8 PRELIMINARY CHECK FOR THERMOMETER... 32
Circuit Diagram ........................................................ 9 INSPECTION/COMPASS AND THERMOME-
Wiring Diagram — METER — ................................ 10 TER ..................................................................... 32 M
Terminals and Reference Value for Combination Calibration Procedure for Compass ....................... 33
Meter ...................................................................... 12 CORRECTION FUNCTIONS OF COMPASS ...... 33
Meter/Gauge Operation and Odo/Trip Meter ......... 13 INITIAL CORRECTION PROCEDURE FOR
SELF-DIAGNOSIS FUNCTION .......................... 13 COMPASS ........................................................... 33
HOW TO INITIATE COMBINATION METER WARNING LAMPS .................................................... 34
SELF-DIAGNOSIS MODE .................................. 13 Schematic ............................................................... 34
COMBINATION METER SELF-DIAGNOSIS Wiring Diagram — WARN — .................................. 35
MODE FUNCTIONS ........................................... 13 Oil Pressure Warning Lamp Stays Off (Ignition
CONSULT-II Function (METER) ............................. 17 Switch ON) ............................................................. 44
CONSULT-II BASIC OPERATION ....................... 17 Oil Pressure Warning Lamp Does Not Turn Off (Oil
SELF-DIAGNOSTIC RESULTS .......................... 18 Pressure Is Normal) ................................................ 47
DATA MONITOR ................................................. 18 Component Inspection (QR25DE Models) ............. 47
How to Proceed With Trouble Diagnosis ................ 21 OIL PRESSURE SWITCH ................................... 47
Diagnosis Flow ....................................................... 21 A/T INDICATOR ........................................................ 48
Power Supply and Ground Circuit Inspection ........ 22 Wiring Diagram — AT/IND — ................................. 48
Symptom Chart ...................................................... 23 A/T Indicator Does Not Illuminate ........................... 49
PRECAUTION PFP:00011
A
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER” EKS00BSD
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along B
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING: D
● To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer. E
● Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section. F
● Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
G
Wiring Diagrams and Trouble Diagnosis EKS00BSE
DI
PREPARATION PFP:00002
PBIC0191E
DI
WKIA3997E I
DI
CHECK
LKIA0580E
DI
WKWA2827E
WKWA2828E
DI
WKWA2114E
Condition
Terminal Wire Reference value (V)
Item Ignition
No. color Operation or condition (Approx.)
switch
3 R/Y Battery power supply OFF — Battery voltage
4 B/Y Fuel level sensor ground ON — 0V
Oil pressure sensor refer-
8 GR ON — 5V
ence voltage
Refer to DI-26, "Fuel Level Sensor
9 BR Fuel level sensor signal — —
Unit Inspection" .
Oil pressure sensor
10 B ON — 0V
ground
11 P CAN-L — — —
12 L CAN-H — — —
13 GR Ground — — 0V
Ignition switch ON or
16 W/G ON — Battery voltage
START
Oil pressure sensor sig-
19 W ON — 0 - 5V
nal
Refer to LT-159, "ILLUMINATION
22 BR Illumination control switch — Lighting switch ON OPERATION BY LIGHTING
SWITCH" .
23 B Ground — — 0V
SELF-DIAGNOSIS FUNCTION A
The following items can be checked during Combination Meter Self-Diagnosis Mode.
● Gauge sweep and present gauge values.
B
● Illuminates all odometer/trip meters and A/T indicator segments.
● Illuminates all micro controlled lamps/LEDs regardless of switch position.
● Displays estimated present battery voltage.
C
● Displays seat belt buckle switch LH status.
HOW TO INITIATE COMBINATION METER SELF-DIAGNOSIS MODE
NOTE: D
Once entered, Combination Meter Self-Diagnosis Mode will function with the ignition switch in ON or START.
Combination Meter Self-Diagnosis Mode will exit upon turning the ignition switch to OFF or ACC.
To initiate Combination Meter Self-Diagnosis Mode, refer to the following procedure. E
1. Turn the ignition switch ON, while holding the odometer/trip meter switch for 5 - 8 seconds.
NOTE:
If the diagnosis function is activated the odometer/trip meter will display tESt. F
COMBINATION METER SELF-DIAGNOSIS MODE FUNCTIONS
To interpret Combination Meter Self-Diagnosis Mode functions, refer to the following table.
G
Event Odometer Display Description of Test/Data Notes:
Odometer/trip meter A/B
switch held from 5 to 8 H
tESt Initiating self-diagnosis mode
seconds (or until
released)
Performs sweep of all
gauges, then displays I
Gauges sweep within 10 sec-
Next test requested GAGE present gauge values.
onds
Performs checksum tests
on ROM and EE. J
Lights all odometer/trip Initiating self-diagnosis mode
Next test requested (All segments illuminated)
meter segments. complete
Illuminates all micro-con- DI
trolled lamps/LEDs
Next test requested bulb
regardless of SW configu-
ration.
L
Return to normal opera-
tion of all lamps/LEDs and
Odometer/trip meter A/B
displays hex ROM rev. If
switch engaged and
rXXXX, FAIL a ROM checksum fault M
released = next test
exists, display alternates
requested
between "r XXXX" and
"FAIL".
Displays hex ROM rev as
Next test requested nrXXXX
stored in NVM.
Hex EE level. If EE
checksum fault exists,
Next test requested EE XX, FAIL display alternates
between "EE XX" and
"FAIL".
Hex coding of final manu-
Next test requested dtXXXX
facturing test date.
A
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
METER diagnosis mode Description
SELF-DIAG RESULTS Displays combination meter self-diagnosis results. B
DATA MONITOR Displays combination meter input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
C
CONSULT-II BASIC OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be D
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON-
SULT-II CONVERTER to the data link connector, then turn igni- E
tion switch ON.
BBIA0538E
H
2. Touch "START (NISSAN BASED VHCL)".
DI
BCIA0029E
BCIA0030E
BCIA0031E
SELF-DIAGNOSTIC RESULTS
Operation Procedure
1. Touch "SELF-DIAG RESULTS" on "SELECT DIAG MODE" screen.
2. Self-diagnosis results are displayed.
SKIA4956E
"TIME" indicates the condition of the self-diagnosis results judged by each signal input.
● Normal: If the system is presently operating properly, but had a malfunction in the past, the time will indi-
cate "1-63".
● Malfunction: Soon after detecting malfunctions by self-diagnoses or current malfunction, "0" is indicated.
After the system returns to normal operating condition, every time the ignition switch is cycled (turned to OFF
from ON), a value of one is added to the counter (i.e. "1"→"2"→"3"···"63"). When the ignition switch is cycled
64 times, the result of the self-diagnoses will be erased. If a malfunction is detected again, "0" will be indi-
cated.
DATA MONITOR
Operation Procedure
1. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
2. Touch either "MAIN SIGNALS" or "SELECTION FROM MENU" on the "DATA MONITOR" screen.
3. Touch "START".
SKIA4957E
D
Display Item List
MAIN SELECTION
Display item [Unit] Contents
SIGNALS FROM MENU
E
This is the angle correction value after the speed signal
SPEED METER [km/h] or [mph] X X from the ABS actuator and electric unit (control unit) is con-
verted into the vehicle speed.
F
This is the angle correction value before the speed signal
SPEED OUTPUT [km/h] or [mph] X X from the ABS actuator and electric unit (control unit) is con-
verted into the vehicle speed.
This is the converted value for the engine speed signal from G
TACHO METER [rpm] X X
the ECM.
This is the converted value for the water temp signal from
W TEMP METER [°C] or [°F] X X
the ECM. H
This is the processed value for the signal (resistance value)
FUEL METER [lit.] X X
from the fuel gauge.
This is the calculated value for the speed signal from the I
ABS actuator and electric unit (control unit), the signal
DISTANCE [km] X X
(resistance signal) from the fuel gauge and fuel consump-
tion from ECM.
J
FUEL W/L [ON/OFF] X X Indicates [ON/OFF] condition of low-fuel warning lamp.
C-ENG W/L [ON/OFF] X Indicates [ON/OFF] condition of malfunction indicator lamp.
Indicates [ON/OFF] condition of low tire pressure indicator DI
AIR PRES W/L [ON/OFF] X
lamp.
SEAT BELT W/L [ON/OFF] X Indicates [ON/OFF] condition of seat belt warning lamp.
BUZZER [ON/OFF] X X Indicates [ON/OFF] condition of buzzer. L
DOOR W/L [ON/OFF] X Indicates [ON/OFF] condition of door warning lamp.
HI-BEAM IND [ON/OFF] X Indicates [ON/OFF] condition of high beam indicator.
M
TURN IND [ON/OFF] X Indicates [ON/OFF] condition of turn indicator.
OIL W/L [ON/OFF] X Indicates [ON/OFF] condition of oil pressure warning lamp.
VDC/TCS IND [ON/OFF] X Indicates [ON/OFF] condition of VDC OFF indicator lamp.
ABS W/L [ON/OFF] X Indicates [ON/OFF] condition of ABS warning lamp.
SLIP IND [ON/OFF] X Indicates [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L [ON/OFF] X Indicates [ON/OFF] condition of brake warning lamp.*
KEY G W/L [ON/OFF] X Indicates [ON/OFF] condition of key warning lamp (green).
KEY R W/L [ON/OFF] X Indicates [ON/OFF] condition of key warning lamp (red).
KEY KNOB W/L [ON/OFF] X Indicates [ON/OFF] condition of key knob warning lamp.
M RANGE SW [ON/OFF] X X Indicates [ON/OFF] condition of manual mode range switch.
Indicates [ON/OFF] condition of except for manual mode
NM RANGE SW [ON/OFF] X X
range switch.
AT SFT UP SW [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift-up switch.
AT SFT DWN SW [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift-down switch.
MAIN SELECTION
Display item [Unit] Contents
SIGNALS FROM MENU
O/D OFF SWITCH [ON/OFF] X Indicates [ON/OFF] condition of O/D OFF switch.
BRAKE SW [ON/OFF] X Indicates [ON/OFF] condition of parking brake switch.
AT-M IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T manual mode indicator.
Indicates [1, 2, 3, 4, 5] condition of A/T manual mode gear
AT-M GEAR [1, 2, 3, 4, 5] X X
position.
P RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift P range indicator.
R RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift R range indicator.
N RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift N range indicator.
D RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift D range indicator.
4 RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift 4 range indicator.
3 RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift 3 range indicator.
2 RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift 2 range indicator.
1 RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift 1range indicator.
O/D OFF W/L [ON/OFF] X Indicates [ON/OFF] condition of O/D OFF indicator lamp.
CRUISE IND [ON/OFF] X Indicates [ON/OFF] condition of CRUISE indicator.
SET IND [ON/OFF] X Indicates [ON/OFF] condition of SET indicator.
4WD LOCK SW [ON/OFF] X Indicates [ON/OFF] condition of 4WD lock switch.
4WD LOCK IND [ON/OFF] X Indicates [ON/OFF] condition of 4WD lock indicator.
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
*: Monitor keeps indicating “OFF” when brake warning lamp is on because of parking brake operation or low
brake fluid level.
A
1. Confirm the symptom or customer complaint.
2. Perform diagnosis according to diagnosis flow. Refer to DI-21, "Diagnosis Flow" .
3. According to the symptom chart, repair or replace the cause of the symptom.
B
4. Does the meter operate normally? If so, go to 5. If not, go to 2.
5. Inspection End.
Diagnosis Flow EKS00BSO
C
1. CHECK WARNING INDICATOR ILLUMINATION
1. Turn ignition switch ON. D
2. Make sure warning indicators (such as malfunction indicator lamp and oil pressure warning indicator) illu-
minate.
Do warning indicators illuminate? E
YES >> GO TO 2.
NO >> Check ignition power supply system of combination meter. Refer to DI-22, "Power Supply and
Ground Circuit Inspection" . F
LKIA0581E
1. CHECK FUSES
Check for blown combination meter fuses.
Unit Power source Fuse No.
Battery 19
Combination meter
Ignition switch ON or START 14
Refer to DI-10, "Wiring Diagram — METER —" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
OK or NG
OK >> GO TO 3.
NG >> Check the harness for open between combination meter and fuse.
Terminals
(+) Continuity
(–)
Connector Terminal
13
M24 Ground Yes
23
OK or NG
WKIA3280E
OK >> Inspection End.
NG >> Repair harness or connector.
A
Trouble phenomenon Possible cause
Improper tachometer indication. Refer to DI-25, "Engine Speed Signal Inspection" .
Improper water temperature gauge indication. Refer to DI-25, "Water Temperature Signal Inspection" . B
Improper speedometer or odometer. Refer to DI-23, "Vehicle Speed Signal Inspection" .
Improper fuel gauge indication.
Refer to DI-26, "Fuel Level Sensor Unit Inspection" . C
Fuel warning lamp indication is irregular.
Improper voltage gauge indication. Replace combination meter. Refer to IP-12, "COMBINATION
More than one gauge does not give proper indication. METER" .
D
Improper A/T position indication. Refer to DI-48, "A/T INDICATOR" .
Replace combination meter. Refer to IP-12, "COMBINATION
Illumination control does not operate properly.
METER" . E
OK or NG WKIA3281E
OK >> GO TO 2. M
NG >> GO TO 3.
WKIA3283E
WKIA3284E
WKIA3285E
OK or NG
OK >> Replace oil pressure sensor.
C
NG >> Repair harness or connector.
D
WKIA3286E
Perform ECM self-diagnosis. Refer to EC-135, "SELF-DIAG RESULTS MODE" (QR25DE) or EC-761, "SELF-
DIAG RESULTS MODE" (VQ40DE). I
OK or NG
OK >> Replace the combination meter. Refer to IP-12, "COMBINATION METER" .
NG >> Perform "Diagnostic procedure" for displayed DTC. J
DI
Symptom: Display CAN COMM CIRC [U1000] at the result of self-diagnosis for combination meter.
1. CHECK CAN COMMUNICATION
1. Select "SELF-DIAG RESULTS" mode for "METER" with CONSULT-II.
2. Print out CONSULT-II screen.
Symptom: Display VEHICLE SPEED CIRC [B2205] at the result of self-diagnosis for combination meter.
1. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BRC-24, "SELF-DIAGNOSIS"
(ABS), BRC-64, "SELF-DIAGNOSIS" (ABLS/ABS) or BRC-116, "SELF-DIAGNOSIS" (HDC/HSA/VDC/TCS/
ABS).
Are self-diagnosis result items displayed?
YES >> After checking and repairing the applicable item, perform the ABS actuator and electric unit (con-
trol unit) self-diagnosis again.
NO >> Replace combination meter. Refer to IP-12, "COMBINATION METER" .
F
Refer to IP-12, "COMBINATION METER" .
DI
LKIA0447E
DI
WKWA2837E
2. WARM UP CHECK
1. Leave the vehicle for 10 minutes.
2. With the ignition switch in the ON position, disconnect and reconnect the ambient sensor 2 connector.
Does the indicated temperature rise?
YES >> The system is OK.
NO >> The system is malfunctioning. Refer to DI-32, "INSPECTION/COMPASS AND THERMOMETER"
.
INSPECTION/COMPASS AND THERMOMETER
Symptom Possible causes Repair order
No display at all 1. 10A fuse. 1. Check 10A fuse [No. 14 located in the fuse block (J/B)].
2. Power circuit. Turn the ignition switch ON and verify that battery positive volt-
age is at terminal 6 (with Homelink® universal transceiver) or 7
3. Ground circuit.
(without Homelink® universal transceiver) of auto anti-dazzling
4. Auto anti-dazzling inside mirror. inside mirror.
2. Check power circuit for auto anti-dazzling inside mirror.
3. Check ground circuit for auto anti-dazzling inside mirror.
4. Replace auto anti-dazzling inside mirror.
Forward direction indi- 1. In manual correction mode (Bar and 1. Drive the vehicle and turn at an angle of 90°.
cation slips off the mark display vanish). 2. Perform the zone variation change.
or incorrect. 2. Zone variation change is not done.
Displays wrong tem- 1. Check operation. 1. Perform preliminary check shown above.
perature when ambient 2. Ambient sensor 2 circuit. 2. Check harness for open or short between ambient sensor 2 and
temperature is between auto anti-dazzling inside mirror.
3. Ambient sensor 2.
−40°C (−40°F) and
4. Auto anti-dazzling inside mirror. 3. Replace ambient sensor 2.
55°C (130°F)
4. Replace auto anti-dazzling inside mirror.
Displays SC or OC 1. Ambient sensor 2 circuit. 1. Check harness for open or short between ambient sensor 2 and
2. Ambient sensor 2. auto anti-dazzling inside mirror.
3. Auto anti-dazzling inside mirror. 2. Replace ambient sensor 2.
3. Replace auto anti-dazzling inside mirror.
A
The difference between magnetic North and geographical North can sometimes be great enough to cause
false compass readings. In order for the compass to operate accurately in a particular zone, it must be cali-
brated using the following procedure.
B
J
WKIA3455E
LKIA0447E
Schematic EKS00BT5
WKWA2829E
DI
WKWA2830E
WKWA2831E
CREW CAB
A
DI
WKWA2832E
KING CAB
WKWA2833E
DI
LKWA0303E
WKWA2879E
DI
WKWA2834E
WKWA2835E
DI
WKWA2836E
Oil Pressure Warning Lamp Stays Off (Ignition Switch ON) EKS00BT7
QR25DE Models
1. CHECK IPDM E/R OUTPUT SIGNAL
Activate IPDM E/R auto active test. Refer to PG-22, "Auto Active Test" .
Is oil pressure warning lamp blinking?
YES >> GO TO 4.
NO >> GO TO 2.
VQ40DE Models
1. CHECK OIL PRESSURE SENSOR SIGNAL A
OK or NG WKIA3281E
E
OK >> GO TO 2.
NG >> GO TO 3.
F
2. CHECK OIL PRESSURE SENSOR GROUND CIRCUIT
1. Turn ignition switch OFF.
G
2. Disconnect combination meter connector M24 and oil pressure
sensor connector E208.
3. Check continuity between combination meter harness connector H
M24 terminal 10 and oil pressure sensor harness connector
E208 terminal 3.
Continuity should exist. I
OK or NG
OK >> Replace the combination meter. Refer to IP-12, "COM-
WKIA3282E
BINATION METER" . J
NG >> Repair harness or connector.
WKIA3283E
WKIA3284E
WKIA3285E
WKIA3286E
Oil Pressure Warning Lamp Does Not Turn Off (Oil Pressure Is Normal) EKS00BT8
A
NOTE:
For oil pressure inspection, refer to LU-6, "OIL PRESSURE CHECK" (QR25DE) or LU-19, "OIL PRESSURE
CHECK" (VQ40DE).
B
QR25DE Models
1. CHECK OIL PRESSURE SWITCH CIRCUIT
C
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector E122 and oil pressure switch
connector F4.
D
3. Check continuity between IPDM E/R harness connector E122
terminal 42 and ground.
Continuity should not exist. E
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector. F
WKIA3487E
ELF0044D
WKWA2122E
DI
WKIA3998E
FUNCTION A
Power is supplied at all times
● through 50A fusible link (letter g , located in the fuse and fusible link box)
B
● to BCM terminal 70, and
● through 10A fuse (No. 25, located in the fuse and fusible link box)
● to key switch terminal 2.
C
With ignition switch in ON or START position, power is supplied
● through 10A fuse [No. 1, located in the fuse block (J/B)]
● to BCM terminal 38. D
Ground is supplied
● to BCM terminal 67
● through body grounds M57, M61, and M79. E
NOTE:
When ignition key warning chime, light warning chime, and seat belt warning chime are required at the same
time, the priorities for each chime are the following. F
1. Light warning chime
2. Ignition key warning chime
3. Seat belt warning chime G
BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter via CAN
communication lines. When the combination meter receives key warning signal, it sounds warning chime.
SEAT BELT WARNING CHIME
When the ignition switch is turned ON with the driver seat belt unfastened (seat belt buckle switch LH unfas-
tened), warning chime will sound for approximately 6 seconds.
Ground is supplied
● to combination meter terminal 24
● through seat belt buckle switch LH terminal 1.
Seat belt buckle switch LH terminal 2 is grounded through body grounds B7 and B19.
The combination meter sends seat belt buckle switch LH unfastened signal to BCM via CAN communication
line.
BCM receives seat belt buckle switch LH unfastened signal from combination meter via CAN communication
line, and sends seat belt warning signal to the combination meter via CAN communication line. When the
combination meter receives the seat belt warning signal, it sounds the warning chime. The BCM controls the
(6 second) duration of the seat belt warning chime.
CAN Communication System Description EKS00BTD
DI
WKWA2880E
WKWA3009E
A
Condition
Terminal Wire Reference value (V)
Item Ignition
No. color Measurement method (Approx.)
switch
B
SKIA5291E
D
G
● Light switch and wiper switch
4 V Combination switch input 3 ON OFF
● Wiper dial position 4 H
SKIA5291E
SKIA5292E
DI
SKIA5291E M
SKIA5292E
SKIA5291E
Condition
Terminal Wire Reference value (V)
Item Ignition
No. color Measurement method (Approx.)
switch
35 BR Combination switch output 2
SKIA5292E
Key is removed 0V
37 B Key switch signal OFF
Key is inserted Battery voltage
38 W/R Ignition switch ON or START ON — Battery voltage
39 L CAN-H — — —
40 P CAN-L — — —
ON (open) 0V
47 GR Front door switch LH signal OFF
OFF (closed) 5V
67 B Ground — — 0V
70 W Battery power supply OFF — Battery voltage
Condition
Terminal Wire Reference value (V)
Item Ignition
No. color Measurement method (Approx.)
switch
11 P CAN-L — — —
12 L CAN-H — — —
Unfastened (ON) 0V
24 V Seat belt buckle switch LH ON
Fastened (OFF) Battery voltage
OK or NG E
OK >> GO TO 3.
NG >> Check harness for open between BCM and fuse.
F
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
G
2. Check continuity between BCM harness connector M20 terminal
67 and ground.
Continuity should exist. H
OK or NG
OK >> Inspection End.
NG >> Repair harness or connector. I
J
LIIA0915E
DI
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
BCM
Diagnostic mode Description
diagnostic test item
Supports inspections and adjustments. Commands are transmitted to the BCM
WORK SUPPORT for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
Inspection by part
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.
BBIA0538E
BCIA0029E
BCIA0030E
SKIA5788E
D
5. Select "DATA MONITOR" or "SELF-DIAG RESULTS".
G
BCIA0031E
DATA MONITOR
H
Operation Procedure
1. Touch "BUZZER" on "SELECT TEST ITEM" screen.
2. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
I
3. Touch "ALL SIGNALS" or "SELECTION FROM MENU" on "DATA MONITOR" screen.
ALL SIGNALS Monitors main items.
SELECTION FROM MENU Selects and monitors items. J
4. If "SELECTION FROM MENU" is selected, touch the item you desire to monitor. If "ALL SIGNALS" is
selected, all control items are monitored.
DI
5. Touch "START".
6. During monitoring, touching "RECORD" can start recording the monitored item status.
Display Item List L
Monitored item Description
IGN ON SW Indicates [ON/OFF] condition of ignition switch.
M
KEY ON SW Indicates [ON/OFF] condition of key switch.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch (driver side).
LIGHT SW 1ST Indicates [ON/OFF] condition of lighting switch.
BUCKLE SW Indicates [ON/OFF] condition of seat belt buckle switch LH.
ACTIVE TEST
Operation Procedure
1. Touch "BUZZER" on "SELECT TEST ITEM" screen.
2. Touch "ACTIVE TEST" on "SELECT DIAG MODE" screen.
3. Touch the item to be tested, and check the operation.
4. During the operation check, touching "OFF" deactivates the operation.
SELF-DIAGNOSTIC RESULTS
Operation Procedure
1. Touch "BCM" on "SELECT TEST ITEM" screen.
2. Touch "SELF-DIAG RESULTS" on "SELECT DIAG MODE" screen.
3. Self-diagnostic results are displayed.
Display Item List
Monitored Item CONSULT-II display Description
CAN communication CAN communication [U1000] Malfunction is detected in CAN communication.
NOTE:
If "CAN communication [U1000]" is indicated, after printing the monitor item, go to "CAN System". Refer to
LAN-22, "CAN COMMUNICATION" .
All Warning Chimes Do Not Operate EKS00BTK
SKIA6331E
Key Warning Chime and Light Warning Chime Do Not Operate (Seat Belt Warn-
ing Chime Does Operate) EKS00BTL
A
1. CHECK BCM INPUT SIGNAL
With CONSULT-II B
1. Select "BCM" on CONSULT-II.
2. With "DATA MONITOR" of "BUZZER", confirm "DOOR SW-DR"
changes with the status of front door LH. C
LKIA0335E
F
Without CONSULT-II
Check voltage between BCM harness connector M19 terminal 47
and ground. G
When front door LH is : Approx. 0V
opened
When front door LH is : Approx. 5V H
closed
OK or NG
I
OK >> Replace the BCM. Refer to BCS-19, "Removal and
Installation of BCM" .
NG >> GO TO 2. WKIA1515E
J
2. CHECK FRONT DOOR SWITCH LH CIRCUIT
1. Turn ignition switch OFF. DI
2. Disconnect BCM connector M19 and front door switch LH con-
nector B8 (Crew Cab) or D213 (King Cab).
3. Check continuity between BCM harness connector M19 terminal L
47 and front door switch LH harness connector B8 terminal 2
(Crew Cab) or connector D213 terminal 2 (King Cab).
Continuity should exist. M
4. Check continuity between BCM harness connector M19 terminal
47 and ground.
Continuity should not exist. WKIA1516E
OK or NG
OK >> King Cab, GO TO 3. Crew Cab, GO TO 4.
NG >> Repair harness or connector.
WKIA3457E
WKIA3733E
KING CAB
Check continuity between front door switch LH terminals 2 and 3
while pressing and releasing switch.
When front door switch : Continuity should exist.
LH is released
When front door switch : Continuity should not
LH is pushed exist.
OK or NG
OK >> Replace the BCM. Refer to BCS-19, "Removal and
Installation of BCM" .
NG >> Replace the front door switch LH. WKIA3734E
1. CHECK FUSE
Check if the key switch fuse (No. 25, located in the fuse and fusible link box) is blown. Refer to DI-53, "Wiring
Diagram — CHIME —" .
Is the fuse blown?
YES >> Replace the fuse. Be sure to repair the cause of malfunction before installing new fuse.
NO >> GO TO 2.
SKIA1960E
E
Without CONSULT-II
Check voltage between BCM harness connector M18 terminal 37
and ground. F
Terminals
(+) Condition Voltage (V)
(–) G
Connector Terminal
Key is inserted Battery voltage
M18 37 Ground
Key is removed 0V H
OK or NG
LKIA0255E
OK >> Replace the BCM. Refer to BCS-19, "Removal and
Installation of BCM" . I
NG >> GO TO 4.
OK or NG M
OK >> GO TO 5.
NG >> Replace the key switch.
WIIA0559E
WKIA3477E
1. With key removed from the ignition and the front door LH open, turn the lighting switch to 1st or 2nd posi-
tion. B
2. Return lighting switch to OFF position, and insert key into ignition.
Does warning chime sound for both steps?
YES >> GO TO 2. C
NO >> Go to DI-60, "All Warning Chimes Do Not Operate" .
WKIA3294E
OK or NG
L
OK >> Replace the combination meter. Refer to IP-12, "COMBINATION METER" .
NG >> GO TO 4.
OK or NG
OK >> GO TO 5.
NG >> Replace the seat belt buckle switch LH.
WKIA1522E
FUNCTION
The board computer can indicate the following items. B
● DTE (distance to empty)
● Trip distance
● Trip time C
● Average fuel consumption
● Average vehicle speed
D
DTE (DISTANCE TO EMPTY) INDICATION
The range indication provides the driver with an estimation of the distance that can be driven before refueling.
The range is calculated by signals from the fuel level sensor unit (fuel remaining), ECM (fuel consumption)
and the ABS actuator and electric unit (vehicle speed). The indication will be refreshed every 30 seconds. E
When fuel remaining is less than approximately 11.6 (3 1/8 US gal, 2 1/2 Imp gal), the indication will blink as
a warning. If the fuel remaining is less than approximately 9.6 (2 1/2 US gal, 2 1/8 Imp gal), the indication will
show "---". In this case, the display will change to the DTE mode even though the display is showing a different F
mode. When the battery is disconnected and reconnected, DTE mode will display "---" until the vehicle is
driven 0.3 miles (0.5 km).
TRIP DISTANCE G
Trip distance is calculated by signal from the ABS actuator and electric unit (vehicle speed). If trip distance is
reset, trip time will be reset at the same time.
H
TRIP TIME
Trip time displays cumulative ignition switch ON time. If trip time is reset, trip distance will be reset at the same
time.
I
AVERAGE FUEL CONSUMPTION
Average fuel consumption indication is calculated by signals from the ABS actuator and electric unit (vehicle
speed) and the ECM (fuel consumption). The indication will be refreshed every 30 seconds. J
AVERAGE VEHICLE SPEED
Average vehicle speed indication is calculated by running distance and running time. The indication will be
refreshed every 30 seconds. If average vehicle speed is reset, average fuel consumption will be reset at the DI
same time. After resetting, the display will show "---" for 30 seconds.
HOW TO CHANGE/RESET INDICATION
L
Indication can be changed in the following order by momentarily depressing the board computer switch.
Trip distance → dte → Average vehicle speed → Average fuel consumption → Trip time→.
Holding the switch for more than 1 second will reset the indication of the currently displayed mode (trip dis-
tance, trip time, average vehicle speed or average fuel consumption). M
NOTE:
After the display changes automatically, the indication can be changed to the next mode by pushing the board
computer switch.
CAN Communication System Description EKS00BTQ
WKWA2838E
SEGMENT CHECK A
The board computer segment display can be checked by entering combination meter self-diagnostic mode.
Refer to DI-13, "SELF-DIAGNOSIS FUNCTION" .
B
PRELIMINARY CHECK
J
WKIA3296E