Professional Documents
Culture Documents
Tread Moving Guide
Tread Moving Guide
S A F E T Y I N F O R M AT I O N 02
D I S A S S E M B LY F O R M O V I N G 03
PA R T S C H E C K L I S T 06
PA C K I N G R E C O M M E N D AT I O N S 07
L O C AT I O N R E Q U I R E M E N T S 07
1
S A F E T Y I N F O R M AT I O N MOVING WITHIN A ROOM
Read all precautions and instructions in D A N G E R : To reduce risk of electric Never attempt to transport the Peloton Tread with fewer than two people.
this guide before moving the Tread. shock, do not connect power until directed.
If the Tread does not need to pass through a doorway or other narrow
The Peloton Tread was not designed for D A N G E R : To reduce risk of electric space, you can roll it on the incline wheels.
assembly and installation by consumers. shock, the top left monitor bolt must be
The Peloton Tread Assembly Guide is grounded using the green wire. y y Before moving the Tread, set the incline to 2% or higher to raise
intended to assist trained, professional the front feet.
installers, using specialized tools, in Some components may have sharp y y Make sure to power down and unplug the Tread before moving it.
disassembling, assembling, and moving edges. Be careful with Tread parts during y y Have one person stand behind the monitor, holding the handrail.
the Peloton Tread. The Peloton Tread assembly and disassembly. y y Have one or two people lift the deck from the back, using the
is extremely heavy and requires more handholds on the rear end caps.
than one person to assemble and/ Do not move, assemble, disassemble, or y y Tilt the Tread forward to rest on the incline wheels.
or move. Improper assembly of the lift the Tread or Tread deck with fewer than y y Slowly and carefully roll the Tread backward or forwards.
Peloton Tread can lead to serious injury. two people.
Damage or equipment failure resulting
from the improper or negligent assembly, Fully assemble, test, and inspect the Tread
disassembly or relocation will not be before using.
covered under Peloton’s warranties. If you
use this Assembly Guide to assemble, Read the Peloton Tread user manual
disassemble, or move the Peloton Tread, for full safety information and usage
you do so entirely at your own risk. By instructions before operating the Tread.
undertaking disassembly or assembly of
your Peloton Tread, you agree to waive and SAVE THESE INSTRUCTIONS FOR
release Peloton from any and all claims FUTURE REFERENCE.
that you may have resulting from the
disassembling, assembling or moving of
the Peloton Tread by anyone other than a
trained professional.
If you need to move the Tread between rooms, floors, or buildings, you will
need to partially disassemble it.
PA R T S
1 Touchscreen
2 Monitor mount
3 Monitor mount cap
4 Monitor mount back cover
5 Tray
6 U-Rail
7 Right front end cap
8 Left front end cap
9 Incline wheel
10 Fabric side panel
11 Deck
12 Leveling foot
13 Left upright
14 Right upright
15 Left elbow cover
16 Right elbow cover
REQUIRED TOOLS
B E F O R E Y O U S TA R T
3 4
1 Snap off the elbow covers. 1 Remove the end cap safety screws and the end caps.
2 Disconnect two cables at the right elbow. 2 Peel back the front of the fabric side panels. Cut two clips along the
3 Have someone support the U-rail as you unscrew the six U-rail bolts. bottom edge to reveal the bottom of each upright.
Remove the U-rail. 3 Unscrew six bolts from the right upright. Remove the upright from the
deck and and unplug two cable connectors.
N O T E : you may need to snip a zip tie to release the cables.
4 Unscrew six bolts from the left upright and remove the upright from
the deck.
1 2 1 3
3 3 4
1 Tread deck
2 Monitor mount cover
3 Monitor mount cap
5 6 7 8
4 Monitor bolts (4)
5 Smart Card power cord
6 Touchscreen
7 Elbow covers (2)
8 U-rail with monitor mount and tray attached
9 U-rail bolts (6)
10 End caps (2)
11 End cap safety screws (2) 9 10 11 12
12 Upright bolts (12)
13 Uprights (2)
14 Power cord
15 Safety key
13 14 15
If you plan to order the Tread reassembly service from Peloton, make For more information on appropriate outlets, see the Peloton Support site.
sure that all Tread parts are present in the room where the Tread will be
assembled before the installers arrive. The reassembly service does not
include moving the Tread.
20"
PL ACEMENT
y y Allow a clearance of 78.7” in back and 20” on all other sides of the
assembled tread.
y y Allow additional space alongside or behind the Tread for floor workouts. 78.7" 20"
y y The Tread deck can incline to a height of 18.” Make sure the ceiling
above the Tread is free of obstructions and 2’ higher than the height of
the tallest user.
y y Install the Tread on a hard, flat, stable surface. Do not put it on a thick
carpet or a rug or mat that could curl or wrinkle. 20"
y y The Tread is for indoor home use only. Do not store the Tread outdoors,
near water, or at high humidity levels.
TOOLS 1. I N S TA L L T H E U P R I G H T S
Ratchet driver (3/8” drive) 1 Plug the two cables at the front of the deck into the right upright.
Torque wrench (3/8” drive) Push the excess cable into the deck
8 mm hex bit 2 Fit the right upright into the tab on the deck. Add six bolts and
5 mm hex bit hand-thread them.
Phillips head screwdriver 3 Add the left upright to the tab on the other side, and hand-thread the
4 fabric panel clips* other six upright bolts.
27 mm wrench or adjustable wrench
B E F O R E YO U S TA R T 1
y y Check that all parts from the parts checklist are present and undamaged.
y y Make sure that the location chosen for the Tread fulfills all the requirements
listed above.
y y Make sure you have at least two people available to complete the assembly
process.
2 3
1 Fit the U-rail into the uprights. 1 Tighten the 12 upright bolts to 25 lb-ft of torque.
2 Add the center bolt on each side. Then add the four remaining bolts and 2 Add two clips or zip ties to the lower edge of each fabric side panel to
tighten all six to 15 lb-ft/180 lb-in of torque. fasten them into place.
3 Connect the cables coming from the right upright to the ones coming 3 Fit the front end caps onto the corners of the deck. The left and right end
from the U-rail. caps are labeled L and R. Make sure the fabric panels are tucked in.
4 Snap on both elbow covers. Keep your hands clear of the seams and 4 Add a safety screw underneath each end cap.
make sure the red gasket is visible between the elbow cover and the rail.
1 2 3
3 4
1 Fit the touchscreen onto the mount while a second person secures it. 1 Check the deck. If it rocks or wobbles when you press down on one of
2 Attach the green grounding wire to the top left monitor mount bolt. the back corners, it needs to be leveled.
Secure all four bolts to 5 lb-ft/60 lb-in of torque. 2 Use a 27 mm wrench or an adjustable wrench to loosen the nut above
One bolt MUST be grounded. Attach the green grounding wire each back foot.
to the top left bolt. 3 Unscrew one or both back feet until all four deck feet rest firmly on
3 Plug the Smart Card cable into the back of the touchscreen. the ground.
4 Snap on the monitor mount cover and cap. N O T E : The front feet are not adjustable. Do not attempt to modify the
front feet.
4 Retighten both nuts.
1 2 2
3 4
1 Plug the power cord into the tread and the power supply into an outlet.
2 Return the Safety Key to the console.
3 Switch on the Tread and log into a WiFi network.
4 Access and run the Home Installer App from the Settings menu. Test all
features and functions of the Tread before using it.
1 2