Professional Documents
Culture Documents
HPS SineWave Motor Protection Filter Brochure
HPS SineWave Motor Protection Filter Brochure
• Voltage Reflection
• Harmonic Distortion
• Bearing Current (that can lead to failure) Increased System Efficiency
• Insulation Stress
• Motor Noise Level
Applications
Designed for applications with long cables up to 15,000 feet (4570 meters) between the VFD and the motor. Typical applications include:
Environmental Conditions
Open Style: Up to 50°C
Ambient Operating Temperature:
Enclosed Style: Up to 40°C
Altitude: Up to 1000m (about 3280.84 ft)
Cooling Method: Natural Convection
Enclosure Style: Open Style or Type 3R
Performance
The design of the HPS Centurion S Sinewave filter employs an LC topology, delivering superior performance and high attenuation across a
broader frequency range, all while maintaining a low Total Harmonic Distortion of voltage (THDv) value.
HPS Centurion S is integrated into a wide range of HPS Power Quality products including dV/dT Filters, Line Reactors, and Passive
Harmonic Filters.
1000 1000
500 500
Volts (V)
Volts (V)
0 0
-500 -500
-1000 -1000
-1500 -1500
0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 30 35 40
Time (ms) Time (ms)
88
Voltage THD (%)
Motor Voltage THD (%)
77
66
55
44
Motor
33
22
11
00
20
20 30
30 40
40 50
50 60
60 70
70 80
80 90
90 100
100 110
110
Load
Load (%)
(%)
A SineWave filter effectively filters out high-frequency components, mitigating both common mode and differential mode noise. The
result is enhanced protection for the motor and feeder cable insulation systems as well as reduced wear on the motor bearings.
Example 1.
Example 2.
Motors
The SineWave filter in this installation will increase transformer efficiency and lower the transformer's operating temperature. Additionally,
the filter reduces voltage spikes that can overstress the winding insulation of the transformer.
Utility Grid Transformer VFD SineWave Filter Transformer Long Cable Motor
C S 1 K 0 0 2 5 F
500A 0500
Selection Guide
HPS Centurion S SineWave motor protection filters are designed to provide a sine wave output voltage when driven from PWM inverters
with switching frequencies between 2 kHz and 8 kHz. These filters offer solutions for variable frequency applications, safeguarding the
motor and feeder cables, prolonging its lifespan, enhancing its efficiency, and enabling it to operate at a lower temperature. The filter will
also eliminate the high dV/dT and reflected waves associated with the PWM inverter output waveform.
Select the filter based on Full Load Amps (FLA) of the motor.
600V
Motor Filter Capacitor
Encl. Filter Reactor Dimensions in Inches [mm] Dimensions in Inches
Rating at Filter
Catalog Style [mm]1 Capacitor Weight Watts
600VV Current
Number (F-Floor, Qty2 Lbs. [kg] Loss
(HP) - Ref. (A) Dimens.
W-Wall) Width Depth Height H D
ONLY Fig.
Open (F) 7.12 [181]] 4.70 [119] 6.35 [162]
CS1P0007F 1 6.5 [165] 2.6 [66] 1 16 [7]
5 7 Open (W) 7.50 [190] 5.60 [142] 8.42 [214] 94
CS1P0007C Type 3R CN1-1 16.9 [480] 14.0 [356] 17.6 [448] Pre-Installed in Enclosure 60 [27]
Open (F) 7.12 [181]] 4.70 [119] 6.35 [162]
CS1P0009F 1 7.5 [191] 3.5 [89] 1 17 [8]
7.5 9 Open (W) 7.50 [190] 5.60 [142] 8.42 [214] 95
CS1P0009C Type 3R CN1-1 16.9 [480] 14.0 [356] 17.6 [448] Pre-Installed in Enclosure 60 [27]
Open (F) 7.12 [181] 4.70 [119] 6.35 [162]
CS1P0012F 1 7.5 [191] 3.5 [89] 1 19 [9]
10 12 Open (W) 7.50 [190] 5.60 [142] 8.42 [214] 102
CS1P0012C Type 3R CN1-1 16.9 [480] 14.0 [356] 17.6 [448] Pre-Installed in Enclosure 65 [29]
Open (F) 9.25 [235] 5.50 [140] 7.50 [191]
CS1P0018F 1 9.2 [235] 3.5 [89] 1 31 [14]
15 18 Open (W) 9.25 [235] 6.00 [152] 9.60 [244] 165
CS1P0018C Type 3R DH1 21.5 [546] 20.1 [510] 22.0 [559] Pre-Installed in Enclosure 85 [39]
Open (F) 9.25 [235] 6.00 [152] 7.50 [191]
CS1P0023F 1 11.8 [301] 3.5 [89] 1 31 [14]
20 23 Open (W) 9.25 [235] 6.50 [165] 9.60 [244] 175
CS1P0023C Type 3R DH1 21.5 [546] 20.1 [510] 22.0 [559] Pre-Installed in Enclosure 85 [39]
Open (F) 9.25 [235] 6.50 [165] 7.50 [191]
CS1P0027F 1 11.8 [301] 3.5 [89] 1 41 [19]
25 27 Open (W) 9.25 [235] 6.80 [173] 9.60 [244] 200
CS1P0027C Type 3R DH1 21.5 [546] 20.1 [510] 22.0 [559] Pre-Installed in Enclosure 100 [45]
Open (F) 9.25 [235] 6.50 [165] 7.50 [191]
CS1P0035F 1 11.8 [301] 3.5 [89] 1 46 [21]
30 35 Open (W) 9.25 [235] 7.00 [178] 9.60 [244] 220
CS1P0035C Type 3R DH1 21.5 [546] 20.1 [510] 22.0 [559] Pre-Installed in Enclosure 105 [48]
Open (F) 10.6 [269] 8.30 [211] 10.0 [254]
CS1P0045F 2 11.8 [301] 3.5 [89] 1 60 [27]
40 45 Open (W) 11.5 [292] 8.80 [224] 12.0 [305] 330
CS1P0045C Type 3R DH1 21.5 [546] 20.1 [510] 22.0 [559] Pre-Installed in Enclosure 115 [52]
*Weight & dimensions are approximate
1
Capacitors are supplied individually for open-style designs and come pre-installed within enclosed designs
2
Please refer to figure G for capacitor drawing
CS1P0250F Open (F) 2 14.5 [368] 9.90 [251] 18.5 [470] 8.9 [226] 5.4 [137] 3 260 [118]
250 250 975
CS1P0250C Type 3R DH3 28.3 [719] 27.0 [687] 36.0 [914] Pre-Installed in Enclosure 400 [181]
CS1P0305F Open (F) 2 15.0 [381] 11.0 [279] 18.5 [470] 10.4 [265] 5.4 [137] 3 300 [136]
300 305 1080
CS1P0305C Type 3R DH3 28.3 [719] 27.0 [687] 36.0 [914] Pre-Installed in Enclosure 450 [204]
CS1P0362F Open (F) 3 21.0 [534] 15.0 [381] 20.0 [508] 8.9 [226] 5.4 [ 137] 4 370 [168]
350 362 1390
CS1P0362C Type 3R DH4 31.5 [800] 29.5 [749] 44.5 [1130] Pre-Installed in Enclosure 550 [249]
CS1P0415F Open (F) 3 22.0 [559] 15.0 [381] 21.0 [533] 10.4 [265] 5.4 [137] 4 400 [181]
400 415 1460
CS1P0415C Type 3R DH4 31.5 [800] 29.5 [749] 44.5 [1130] Pre-Installed in Enclosure 580 [263]
CS1P0450F Open (F) 3 22.0 [559] 16.0 [406] 22.0 [559] 10.4 [265] 5.4 [137] 5 415 [188]
450 450 1480
CS1P0450C Type 3R DH4 31.5 [800] 29.5 [749] 44.5 [1130] Pre-Installed in Enclosure 600 [272]
CS1P0500F Open (F) 3 23.0 [584] 17.0 [432] 22.0 [559] 14.8 [376] 3.5 [89] 7 530 [240]
500 500 1520
CS1P0500C Type 3R DH4 31.5 [800] 29.5 [749] 44.5 [1130] Pre-Installed in Enclosure 730 [331]
Figure #1 Figure #2
→
→
H
H
→
→
→
→ →
W D
W D
→
→
→
→ →
Figure #3
→
H
→
→
D
→
W
→ →
CAPACITOR
MOUNTING NUT
HPS SUPPLIED
MTG BRACKET
.44
1.50
2.25 .50
480V 600V
Open Style Floor (Mounting Open Style Floor (Mounting
Current Dimensions) Current Dimensions)
Dimensional Dimensional
Ratings (A) Ratings (A)
Figure MTG MTG Figure
@ 480V MTG SLOT @ 600V MTG MTG
WIDTH DEPTH MTG SLOT
WIDTH DEPTH
9 to 12 4.80 [122] 3.27 [83] 0.38 [10] x 0.50 [13] 7 to 12 4.80 [122] 3.27 [83] 0.38 [10] x 0.50 [13]
16 4.80 [122] 3.77 [96] 0.38 [10] x 0.50 [13] 18 to 23 1 6.00 [152] 3.96 [100] 0.44 [11] x 1.00 [25]
22 6.00 [152] 3.20 [81] 0.38 [10] x 0.50 [13] 27 to 35 6.00 [152] 4.5 [115] 0.44 [11] x 1.00 [25]
1
27 6.00 [152] 3.70 [94] 0.44 [11] x 1.00 [25] 45 7.20 [183] 4.97 [126] 0.44 [11] x 1.00 [25]
35 6.00 [152] 4.20 [107] 0.44 [11] x 1.00 [25] 55 7.50 [190] 5.93 [151] 0.44 [11] x 1.00 [25]
45 7.20 [183] 4.53 [115] 0.44 [11] x 1.00 [25] 65 7.50 [190] 6.18 [157] 0.44 [11] x 1.00 [25]
55 7.20 [183] 6.33 [161] 0.44 [11] x 1.00 [25] 80 8.00 [203] 6.18 [157] 0.44 [11] x 1.00 [25]
65 7.50 [190] 5.43 [138] 0.44 [11] x 1.00 [25] 110 to 130 2 8.00 [203] 6.43 [163] 0.44 [11] x 1.00 [25]
80 8.00 [203] 0.44 [11] x 1.00 [25] 160 9.00 [229] 7.68 [195] 0.44 [11] x 1.00 [25]
110 8.00 [203] 0.44 [11] x 1.00 [25] 200 9.00 [229] 8.81 [224] 0.44 [11] x 1.00 [25]
130 8.00 [203] 6.17 [157] 0.44 [11] x 1.00 [25] 250 9.50 [241] 7.17[182] 0.44 [11] x 1.00 [25]
2
160 8.00 [203] 6.67 [169] 0.44 [11] x 1.00 [25] 305 10.0 [254] 7.68 [195] 0.44 [11] x 1.00 [25]
200 9.00 [229] 7.67 [195] 0.44 [11] x 1.00 [25] 362 7.00 [178] 10.0 [254] 0.44 [11] x 0.75 [19]
250 9.50 [241] 6.42[163] 0.44 [11] x 1.00 [25] 415 7.00 [178] 10.5 [267] 0.44 [11] x 0.75 [19]
3
305 9.50 [241] 7.17[182] 0.44 [11] x 1.00 [25] 450 7.25 [184] 10.5 [267] 0.44 [11] x 0.75 [19]
362 10.0 [254] 8.17[208] 0.44 [11] x 1.00 [25] 500 7.50 [191] 11.2 [286] 0.44 [11] x 0.75 [19]
415 7.00 [178] 9.00 [229] 0.44 [11] x 0.75 [19]
480 to 515 3 7.75 [197] 9.50 [241] 0.44 [11] x 0.75 [19]
600 7.75 [197] 11.0 [279] 0.44 [11] x 0.75 [19]
480V
Dimensions in Inches [mm]
Current Ratings (A) Dimensional
@ 480V Figure
MTG WIDTH BOT MTG WIDTH TOP MTG HGT MTG SLOT
9 to 16 6.13 [156] 2.75 [70] 6.80 [173] 0.44 [11] x 0 .75 [19]
22 to 35 1 6.13 [156] 2.75 [70] 8.00 [203] 0.44 [11] x 0 .75 [19]
45 10.20 [259] 4.50 [114] 10.10 [257] 0.44 [11] x 0 .75 [19]
55 10.20 [259] 4.50 [114] 10.10 [257] 0.44 [11] x 0 .75 [19]
65 to 160 10.20 [259] 4.50 [114] 14.50 [368] 0.44 [11] x 0 .75 [19]
2
200 11.44 [291] 4.50 [114] 14.50 [368] 0.44 [11] x 0 .75 [19]
250 11.44 [291] 4.50 [114] 14.50 [368] 0.44 [11] x 0 .75 [19]
600V
Dimensions in Inches [mm]
Current Ratings (A) Dimensional
@ 600V Figure
MTG WIDTH BOT MTG WIDTH TOP MTG HGT MTG SLOT
7 to 12 6.13 [156] 2.75 [70] 6.80 [173] 0.44 [11] x 0 .75 [19]
1
18 to 35 6.13 [156] 2.75 [70] 8.00 [203] 0.44 [11] x 0 .75 [19]
45 10.20 [259] 4.50 [114] 10.10 [257] 0.44 [11] x 0 .75 [19]
2
55 to 200 10.20 [259] 4.50 [114] 14.50 [368] 0.44 [11] x 0 .75 [19]
WA* WB*
WA1* B
A1 B1
0.56 (4)
D
BACK
C
WF* K
E
WE*
MA F MB 0.56 (4)
A
A
MA B
A1 B1
0.50 H
Keyhole
Slot (4) H
D
C K
F
BACK
MA L MB 0.63 (4)
FRONT VIEW All Dimensions in Inches SIDE VIEW
A B
B1
BACK
C K
E
2.00
MA MB
.63 (4)
M
FRONT VIEW All Dimensions in Inches SIDE VIEW
Termination Details
5 18 - 14 AWG 18 - 14 AWG
7.5 18 - 14 AWG 18 - 14 AWG
10 13 - 10 AWG 13 - 10 AWG
15 14 - 8 AWG 14 - 8 AWG
20 14 - 8 AWG 14 - 8 AWG
25 Dia. 1A Dia. 1A
30 Dia. 1A Dia. 1A
40 Dia. 1A Dia. 1A
50 Dia. 1A Dia. 1A
60 Dia. 1A Dia. 1A
75 Dia. 1B Dia. 1A
100 Dia. 1B Dia. 1B 1A = 0.28” Dia.
1B = 0.44” Dia.
125 Dia. 1B Dia. 1B 1C = 0.56” Dia.
150 Dia. 1B Dia. 1B
200 Dia. 1B Dia. 1B
350 Dia. 1B Dia. 1B DIAGRAM 1
300 Dia. 1B Dia. 1B
350 Dia. 1B Dia. 1B
400 Dia. 1C Dia. 1B
450 Dia. 1C Dia. 1B
500 Dia. 1C Dia. 1C
Other HPS Power Quality Products
HPS has many power quality products which mitigate current and voltage harmonics caused by non-linear loads including rectifiers,
variable frequency drives, DC power supplies and E.V. charging.
UNITED STATES
Hammond Power Solutions
1100 Lake Street
Baraboo, Wisconsin 53913-2866
Tel: (608) 356-3921 | Fax: (608) 355-7623
Toll Free: 1-866-705-4684
UNITED STATES
sales@hammondpowersolutions.com
MEXICO
Hammond Power Solutions Latin America S.
Av. No. 800,
Parque Industrial Guadalupe
Guadalupe, NL, Mexico, C.P. 67190.
Tel: (819) 690-8000
MEXICO
sales@hammondpowersolutions.com
ASIA
Hammond Power Solutions Pvt. Ltd.
Plot No 6A, Phase -1, IDA,
Pashamylaram, Patancheru (M)
Sangareddy, 502 307, India
Tel: +91-994-995-0009
ASIA
marketing-india@hammondpowersolutions.com
sales-emea@hammondpowersolutions.com
hammondpowersolutions.com CENTSP-BBH2-EN
December 2023