Professional Documents
Culture Documents
CIKO FloGrout
CIKO FloGrout
CIKO FloGrout
CIKO FloGrout
(PREVIOUSLY KNOWN AS CIKOGROUT HIFO)
Flowable, Non-shrink, high strength cement-based grout
1
Physical properties Soaking/priming
Form Powder Prior to grouting, fill the formwork with water and allow
Cement grey soaking of concrete surface for approximately 6 hours.
Colour Just before grouting, drain water completely from the
(standard)
W/P 0.13 - 0.15 formwork, anchor bolt pockets etc. by mechanical means
or using sponge so that the surface should be free from
Fresh Density ≈2.35 ± 0.05kg/m3 standing water.
Alternatively, and in purpose of increasing the bond
strength, it is applicable to prime the concrete substrate
Maximum Aggregate
3 mm with one of the bonding agents among CIKOBond wide
size
range of products. Consult CIKO Technical Department
Flow Proprietary for further advise and support.
≥145%
ASTM C1437
(W/P=0.15) Mixing
Early height changes CIKO FloGrout is a ready to use material requiring only
0 to 3 % addition of 3.25 up to 3.75 litres of water for mixing a 25
of grout ASTM C940
Height change of kg bag. Measure the required amount of water for each
0 to 0.2% batch and dispense into concrete mixer or mixing vessel.
hardened cylinder
(at 1,3,7,28 days) Dispense gradually CIKO FloGrout powder into concrete
grout ASTM C1090
mixer whilst the mixer is in the running mode. Mix the
Compressive 1 day ≥30 N/mm2
grout for 4 to 5 minutes to achieve a homogenous and
strength 3 days ≥40 N/mm2
lump free grout.
ASTM C109 @ 7 days ≥60 N/mm2
(W/P=0.13) 28 days ≥70 N/mm2
Note: Chilled water must be used to attain optimum
Flexural strength 3 days ≥8 N/mm2 results, the recommended temperature of grout shall be
ASTM C348 @ 7 days ≥10 N/mm2 within 70C and 350C. Higher temperatures increase the
(W/P=0.13) 28 days ≥14 N/mm2 amount of mixing water needed for a given fluidity, limits
Application the working time and reduce the ultimate strength. Lower
10 to 120mm temperatures might induce bleeding, delays setting time
Thickness*
*Note: higher thickness may be achieved by adding 10mm aggregate
and impede early development of strength however it
with a ratio up to 40% by weight to the bag. Consult CIKO technical permits reducing the mixing water content to its
service department for further support. minimum for a given fluidity thus increase ultimate final
strength.
2
Precautions Technical Support
• Ambient temperature shall be between For any technical support, do not hesitate to contact
50-400C. CIKO team at any time as CIKO offers on and off-site
• The temperature of both the grout and
services to end users, specifier and contractors.
elements encountering the grout should
be in the range of 7°C to 35°C.
• Do not overwork and avoid using More from CIKO Middle East
mechanical vibration. A wide range of construction chemical products are
• Do not re-temper CIKO FloGrout with manufactured by CIKO Middle East which includes:
water after mixing. ➢ Concrete admixtures and additives
➢ Waterproofing and damp-proof coatings
Health & safety ➢ Surface treatments
Use standard dust mask to avoid inhalation of ➢ Flooring and toppings
dust. Powder when wet or moist can cause ➢ Grouts and anchors
burns to skin and eyes which should be ➢ Tile adhesives and grout
protected during use. If encounters skin/eyes, ➢ Adhesives and bonding agent
flush with plenty of fresh water and seek medical ➢ Concrete repair materials
advice.
➢ Protective coating
Refer Material Safety Data Sheet for further ➢ Joint Sealants
details. ➢ Moulding compounds
4