Professional Documents
Culture Documents
Manual de Instalacao RFEye
Manual de Instalacao RFEye
Mounting Kit
User Guide
Legal Information
Copyright © 2014 CRFS Limited
The copyright of this document is the property of CRFS Limited. Without the written
consent of CRFS, given by contract or otherwise, this document must not be copied,
reprinted or reproduced in any material form, either wholly or in part, and the
contents of this document, or any methods or techniques available therefrom, must
not be disclosed to any other person whatsoever.
CRFS Limited reserves the right to make changes to the specifications of the products
detailed in this document at any time without notice and obligation to notify any
person of such changes.
RFeye, CRFS and the CRFS logo are trademarks of CRFS Limited. All other trademarks
are acknowledged and observed. Mention of third-party products does not constitute
an endorsement or a recommendation.
All figures, data and specifications contained in this document are typical and must be
specifically confirmed in writing by CRFS Limited before they apply to any tender,
order or contract. CRFS takes every precaution to ensure that all information
contained in this publication is factually correct but accepts no liability for any error or
omission. No freedom to use patents or other property rights is implied by this
document.
Disclaimer
The information contained in this document is not intended to amount to advice on
which reliance should be placed. Although we take reasonable steps to ensure the
accuracy of the information provided, we provide it without any guarantees,
conditions or warranties as to its accuracy or reliability. To the extent permitted by
law, we expressly exclude all conditions, warranties and other terms which might
otherwise be implied by law. This document is subject to change without notice.
Document Control
Document Number crfs-ug-00047
2 • Document Control
Contents
1 Introduction 4
1.1 About this Guide................................................................................................................ 4
1.2 Additional Information ...................................................................................................... 5
3 Components 7
3.1 Key Components of the RFeye Outdoor Kit .................................................................... 7
5 Installation Procedure 19
5.1 ODK RFeye Node top U-bolt........................................................................................... 19
5.2 Left antenna bracket / pole ............................................................................................. 22
5.3 Right antenna bracket / pole........................................................................................... 25
5.4 Main pole mounting bracket .......................................................................................... 29
5.5 PDDM battery connection ............................................................................................... 33
5.6 POnE box pole / mast mounting .................................................................................... 35
6 Antenna Information 38
6.1 Supplied antenna models ............................................................................................... 38
6.1.1 ACC-ANT0040 ...................................................................................................... 38
6.1.2 ACC-ANT0015 ...................................................................................................... 42
7 Disposal 45
crfs-ug-00047 Contents • 3
1 Introduction
The RFeye Outdoor Mounting Kit (ODK) has been designed for quick and easy
deployment with maintenance-free use. In keeping with this approach, CRFS supply a
complete pre-assembled Outdoor Mounting Kit for easy attachment to a pole or mast.
4 • Introduction
1.2 Additional Information
More details on specific usage and applications of the RFeye Node and associated
software are given in the following documents:
RFeye Node User crfs-ug-00009 Using the RFeye Node, programming and
Guide remote control
RFeye Logger User crfs-ug-00041 Logging of spectrum survey data using the
Guide Logger software
RFeye Site User Guide crfs-ug-00042 Real-time spectrum operations using RFeye
Site application software
crfs-ug-00047 Introduction • 5
2 Health & Safety
Warnings
Warnings
Follow appropriate electrical safety regulations to avoid any risk of electric shock.
Only use the cables and equipment supplied by CRFS. Use of alternatives may cause
a safety hazard.
Cautions
Cautions
The contents of each kit comprise assembled and partially assembled components
including:
crfs-ug-00047 Components • 7
Figure 4: RFeye Node within Outdoor assembly (front)
Back View
1 x POnE Box
8 • Components
Left and Right antenna mounting brackets
1 x Left
1 x Right
crfs-ug-00047 Components • 9
Left and Right antenna mounting poles
1 x Right
1 x Left
Figure 10:
10 : Left antenna
antenna mounting pole
10 • Components
1 x 0.8 – 6 GHz
GHz Antenna
Figure 11:
11 : 0.8 – 6 GHz Antenna
1 x 10 – 800 MHz
MH z Antenna
Figure 12:
12 : 10 – 800 MHz Antenna
2 x N-
N-type to N-
N-type RF coa
coaxial cable
Figure 13:
13 : N-type to N-
N-type RF coaxial cable
crfs-ug-00047 Components • 11
1 x System Tester
Figure 14:
14 : System Tester
12 • Components
4 ODK Mounting Kit bags
bags
4.1 Metalwork / Hardware
Each ODK is supplied with a neoprene kit bag containing all parts needed to mount
the ODK or a pole or mast and also the antennas to the main RFeye Node assembly.
Figure 15:
15: Clamp for pole / mast mounting
Figure 16:
16 : Clamp for antenna pole mounting
Figure 17:
17 : M6x120mm Coach Bolt
5 x M6 U-
U-Bolts
Figure 18:
18 : M6 U-Bolt
30 x M6 Flat Washers
Figure 19:
19 : M6 Flat Washer
24 x M6 Split Washers
Figure 20:
20 : M6 Split Washer
Figure 21:
21 : M6x12 Button head screw
Figure 22:
22 : M6x16 Button head screw
22 x M6 Nuts
Figure 23:
23 : M6 Nut
4 x M6 Wing nuts
Figure 24:
24 : M6 Wing nut
Figure 25:
25 : M6 Earth braid / strap
1 x Safety cable
Figure
Figure 26:
26 : Safety cable
Figure 27:
27 : Battery Isolation dongle
Figure 28:
28 : Hex T-
T-Bar
Figure 29:
29 : System Recovery Key
Figure 30:
30 : Wire security
s ecurity / tamper seal
1 x 10mm Combi
Combi Spanner
Figure 31:
31 : 10mm Combi Spanner
Figure 32:
32 : #2x100mm crosshead screwdriver
Figure 33:
33 : RJ45 Connector shell
Note:
Note: The RFeye Outdoor Mounting Kit is designed to be maintenance-free.
However it is prudent to regularly check the top surface of the Kit is free from
obstructions that may impede the performance of the integrated GPS and cellular
antennas.
Note:
Note: Always disassemble the Outdoor Mounting Kit back to supplied
component parts and load into supplied transport case prior to transporting the
system between installation sites.
Figure 35:
35 : U-
U-bolt assembly (2)
20 • Installation Procedure
Figure 36:
36 : U-
U-bolt assembly to top panel (1)
Figure 37:
37 : U-
U-bolt assembly to top panel (2)
Figure 38:
38 : Left antenna bracket and pole assembly (1)
Figure 39:
39 : Left antenna
antenna bracket and pole assembly (2)
22 • Installation Procedure
Assembled pole in bracket:
Figure 40:
40 : Left antenna
antenna bracket and pole assembly (3)
Pass 1 N-type to N-type coaxial cable through grommet on bottom of bracket and connect to
antenna, assemble antenna to pole as shown below:
Figure 41:
41 : Left antenna to antenna pole assembly
Figure 42:
42 : Left antenna bracket to ODK assembly
Figure 43:
43 : Left antenna cable connection
24 • Installation Procedure
5.3 Right antenna bracket / pole
Assemble the right antenna to its mounting pole as shown below:
Connect 1 x N type to N type coaxial cable to antenna and pass through antenna
mounting pole:
Figure 44:
44 : Right antenna to antenna pole assembly (1)
Figure 45:
45: Right antenna to antenna pole assembly (2)
Figure 47:
47 : Right antenna
anten na pole to bracket assembly (2)
26 • Installation Procedure
Figure 48:
48: Right antenna, antenna pole and bracket assembly complete
Figure 49:
49 : Right antenna bracket to ODK assembly
Figure 50:
50 : Right antenna cable connection
28 • Installation Procedure
5.4 Main pole mounting bracket
The ODK main pole mounting kit allows the RFeye Node to be mounted on either a
vertical or horizontal pole. Size of pole can range from 34mm – 80mm dia.
Figure 51:
51 : ODK main mounting brackets, cross section (min. pole diameter)
Figure 52:
52 : ODK main mounting
mounting brackets, cross section (max. pole diameter)
Figure 54:
54 : ODK pole mounting (2)
30 • Installation Procedure
Figure 55 : ODK pole mounting (3)
Figure 56:
56 : ODK pole mounting (4)
Figure 58:
58 : ODK pole mounting (6)
32 • Installation Procedure
5.5 PDDM battery connection
The battery inside the RFeye Node ODK is shipped unconnected to the PDDM. The
battery has a small sticker across its terminals that needs to be removed and two
flying leads connected.
Figure 59:
59: ODK with sunshield attached
Figure 60:
60 : ODK with sunshield removed
Remove 6 crosshead screws to access the internal battery, remove warning sticker,
and connect two flying crimp leads to battery terminals observing polarity:
Figure 61:
61 : PDDM battery, attached to PDDM lid
Screw down PDDM case lid and reinstall sunshield, secure the sunshield with 2 of the
wire security / tamper seals.
34 • Installation Procedure
5.6 POnE box pole
pole / mast mounting
Inside the POnE box supplied is a small hardware kit for mounting to a pole / mast.
Assemble as shown below
Figure 62:
62 : POnE box pole mounting assembly (1)
Figure 64:
64 : POnE
POnE box pole mounting assembly (3)
36 • Installation Procedure
Open the POnE enclosure to gain access to power connector:
Figure 65:
65 : POnE box access for connections (1)
It is not possible to remove the right angle power connector unless the internal plate
is unscrewed:
Figure 66:
66 : POnE box access for connections (2)
Cable the connector, secure with P-clips, and feed power cable through gland. Feed
POnE IN and OUT cables through second gland, and connect to POnE device. Secure
internal plate, ensure lid gasket is in place and screw closed case lid.
6.1.1 ACC-
ACC-ANT0040
Figure 67:
67 : ACC-
ACC -ANT0040
38 • Antenna Information
Gain by frequency:
Figure 68:
68 : ACC-
ACC -ANT0040 Gain (dBi) by Frequency (GHz)
In the following far field plots, Theta is the angle from the vertical:
Figure 69:
69 : ACC-
ACC -ANT0040 Calculated far field gain 0.1 GHz
Figure 71:
71 : ACC-
ACC -ANT0040
ANT00 40 Calculated far field gain 0.5 GHz
40 • Antenna Information
Figure 72:
72 : ACC-
ACC -ANT0040
ANT00 40 Calculated far field gain 0.8 GHz
Figure 73:
73 : ACC-
ACC -ANT0040
ANT 0040 Calculated far field gain 1.0 GHz
6.1.2 ACC-
ACC-ANT0015
Figure 75:
75 : ACC-
ACC -ANT0015
42 • Antenna Information
Frequency range: 0.6 – 6 GHz (typically used 0.8 – 6 GHz)
Connector type: N-type
Power handling: 100 W
VSWR: 2.5:1 Max, 1.7:1 Typ.
Gain: Typ. 2.0dBi
Weight: 325 g
Size (max): 108mm dia. x 165 height (incl. connector)
Figure 76:
76 : ACC-
ACC -ANT0015 Azimuth Pattern
44 • Antenna Information
7 Disposal
The equipment should be disposed of in accordance with local regulations.
crfs-ug-00047 Disposal • 45
8 CRFS Contact Information
8.1 CRFS Support
Central CRFS Support:
Telephone: +44 (0)1223 815615
Email: support@crfs.com
Skype: CRFS Support