Professional Documents
Culture Documents
Amcc S3051a
Amcc S3051a
DEVICE
SPECIFICATION
2.5 GBPS LIMITING AMPLIFIER S3051
2.5 GBPS LIMITING AMPLIFIER S3051
APPLICATIONS
• SONET OC-48
• Fiber Optic Data Links
• High-Speed FM Limiting Amplifier
CBYP
V+REF
VCC
CIN
OUT+ DIN+ DOUT+
S3051
INPUT CIN
OUT– DIN- DOUT–
CBYP
V–REF
DETAILED DESCRIPTION
The S3051 is an integrated limiting amplifier in- The referred wideband input noise (160 µVrms) al-
tended for high-frequency fiber-optic applications. lows for a less than 1E-9 Bit Error Rate for inputs
The circuit connects to typical transimpedance am- down to 2 mVp-p.
plifiers found within a fiber-optic link. The linear
The S3051 is designed to allow adjustment of the
signal output from a transimpedance amplifier can
DC offset between the DIN+ and DIN– inputs. V+REF
contain significant amounts of noise, and may vary
can be used as a reference from which the required
in amplitude over time. The S3051 limiting amplifier
offset can be subtracted to set the DC bias level at
quantizes the signal, and outputs a voltage limited
DIN–. Similarly, V–REF can be used to set the DC
waveform over a 38 dB input dynamic range.
bias level at DIN+. (See Application Information).
At low signal levels, below 12 mVp-p, the circuit be-
If no adjustment is made to the input DC bias level,
haves as a linear amplifier. At higher levels the
two resistors can be connected in a negative feed-
device becomes a limiting amplifier.
back configuration in order to cancel any DC offset
at the input. This will minimize the pulse width distor-
tion. (See separate S3051 Limiting Amplifier
Application document.)
8 7 6 5
110pF
4
5kΩ GND(OB)
9 50Ω
V–REF
5kΩ
3
10 DOUT–
DIN–
11 GS1 GS2 OB
DIN+ 2
DOUT+
5kΩ
12 50Ω
V+REF
5kΩ 1
GND(OB)
110pF
13 14 15 16
Thermal Management
Device Max Power Θja
S3051 750 mW 60˚ C/W
GND
GND
VCC
VCC
16
15
14
13
GND 1 12 V+REF
S3051
DOUT+ 2 11 DIN+
TOP VIEW
GND 4 9 V–REF
5
8
GND
GND
VCC
NC
VCC
DOUT+, DOUT– (with 50Ω load) 2.5 V
+0.3
VIN+
5mV Min
500mV Max
VIN–
VOUT+
300mV
Min
VOUT–
APPLICATIONS INFORMATION
Connecting to the Input of S3051
The equivalent input circuit of S3051 is shown in Figure 7. Both DC biasing and 50 Ohm input line termination
have been implemented internally.
VCC VCC
110pF
0.047 µF 5Ω V–REF
5 kΩ 5 kΩ
9
50Ω
0.047 µF DIN-
VIN–
10
0.047 µF DIN+
VIN+
11
5 kΩ 5 kΩ
50Ω
0.047 µF 5Ω V–REF
12
110pF
5V +5V
Zo=50Ω VCC–0.4V
DOUT+ 2 19
0.1µF
100Ω
DOUT- 3 18
S3051 S3050
C BYP
V +REF
C BYP
V -REF
C BYP
V +REF
+
DIN+ DOUT+
V OFFSET -
V IN- DIN- DOUT-
C BYP
V -REF
Ordering Information
PREFIX DEVICE PACKAGE
X XXXX X
Prefix Device Package
O 900
IS
1
D
CE
RT
E
IFI
Applied Micro Circuits Corporation • 6290 Sequence Dr., San Diego, CA 92121
Phone: (858) 450-9333 • (800) 755-2622 • Fax: (858) 450-9885
http://www.amcc.com
AMCC reserves the right to make changes to its products or to discontinue any semiconductor product or service without notice, and
advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied
on is current.
AMCC does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey
any license under its patent rights nor the rights of others.
AMCC reserves the right to ship devices of higher grade in place of those of lower grade.
AMCC SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR
USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS.