Professional Documents
Culture Documents
ALFA-17 - Rock Mechanics
ALFA-17 - Rock Mechanics
ROCK MECHANICS
ROCK MECHANICS
ROCK MECHANICS
INDEX ROCK MECHANICS
ROCK MECHANICS
TECHNICAL SPECIFICATIONS
Point Load with Load Cell and Digital Readout Unit (RM-120/LC)
ROCK MECHANICS
TECHNICAL SPECIFICATIONS
ROCK MECHANICS
TECHNICAL SPECIFICATIONS
▪▪ Supplied with a water pump for cooling the materials while cutting.
TECHNICAL SPECIFICATIONS
ROCK MECHANICS
▪▪ The core that is going to be tested is placed horizontally and the impact
is applied on it.
SUPPLIED WITH
• Carrying Case
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
▪▪ Easy to clean
TECHNICAL SPECIFICATIONS
▪▪ Used to shred medium-hard minerals, ores, coal, coke, hard plastic, wood, paper, tires and brittle materials
▪▪ Heavy-Duty constuction
TECHNICAL SPECIFICATIONS
▪▪ Used under rough conditions for grinding of hard, medium-hard, brittle and tough materials
▪▪ Required few minutes to achieve the desired grind size, and work continuously
▪▪ Application examples: minerals, ores, bauxite, clinkers, chalk, chamotte, concrete,
construction materials, soil samples, gypsum … etc.
TECHNICAL SPECIFICATIONS
▪▪ Used under rough conditions for grinding of hard, medium-hard, brittle and tough materials
▪▪ Required few minutes to achieve the desired grind size, and work continuously
▪▪ Application examples: minerals, ores, bauxite, clinkers, chalk, chamotte, concrete,
construction materials, soil samples, gypsum … etc.
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
planetary mixing
TECHNICAL SPECIFICATIONS
SUPPLIED WITH
• Cutting Blade
B-062/S B-062/M
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
SIEVE (B-040)
ISO 3310:1 • ASTM E11• BS 410
▪▪ All Sieves are made of stainless steel woven wire and frame that meet international specifications.
▪▪ The sieve aperture is clearly marked on the metallic label.
▪▪ Our sieves are of the highest quality to ensure consistent fit, accurate, specifications and durable construction.
▪▪ The sieves are available in two diameters (200 mm) and (300 mm).
▪▪ Cover and pan should be ordered separately.
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
▪▪ Stirrer can be infitely variable between 50 – 2600 rpm, supplied with digital
indicator for speed
▪▪ Mechanism to lower/lift the stirring head
▪▪ Flotation cells are made of stainless steel with capacities 1, 2, 3 and 4 liters
▪▪ The base and support column are made of cast aluminum
TECHNICAL SPECIFICATIONS
▪▪ Supplied with air pressure regulator, gauge, valve and filter pack
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
▪▪ LCD indicator:
▪▪ Calibration function (password-protected)
▪▪ Maximum load and time are set
▪▪ Overload protection
▪▪ Application examples:
▪▪ Cement, gypsum, ores, raw materials, slag … etc.
TECHNICAL SPECIFICATIONS
▪▪ 220 - 240 V / 50 - 60 Hz
TECHNICAL SPECIFICATIONS
▪▪ 220 - 240 V / 50 - 60 Hz
▪▪ Three dech grading machine with each deck 1000 x 2000 mm size
▪▪ Used to determine the resistance to breakage after dropping the sample with
specified conditions mentioned in standards
▪▪ The box has a lifting mechanism by pulleys and 2 door hinged lengthwise with a latch
for rapid opening
▪▪ Rigid base plate with 4 sides preventing loss of coke
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
▪▪ Used to determine the resistance to abrasion and crumbing of the iron ores,
such as pellet and sinter form
▪▪ The drum rotates 200 revolutions with 15 kg of sample
▪▪ Supplied with 2 test sieves
▪▪ Collector at the bottom to collect shredded materials
TECHNICAL SPECIFICATIONS
▪▪ 220 - 240 V / 50 - 60 Hz
TENSILE TESTING
▪▪ Available models:
▪▪ 300 kN (30 tons)
▪▪ 600 kN (60 tons)
▪▪ 1000 kN (100 tons)
▪▪ 2000 kN (200 tons)
COMPRESSION TESTING
TECHNICAL SPECIFICATIONS
once opened
TECHNICAL SPECIFICATIONS
• Capacity: 1000 kN
• 380 V (3 phase)
▪▪ Drilling
▪▪ Polishing
▪▪ Cutting
operator
TECHNICAL SPECIFICATIONS
▪▪ Drilling
▪▪ Polishing
▪▪ Cutting
▪▪ Ingot is placed on the support system and all the a/m functions are done automatically in a short time by an operator