Professional Documents
Culture Documents
WM311 Homm
WM311 Homm
created on 1.9.2023
# Material Dicke λ R
[cm] [W/mK] [m²K/W]
Thermal contact resistance inside (Rsi) 0,130
1 KNAUF Standard 15A+AL 1,50 0,210 0,071
2 Lámina de aluminio 0,00 160,000 0,000
3 KNAUF Standard 12,5A 1,25 0,210 0,060
4 KNAUF Insulation Ultracoustic Plus 7,00 0,035 2,000
Steel (Width: 0,06 cm) 7,50 50,000 0,002
Steel (Width: 0,06 cm) 0,50 50,000 0,000
Steel (Width: 0,06 cm) 0,50 50,000 0,000
Steel (Width: 5 cm) 0,06 50,000 0,000
Steel (Width: 5 cm) 0,06 50,000 0,000
5 KNAUF Insulation Ultracoustic Plus 5,00 0,035 1,429
6 KNAUF Insulation Ultracoustic Plus 10,00 0,035 2,857
Steel (0,092%) 10,00 50,000 0,002
Steel (Width: 0,06 cm) 0,50 50,000 0,000
Steel (Width: 0,06 cm) 0,50 50,000 0,000
Steel (Width: 5 cm) 0,06 50,000 0,000
Steel (Width: 5 cm) 0,06 50,000 0,000
7 KNAUF Aquapanel Outdoor 1,25 0,350 0,036
Thermal contact resistance outside (Rse) 0,040
Thermal contact resistances have been taken from DIN 6946 Table 7.
Rsi: heat flow direction horizontally
Rse: heat flow direction horizontally, outside: Direct contact to outside air
Upper limit of thermal resistance Rtot;upper = 6,609 m²K/W.
Lower limit of thermal resistance Rtot;lower = 3,672 m²K/W.
Check applicability: Rtot;upper / Rtot;lower = 1,800 (maximum allowed: 1,5)
DIN 6946 must not be used because the ratio of the upper limit value of the thermal resistance to the lower limit value of the
thermal resistance is more than 1.5.
Heat transfer coefficient from finite-elements method U = 0,182 W/(m²K)
outside
12,5 7
100 6
260,01
50 5
70 4
12,5 3
15 1 2
inside
50 600
50
Page 1
WM311 HOMM, U=0,18 W/(m²K)
Temperature profile
Temperature profile
20 Temperature
18 1 Dew point
16 2
Temperature [°C]
3 4 5 6 7
14
12
10
outside
8
6
4
2
Left:Temperature and dew-point temperature at the place marked in the right figure. The dew-point indicates the
temperature, at which water vapour condensates. As long as the temperature of the component is everywhere above the dew
point, no condensation occurs. If the curves have contact, condensation occurs at the corresponding position.
Right: The component, drawn to scale.
Page 2
WM311 HOMM, U=0,18 W/(m²K)
Page 3
WM311 HOMM, U=0,18 W/(m²K)
Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 20°C und 50% Humidity; outside: 6.2°C und 71% Humidity (Climate according to user input).
This component is free of condensate under the given climate conditions.
Humidity
The temperature of the inside surface is 19,2 °C leading to a relative humidity on the surface of 53%.Mould formation is not
expected under these conditions.
The following figure shows the relative humidity inside the component.
3 4 5 6 7
70
60
50
outside
40
30
20
10
0
0 50 100 150 200 250
Inside [mm] inside
Outside
50 600
1 KNAUF Standard 15A+AL (15 mm) 4 KNAUF Insulation Ultracoustic Plu... 6 KNAUF Insulation Ultracoustic Plu...
2 Lámina de aluminio 5 KNAUF Insulation Ultracoustic Plu... 7 KNAUF Aquapanel Outdoor (12,5 mm)
3 KNAUF Standard 12,5A (12,5 mm) 4 KNAUF Montantes verticales (75x50)
4 KNAUF Montantes verticales (75x50) 5 KNAUF Insulation Ultracoustic Plu...
Notes: Calculation using the Ubakus 2D-FE method. Convection and the capillarity of the building materials
were not considered. The drying time may take longer under unfavorable conditions (shading, damp / cool
summers) than calculated here.
Page 4
WM311 HOMM, U=0,18 W/(m²K)
Page 5
WM311 HOMM, U=0,18 W/(m²K)
Heat protection
The following results are properties of the tested component alone and do not make any statement about the heat protection
of the entire room:
Temperature profile
36 Temperature at 3pm, 11am and 7am
34 1 Temperature at 7pm, 11pm and 3am
32 2
30 3 4 5 6 7 1 KNAUF Standard 15A+AL (15 mm)
Temperature [°C]
28 2 Lámina de aluminio
26 3 KNAUF Standard 12,5A (12,5 mm)
24 4 KNAUF Insulation Ultracoustic Plus (70 mm)
22 5 KNAUF Insulation Ultracoustic Plus (50 mm)
20 6 KNAUF Insulation Ultracoustic Plus (100 mm)
18 7 KNAUF Aquapanel Outdoor (12,5 mm)
16
14
0 50 100 150 200 250
Inside [mm]
Outside
The calculations presented above have been created for a 1-dimensional cross-section of the component.
Page 6