Professional Documents
Culture Documents
AIDITE AMD-500 Fault Code and Troubleshooting
AIDITE AMD-500 Fault Code and Troubleshooting
AIDITE AMD-500 Fault Code and Troubleshooting
复位系统,手动模式下手
动正方向移动 Z 轴,松开
刀具前端露出长度
没有外部气压输
入,机器强制停止
没有外部气压,机器强制
工作,保护风冷主 检查空压机或者气压管路
停止运行 Without
A1002 轴 Without external 是否异常 Check whether the
external air pressure, the
air pressure input, air compressor or air
machine is forced to stop
the machine is pressure pipeline is abnormal
running
forced to stop
working to protect
the air-cooled
spindle
A1003
主轴变频器报警 Spindle 主轴变频器故障 关闭机器,20 秒重新开
清除,则打开后盖,查看
变频器故障代码 拍照并发
开启对刀仪时对刀仪处
对刀仪信号故障
于触发状态 The tool 更换对刀仪 Replace the tool
A1004
Tool setter signal
setter is in the trigger state setter
failure
when the tool setter is
turned on
外部气压输入压力 检查空压机或者气压管路
外部气压压力不足
A1005 不足 Insufficient 是否异常 Check whether the
Insufficient external air
pressure external air input air compressor or air
pressure pressure pipeline is abnormal
A3413
对刀中检测到刀号非法 刀库异常 Tool 重置刀库 Reset the tool
对刀点 Z 加[最长刀长]
加[安全距离]超出了 Z
XYZ 轴未回零,不能进行
主轴当前刀号与指定的
测量刀号不一致 The
刀库异常 Tool 重置刀库 Reset the tool
A3569
current tool number of the
magazine abnormal magazine
spindle is inconsistent
with the specified
measurement tool number
A3570
刀长连续测量误差过大, 对刀仪需要清洗或 检测对刀仪 Detect tool
setter
可能对刀仪有脏污 The 者故障 The tool
continuous measurement
error of the knife length is setter needs cleaning
too large, and the tool or malfunction
setter may be dirty
快速移动时触碰到了对
刀仪,可能被测量的刀长
刀具露出长度过长
大于[最长刀长]The tool
检查刀长 Check the length
A3571 The exposed length
setting instrument was
of the tool is too of the knife
touched during rapid
long
movement, and the
measured tool length may
be greater than [longest
tool length]
慢速探测前已触碰到了
对刀仪,可能[回退量]太
Broken or broken
值的差值超出范围,可能
tool
已磨损或断刀 The
difference between the
measured tool length
value and the system tool
length value is out of
range, and the tool may
be worn or broken
没有感应到探测信号,可
能已断刀或者对刀器信
刀具破损或者断刀
A3575 更换刀具 Change tool
号无效 No detection Broken or broken
tool
signal is sensed, the tool
may be broken or the tool
setter signal is invalid
长补偿表的值与断刀检
测值偏差较大,请更新断
magazine abnormal
失败 The empty knife 刀具是否异常 Reset the tool
指令刀号不在范围 T0~
输入错误的换刀指
检查输入的换刀指令 Check
T6Command tool number
A3579
令 Input wrong tool the input tool change
is not in the range T0~
command
change command
T6
当前刀号不在范围 T0~
当前刀号错误
T6The current tool 重置刀库 Reset the tool
A3580
number is not in the range Current tool number
magazine
error
T0~T6
A*****
伺服报警 Servo alarm 伺服驱动器报警 自动模式下,复位机器,
则关闭机器,20 秒重新开
机,报警会自动清除。重
新开机后,如果报警扔没
有清除,拍下界面上的伺
服报警代码内容,并发送