12 11 10 9 8

7 6 5 4
rgA
3 2

SYMBOL UNI LS5 9THERWISI SPEGIFIED

P A R T MUST CONFORM To SpECiF iCATION ES-0280
5C74CG» PER SPECIFICAT ON ESOO010060, IF APPL ICABLE
0,
REMOVE ALL BURRS
0,5 DUNLESS OTHE RWISE SPECIFIED ALL WACHINEO SURFACES TO BE 0,4

5 FOR CROSSHOLE AND LUC MACHINING SEE SUMMARY 1330-1

FOR SPLINE OATA_SEE20SPLTNE SUMMARY SS1338-20-I-2
TEETH WIDE TOOTH °ACE TO BE IN LINE
DETAIL X 8WI TH
TEETHASEO ON
CROSS_HOLES
SCALE 4:1 COMANUF ACTURE PER SPECIFICAT ON 545
8 NON CLEANUP PERM! TTED
G

37. 5 -
25
44. VIEW X
-9.
-R12
863 5
R1.5
R
- SPL INE MI NOR DIA dO.5|A 40.25 A
1.5XYZ
p44
p35

ZZZ7IZZZZIITZZ
0.25A
p42.5 e48:435
0.25 B - RE 0 . 13JA
VIEWY
4656 R.76
0 . 13A
3.03
45 5 6
o.13A D
- 177-

LO 25 A

MAKE FROM WAS 5005728 HG GVB 2018-01-05

36 o004131C|
01 RELEASED TO PROOUCTION HG VCG| 2017-10-18C
boo3803 B
ADDED NOTE B
20 REDESIGNEO
1 01 RELEASED TO PROTOTYPE |HC VCC 2016-07-20
DR CHKDATE
0O00138A01
REVISION
NO REVSHZONE PRODUCTION_
42.5) 3 PART STATUS FORMAT

UNLESS OTHERWISE
SPECIFIED:
A1
FINISH TOLERANCE: #0.5

t5° SHEET
TOL ERANCE
ONING AND TOLERANCI NG
ANGLE
01 OF 01
ARE IN MILL IMETERS DIMENSI
PER ASME Y14,SM199
DIMENSIONS

LIGHT VEHcLE DRVELNE

Lo ESOO011334 S PRODUCTSOROUP

- R0,4 MAX
REF DRAWI
NG 5005575, 10045622
MAKE FROM 10092381 SLIP YOKE
RO.4 MAX
WR
APPROX W *9 A
20 SCALE
DRAWING NO.

|MOOEL
1330
10008233
O0001J8T
60
TARGET CONE
DETAILY WORK ORDER
RMAT S YTYYWW-DD

DATEFon
 10/9/2021
MarWin QE Contour
11:11:18
Mahr) 6.00-20 SP1 Task: "Contour"
Inspector
ANKUSH
Part: Drawing n°: Machining operation.
SY 100082333 TAIL END ID Signature:
3
Comment:
OK
X:10.73; Z:10.73; 10.31°
Meas. instrument: MarTalk
Drive unit: DriveUnit.CD 120
Probe: Small probe 123456
Lt: 4.40 mm
Ls: ****************************************************** ********************************
VB: +/-13124.7 um
Vt: 1.00 mm/s
Points: 4338
1.45718 mm
30.0
T T
173
179
T T T* T
181 183 mm
Contour results
a (M02) 30.0 0.0
dz(M05) 2.52579 mm 0.00000
0.0
dx(M07) 1.45718 mm 0.00000 0.00000
0.0000ol
 MarWin QE Contour 10/9/2021
(Mahr) 6.00-20 sP 1 Task: "Contour" 11:09:09
Inspector
Part
Drawing n Machining operation. ANKUSH
SY 100082333 TAIL END ID Signature:
2
Comment
OK
Meas. instrument: MarTalk X:11.12; Z:10.26; 10.03°
Drive unit: DriveUnit. CD 120
Probe: Small probe 123456
Lt: 4.41 mm
Ls:
VB: +/-13124.7 um
Vt 1.00 mm/s
Points: 4319
Zoom is not proportional|
30.4
1.59879 mm
172 174 176 178 180 182 184
Contour results
a(M02) 30.4 0.0 0.0
|dz(M03) 2.71625 mm 0.00000 0.00000
dx(M04) 1.69879 mm 0.00000 0.00000
 10/9/2021
MarWin QE Contour 11:03:18
(Mahr) 6.00-20 SP1 Task: "Contour" ipspector
Machining operation:
ANKUSH
Drawing n
Part TAIL END ID Signature
SY 10008233
1
V2021 1
:09
Comment tor:
OK
USH
X:7.19; Z:7.19; 5.720 e:
Meas. instrument: MarTalk
Drive unit DriveUnit.CD 120
****"******************************************"*********
Small probe 123456
Probe
Lt: 4.72 mm
Ls
VB: +/-13124.7 um .03
Vt 1.00 mm/s
4702
Points
29.8
.53730 mm
oportionai
184 186 188
178 180 182
168 170 72 174 176
Contour results 0.00000
1.53730 mm 0.00000 35.0
Idx(M03) 26.0