Professional Documents
Culture Documents
FusionDC1000A40 Prefabricated All-in-One Data Center Quick Guide (2021, Zambia, ZESCO)
FusionDC1000A40 Prefabricated All-in-One Data Center Quick Guide (2021, Zambia, ZESCO)
Center
Issue 01
Date 2021-06-18
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees
or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: https://e.huawei.com
Purpose
This document describes the initial configuration parameters of the data center as
well as the precautions, processes, parameters, and drawings for installing the
data center. It helps customers quickly get familiar with product configurations,
and provides installation guidance and technical support for onsite installation
personnel and technical support engineers.
Intended Audience
This document is intended for:
● Maintenance engineers
● Technical support engineers
● System engineers
● Commissioning engineers
● Data configuration engineers
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol Item
Symbol Item
Change History
Changes between document issues are cumulative. The latest document issue
contains all updates made in previous issues.
Issue 01 (2021-06-18)
This issue is the first official release.
Contents
This chapter describes the notes for using the quick guide.
● Before the installation, check whether the materials are intact according to
the packing list. If there is any problem, contact Huawei technical support.
● This document provides only the initial configuration parameters required for
data center commissioning and O&M as well as the drawings and parameters
required for onsite installation.
● Before using this document, read through and keep in mind the safety
precautions and the cautions and notes for operations.
● Precautions provided in this document are only supplementary to the local
laws and regulations governing the data center.
● The system configuration parameters are essential to reliable running of the
system. Improper modifications of parameters may easily cause abnormal
running status, or even damage to the system. You are not allowed to modify
configuration parameters without permission when using the data center. If a
modification is necessary, contact Huawei technical support. Huawei shall not
be responsible for any loss caused by unauthorized configuration
modification.
● You can modify initial configurations under the guidance of Huawei
engineers. Huawei assumes no liability for any loss caused by unauthorized
changes to the initial configurations.
● Some parameters mentioned in this document should be provided and
configured by onsite technical support engineers based on the actual
application of the data center.
● If parameters need to be modified during the running of systems, the
operator should be a professional in this field and familiar with each system
and its working principles.
● Before performing an operation, ensure that the prerequisites are met.
Otherwise, the expected result may not be achieved. More seriously,
equipment damage and personal injury may occur.
● Put on necessary protective equipment such as the safety helmet and gloves
before entering the site.
● A data center can be powered on for commissioning only after it has been
installed and passed the installation check.
2 Installation Drawings
Grounding Pre-fab. Modules Grounding Pre-fab. Modules NO.S002 Pre-fab. Module Grounding Position Diagram
Installing External Accessories Installing Eaves Installing Eaves NO.S003 Eave Installation Position Diagram
Outlet Positions of Electric Cables and ELV Signal Electric Cable and ELV Signal Cable Outlet Position
Connecting Cables Installing Electric Cables and ELV Signal Cables NO.S004
Cables Diagram
Installing Air Conditioners and LCD Embedded Air Conditioner and LCD Embedded Piece
Installing Civil Air Conditioners Installing Air Conditioners and LCD Embedded Pieces NO.S005
Pieces Installation Position Diagram
Installing Suspended Ceiling-Aluminum Clip-in Suspended Ceiling-Aluminum Clip-in Panel
Installing Suspended Ceilings Installing Suspended Ceiling-Aluminum Clip-in Panels NO.S006
Panels Installation Position Diagram
Installing Glass Windows Installing Glass Windows Installing Glass Windows NO.S007 Glass Window Installation Position Diagram
1,856.9
\
\
2,708
>=\
12,192
3,902.2 12,414
>=\
400
340
260
290
370
430
8-∅
24
Single-capacity base
Steel base
Concrete platform
\
\
Ground
Concrete platform
Note:
1. The concrete platform needs to support a pre-fab. module with the maximum weight of 25,000 kg. The
recommended anti-seismic acceleration is 3g. Calculate the strength of the concrete platform based on
the contact area (refer to the 1720 cm² area of a single-capacity base installed on the ground). Take an
engineering margin into consideration.
2. Each base has eight mounting holes. Only four holes need to be used, preferably the outer four holes. If Item Drawing No. Quantity Unit
an outer hole is on the top of groundwork reinforcing steel bars, select the inner hole instead. Single-capacity
base
DKBA40703508 4 PCS
3. During installation, ensure that the direction of the single-capacity base is the same as the drawing. T-shaped bolt DKBA80473086 4 PCS
4. Reserve two cable outlets for power cables at the shown positions on the ground. It is recommended Expansion bolt
DKBA04802828_M16×
150_S 16 PCS
that the cable outlets be made of steel pipes or PVC pipes with an inner diameter of not less than Ø100
mm and a reserved height of 500 mm aboveground.
No.S002 Pre-fab. Module Grounding Position Diagram
540
540
540
540
93
540
176.7
1,026
176.7
1,026
Note:
1. Four ground points are set for each pre-fab. module, among which two are located
at the front wall and two at the rear wall. For details about the ground points, see the
Item Drawing No. Quantity Unit
figure above. The ground points are connected with the ground grid. Before Ground GB5783-2000_M12X30_S_ZNALL 4 PCS
grounding, remove the aluminum foil from the ground points. The ground bolts are screw
Eave 1 Eave 2
Eave
component
Rubber strip
GB5783-2000_M16X40_S_ZNAL
280
1,200 drainage port
280
88.9
2,518
2,410
2,298
1,898
548
Floor inside the pre-fab. module Floor inside the pre-fab. module
600
11400
156
Hanging rod
Indoor Outdoor
Neutral black sealant
Glazing bead
Corner connector
30
Frame
Wall
M8*80 nylon expansion
bolt
After all windows are installed, install the glass bead and apply the glass cement.
The glass window packaging components include all the materials.
Item Drawing No. Quantity Unit
Glass
YT63217433(1mX1m) 2 PCS
window
No.M003 Monitoring Onsite Wiring Diagram
A/C A/C
Window
A/C A/C
No.P003 Mains Input Power Cable Wiring Diagram
A/C A/C
C1 C2
Window
Socket-2 Socket-3 Socket-4 Socket-5 Socket-6 Socket-7 Socket-8 Socket-9 Socket-10 Socket-11 Lighting PDB-1 Lighting PDB-2
Socket-14(Air Conditioner)
WY-10A WY-10A WY-10A WY-10A WY-10A WY-10A WY-10A WY-10A WY-10A WY-10A
Socket-1(Air Conditioner)
WY-10A
A/C A/C
WY-10A
WY-10A
Socket-13
1
Fan Switch-1
Socket-12 1
WY-10A
Lighting Switch-1
Fan-2
Fan-3
Fan-1
1000mm*1000mm
INPUT OUTPUT
Cable No. Breaker Power System Huawei Part Description Terminal Spec From Part 1 Terminal Spec From Part 2
Container From Device Container To Device
Initial Configurations for the Cooling System (Air Cooled) NO.C001 Cooling Device Layout Diagram N/A
Initial Configurations for the Management System NO.M001 Monitoring Device Layout Diagram N/A
Initial Configurations for the Fire Extinguishing System NO.F001 Fire Extinguishing Device Layout Diagram (CE) N/A
A/C A/C
Socket-2 Socket-3 Socket-4 Socket-5 Socket-6 Socket-7 Socket-8 Socket-9 Socket-10 Socket-11 Lighting PDB-1 Lighting PDB-2
WY-10A WY-10A WY-10A WY-10A WY-10A WY-10A WY-10A WY-10A WY-10A WY-10A
Socket-14(Air Conditioner)
Lighting-1 Lighting-3 Lighting-5 Lighting-7 Lighting-9 Lighting-11
1000mm*1000mm
Socket-1(Air Conditioner)
WY-10A
A/C A/C
WY-10A
WY-10A
Socket-13
1
Fan Switch-1
Socket-12 1
WY-10A
Lighting Switch-1
Fan-1
Fan-2
Fan-3
1000mm*1000mm
Socket
1
Lighting Switch
1
Fan Switch
Lighting
10A/1P MCB+YO+AUX
QF9
Spare
QF8
10A/1P MCB
Spare
QF7
10A/1P MCB
Socket-10/11
No.P002 Power Supply and Distribution System Diagram
QF6
10A/1P MCB
Socket-8/9
QF5
10A/1P MCB
Socket-6/7
32A/1P RCD
QF4
10A/1P MCB
Customer Input
Socket-4/5
QF3
10A/1P MCB
QF
Socket-2/3
QF2
16A/1P MCB
Lighting PDB-2
Socket-13
QF1
16A/1P MCB
Socket-12
10A/1P MCB+YO+AUX
QF9
Fan Switch-1
QF8
10A/1P MCB
Spare
QF7
10A/1P MCB
Spare
QF6
10A/1P MCB
Spare
QF5
10A/1P MCB
Exit-1
32A/1P RCD
QF4
10A/1P MCB
Customer Input
Emergency Lighting-1/2
QF3
10A/1P MCB
QF
Lighting Switch-1 Lighting-1~14
QF2
16A/1P MCB
Lighting PDB-1
Socket-14(Air Conditioner)
QF1
16A/1P MCB
Socket-1(Air Conditioner)
No.C001 Cooling Device Layout Diagram
A/C A/C
A/C A/C
Fan-1
Fan-2
Fan-3
1000mm*1000mm
No.M001 Monitoring Device Layout Diagram
A/C A/C
Window
A/C A/C
No.F001 Fire Extinguishing Device Layout Diagram (CE)
A/C A/C
A/C A/C
Exit-1
Emergency Lighting-1 Emergency Lighting-2
Emergency Lighting EXIT Emergency Lighting
No.F003 Emergency Exit Diagram
A/C A/C
A/C A/C
FusionDC1000A40 Prefabricated All-in-One Data
Center
Quick Guide (2021, Zambia, ZESCO) A Common Torque Selection Table
NOTE
This table lists only the recommended torque for common screws, bolts, and pipe
connectors. The torques you choose should meet project requirements.
M3 Cross Electric 6 \ 6 \
recessed screwdriv
small er
pan head
screw
assembly
M4 Cross Electric 12 12 14 \
recessed screwdriv
counters er
unk head
screw;
cross
recessed
pan head
screw
assembly
M5 Cross Electric 30 \ \ \
recessed screwdriv
pan head er
thread
forming
screw
M5 Cross Pneumati 50 \ \ \
recessed c
counters screwdriv
unk head er
wood
screw
M6 Cross Pneumati 30 50 30 50
recessed c
hexagon screwdriv
head er/
screw Electric
assembly screwdriv
er
Cross Pneumati 80 \ \ \
recessed c
counters screwdriv
unk head er
screw