Professional Documents
Culture Documents
FN 1
FN 1
FN 1
2 / 2 pts
The point in a beam where the negative moment changes to positive moment
Correct!
inflection point
Correct Answers
inflection point
point of inflection
Question 2
2 / 2 pts
rebars required to be placed at the corner of slab openings or at the corner of cantilevered
balconies
Correct!
3 pcs. diagona
Correct Answers
diagonal bar
diagonal bars
Question 3
2 / 2 pts
required distance in L of extra top bars of beams from the face of column supports
Correct!
1/3
Correct Answers
L/3
1/3
l/3
Question 4
2 / 2 pts
required distance in L of extra bottom bars of beams from the face of column supports
Correct!
Correct Answers
1/4
l/4
L/4
Question 5
2 / 2 pts
A mixture consisting of vehicles or binders, with or without coloring pigments, adjusted and
diluted with correct amounts and types of additives and thinners, which when applied on a
surface, forms as adherent continuous film which provides protection, decoration, sanitation,
identification and other functional properties.
Sealant
Stickwell
Correct!
Paint
Thinner
Question 6
2 / 2 pts
The minimum length of splice needed for column.
50 cm
Correct!
60 cm
40 cm
30 cm
Question 7
2 / 2 pts
Consistency or plasticity of concrete mixes is measured with
Correct!
Slump test
Slump mix
Slump analysis
Slump cone
Question 8
2 / 2 pts
The metal that has the highest electrical and thermal conductivity and is ductile, malleable
and non-magnetic is
Tin
Zinc
Brass
Correct!
Copper
Question 9
2 / 2 pts
A hard, brittle, chemically inert substance produced by fusing silica together with a flux and
a stabilizer that cools to a rigid condition without crystallization is
Correct!
Glass
Brazing
Welding
Soldering
Question 10
0 / 2 pts
A stone that is cut into a specific size, 2 feet or more in length and squared to dimension and
to a specific thickness is
Brick
You Answered
Rubble stone
Correct Answer
Dimension stone
Ashlar
Question 11
2 / 2 pts
The two (2) general types of welding are
Correct!
Question 12
2 / 2 pts
In structural steel section joints, it is recommended NOT to use
rivets
Correct!
oxy/acetyline welding
Question 13
0 / 2 pts
Minimum number of days for a compressive stength test
14 days
You Answered
28 days
21 days
Correct Answer
7 days
Question 14
0 / 2 pts
Which of the ff steel sections can be used to fabricate a steel roof rafter?
Z bar
square bar
You Answered
Flat bar
Correct Answer
Tubular
Question 15
2 / 2 pts
The top chord of a truss resists what type of forces?
Axial
Correct!
Compression
Tension
Lateral
Question 16
2 / 2 pts
Splicing of top bar of a beam recommended location
Correct!
midspan
¼ span
at support
1/5 span
Question 17
2 / 2 pts
____________weld is made by depositing filler material in a groove between two members to
be joined
Correct!
groove
Correct Answers
groove weld
groove welds
groove
Question 18
0 / 2 pts
In a ________________ beams and girders may be connected to columns where the bottom
flange of the beam rests on and is field-riveted to an angle shop-riveted to the flange or web
of the column. Another angle is field-riveted to the column and to the top flange of the beam
You Answered
w elded conne
Correct Answers
upright connection
seated connection
Horizontal connection
framed connection
Question 19
2 / 2 pts
In a _______________________ beams and girders may be connected to columns where the
web of the beam or girder is connected by angles or by gusset-plates to the column. In this
connection, angle seats are usually shop-riveted to the columns to hold the beam or girder
during erection.
upright connection
seated connection
Horizontal connection
Correct!
framed connection
Question 20
0 / 2 pts
___________________or moment connections is a steel beam connection where it is able to
hold their original angle under loading by developing a specified resisting moment, usually
by means of plates welded or bolted to the beam flanges and the supporting column.
upright connection
seated connection
Correct Answer
You Answered
fixed connection
Question 21
0 / 2 pts
is made of a circular hole (plug) or an elongated hole (slot) in one member of a lap joint,
joining that member to the portion of the surface of the other member that is exposed
through the hole
You Answered
plug weld
Correct Answer
slot weld
Question 22
2 / 2 pts
What is the minimum concrete cover for bars 20mm (no. 6) and larger for shells and folded
plate members for cast-in-place concrete but not exposed to the earth?
30 mm
Correct!
20 mm
25 mm
15 mm
Question 23
2 / 2 pts
The tendency of most materials to move or deform overtime under a constant load. The
amount of movement varies enormously depending upon the material. The area that is highly
stressed will move the most. The movement causes stresses to be redistributed.
Correct!
creep
deflection
buckling
fatigue
overload
Question 24
2 / 2 pts
What is the equivalent diameter in millimetre of a Number 5 deformed bar?
10 mm
12 mm
Correct!
16 mm
20 mm
Question 25
2 / 2 pts
Standard height and length of a 4” Concrete Hollow Block in mm?
150 x 400
150 x 300
100 x 200
Correct!
200 x 400