Professional Documents
Culture Documents
Ly E67f - en
Ly E67f - en
Ly E67f - en
com
Produktdatenblatt | Version 1.1
LY E67F
LY E67F
Power TOPLED ®
PowerTOPLED, a powerful member of the TOPLED
family. Thanks to their high luminous efficacy, the
LEDs are ideal for rear light clusters and indicators
on vehicles and for display panels for traffic control
systems.
Applications
——Interior Illumination (e.g. Ambient Map) ——Traffic Lights
——Signalling
Features:
——Package: white PLCC-4 package, colorless clear resin
——Chip technology: Thinfilm
——Typ. Radiation: 120° (Lambertian emitter)
——Color: λdom = 593 nm (● yellow)
——Corrosion Robustness Class: 3B
——Qualifications: AEC-Q102 Qualified
——ESD: 2 kV acc. to ANSI/ESDA/JEDEC JS-001 (HBM, Class 2)
Ordering Information
Type Luminous Intensity 1) Ordering Code
IF = 50 mA
Iv
Maximum Ratings
Parameter Symbol Values
Characteristics
IF = 50 mA; TS = 25 °C
Parameter Symbol Values
Brightness Groups
Group Luminous Intensity 1) Luminous Intensity. 1) Luminous Flux 6)
IF = 50 mA IF = 50 mA IF = 50 mA
min. max. typ.
Iv Iv ΦV
3B 2.05 V 2.20 V
4A 2.20 V 2.35 V
4B 2.35 V 2.50 V
5A 2.50 V 2.65 V
Wavelength Groups
Group
Dominant Wavelength 3)
IF = 50 mA
min.
Dominant Wavelength 3)
IF = 50 mA
max.
λdom λdom
3 583 nm 586 nm
4 586 nm 589 nm
5 589 nm 592 nm
6 592 nm 595 nm
AB 3 3B
0,8
0,6
0,4
0,2
0,0
350 400 450 500 550 600 650 700 750 800
λ/
Radiation Characteristics 6)
Irel = f (ϕ); TS = 25 °C
LY E67F
ϕ/
-10° 0° 10° 20° 30° 40° 50° 60° 70° 80° 90°
-20° 1,0
I
-30°
-40° 0,8
-50°
0,6
-60°
0,4
-70°
-80° 0,2
-90° 0,0
-100°
30
0,5
20
10
0,1
5
4
0,05
3
1
1,7 1,8 2,0 2,2 2,4
1
2
3
4
5
10
20
30
40
50
70
VF / V IF / mA
0,2
1,5
0,1
0,0 1,0
-0,1
0,5
-0,2
-0,3 0,0
-40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120
Tj / °C Tj / °C
Dominant Wavelength 6)
λdom = f(Tj); IF = 50 mA
LY E67F
λ / nm
640
620
600
580
560
540
OHL01413
80
mA
IF
70
60
TA TS
50
40
30
20
Τ A temp. ambient
10 Τ S temp. solder point
0
0 20 40 60 80 ˚C 100
T
0.10 0.01 0.10
0.02 0.02
0.05 0.05
0.1
0.08 0.08 0.2
0.5
D= 1
0.06 0.1 0.06
0.2
0.5
1 0.04
0.04
tP tP
0.02 tP IF 0.02 tP IF
D= T D= T
T T
0 0
10-5 10-4 10-3 10-2 10-1 100 101 s 102 10-5 10-4 10-3 10-2 10-1 100 101 s 102
tp tp
Dimensional Drawing 8)
3.7 (0.146)
A C A C
1.1 (0.043)
0.5 (0.020) 0.6 (0.024)
0.4 (0.016)
Package marking
0.18 (0.007)
0.12 (0.005) GPLY6084
Further Information:
Approximate Weight: 30.0 mg
2.3 (0.091)
0.8 (0.031)
1.1 (0.043)
11.1 (0.437)
3.7 (0.146)
1.5 (0.059)
0.7 (0.028)
Kathode/
Cathode
Fläche darf bei Verwendung von TOPLED® Cu Fläche / <_ 16 mm 2 per pad
elektrisch nicht beschaltet werden. Cu-area
For TOPLED® assembly do not use
this area for electrical contact
Lötstoplack
Solder resist OHLPY440
For superior solder joint connectivity results we recommend soldering under standard nitrogen atmosphere. Package not
suitable for ultra sonic cleaning.
150
tS
100
50
25 ˚C
0
0 50 100 150 200 250 s 300
t
TSmax to TP
Liquidus temperature TL 217 °C
Time above liquidus temperature tL 80 100 s
Peak temperature TP 245 260 °C
Time within 5 °C of the specified peak tP 10 20 30 s
temperature TP - 5 K
Ramp-down rate* 3 6 K/s
TP to 100 °C
Time 480 s
25 °C to TP
All temperatures refer to the center of the package, measured on the top of the component
* slope calculation DT/Dt: Dt max. 5 s; fulfillment for the whole T-range
Taping 8)
1.75 (0.069)
8 (0.315)
3.5 (0.138)
3.6 (0.142)
2.9 (0.114)
4 (0.157) OHAY0667
Reel Dimensions
A W Nmin W1 W2 max Pieces per PU
Barcode-Product-Label (BPL)
N s E RS
L
E
re
V
E
tiv
If
e
la ared ag
fr
in pa
L
hu
ck
an
m
id
k,
bl r co
ba
e
de
e be
sela
ity
30
l
˚C
).
(R
/6
R
H
0%
.
Barcode label
TIO
<
_
in IV O % k
IT T of
nta
90 to rs
S C < d ea s ). rs
N U ou
U coSEND d te (p on ,
or de H rs
iti ou
an bjec ng
ou rs
Ais bUagRMEICO ˚C co 72 H
si nd 5 H ou
˚C su es te 48
CThIS co ± e H
y da e 24 6
T E 40 be oc
or ˚C tim e
S < ill pr). ith or tim
O w nt ct 23 w tim e
M TO
at fa lo or
s at le ˚C at at e. al F lo or tim
P th th va l tic F lo or
O on s ui be if: read
ur F lo
m ce eq la lo
w ed
id
en l 4 5 F
vi g, n oc ve l
24 or de be in pr is 5a
de , e nt whe Le ve l 6
te
g: , w
r
co
se ou ke e Le ve l
da Le ve
ba ed flo
ba e m % ba al st
ur e
en re r ur e Le
ed e e tim re> 10 fo se oi st ur e
al op se fo M oi st ur
se is as or . is 33 k, M oi st
k, lo H bed
in g ph , -0 an M oi
e r- an in F R ng ar D bl M
ba
lif is po If bl ith % ki r C. S
T (if r
lf th va p. w 10 ba to et J- ea r ks
he r w, m <
_ m Y ea rs
S te ed iredicat d, EC 1 Y ee
1.
fte
A flody
nt
d
at
qu In no ire D > 1 W Hou
ou e 4 8
2. re
bo M re reity is qu/JE e
to es id 2b re C : tim e 16
a) S tim
ic is IP ed loor tim e
b) ev Humor e or
en F
D 2a king nc te F
lo or tim
a) op lo or
3. b) ba re da e F lo
If fe
al l 1 2 F
re tim ve l
4. se d l 2a
Le ve 3
ag an e Le ve l
B e ur e Le ve
at st ur e
D Le
oi st ur e
M oi st ur
M oi st
M oi
M
M
RA
OS
Humidity indicator
Barcode label
Do not eat.
Avoid metal contact.
Discard if circles overrun.
bag opening.
Please check the HIC immidiately after
bake units
examine units, if necessary 15%
If wet,
bake units
examine units, if necessary 10%
If wet,
change desiccant
parts still adequately dry. 5%
If wet,
MIL-I-8835
Humidity Indicator
Desiccant
AM
OSR
OHA00539
Moisture-sensitive product is packed in a dry bag containing desiccant and a humidity card according JEDEC-STD-033.
L: Light
emitting
diode
L A E 6 7 6
´
Lead / Package Properties
6: folded leads
T: folded leads, improved corrosion stability
(Au-LF), w/o TiO2 jetting
7:
Encapsulant Type / Lens Properties
Colorless clear or white volume conversion
(resin encapsulation)
S: Silicone (with or without diffuser)
3: lens 30° … 70°
5: lens 40° .. 80°
Chip Technology:
5: HOP 2000
B: HOP 2000
C: ATON
D: Low cost ThinGaN/ Thinfilm
(e.g. 6mil)
F: Thinfilm InGaAlP
G: ThinGaN(Thinfilm InGaN)
(Subcon:Sapphire)
Notes
The evaluation of eye safety occurs according to the standard IEC 62471:2006 (photo biological safety of
lamps and lamp systems). Within the risk grouping system of this IEC standard, the device specified in this
data sheet fall into the class exempt group (exposure time 10000 s). Under real circumstances (for expo-
sure time, conditions of the eye pupils, observation distance), it is assumed that no endangerment to the
eye exists from these devices. As a matter of principle, however, it should be mentioned that intense light
sources have a high secondary exposure potential due to their blinding effect. When looking at bright light
sources (e.g. headlights), temporary reduction in visual acuity and afterimages can occur, leading to irrita-
tion, annoyance, visual impairment, and even accidents, depending on the situation.
Subcomponents of this device contain, in addition to other substances, metal filled materials including silver.
Metal filled materials can be affected by environments that contain traces of aggressive substances. There-
fore, we recommend that customers minimize device exposure to aggressive substances during storage,
production, and use. Devices that showed visible discoloration when tested using the described tests above
did show no performance deviations within failure limits during the stated test duration. Respective failure
limits are described in the IEC60810.
For further application related information please visit www.osram-os.com/appnotes
Disclaimer
Attention please!
The information describes the type of component and shall not be considered as assured characteristics.
Terms of delivery and rights to change design reserved. Due to technical requirements components may
contain dangerous substances.
For information on the types in question please contact our Sales Organization.
If printed or downloaded, please find the latest version on the OSRAM OS website.
Packing
Please use the recycling operators known to you. We can also help you – get in touch with your nearest
sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of
transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we
shall have to invoice you for any costs incurred.
In case buyer – or customer supplied by buyer – considers using OSRAM OS components in product safety
devices/applications or medical devices/applications, buyer and/or customer has to inform the local sales
partner of OSRAM OS immediately and OSRAM OS and buyer and /or customer will analyze and coordi-
nate the customer-specific request between OSRAM OS and buyer and/or customer.
Glossary
1)
Brightness: Brightness values are measured during a current pulse of typically 25 ms, with an internal
reproducibility of ±8 % and an expanded uncertainty of ±11 % (acc. to GUM with a coverage factor of
k = 3).
2)
Reverse Operation: This product is intended to be operated applying a forward current within the
specified range. Applying any continuous reverse bias or forward bias below the voltage range of light
emission shall be avoided because it may cause migration which can change the electro-optical char-
acteristics or damage the LED.
3)
Wavelength: The wavelength is measured at a current pulse of typically 25 ms, with an internal repro-
ducibility of ±0.5 nm and an expanded uncertainty of ±1 nm (acc. to GUM with a coverage factor of k =
3).
4)
Forward Voltage: The forward voltage is measured during a current pulse of typically 8 ms, with an
internal reproducibility of ±0.05 V and an expanded uncertainty of ±0.1 V (acc. to GUM with a coverage
factor of k = 3).
5)
Thermal Resistance: Rth max is based on statistic values (6σ).
6)
Typical Values: Due to the special conditions of the manufacturing processes of semiconductor devic-
es, the typical data or calculated correlations of technical parameters can only reflect statistical figures.
These do not necessarily correspond to the actual parameters of each single product, which could dif-
fer from the typical data and calculated correlations or the typical characteristic line. If requested, e.g.
because of technical improvements, these typ. data will be changed without any further notice.
7)
Characteristic curve: In the range where the line of the graph is broken, you must expect higher differ-
ences between single devices within one packing unit.
8)
Tolerance of Measure: Unless otherwise noted in drawing, tolerances are specified with ±0.1 and
dimensions are specified in mm.
9)
Tape and Reel: All dimensions and tolerances are specified acc. IEC 60286-3 and specified in mm.
Revision History
Version Date Change