Professional Documents
Culture Documents
Ve 20SN
Ve 20SN
2009 VE-20
SERVICE NOTES
Issued by RJA
Table of Contents
Cautionary Notes ..............................................................2 Verifying the Version Numbers ....................................14
Specifications .....................................................................3 Data Backup .....................................................................14
Location of Controls .........................................................4 Performing a Factory Reset............................................14
Exploded View (1).............................................................5 Updating the System ......................................................14
Exploded View (1) Parts List ...........................................5 Test Mode .........................................................................14
Exploded View (2).............................................................6 Circuit Board (Jack, In, Out, Adaptor, Panel, Enc
Exploded View (2) Parts List ...........................................7 Board)................................................................................20
Exploded View (3).............................................................8 Circuit Diagram (Jack Board: 1/2)................................22
Exploded View (3) Parts List ...........................................8 Circuit Diagram (Jack Board: 2/2, In, Out, Adaptor
Important Notes When Assembling...............................9 Board)................................................................................24
Wiring Diagram...............................................................11 Circuit Diagram (Panel, Enc Board) .............................26
Parts List ...........................................................................12
Cautionary Notes
Part Replacement
When replacing components near the power-supply circuit or a heat-
generating circuit (such as a circuit provided with a heat sink or including a
cement resistor), carry out the procedure according to the instructions with
respect to the part number, direction, and attachment position (mounting so as
to leave an air gap between the component and the circuit board, etc.).
Parts List
A component whose part code is ******** will not be supplied as a service part
because one of the following reasons applies.
• Because it is supplied as an assembled part (under a different part code).
• Because a number of circuit boards are grouped together and supplied as
a single circuit board (under a different part code).
• Because supply is prohibited due to copyright restrictions.
• Because reissuance is restricted.
• Because the part is made to order (at current market price).
• Because it is carried in electronic data on the Roland web site.
• Because it is a package or an accessory irrelevant to the function
maintenance of the main body.
• Because it can be replaced with an article on the market. (battery or etc.)
Circuit Diagram
In the circuit diagram, “NIU” is an abbreviation for “Not in Use,” and
“UnPop” is an abbreviation for “Unpopulated.” They both mean non-mounted
components. The circuit board and circuit board diagram show silk-screened
indications, but no components are mounted.
2
Nov. 2009 VE-20
Specifications
Option
Nominal Output Level AC Adaptor: PSA series
OUTPUT: -40 dBu
PHONES/LINE: -25 dBu
Output Impedance
OUTPUT: 600 Ω * 0 dBu = 0.775 Vrms
PHONES/LINE: 66 Ω * Printed matters will not be supplied after the end of the production. Then,
download the electronic file from the Roland web site.
Display
16 characters, 2 lines (backlit LCD)
Connectors
INPUT jack (XLR type (balanced, phantom power +48 V)
1/4 inch TRS phone type (balanced))
OUTPUT jacks (XLR type)
PHONES/LINE jack (Stereo 1/4 inch phone type)
DC IN jack (DC 9 V)
Power Supply
DC 9 V: Dry battery LR6/R6 (AA) type x 6
AC Adaptor (PSA series)
* Duration of continuous use with battery operation:
Carbon: 2 hours, Alkaline: 8 hours
These figures will vary depending on the actual conditions of use.
Current Draw
190 mA (9 V max.)
Dimensions
173 (W) x 158 (D) x 57 (H) mm
6-13/16 (W) x 6-1/4 (D) x 2-1/4 (H) inches
Weight
1.1 kg / 2 lbs 7 oz (including batteries)
3
Nov. 2009 VE-20
Location of Controls
fig.panel.eps
2 3
a a
8 4 5 b
6 7 6 7
a a
11
12
13
9 10 9
14
15 16 18 19
17
d e
4
Nov. 2009 VE-20
b 8
2 9
a
5
c
3
4
5
Nov. 2009 VE-20
b 9
11
10
d
b
10
k 5
e
f
6
Nov. 2009 VE-20
fig.bunkaizu-2.eps@R
m
4 7 c
7
Nov. 2009 VE-20
3 2
a
9
1
a
8
7
8
b
6
8
Nov. 2009 VE-20
fig.FPC3-NG.eps
* Affix so that the portion of the LCD FPC shown by dotted lines is free of slack.
Not OK
9
Nov. 2009 VE-20
fig.keyunit-2.eps
10
Nov. 2009 VE-20
Wiring Diagram
fig.wiring.eps
BACKLIGHT WIRING
CN CN ENC
CN
504 B 503 BOARD
500
LCD UNIT
PANEL BOARD
CN502 CN501
D LCD
FPC
E
CN4 CN1
CN3
BATTERY CASE
Red Black
A JACK BOARD
CN20
CN6
CN12 CN7
C C
B
CN8
CN13 CN5
ADAPTOR OUT BOARD IN BOARD
BOARD
* LCD FPC and Backlight wiring of LCD unit are included in LCD PE1602MRT-012-I-Q (#5100010065).
11
Nov. 2009 VE-20
Parts List
fig.-part1-e.eps
Note: The parts marked # are new. (initial parts) The description “Q’ty” means a necessary number of the parts per one product.
CASING
# 5100007755 CASE 1
# 5100007757 REAR PANEL 1
# 5100007758 LED PANEL 1
# 5100007759 PANEL 1
# 5100007763 PEDAL L 1
# 5100007764 PEDAL R 1
# 5100008053 BOTTOM COVER (75D422E0R0) 1
# 5100008056 BATTERY COVER (G2017621R0) 1
CHASSIS
# 5100008055 PEDAL PLATE 62X53 (G2357116R0) 2
KNOB, BUTTON
# 5100008051 R-KNOB (G2477525R1) 1
# 5100007761 KEYUNIT 1
SWITCH
01780101 TACT SWITCH SKQKABD010 6
03344723 TACT SWITCH SKQKAKD010 2
# 5100002859 SWITCH SK22F02 G10 1
DISPLAY UNIT
# 5100010065 LCD PE1602MRT-012-I-Q 1
PWB ASSY
# 5100006776 JACK SHEET ASSY JACK+PANEL BOARD (75E623J0R0) 1
* This unit includes the following parts.
# ******** PANEL BOARD ASSY 1
# ******** JACK BOARD ASSY 1
# ******** IN BOARD 1
# ******** OUT BOARD 1
# ******** ADAPTOR BOARD 1
# ******** ENC BOARD 1
DIODE
03349978 LED (RED) L-34HDSL-FPB 1
03349989 LED (GREEN) L-34GDSL-FPB 2
# 05017534 LED L-34YDSL 1
F5029126R0 LED (GREEN) L-113GDT-F01 1
ENCODER
# 5100009149 ENCODER EVYBAVD0120B 1
WIRING, CABLE
# 5100007871 WIRING L=80MM 2P (G3487163R0) 1
# 5100010465 WIRING 3P L=53X6X6MM P=2.0 2
# 5100010466 WIRING 8P L=45X6X6MM P=2.0 1
# 5100010467 WIRING 6P L=45X6X6MM P=2.0 2
# 5100010468 WIRING 12P L=45X6X6MM P=2.0 1
12
Nov. 2009 VE-20
SCREWS
# 5100008243 SCREW 2.6X5 (H5019430R0) BINDING HEAD TAPTITE P FEZC 2
# 5100008242 SCREW 3X6 (H5019110R0) PAN TAPPING B1 ZC 13
40011312 SCREW 3X8 BINDING TAPTITE P FE BZC 6
# 5100008245 SCREW 3X8 (H5019115R0) PAN TAPPING B1 BZC 7
# 5100008244 SCREW M4X8 (H5029855R0) HEXAGON BUTTON HEAD FE NI 4
# 5100008241 BTN M4D3 BOLT BZC (H5029852R0) 2
5100003918 JACK NUT M9X12X2 NI RTC(H5039510R0) 1
5100003926 WASHER 9X13.5X0.5T NI(H5039158R0) 1
5100008086 INT TOOTH WASHER 9.5X12.5X0.5 NI RTC(H5039205R0) 1
# 5100008291 RESIN WASHER 4.1X7.5X0.5 BK (H5039413R0) 2
# 5100008293 RESIN WASHER 5.1X9.5X0.5 BK (H5039414R0) 2
MISCELLANEOUS
04560601 CUSHION R (G2357111) 2
5100007504 COIL SPRING (22177109R0) 2
5100007505 PEDAL GUIDE BUSH (22157702R0) 2
# 5100007756 INSULATING SHEET CENTER 1
# 5100007760 DISPLAY COVER 1
# 5100007817 LED GUIDE (G2197126R0) 1
# 5100008052 BOTTOM FOOT (G2357118R0) 2
# 5100008054 PEDAL FOOT (G2357115R0) 2
# 5100008058 TWIN PEDAL BATTERY CASE V6 (G2017620R0) 1
# 5100008057 BATTERY INSULATING SHEET (G2257130R0) 1
# 5100008059 BATTERY TERMINAL (+) (G2177308R0) 1
# 5100008060 BATTERY TERMINAL (+-) (G2177307R1) 1
# 5100008061 BATTERY TERMINAL (-) (G2177309R1) 1
# 5100008065 BOTTOM LABEL 1
# 5100008237 PEDAL SHAFT (H5029851R0) 2
# 5100011120 3M FILAMENT TAPE #898 W10MM -
ACCESSORIES (Standard)
# 5100007403 OWNER’S MANUAL JAPANESE (G6017480R0) 1
# 5100007404 OWNER’S MANUAL ENGLISH (G6027133R0) 1
13
Nov. 2009 VE-20
4. Press [ ].
5. Verify that the message ALL is displayed on the lower line of the LCD
screen and the REC LED flashes.
* To cancel the factory reset, press [EXIT] to go back to the original screen.
7. When the message COMPLETED! appears, turn off the [POWER] switch. Ammeter
14
Nov. 2009 VE-20
OK! is displayed for the results of the device check at the lower line of the
LCD screen.
LCD
* If an error occurs, the message ERROR! is displayed. For information about the 1. Verify that the message LCD is displayed on the LCD screen.
details of the error, refer to the Test-mode DEVICE CHECK section below.
2. Press [ ] and verify that the LCD screen goes dark.
fig.LCD-blk.eps
15
Nov. 2009 VE-20
3. Press the buttons in the following chart in the indicated numerical order. D/A Check
* The name of the LED darkened when the button was pressed is displayed on the
1. Verify that the message DA is displayed on the LCD screen.
left side of the lower line of the LCD screen, and the name of the button to press
next is displayed on the right side. 2. Input the PHONES/LINE connector L-channel and R-channel outputs
respectively on channel 1 and channel 2 of the oscilloscope.
* Testing of switch operation is followed by execution of an LED test.
3. On the oscilloscope, set channel 1 to 2 V/div., channel 2 to 2 V/div., and
time to 1 ms/div.
No. Button Darkened LED
1 PHRASE LOOP None 4. Verify that the PHONES/LINE connector L-channel and R-channel output
2 EXIT None values are each 4.2 to 5.0 Vp-p, and that the phase difference between
3 None channel 1 and channel 2 is 90 degrees.
4 None
* Measure the voltage at the flat areas (shown by the arrows in the figure).
5 MENU None fig.DA.eps
6 REVERB LEVEL None
7 REVERB LEVEL PHRASE LOOP (yellow)
8 REVERB LEVEL ON/OFF (green)
9 REVERB LEVEL REC (red)
10 REVERB LEVEL HARMONY (green)
4. Verify that when each button is pressed, the corresponding LED goes
dark and a tactile click sensation is felt at the switch.
* If this procedure is stopped partway through, the switch is faulty. If an LED fails
to go dark, the LED or LED driver circuit is faulty.
16
Nov. 2009 VE-20
4. Verify that the OUTPUT L/MONO connector HOT side and the OUTPUT
R connector HOT side outputs are waveforms like those shown in the
figure below.
* Measure the voltage at the flat areas (shown by the arrows in the figure).
fig.MonoST-1.eps
7. Verify that the OUTPUT L/MONO connector HOT and COLD output
values are each 10 mVp-p or less. 5. Verify that the OUTPUT L/MONO connector HOT side and the OUTPUT
fig.MUTE-2.eps R connector HOT side output values are each 300 to 380 mVp-p.
7. Verify that the OUTPUT L/MONO connector HOT side and the OUTPUT
R connector HOT side outputs are waveforms like those shown in the
figure below.
* Measure the voltage at the flat areas (shown by the arrows in the figure).
fig.MonoST-2.eps
9. Verify that the OUTPUT R connector HOT and COLD output values are
each 10 mVp-p or less.
fig.MUTE-3.eps
8. Verify that the OUTPUT L/MONO connector HOT side and the OUTPUT
R connector HOT side output values are each 300 to 380 mVp-p.
17
Nov. 2009 VE-20
10. Verify that the OUTPUT L/MONO connector HOT side and the OUTPUT
R connector HOT side outputs are waveforms like those shown in the
Clip Check
figure below. 1. Verify that the message CLIP is displayed on the LCD screen.
fig.MonoST-3.eps
2. Connect the signal generator between the 1-2 pins (HOT-GND) of the
INPUT (XLR) connector.
* Connect nothing to the 3 pin (COLD).
3. On the signal generator, set output to 200 Hz and sine wave to 200
mVp-p.
* Adjust so that 200 mVp-p is obtained while the connection is in effect.
AF-AD Check
1. Verify that the message AF-AD is displayed on the LCD screen.
2. Connect the signal generator between the 1-2 pins (HOT-GND) of the
INPUT (XLR) connector.
* Connect nothing to the 3 pin (COLD).
3. On the signal generator, set output to 200 Hz and sine wave to 150
7. Verify that the PHONES/LINE connector L-channel and R-channel output
mVp-p.
values are each 4.7 to 5.3 Vp-p.
* Adjust so that 150 mVp-p is obtained while the connection is in effect.
8. Connect the signal generator between the 1-3 pins (COLD-GND) of the
4. Connect the OUTPUT L/MONO connector HOT and COLD outputs INPUT (XLR) connector.
respectively to channel 1 and channel 2 on the oscilloscope.
* Connect nothing to the 2 pin (HOT).
* This test verifies only the L channel.
9. Adjust so that the input level is 200 mVp-p while the connection is in
5. On the oscilloscope, set channel 1 to 2 mV/div., channel 2 to 2 mV/div., effect.
and time to 1.0 ms/div.
10. Verify that the L-channel and R-channel waveforms of the PHONES/
6. Verify that the OUTPUT L/MONO connector HOT and COLD outputs are LINE connector are like the waveforms shown in the figure below.
waveforms like those shown in the figure below.
* No clipping must be present.
fig.AFAD.eps
fig.clip-2.eps
7. Verify that the OUTPUT L/MONO connector HOT and COLD output
11. Verify that the PHONES/LINE connector L-channel and R-channel output
values are each 15 mVp-p or less.
values are each 4.7 to 5.3 Vp-p.
* In some cases, the waveforms may cancel each other out, resulting in no output
12. Connect the OUTPUT L/MONO connector HOT and COLD outputs
waveforms.
respectively to channel 1 and channel 2 on the oscilloscope.
8. Press [ ] to advance to the next test item.
13. On the oscilloscope, set channel 1 to 200 mV/div., channel 2 to 200 mV/
div., and time to 1.0 ms/div.
18
Nov. 2009 VE-20
14. Verify that the OUTPUT L/MONO connector HOT and COLD outputs are
waveforms like those shown in the figure below.
Residual Noise and Impact-shock
* No clipping must be present. Noise Check
fig.clip-3.eps
1. Verify that the message NOISE is displayed on the LCD screen.
4. Verify that the noise level (DIN audio) is -83 dBu or less.
6. Verify that the noise level (DIN audio) is -95 dBu or less.
8. Verify that the noise level (DIN audio) is -95 dBu or less.
Sine-wave Output
* No testing is required.
The message SIN WAVE appears on the LCD screen and sine waves are
output at the maximum level.
Input/Output Throughput
* No testing is required.
18. Verify that the OUTPUT R connector HOT and COLD outputs are each The message THRU is displayed on the LCD screen, and a signal is sent
350 to 430 mVp-p. through from input to output.
19. Press [ ] to advance to the next test item. 1. Press [ ] to advance to the next test item.
Factory Reset
1. Verify that the message FACTORY RESET? is displayed on the LCD
screen.
* The REC LED flashes.
2. To carry out the factory reset, depress the left pedal. To skip this, press
[ ].
Depressing the left pedal make the REC LED stop flashing and light up
steadily.
When the operation finishes, the message COMPLETED! is displayed on
the LCD screen, followed by END.
2. Verify that no loud noise is heard from the monitor speakers (or
headphones) when the POWER switch is turned on.
3. Verify that no loud noise is heard from the monitor speakers (or
headphones) when the POWER switch is turned off.
19
Nov. 2009 VE-20
20
Nov. 2009 VE-20
fig.b-Jack-2.eps
21
Nov. 2009 VE-20
TP240
6 2 RST-DCDC
IC11 TC7W04FU(TE12L.F)
TC7W04FU(TE12L.F) TC7W04FU(TE12L.F)
IC11 IC11
LED(0:4) XRESET 1 7 3 5
to PANEL_BOAED
TP174
2.7k
2.7k
10k
10k
1 DGND
2 R166 0 LED(4)
3 R111 0 LED(3)
R106
R105
4 3
R37
R47
R104 0 LED(2)
5 R167 0 LED(1) 8 A2 2
6 R170 0 LED(0) VCC A1 1
7 D+3.3
C90 A0
8 0.1uF 5
4 SDA 6
CN1 VSS SCL 7
WP
10uF
IC10
UnPop
DGND 3
8 A2 2
TP97
VCC A1 1
TP34
C33 NC
TP43
TP50
TP103
4 SDA 6
TP108
GND SCL 7
TP111
D+3.3 Q1 DTC114TUAT106 WP
TP112
10uF
C76
IC17
3
HN58W241000FPIE
1 LCD-RESET
R9 10k
R8 100
R6 100
2
DGND R7 100 DGND
L-XLCD-RESET B1 A1 L-XLCD-RESET
L-SCL B2 A2 L-SCL SCL DGND
L-SDA B3 A3 L-SDA SDA
DGND B4 A4 DGND
D+3.3 B5 A5 D+3.3 D+3.3
VOUT B6 A6 VOUT
UnPop
C54
CAP1+ B7 A7 CAP1+
CAP1- B8 A8 CAP1- C106
N-WIRE
1uF 16V
CN3
C93 1
0.47uF 16V DGND 2 X
52610-0877 3
4
5
6
7
8
9
10
D+3.3
CN10 UnPop
10k RTA03-4D103JTP
RTA03-4D103JTP
10k
10k
D+3.3
D+3.3 D+3.3
R92
R90
TP88
TP89
TP49
TP53
TP47
TP68
TP42
TP58
TP61
TP54
10k
R68 1k DGND
1 DGND
1
2
3
4
2
3
4
0.01uF
0.01uF
2
C21
C20
3
4 SW-(0) SW-(0)
5 SW-(1) SW-(1)
6 SW-(2) SW-(2)
7 SW-(3) SW-(3) DGND D+1.5
8 SW-(4) SW-(4)
9 SW-(5) SW-(5)
10 SW-(6) SW-(6)
11 SW-(7) SW-(7)
12 POWER-LED TP239 D+3.3
CN4 D1 UDZS TE-17 5.1B PVCC
WIRING RIBBON 12P/AWG26/P2.0 PVCC
R27 R102 C114
330 TP177
56k
R108
UnPop R2
0
TP59 IC12
BD45431G-TR C113
5 4
DGND R107 VDD VOUT DGND
SUB
TP48 100pF
TP203
TP183
R40 UnPop
R36 UnPop
For Debug
TP90 TP96
DGND XRESET DGND
TP72
MCK
BCK
LRCK
SD-DA
SD-AD
22
Nov. 2009 VE-20
fig.d-Jack-1.eps@R
D+3.3
GND VCC
8
C98 IC11
TC7W04FU(TE12L.F)
0.1uF
4
DGND
D+3.3 D+1.5
C122 TP158
WP-USER 100uF
6.3V
TP175 TP135
C73 0.1uF
TP137
C36 0.1uF
C78 0.1uF
SDA TP176
SCL C61 0.1uF C119
WP-PROG 100uF
C65 0.1uF
6.3V
C75 0.1uF
TP172
C70 0.1uF C67 0.1uF
SDA C77 0.1uF C109 0.1uF
D+3.3
SCL C91 0.1uF C88 0.1uF D+3.3
C44 0.1uF C107 0.1uF
C102 0.1uF C39 0.1uF
1
C103 0.1uF C110 0.1uF 2
3
10k
10k
TP153
TP145
TP147
TP143
TP141
TP230
TP139
TP148
TP149
TP151
TP136
SDA
SCL 4
5
WP-USER R154 UnPop 6
9
17
26
34
49
61
82
96
114
122
132
144
36
41
55
72
101
108
141
R175
XRESET
R172
DGND DGND
RA2 RTA03-4D101JTP WP-PROG R171 0 CN2
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
IVDD
IVDD
IVDD
IVDD
IVDD
IVDD
IVDD
10k
10k
DGND RA5 _CS1/SPICS/P62 RA1 RTA03-4D101JTP
DCK 1 8 102 4 5 100 SW-(4)
DMS 2 7 103 DCK 124 3 6 SW-(5)
DDI 3 6 104 DMS A23/_SYNC/TRS7/P97 125 2 7 SW-(6)
DDO 4 5 105 DDI A22/TRS6/P96 126 1 8
R38
SW-(7) R35
XDRST 106 DDO A21/TRS5/P95 127 LCD-RESET
R4 UnPop _DRST A20/TRS4/P94 128
TP2
A19/TRS3/P93 129 S-EA(6)
84 A18/TRS2/P92 130 XCODEC-PDN S-EA(5)
85 AVDD33 A17/TRS1/P91 131 XCPU-MUTE S-EA(4)
AVREFP A16/TRS0/P90
C121
10uF
S-EA(3)
R169 UnPop
R168 UnPop
95 53 S-EA(2)
94 AGND33 AD15/PWM/P57 54 S-EA(1)
AVREFM AD14/SPICK/P56 56 CPU-PHANTOM
TP238 93 AD13/SPIDI/P55 57
92 AIN7 AD12/SPIDO/P54 58
91 AIN6 AD11/BUCK/P53 59 LED(0:4)
10k
10k
90 AIN5 AD10/BULCK/P52 60
89 AIN4 AD9/BUDO1/P51 63 ESC MODE
8
7
6
5
DGND
88 AIN3 AD8/P50
87 AIN2 43 LED(0) RA22 MODE1
86 AIN1 AD7/P47 44 LED(1)
1
2
3
4
R18
R25
C69 AD1/P41 52
UnPop 133 AD0/P40 DGND
AGND15
64
139 ALE/P67 65
TP168
TP155
TP51
TP80
XIN ST-MONO
2 _CWR/P65 67 WP-PROG
4 _WAIT/P64
140
TP69
TP118
TP110
TP152
TP123
TP133
TP115
TP55
XOUT 120
TP116
TP57
TP165
TP154
TP166
TP76
TP150
TP87
22pF
3
C40
EUDQM
4 5 ELDQM VSS 28
VSS
IC16 RA16
115
123
100
109
138
IC13
10
18
27
35
50
62
83
97
37
42
73
UPD800402GJ-211-UEN-A(ESC) K4S641632N-LC75000
1
DGND
TP122
TP156
TP164
TP128
TP52
TP41
TP101
TP74
TP185
DGND
23
Nov. 2009 VE-20
AVCC
TP232
D ( 0.5% )D ( 0.5% )
AVREF
R12
2.2k
AVCC
TP182
TP138
0.1uF
10uF
R15
2.2k
AVCC
C3
TP13
IC14
D ( 0.5% ) D ( 0.5% )
NJM4580M(TE1) AVREF-XLR
IC14
R58
C58
NJM4580M(TE1)
15k
4
2
1 AGND
3 R3
10uF
AGND GAIN CTRL:L =+20dB
C62 0.1uF
330
16V
GAIN CTRL:H = 0dB
R57
10uF 16V
8.2k
AVCC
C174
C87
TP163
R86
TP11
4.7k
TP134
+48V PVCC AGND AGND D ( 0.5% )
D ( 0.5% )
D ( 0.5% )
0.1uF
TP64
C63
25V
TP85
R88
R85
AVCC
3.9k
3.9k
R101 R91 C156 47pF
TP180
100k 470k D15 C104
TP38
AGND
TP124
TP184
UnPop UnPop 6
UnPop Q10 2SC4117-GR(TE85L.F)
2SA1587-GR(TE85L.F)
2 1 7
2SC4117-GR(TE85L.F) Q11
C2
16V 5
2
IC14
Q32 22uF
D ( 0.5% )
3
1 NJM4580M(TE1)
3
R71 100 C164 AGND C117 TP144 D ( 0.5% TP106
)
R1 1 1
R89
4.7k
R142 68k
3
22uF
C152 47pF
AGND 470k R70
TP258
TP257
TP216
TP215
100 16V
WIRING RIBBON 6P/AWG26/P2.0
2
R48
WIRING RIBBON 6P/AWG26/P2.0
3.3k
C12
D ( 0.5% )
C37 220pF AVREF-XLR
10k
TP63
R16
D ( 0.5% )
D ( 0.5% )
R120
TP214
AVCC
PHANTOM_PWR
0.1uF Q38
820
R125
R124
TP56
4.7k
4.7k
IN-AVREF
FBMA-10-160808-601T
FBMA-10-160808-601T
FBMA-10-160808-601T
AGND
D ( 0.5% ) D ( 0.5% )
AGND AGND 1 2
220pF
TP178
TP99
R51
C16
3.3k
R76
8.2k
16V
3
C59 1000pF TP171 22uF
C162
3/4W TP91
TP205
TP206
TP207
C7 0.1uF
R165 6.8k
100uF 16V
C56 1000pF R74 2SK880-GR(TE85R.F)
JK14 AVCC 100 PVCC
R56
C182
4.7k
R13
1000pF 63V 63V D11
C8
NCJ6FI-V-0 C11
10k
D17
22uF 22uF 220pF D+3.3
TP39
C160 C161
TP3
L1 IN-X-HOT 1 1 2
UnPop AGND
1
R122
L2 IN-X-COLD 2 2 AGND AGND 1SS387(TPH3.F)
10k
R174 10k
1 IN-GND 3 3 AGND
3 L15 4 4
2 C183 IN-P-HOT 5 5 L:+20dB TP146
4 0 IN-P-COLD 6 6 R63
3
H: 0dB
5
6800pF
1M
DTC114TUAT106
C159
CN5 CN6 MIC-GAIN 1
6IN-F-GND AGND
2
Q2
7 TP4 AGND
L11 FBMA-10-160808-601T
L9 FBMA-10-160808-601T DGND
IN BOARD
R131
10k CODEC-VCC
D ( 0.5% )
TP233
TP75
TP179 +-0dB
TP234
TP109
16V
TP181
D ( 0.5% )
R54
C153 10uF
C86 10uF
10
D+3.3 CODEC-VCC 16V R134 10k 2
47pF C172
1
R66 3
D ( 0.5% ) D ( 0.5% )
UnPop
C105
TP100
10k
0.1uF
TP18
R149
100uF
150k
UnPop
C116
6.3V
C141
5
4
TP93 0.1uF 0.1uF AGND
C46
C68
C139
10uF
TP235 AGND
R132
16V
C154
10k
TP92
10uF 16V
VD
VA
D ( 0.5% ) 47pF 16V 2 19
10k LIN LOUT
R137 10uF C92
6 C169 10uF 16V
AGND 7 1 20
5 RIN ROUT
C100
UnPop
17 18 TP236
8
PDN VCOM
TP20
TP159
1uF 50V
0.1uF
R43
0.1uF
L10 12
0
11 CKS3
C5
C6
CDRH4D28NP-680NC-R IC20 10 CKS2
68uH 9 CKS1
C57
NJM2115V(TE1)
4
VSS
CKS0
C147 AGND
C74 1uF
47uF 16V
TP86
TP77
TP22
TP73
TP31
R141
3
TP169
C150
AK4556VT-E2
1M
R62
C35
7
8
6
1M
TP102
TP167
+48V 0.1uF
SW
SW
PUMP
R22 CTRL FB 2
1
100k
0 R39 D18
H:OFF NC APD 16 1SS387(TPH3.F)
2.2uF
2.2uF
2.2uF
TP157
C175 1uF
10 GND
GND
PAD
MON
C135
C134
C136
C166
15pF
D ( 0.5% )
3
TP187
1
R158
CPU-PHANTOM IC21
17
Q16
82k
9
TP70
TP1
R20
1k
R75
R17
4.7k
TP29
R10
TP17
10k
DGND 1
R19
LT3482EUD#TRPBF Q35
10k
D19
2SA1832-GR(T5L.F.T)
3
DTC114TUAT106
TP94
3
DGND
UnPop
1 MUTE P
C131
Mute ON: L
Q17
100
2
UnPop
DTC114TUAT106
XCPU-MUTE 1
UnPop
UnPop
R139
R140
R67
UnPop
C18
C71
1uF
TP78
Q18
2
DGND DGND
TP26
CN20
BATT+ 1 Q33
BATT- 2 DGND 2SA1832-GR(T5L.F.T) MCH6306-TL-E
2SC
POWER
0.5% )
R162 R30 4
G10
33k
D2 5
MINISMDC075F-2 0 ON SW1
0.1uF
2
D20 D1 2
(
C26
G
R163
TP27 1
330k
D ( 0.5% )
JK13 1 3 13 12
3
2 1 1
R157
21
3
1 2 2 2 4 TP95
33k
23 22
UDZS TE-17 11B
3 3 3 BATT+ L13UnPop
SW1 SK22F02 G10 C133 TP84
R121
C47
33k
0.1uF
47uF
R45
C55
R44 25V
0
ADAPTOR BOARD
10
20
0
TP219
TP217
TP218
24
Nov. 2009 VE-20
fig.d-Jack-2.eps@R
R161 18k D ( 0.5% )
XLR OUTPUT Rch R11 18k D ( 0.5% )
Q7
1 2 2SK880-GR(TE85R.F)
TP40
TP126
TP83
3
TP35 C10 TP66
UnPop
TP162
D ( 0.5% ) R ch
R187 18k R59 R118
2 820 680
1 22uF 63V
UnPop
TP62 3 TP30
AVREF C140 C163
C94
IC15
6800pF
TP142
D ( 0.5% ) 22uF 16V
3
TP104
R99
C15
L ch NJM4580M(TE1)
100k
R21 18k
R42
Q5 MUTE 1
10k
Q31
2 1 D ( 0.5% )
4.7k
2SK880-GR(TE85R.F)
R28
2
AVCC
820
3
R136
DTC614TU T106
TP129
TP127
AGND AGND
C155 AGND
D2 1SS387(TPH3.F)
47pF
D5 1SS387(TPH3.F)
D ( 0.5% )
8
TP32
0.1uF
UnPop
C28
NJM4580M(TE1)
C96
5
4
6800pF
NJM4580M(TE1) 22uF 16V
C17
L20 BLM18HD102SN1D
100k
R61
R100
MUTE 1 L19 BLM18HD102SN1D
10k
MICOUT-R-C
MICOUT-R-H
AGND XLR OUTPUT R/MONO
2
Q27 JK1
DTC614TU T106 2
3
AGND AGND AGND 1
1 1 10
2 2 R80 C146 JY-5032
AGND 3 3 0
4 4 0 XLR OUTPUT L/MONO
R183 18k D ( 0.5% ) 5 5 JK2
6 6 2
3
Q12 R33 18k D ( 0.5% ) L7 0 CN7 CN8 1
XLR OUTPUT Lch AGND 10
L3 0
TP244
1 2 L21 BLM18HD102SN1D
MICOUT-L-C
MICOUT-L-H
2SK880-GR(TE85R.F) L16 0 C142 0 JY-5032
TP242
TP119 L18 BLM18HD102SN1D
3
TP249
D ( 0.5% ) L4 0
R41 18k L ch -18.5dB R26 R31 WIRING RIBBON 6P/AWG26/P2.0 OUT BOARD
2 820 22uF 63V 680
1
TP71 TP252 WIRING RIBBON 6P/AWG26/P2.0
UnPop
AVREF 3
C178 C173
TP247
TP246
IC2
6800pF
D ( 0.5% )
C4
22uF 16V
R180
C151
R ch NJM4580M(TE1)
R181
100k
R5 18k Q9 1
MUTE
10k
D ( 0.5% ) Q4
2 1 4.7k
TP113
R46
2SK880-GR(TE85R.F) R178
2
820
TP81
3
TP241
4.7k TP250
D3 1SS387(TPH3.F)
8
C179 0.1uF
IC2 5
AVREF IC2 C177 C167 Att:-13.5dB
6800pF
NJM4580M(TE1)
NJM4580M(TE1) 22uF 16V
3
4
C138
R179
100k
R182
MUTE 1
10k
D ( 0.5% ) D ( 0.5% )
10k 18k
TP37
TP120
TP28
C101 47pF
OUTPUT/PHONES
C181
IC18
TP45
TP82
+9.0dB 33 33
6 R117 R115
AGND 7 2
5 C144 L6
3
NJM4580M(TE1) 100uF FBMA-10-160808-601T
1
3
0.068uF
JK11 HTJ-064-12DSMP
R65
1
C14
MUTE
10k
16V
DTC614TU T106 C53 UnPop
2
TP19
1/4W 1/4W
C95 UnPop
TP79
D+3.3
IC18
TP12
TP117
+9.0dB 33 33 L5
2 R114 R119
R184
FBMA-10-160808-601T
1
10k
R185 10k
AGND 3 C145
MONO:L 100uF Q28
3
0.068uF
R64
NJM4580M(TE1) 1
3
C13
MUTE
10k
STEREO:H 16V
1
ST-MONO
2
Q6 DTC614TU T106
2
IC18 UnPop
NJM4580M(TE1) C19
0.1uF
47uF
C168
0.1uF
0.1uF
0.1uF
16V
C25 UnPop
C45
C30 UnPop
4
UnPop
C49
C64
C38
C24
C42
AGND UnPop
C43
AGND DGND
AGND DGND DGND
PVCC
VCC
D+1.5
D+3.3
TP245
220uF Q36
C126 R153 16V QS5U27TR(PB FREE)
VCC
1000pF 47k
15
16 FB1 C29
TP193
13 INV1 0.1uF
D ( 0.5% ) D ( 0.5% )
D ( 0.5% ) D ( 0.5% )
D+1.5
2
TP197 DTC1 12
3
R143
3.3k
AVCC 0.01uF
2.2k
5 FB2 OUT1
7 INV2 C23 R144
TP198
4
R127 10k 4 8
D ( 0.5% )
D ( 0.5% )
10k D ( 0.5% )
3 2
R78
D ( 0.5% )
19 OUT2 D+3.3
TP199
47k
R160
R77
0.1uF
100uF
STB
6.3V
1
1.5k
18k
1
C22
C80
R146 15k
1000pF
1000pF
R145
TP173
0.1uF
TP8
TP191 SEL1
56
TP200 TP202
R133
2
2
TP196
R49
R50
3
R129
16V
3 RT
C9 0.1uF
1
R151 47k
C176 CT 10 TP189
D ( 0.5% )
R152
C52
27k
27k
14 PGND DGND
D ( 0.5% )
4
C82
C85
100uF R97
47k
SCP
5
R55
22k
C128
GND
FIN
VREF
D ( 0.5% )
C34 0.1uF
C137 470pF
3
C27 0.1uF
220uF
1000pF
1000pF
Q37 TP194
R130 10k
0.1uF
100uF
1
C83
16V
6.3V
C81
D21
C51
C79
20
30
QS5U27TR(PB FREE)
DTC114TUAT106
DGND RST-DCDC DGND
DGND
25
26
10
fig.d-Panel.eps
EN500
C507
UnPop
E-DGND
EVYBAVD0120B
20
P-DGND
Nov. 2009
C506
UnPop
EN500
E-DGND
EVYBAVD0120B
ENC BOARD
3 3 R510 100 1
2 2 R511 100 2
P-DGND
1 1 R512 100 3
SW507 CN504 CN503
SKQKAKD010
D+3.3
WIRING RIBBON 3P/AWG26/P2.0
P-DGND
[PEDAL_R]
C505
0.1uF
WIRING RIBBON 3P/AWG26/P2.0
C503 SW506
SKQKABD010
22uF 16V
UnPop [CONTROL SETTING]
Q500
R506 3 2 UnPop
1
SW504
SKQKABD010
LED508 [MENU}
TP542
TP518
L-34YDSL
2 1 Q506
Yellow R507 3 2 SW502
150 SKQKABD010
1
[PHRASE LOOP] [Cursol->]
DTA114EUAT106 (PB FREE)
LED500
TP514
L-34GDSL
TP537
2 1 Q507 SW503
SKQKAKD010
Green R503 3 2 [PEDAL_L}
1
[ON/OFF] 560
DTA114EUAT106 (PB FREE)
LED509 SW501
L-34HDSL SKQKABD010
TP536
TP513
2 1 Q508 [Cursol<-]
Red R509 3 2
1
[REC] 680
DTA114EUAT106 (PB FREE) SW500
SKQKABD010
LED501
L-34GDSL [PHRASE LOOP]
TP535
TP515
2 1 Q509
Circuit Diagram (Panel, Enc Board)
P-DGND
Green R500 3 2 SW505
1
[CONTROL] 560 SKQKABD010
DTA114EUAT106 (PB FREE)
[REVERB]
TP534
TP516
P-DGND
C502 LED510
22uF 16V L-113GDT
2 1
TP505
P-DGND
TP509 TP532
TP507 Green TP527
TP506 TP522
D+3.3
TP530
P-DGND
C500
TP508 [POWER] TP529
0.1uF
TP510 TP531
TP511 TP528
TP524
C504 TP523
TP525
22uF 16V TP526
P-DGND
ENC_A
P-SW7
P-SW6
P-SW5
P-SW4
P-SW3
P-SW2
P-SW1
P-SW0
ENC_B
PWR_LED
P-DGND
C501
D+3.3
P-DGND
D+3.3
TP533
0.1uF
P-DGND
P-LED0
P-LED1
P-LED2
P-LED3
P-LED4
9
8
7
6
5
4
3
2
1
12
11
10
8
7
6
5
4
3
2
1
2
1
CN502
CN501
to JACK_BOARD CN
CN500
A2001WR2-2P
WIRING RIBBON 12P/AWG26/P2.0