Professional Documents
Culture Documents
Pryda-Timber Connections
Pryda-Timber Connections
October 2014
Catalogue
Contents 0800 88 22
Angle Brace......................................................................................................................................................................................................................................................03
Batten/Purlin Strap.....................................................................................................................................................................................................................................04
Bottom Plate Anchor.................................................................................................................................................................................................................................05
Bracing Anchor ..............................................................................................................................................................................................................................................06
Ceiling and Purlin Hanger........................................................................................................................................................................................................................07
Concealed Purlin Cleat ..........................................................................................................................................................................................................................08
Cyclone Strap.................................................................................................................................................................................................................................................. 09
Ezi Stud Tie........................................................................................................................................................................................................................................................10
Fix & Foil Fix......................................................................................................................................................................................................................................................11
Framing Bracket............................................................................................................................................................................................................................................12
Frame Fix.............................................................................................................................................................................................................................................................13
Header Block Anchor................................................................................................................................................................................................................................14
Jamb Fixa............................................................................................................................................................................................................................................................15
Jamb Tie...............................................................................................................................................................................................................................................................16
Knuckle Nailplates.......................................................................................................................................................................................................................................17
Knuckle Angle Nailplates.......................................................................................................................................................................................................................18
Knuckle Nailplate Coils ..........................................................................................................................................................................................................................18
Multigrips.............................................................................................................................................................................................................................................................19
Nail-on Angle...................................................................................................................................................................................................................................................20
Nail-on Diagonal Cleat.............................................................................................................................................................................................................................21
Nail-on Joist and Split Joist Hangers..........................................................................................................................................................................................22
Nail-on Plate.....................................................................................................................................................................................................................................................23
6kN Pile-Bearer Kit...................................................................................................................................................................................................................................24
12kN Pile-Bearer Kit.................................................................................................................................................................................................................................25
Plumbers Strap...............................................................................................................................................................................................................................................26
Pole to Girt Brackets..................................................................................................................................................................................................................................27
Product Nails, Fasteners & Screws...............................................................................................................................................................................................28
Sheet Brace Anchor...................................................................................................................................................................................................................................29
Sheet Brace Straps.....................................................................................................................................................................................................................................30
Strap Nail.............................................................................................................................................................................................................................................................31
Strapbrace & Maxi Strap.........................................................................................................................................................................................................................32
Stren-Joist..........................................................................................................................................................................................................................................................34
Tim-Con Bracket...........................................................................................................................................................................................................................................35
Truss Boots........................................................................................................................................................................................................................................................36
Windstrap............................................................................................................................................................................................................................................................37
“Z” and “U” Nails.............................................................................................................................................................................................................................................38
Substitution Guide.......................................................................................................................................................................................................................................39
02
Angle
88 22 44
Brace 0800 88 22
Specifications
Size: 20 x 20 x 1.00mm
Material: G300 Z275 galvanised steel
Product Code:
AB30 (3.0m) AB42 (4.2m)
AB33 (3.3m) AB48 (4.8m)
AB36 (3.6m)
Packing: Bundles of 10 lengths.
Features Applications
Pryda Angle Brace is the fast effective way to brace Used as a fast and effective bracing method for use in in-
interior or exterior timber framing. It is fitted by terior or exterior timber framing in a “closed” environment
making a single saw cut into the studs, inserting the as defined in NZS3604:2011 Table 4.2
brace, then nailing.
03
Batten/Purlin
Strap 0800 88 22
Features Specifications
The Pryda BS70 Batten/Purlin Size: Suitable for 70 x 45mm batten/purlin on flat
Strap provides a simple solution
for tying down roof battens to Material: 1.00mm G300 Z275 galvanised steel
trusses or rafters. Product Code: BS70
Packaging: 70 per carton
The Pryda BS70 has high uplift
capacity, is fast and easy to install
and suitable for all New Zealand
wind zones.
Installation
Place the Batten Strap over the Batten Span Batten Wind Cat. Characteristic Strength Loads
batten and fix both the strap and (mm) Spacing for BS70 acting up/down
batten to the supporting truss or (mm) M* M*
rafter with one galvanised 100 x
3.75mm flat-head nail. Hammer 900 900 VH SG8
all of the claw nails into the truss 900 1200 VH SG8
chord or rafter. The BS70 is only 1200 900 VH SG8
suitable for use with 70 x 45mm 1200 1200 Med SG10
on flat.
Table based on 70 x 45mm batten/purlin on flat.
04
Bottom Plate
88 22 44
Anchor 0800 88 22
Specifications
Installation
Features 1. Tack nail anchors to top edge of boxing at maximum 900 ctrs
(if wall contains sheet brace element, one anchor must be
• Alternative to NZS 3604:2011 Bolt/ positioned 250mm from sheet edge). Position anchors with
Dowel fixing of timber wall plate to tabs horizontal and crimped end downwards at 45° angle.
concrete slab. 2. After initial concrete cure, position wall frame.
• Speedier concrete finishing - allows 3. Bend anchor up and over plate and nail with 30 x 3.15mm
floating to slab edge and avoids messy Pryda Product Nails - 2 into edge of plate and 2 per tab. If
hand trowelling around cast-in bolts. tabs coincide with stud position, nail to stud with 2 per tab.
• Easier wall frame placement - no drilling 4. Fix one 75 x 4mm concrete nail adjacent to anchor, minimum
of plates and no lifting / locating over 70mm from edge and slab
preplaced bolts.
• Cost savings over cast-in anchor bolts.
NOTE: Bottom plate fixings are designed to be used in DRY service conditions
- i.e., with concrete protected from moisture by continuous damp proof
membrane.
CAPACITIES*
(per anchor in 17MPa concrete) as per
NZS3604:2011 c1 7.5.12.3/4 Tack anchor on top of edge of
formwork
Along Plate
Basic Load = 2.2 kN
Ensure that the DPC is
Design (W or E) = 3.9 kN
Capacity = 6.4 kN pushed hard into the slab
corner before placing the
anchor.
Across Plate
Basic Load = 1.6 kN Four 30 x 3.15mm Pryda
Design (W or E) = 2.8 kN Product Nails into top of
Capacity = 5.1 kN wall plate.
Two Timber
Connector
Nails into
Uplift edge of
Basic Load = 2.5 kN plate
Design (W or E) = 4.4 kN
Capacity = 8.0 kN
05
Bracing
Anchor 0800 88 22
Specifications
Installation
External Brace Wall Internal Brace Wall External Brace Wall Internal Brace Wall
To comply with concrete and PBA shall be fixed centrally to PBA shall be fixed centrally over PBA shall be fixed centrally on the bottom
timber edge distance, bracket the wall frame. a solid joist using an M12 x plate using an M12 x150mm galv coach
shall be located 10mm from 150mm galvanised coach screw. screw ensuring that screw is fixed centrally
inside face of bottom plate. into a solid joist. Extra solid nog may be
Refer to 15kN proprietary fixing required to achieve solid fixing.
manufacturers requirement for
concrete edge distance.
06
Ceiling and
88 22 44
Features Specifications
07
Concealed
Purlin Cleat 0800 88 22
Features Specifications
The above uplift loads apply to J4/J5 timber solutions. The loads do not
change for the longer screws used in ceiling plate situations.
08
Cyclone
88 22 44
Strap 0800 88 22
Alternate the
truss/rafter to
the strap is fi
Cyclone Strap
Cyclone Strap
est design capacity. Tests have Product Code MPQHS4 80 per carton tie
or
32 mm
the strapor is fixed
rafter
400
MPQHS4
Characteristic 32 mm
Load Strength (kN)
600
MPQHS6
Roof truss or rafter
or beam
Direction 32 mm
J4 J5
900
QHS9
Cyclone Strap
FIG 1 FIG 2
ties down truss
32 mm Cyclone Strap or rafter to the
Steel 400 14.5 14.5 wall frame
MPQHS4 fixes purlin to Top plate
3 nails/leg 6.5 4.7 truss top chord
or rafter32 mm
4* nails/leg 8.6 6.3 32 mm 400
600 MPQHS4
5* nails/leg 10.8
MPQHS6 7.9 600
MPQHS6
32 mm
32 mm
400
MPQHS4
32 mm
09
600
Ezi
Stud Tie 0800 88 22
Specifications
Installation
Features
Prior to use, the Pryda Ezi Stud Tie shall be stored
The Pryda Ezi Stud Tie - SST (STS25) has been in weatherproof environment and protected from
designed to exceed the requirement of table 8.18 moisture. Care must be take to avoid any damage
NZ3604:2011 – “Fixing of top plate of wall to to the surface of the product that may affect the
supporting members such as studs and lintels at protective galvanised coating.
600mm centres”. The Pryda Ezi Stud Tie is not
reliant on the position of the top plate fixing nails to Installation is self evident and normal good building
achieve desired strength. practice is assumed during installation. The Pryda
Ezi Stud Tie can be fixed in the pre-nail stage or on
site using a carpenters’ hammer requiring no special
skill or other tools.
Advantages
• Easy to install
• No checking of timber required
Application
• Can be fitted after top plate packer has been
attached The Pryda Ezi Stud Tie is an alternative solution to
• Prebent to ensure correct placement on site the fixing type B in Table 8.18 in NZ3604:2011. The
• Smaller top plate connection – Quicker and easier Pryda Ezi Stud Tie exceeds the required capacity
to fix without relying on the additional 0.7kN contribution
• Less cumbersome – Smaller but effective of the 2/90x3.15 nails, top plate to stud.
• Easily installed using just a hammer
• Easily inspected
Durability
10
Fix &
88 22 44
The non-tear economical fixings for sheet insulation and shade netting.
Specifications
PRYDA FIX (for shade cloth) and PRYDA FOIL FIX The exclusive twisted nail profile suitable for use
(for insulation foil) are manufactured from 0.8mm with the hardest of timbers resists “pull out”. The
galvanised steel (275 gm/m2). The plates are designed foil is held securely in position whilst tearing in
to eliminate tearing on sharp surfaces, the rounded windy conditions is prevented due to the rounded
coined edge holding the material firmly against the coined edges of the plate.
timber when the pre-punched nails are driven home. FOIL FIX - SAFE LOADS: For all timbers with
They are manufactured in easy snap off stick form for joint group J4 or better, the holding power
speed and safety. exceeded the tearing strength of the foil.
11
Framing
Bracket 0800 88 22
Specifications
Sizes: Product Code denotes the size of the timber
the product is suitable for, e.g. FB4590 is
suitable for 45 mm x 90-150mm
Material: 1.0mm G300 Z275 or G300 Z600
galvanised steel or stainless
Loads
12
Frame
88 22 44
Fix 0800 88 22
Specifications
Durability
Features Application
The Pryda Frame Fix (PFF) has been The PFF is intended to re-instate the structural integrity
designed to allow a service hole of no greater than of both 90 x 45mm and 140 x 45mm wall frame top
60mm to be drilled through a top plate (including top plates (including a top plate packer if used) or wall studs
plate packer if used) or wall stud to allow services that have had a service hole of no greater than 60mm
such as air conditioning or central vacuum pipes to diameter drilled through it’s centre.
be passed through the member. The fitting of a PFF
re-instates the integrity of the penetrated top plate
or stud. Installation
A bottom plate tie down for use with concrete header block bases.
Features Specifications
Installation
Pryda Header Block Anchors are fitted at 600mm
centres or less over the outside edge of the header
block before the concrete is poured.
14
Jamb
88 22 44
Fixa 0800 88 22
20mm
175mm
Features Specifications
Installation
15
Jamb
Tie 0800 88 22
Specifications
Features
Installation
1. Use scribed line to accurately position each 4. Plumb the door jamb using the slots for any re-
Jamb-Tie square across the back face of door quired adjustment, then fix brackets by nailing the
jamb then hammer fix into jamb. On grooved remaining holes. Repeat with jamb on opposite side
jambs the Tie should bend at the inner edge of of opening, then adjust and fix all remaining brack-
each groove; on plain jambs position the scribe ets in the same way. Before fixing brackets make
line on the jamb edge to allow for 10mm thick- sure the jamb is plumb.
ness wall lining to finish flush with the edge of
the jamb 5. Window Fixing: Pryda Jamb-Ties can be used for
fixing timber or aluminium windows that have timber
2. Lift the jamb into place and bend the end of two reveals. Fixing details are as per door jamb installa-
brackets around the opening studs to hold the tion.
door jamb in place.
Nailplates 0800 88 22
Specifications
Specifications
Knuckle Nailplate
Coils
A simple, efficient and convenient connector.
Specifications
Features
18
88 22 44
Multigrips 0800 88 22
2 Nails
4 Nails
Specifications
4 Nails
2 Nails
1 6.5 4.7
2 4.3 3.2 4 4 Nails
3
3 3.1 2.3 2 Nails
MGL has a design capacity for wind uplift as follows: 3.4kN 4 Nails
4 Nails
2 Nails
19
Nail-on
50mm Leg
Angle
190
mm
Le 0800 88 22
ng
th
eg
mL
50m
50mm Leg
190
mm
Le
ng
th
Load Direction
eg
mL
50m
Features Specifications
Ideal for beam to bearer situations to give a strong, Pryda Nail-on Angle is manufactured from 190 x 100 x
Nail-On angle both sides of joist
economic alternative to framing brackets where the 1.0mm Nail-on Plate, folded in half along its length.
width of the beam is non-standard.
Material: 1.0mm G300 Z275 galvanised
steel.
Product Code: NPA
Packing: 25 per carton.
Load Direction
Nails Design Loads
• Use Pryda Product Nails (30mm x 3.15mm Design loads are for two Nail-on Angles per joint each
diameter Flat Head galvanised nails) or fully nailed with 20 nails/flange into SG8 timber.
equivalent.
• Use 75 x 3.15 diameter Flat Head nails when Characteristic Strength Loads acting up/down (kN)
nailing into poles.
J4 J5
34.8 25.5
20
Nail-on Diagonal
88 22 44
Cleat 0800 88 22
eg
m mL
100
Nails Specifications
• Use Pryda Product Nails (30mm x 3.15mm Material: 1.0mm G300 Z275 galvanised
galvanised nails) or equivalent. steel.
• Use 75 x 3.15 diameter Flat Head nails when
Product Code: NPD
nailing into poles (e.g., girt to pole fixing)
• 20 Nails required in each flange to achieve Packing: 10 LH & 10RH per ctn.
19
stated design loads (Beam to Beam Connec- Pryda Nail-on Diagonal Cleat is manufactured from 190
0m
m
either LH or RH Cleats.
ng
th
eg
m mL
Loadings 100
Load Direction
21
Nail-on Joist and Split
Joist Hangers 0800 88 22
High capacity Joist Hangers suitable for timber various height and widths.
50
Features Specifications
22
Nail-on
88 22 44
Plate 0800 88 22
Installation
75
/1
50
mm
12g x 35mm hex head screws.
Fill all nail or screw holes.
Installation
Specifications
Pryda Nail-on Plate provides a quick and economical means
of providing a strong joint for many on-site applications. Sizes: Width – 75, 100, 150mm
Material:
1.0mm G300 Z275 or G300 Z600 galvanised
Loads steel or stainless steel or 2.0mm G300 Z275
galvanised steel
Steel Strength (Per Pair of Plates) Product Code & Packing
1.0 mm 2.0 mm NPA75 BAR* 1 x 75 x 1260mm 1
NPA75/190 1 x 75 x 190mm 40
Tension
23
Pile-Bearer Kit
6 kN Capacity Fixing of 0800 88 22
6
Cantilever Pile to Bearer
and Joists.
kN
Features Installation
• Allows CANTILEVER Pile to be in line with and As detail drawing above but subject to the
same height as other piles.
2 Nailon Cleats on following:-
joist closest to pile
• Connection detail covers bearer sizes up to 200mm
10 nails per cleat
5 into bearer
deep, joists up to 250mm deep.
5 into joist
1. On round pile bearer must be central. Bearer
• Design capacity verified by extensive testing may be offset on square pile but must not
program carried out by BRANZ. overhang edge.
• AllJoist
Floor components supplied as one complete package. 2. Nail on cleats fix to joist closest to pile. At
(max size 250 x 50)
• Available in all stainless steel components for use in building corner where fixing to boundary joist is
environments with severe corrosion risk. precluded fix cleats to next closest joist along
bearer.
Durability 4 "U" Nails
between pile & bearer 3. At external wall where joists do not overhang
bearer enough for cleats to be fixed on outside
Complies with NZ Building Code - Clause
4 x 4mmB2 for FH
x 100mm a Skew
face, they may be fixed to inside face only of
structural component with 50 year durability.
Nails. 1 each side of bearer,
down into pile. 1 each edge
of pile up into bearer
that bearer provided a similar detail is used on
Bearer (max depth 200mm
the other side of the floor system.
PBK6:
widths 75 or 100mm or
Standard Kit (“U” Nails and 100mm Nails Hot
Cantilever Pile
double 50mm)
150 ø Round or 4. Joist must have lateral support (blocking or
Dip Galvanised, Cleats hot dip galvanised or Z600 gal-
125 x 125SQ
perimeter joist) within 300mm of bearer in
vanised steel coil, 45mm nails HDG) - Not suitable for
accordance with NZS3604:2011 cl 7.1.2.1.
use in Zone D or geothermal zones. Components must
5. All components must be protected after
be minimum 600mm above ground with the sub-floor
installation against wind-blown sea salt
vented to be 7000 mm2/m2 or less. See durability
deposition by coating with 2mm thick grease,
alternative solution table in this catalogue for Zone B
Selleys roof and gutter (silicone) sealant, or
and C.
other approved coating.
PBK6S: Severe Corrosion Kit (All Grade 304
Stainless Steel Components) - suitable for all sea spray
zone conditions.
24
Pile-Bearer Kit
88 22 44 12 kN Capacity Fixing of 0800 88 22
12
Anchor/Braced Pile to
Bearer and Joists.
kN
2 x 4mm x 100mm FH
Also available separately (packing
Galvanised Skew 20 per carton)
Nails each side: Through pile
into bearer (4 Total) Nails 45 x 3.15mm Flat Head Square
Twist (74 off)
Anchor or Braced Pile 100 x 4.0mm Flat Head (4 off)
Bearer (max depth 200mm 150mm ø Round or
widths 75 or 100mm or 125 x 125mm SQ scarf cut to G300 Z600 galvanised steel.
same width as bearer at 1:4 slope Material:
double 50mm) Stainless steel.
12 kN HORIZONTAL CAPACITY Fixing of Bearer/
Joists to ANCHOR PILE or BRACED PILE, in
accordance with NZS 3604:2011 Clauses 6.8.5, 6.8.6
and 6.9.3.
Features Installation
2 Nailon Cleats on 1mm Nailon Plate
each of 2 joists each side Floor Joist
• Allows ANCHOR/BRACED Pile to be in line(max size 250
closest to pile 16 nails per plate Asx 20)
detail drawing above but subject to the following:-
10 nails per cleat in random pattern
with and same height as other piles.
5 into bearer 8 into pile
5 into joist 8 into bearer
• Connection detail covers both Anchor and 1. On round pile bearer must be central. Bearer may be
Braced Piles, with bearer sizes up to 200mm offset on square pile but must not overhang edge.
deep, joists up to 250mm deep. 2. Nailon cleats fix to two joists closest to pile. At building
• Design capacity verified by extensive testing corner where fixing to boundary joist is precluded fix
program carried out by BRANZ. cleats to next two closest joists along bearer.
• All components supplied as one complete 3. At external wall where joists do not overhang bearer
package. enough
2 x 4mm x 100mm FH for cleats to be fixed on outside face, they may
Galvanised Skew
beThrough
Nails each side: fixedpileto inside face only of that bearer provided
into bearer (4 Total)
Durability a similar detail is used on the other side of the floor
system.
Anchor or Braced Pile
Complies with Bearer
NZ Building Code
(max depth 200mm
- Clause B2 for150 ø Round or 125Joists
a 4. x 125SQ must have lateral support (blocking or perimeter
scarf cut to same width as bearer
structural component
widths 75 or
double 50mm)
with 50 year durability.
100mm or
at 1:4 slope joist) within 300mm of bearer in accordance with
NZS3604:2011 cl 7.1.2.1.
PBK12: Standard Kit (Nail-on plates/Nails Hot 5. Braced Piles - connection is required at top of both
Dip Galvanised or Z600 galvanised steel coil) - piles to which each brace attaches.
Not suitable for use in Zone D or the geothermal 6. All components must be protected after installation
zones. Components must be minimum 600mm against wind-blown sea salt deposition by coating with
above ground and the sub-floor vented 7000 2mm thick grease, Selleys roof and gutter (silicone)
mm2/m2 or less in zones B & C. sealant, or other approved coating.
25
Plumbers
Strap 0800 88 22
SBT
Applications Specifications
Pryda Plumber’s Strap has been developed as a
seismic restraint for hot water cylinders and as a Size: 25mm x 0.5mm x 30m
support for water pipes. Material: 0.5mm G300 Z275 galvanised
steel.
Product Code: PS30
Installation Packing: Plumbers Strap, 30m coil – each.
Screws: Type 17 screw 12g or better
Make sure the hot water cylinder is flat on the floor
and hard up against the wall using Pryda Plumber’s Tensioner: Strap Brace Tensioners (SBT)
Strap. Ensure that the straps are screwed to a stud.
Tighten strap with strapbrace tensioners.
26
Pole to Girt
88 22 44
Bracket 0800 88 22
Features Specifications
The Pryda Pole to Girt bracket provides a robust Size 50/50 x 1.0 x 110mm
means of fixing timber girts to poles in Pole & Rafter Material 1.0mm G300 Z275 galvanised
buildings. The bracket is designed in a butterfly steel or stainless steel.
shape to easily wrap around the poles. The NPP2G
is a variation of the multigrip but with greater Product Code Galvanised Stainless
extension into the connected member and with NPP2G NPP2G/S
the addition of screw holes provides greater fiixing Packing 10 per ctn each
capacity.
27
Product Nails,
Fasteners & Screws 0800 88 22
28
Sheet
88 22 44
Advantages
Installation Specifications
13
Installation
29
Sheet
Brace Straps 0800 88 22
Features Specifications
Mild steel strap fixing complying with the require- Sizes: 25 x 1.0 x 300mm
ments of NZS3604:2011 for a 6kN Capacity Strap.
25 x 1.0 x 400mm
Use 2 straps, each with nailing as below, where
12kN Capacity fixing is required. Where straps 25 x 1.0 x 600mm
longer than 600mm are required 10m & 30m coils 25 x 1.0mm x 10m
are now available. The coils can easily be cut to the 25 x 1.0mm x 30m
required length. Material: 1.0mm G300 Z275 galvanised
steel coil or stainless steel.
Product Code: Galvanised Stainless
Applications
SBS300 SBS300/S
Nails with 6 nails at each end of strap for 6KN SBS400 SBS400/S
Capacity fixing. Use Pryda product nails SBS600 SBS600/S
(30 x 3.15mm Hot Dip Galvanised Bracket Nails).
10m coil SBS10M
30m coil SBS30M
Packing: Galvanised Steel: 50 per ctn
Stainless Steel: 10 per ctn
Coils: each.
Nails: 30 x 3.15mm Pryda Product Nails.
Installation
Refer to Pryda Building Guide.
30
88 22 44
Features Specifications
Pryda Strap Nail, a pre-punched nailplate which offers Product Code: MPSN2 MPSN50 SN50L
a quick, simple, economical and easy to use method SN25 SN50
of jointing timber plates normally jointed by more Size: 25mm x 50mm x 50mm x
time consuming methods. Pryda Strap Nail uses the 100mm 100mm 150mm
sharper tooth profile featuring the exclusive
Packing 180 75 70
pre-punched twisted nail. This results in increased
(per ctn): 300 130
holding power due to better penetration of all timber
types. Capacity: 2.3kN 4.6kN 6.0kN
Load parallel or perpendicular to grain in SG8
Pine or Douglas Fir
Installation
31
Strapbrace &
Maxi Strap 0800 88 22
Specifications
Wind
Characteristic
Steel Strength Loading
Strength (kN)
(kN)
Strapbrace 8.2 6.6
Maxi Strap 16.4 13.2
32
Strapbrace &
88 22 44
Continued.
Ceiling Bracing
Wall Bracing
33
Stren-Joist 0800 88 22
Specifications
Material: 1.6mm Z275 galvanised steel.
Product Code: NPSJ
Each kit 1 x ’U’ channel, 2 x arched angles,
contains: 1 x 500gm of Pryda Product Nails
and 10 /8g x 20mm screws. (If
the hex screw fixing option is used
then 30 /12g x 35mm hex head
type #17 galvanised screws are
required.
Packing: 1 per carton
Features Installation
The Pryda Stren-Joist has been designed to allow holes The Pryda Stren-Joist retrofit installation is self-evident and
to be cut in floor joists to enable pipes, wiring or other ser- normal good building practice is assumed during installation.
vices to be passed through the joist. The fitting of a Pryda The product is suitable for the all joist sizes between 140
Stren-Joist re-instates the integrity of the penetrated joist. x 45mm to 290 x 45mm but is not suitable for 90 x 45mm
joist.
Application
Advantages
The Pryda Stren-Joist is intended to re-instate the struc-
• Quick and easy to install tural integrity of joist that has suffered service holes after
• Fixing option of either nailing or screwing. erection. The hole can be made in any position along the
• Note—Fixing to the flooring must be done with screws span of the joist provided that the hole edge is not closer
provided. All other holes can use either nails or screws than one joist depth from the end supports of the joist.
• Can be retro-fitted. There is no requirement to remove
services to fit the Stren-Joist
• Comes in one size, designed to fit 140—290mm
Durability
joists
• Allows an easy solution to fix penetrations in floor joists The durability of the Pryda Stren-Joist is in accordance
made by other trades with the acceptable solutions contained in Table 4.1 of
• Timber grade can be SG8 or better NZS3604:2011 and is intended for internal “closed spaces”.
• The edge of the penetration shall be at least the joist It is not suitable where this table specifies 304 stainless
depth from the end of the joist steel products.
• All components are available in a single kit -
Pryda Code NPSJ.
Maximum Joist Penetration
Joist Size Max Hole size
140 x 45 72mm
190 x 45 122mm
240 x 45 125mm
290 x 45 125mm
34
Tim-Con
88 22 44
Bracket 0800 88 22
Applications Specifications
NAILS: Pryda Product Nails 30 x 3.15mm. Sizes Flanges 40 x 110mm,
The brackets have 32 nail holes in the TCF130, and width 130 or 190mm
48 nail holes in the TCF190. See the load chart below
Material 2.0mm G300 Z275
for the nails required for each application.
galvanised steel.
BOLTS:Use 3/12mm dia. bolts per bracket in the Product Code & Packing
14mm bolt holes. Always use the 3/37 x 37 x 3mm TCF130 20 per carton
washers provided. TCF190 10 per carton
35
Truss
Boots 0800 88 22
TB45/16 TBHD7
Features Specifications
BOLTS:
• M12 bolts must be fitted with nuts and 55mm
diameter or 50 x 50 x 3mm square washers
• M16 bolts must be fitted with nuts and 65mm
diameter or 57 x 57 x 4mm washers.
36
88 22 44
Windstrap 0800 88 22
Specifications
Applications
Features
Loads
37
“Z” and “U”
Nails 0800 88 22
A cost effective fixing for holding down purlins, top plates and trusses.
Specifications
Loads
Loads Characteristic
Direction Strength (kN)
“Z” Nail 3.2
“U” Nail 3.1
38
88 22 44 0800 88 22
Substitution Guide
Please Note: Whilst reference is made to competitor products it is intended as best fit only and may not
be an identical match - if in doubt check.
39
40
CT160HD NPD150/63*
widths 75 or 100mm or
Cantilever Pile
double 50mm)
150mm ø Round or
125 x 125mm SQ Cyclone Straps
(Cyclone Ties)
Angle Brace
Competitor Code Pryda Code Alternate the side of the
2 Nailon Cleats on
(Angle Brace)
joist closest to pile
10 nails per cleat truss/rafter to which
CT400 MPQHS4
5 into bearer
5 into joist
the strap is fixed
Floor Joist
Competitor Code Pryda Code CT600 MPQHS6
(max size 250 x 50)
HBA HBA 32 mm
900 Competitor Code Pryda Code
QHS9
JH3790 MPFB3890
Ceiling & Purlin Hanger JH4790 MPFB4590*
(Ceiling Tie)
JH47120 MPFB45120*
JH47190 MPFB45180*
Competitor Code Pryda Code
JH5290 MPFB5274*
CT160LH CPH126-LH*
JH52120 MPFB52124*
CT160RH CPH126-RH*
JH52190 MPFB52174*
CT200LH CPH190-LH*
— FB65/170
CT200RH CPH190-RH* JH70 FB69/165
FIG 1 FIG 2
JH95 FB94/152*
0800 88 22
88 22 44
Knuckle Nailplates
an identical match - if in doubt check.
* All available in stainless steel. Please Note: Whilst reference is made to competitor products it is intended as best fit only and may not be
Maxi Strap
(Multi-brace)
0800 88 22
41
42 4 Nails
Plumbers Strap
an identical match - if in doubt check.
* All available in stainless steel. Please Note: Whilst reference is made to competitor products it is intended as best fit only and may not be
Multigrip
(Multigrip) (Plumbers Strap)
MGS MGL
Pole to Girt Bracket
(Girt Plate)
Nail-on Angle & Diagonal Cleats
(Diagonal Cleat)
Competitor Code Pryda Code
GIRTPLATE NPP2G*
Competitor Code Pryda Code
19
0m
NP160F NPA
m
Le
ng
Leg
100
mm (GIB HandiBrac)
Nail-on Plate
Competitor Code Pryda Code
(Nail On Plate)
GIB HandiBrac PBA
75
SBS4100 SBS400*
/1
00
— NPA150/250
/1
SBS6100 SBS600*
50
m
m
— NPA150/315 SBS10EX SBS10M
RAFTERSPLICE NPB75/380 SBS30EX SBS30M
— NPB75 BAR^
NP2 NPB100BAR^
— NPB150BAR^
0800 88 22
88 22 44
Strap Brace Truss Boots
an identical match - if in doubt check.
* All available in stainless steel. Please Note: Whilst reference is made to competitor products it is intended as best fit only and may not be
(Strip Brace)
Competitor Code Pryda Code
Competitor Code Pryda Code — TB45/16
SB10 SB10* — TBHD7
SB10T SB10T
SB30 SB30
SB30T SB30 Windstraps
SBTENS SBT*
SSSB10 SB15/S Competitor Code Pryda Code
— SBT/SS316 — WS4E
— WS6E
Strap Nail
(Strap Nail) Z & U Nails
(Wire Dogs)
Competitor Code Pryda Code
SNS SN25 or MPSN2 Competitor Code Pryda Code
— SN50 or MPSN50 WDRHS MPZR/ZR
— SN50L WDLHS MPZL/ZL
WDSS MPZU/ZU
Stren-Joist
Stud Tie
(Stud Tie)
Tim-Con Brackets
(Concrete Fixing Cleat)
0800 88 22
43
Structural Brackets 0800 88 22
5
3 5 5 50
50 75 75
23 23 23
23
60 60
60
60
350 300
300 440
50 5
23 50 3
23
60
50 5
23 50
SBK14
3 5
50 50
60 74 50 (B350)
23 23
280
60 60
74 50 5
200
135 135 23
50
SBK14A ■
50 50 50
50
50 (B55)
SBK10 SBK10A ■ SBK11A SBK12A
(B351) (B51) (B52) (B53)
75 50 50 75
23 23 23
35
60 60 50 300 75
60 300
60 60
230
275
23 23
5 5
5 3 5 5
50 5
23
285
135
135
285
SBK37 ■
SBK34 ■ SBK36 ■ 92X55 CHANNEL INCLUDES 2 M16X140 BOLTS
(B163) (B155)
50 5
23
50 5 50 5 5 50 5
75
23 23 23 23
60
380
200 175 175
175
80
140
44
88 22 44 0800 88 22
5 94 75 94 50
75 5 23
5
23
50 115
50 115
185 345
400 30
345
SBK8 ■ SBK9 ■
SBK5 ■ SBK6 ■ INCLUDES 2 M12X120 HDG BOLTS INCLUDES 2 M12X120 HDG BOLTS
(B195) (B197) (B138) (B135)
5
94 75
5
94
50
23 5
94 50
23
SBK17 ■
23
12MM BOLTS
60 185
94 75 50 115 50 INCLUDED.
5
23 MASONRY
94 75 50 115 150 ANCHOR NOT
5
23 265 SUPPLIED
50 115 415 (B25)
190
SBK16H
435
INCLUDES
5
94 75 SBK18 ■
2 M12X120 23 12MM BOLTS
HDG BOLTS. 50 INCLUDED.
75 75 75 HIGH WIND 150 MASONRY
(B16) ANCHOR NOT
SBK15 SBK16 ■ SBK16B 75 SUPPLIED
INCLUDES 2 M12X120 HDG BOLTS INCLUDES 2 M12X120 HDG BOLTS INCLUDES 2 M12X120 HDG BOLTS
(B28)
(B12) (B14) (B18)
75 50
75 50
130
275
25
75 50
75
100 75
SBK31 ■
230 50
(B175) 280
230
75 50
275
230 130
60
60 50
23 25 25
23 180
25
5
5 5 5 5
5
75
53
280
100
63
75
5 HOLES TO FIT M16 BOLTS
23
50 5
64
30
175 2
DIA 6
330 3
210
72
175 49 150
48
90
WHILST REFERENCE IS MADE TO COMPETITOR PRODUCT IT IS INTENDED AS A BEST FIT ONLY AND MAY NOT BE AN IDENTICAL MATCH - IF IN DOUBT PLEASE CHECK
Whilst reference is made to competitor products it is intended as best fit only and may not be an identical match - if in doubt check.
45
Notes 0800 88 22
46
88 22 44 0800 88 22
47
0800 88 22
Contact Pryda
www.pryda.co.nz
48