Professional Documents
Culture Documents
Ice Maker - VS-625FS
Ice Maker - VS-625FS
Ice Maker - VS-625FS
Fla k e Ic e M a k e r
V
VSS--662255F,FS
F,FS
Op
Wear gloves Do not touch
for safety by wet hands
Keep room
Temperature Earth Ground
- 2 -
Caution VS-625F,FS
Caution in installation
1. Do not install in high temperature & humidity. Install on well ventilated place.
2. Install apart from wall by 30Cm. Please set on place which is plain & no vibration.
3. Do not install on flammable or explosive place.
4. Please clarify proper electronic source before using. (Voltage, Power)
5. Please use in place where the voltage variable rate is within ± 10 %.
6. Please use the ground outlet.
Caution in operation
1. Please keep the circumstantial conditions as temperature from 2℃ to 40℃, and
humidity lower than 80%. Unit may not operate correctly.
2. Do not put the plug with wet to prevent the electric shock.
3. Please keep the circumstantial temperature not to changed rapidly.
Humidity may caused on unit inside. And it can cause trouble on unit.
(If dew is foamed on chamber, clean with soft dry fabric.)
4. Please put the contents into ROTOR symmetrically with same weight of contents.
If not, unit is operated in UNBALANCE and causes the trouble.
5. If you use under room temperature, please operate the refrigerated before 30 minutes
from input contents.
If you put the contents into CHAMBER before getting the aimed temperature, contents
can be degenerated.
6. Once refrigerator is operated, do not touch the chamber in wet. Hand can be frozen or
stuck on chamber by cold.
7. Door is closed during rotation. Do not open by forced for safety.
After end of operation, DOOR can be opened but chamber is still rotating for a while.
Therefore, please put out the contents after rotor is fully stopped.
8. Door is made of PC Material. Do not make a shock .
9. While unit is running, water is exhausted by Drain Hose.
Make a drain method when you install the unit.
※ Be careful sliding accident by water on the floor.
Additional cautions.
1. Use mild detergent for cleaning.
2. In case of smoke, strange smell or Error occurs, cut off main power switch and inform
to contact our service center.
4. Do not alternate or repair by an unauthorized person.
- 3 -
Contents
- Composition .............................................. 5
- Check of composition...................................... 6
- Installation.............................................. 6
- Specification........................................... 7
- Feature ............................................. 8
- Safety ............................................ 8
◈ Operation .................................... 9
◈ Warranty ............................................ 12
- 4 -
Composition VS-625F,FS
▶ Composition
Front Rear
No Name Function
- 5 -
Composition VS-625F,FS
▶ Check of composition
▶ Installation
1. Install on place where is plane & no vibration. And apart from the wall by 30Cm.
3. Clean inside chamber after taking out Hose, Scoop, Manual and Punching shelve from
the chamber.
4. Put the punching shelve in the chamber. Punching shelve is the safety cover for dust.
5. Insert the Drain Hose (Blue color) in the Drain cock. Opposite of hose should be set
on lower place than drainpipe.
- 6 -
Specification VS-625F,FS
▶ Specification
VS-625FS VS-625F
Materials (out) Steel Steel & Steel with Powder Coating(Upper cover)
- 7 -
Operation VS-625F,FS
▶ Feature
1. Exterior and Interior CHAMBER are made of STAINLESS STEEL (SUS 304).
2. DOOR is used a translucent acrylic door that can block out light as much as
possible while checking inside. This Door is opened and closed easily.
3. FULL AUTOMATIC CONTROL is built in the unit, production of ice can be controlled
by automatic icing Control System
▶ Safety
- ICE LEVEL SENSOR : Chamber is filled with Ice, production is stopped by sensor.
- 8 -
Operation VS-625F,FS
▶ CONTROL PANEL
WATER LEVEL
ⓕ
ⓐ POW ER
ⓑ POWER PL
ⓔ
STATUS
ⓒ
SNOW FULL
Operating
Ready ⓓ
Check
Stop Sign
No Name Function
- 9 -
Operation VS-625F,FS
1. Check rear side of unit. There is a Power circuit breaker s/w. Turn it on.
2.Connect the supply hose into the water purifier or water pipe.
Turn on the water pipe.
When you open the water pipe, open it by using Valve on the hose connector.
(↶ : Open, ↷ : Close)
3. Press the Power button on CONTROL PANEL. LED lamp in the chamber is on.
"POWER P.L(Green)" and "WATER P.L(Red)" are blinking. Also, water is inserted after
solenoid valve is opened.
At this time, Green lamp on "STATUS P.L" is blinking. It means unit is ready for
started.
4. After water supply is finished, Water supply is stopped and "WATER P.L(RED)" is Off.
Drum is working 5Sec later.
13 sec is passed after drum start, “STATUS P.L”is turned to Green.
Compressor is start. 1 min later after compressor is working, Snow type of Ice is made.
6. If you want to make a stop while unit is working, press "POWER" BUTTON
STATUS P.L is turned to RED, LED Lamp , Drum and compressor are off.
("POWER P.L is blinking continually => Ice Maker is stopped)
If you want to work it again, press the "POWER" BUTTON.
After 3 minutes, Drum is working. After 30Seconds, compressor is working.
After 1 minutes, Ice is producted again.
7. Open the door, take out the ice as you want by using scoop.
Do not put wet hand into the chamber. After wear the safety gloves, use this
unit, please.
- 10 -
Operation VS-625F,FS
9. If you do not use this unit for long time, Turn off the "POWER" BUTTON on control
panel and power circuit breaker on rear of the unit.
Vale should be off.
※ If you do not use this unit for long time or if it is thundering, pull out the plug.
If not Fire or some damage can be occurred.
※ Reference
2. If unit would not working for long time, water and ice should be drained completely.
Then, wipe the moisture and water in chamber.
This guarantee is valid only if the unit has been used in accordance
with the instructions in this manual and for its intended purpose.
Vision Scientific Co., Ltd. shall not be responsible for consequential
damages or damages resulting from the abuse or misuse or this
equipment.
**This information will be required in the event that service becomes necessary.
(You can get these information from bar-code on rear part.)
- Specification (Description, Model No. , Serial No.)
- Date of Purchase.
- 11 -
Warranty
* Thanks to purchase products for
vision scientific CO., LTD.
Items Flake Ice Maker
* The product quality control and
strict inspection and testing by Model VS-625F, FS
product is issued.
Serial No.
- 12 -